Copyright 1998 D-Link Corporation.
Contents subject to change without prior notice.
D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc.
All other trademarks belong to their respective proprietors.
Copyright Statement
No part of this publication may be reproduced in any form or by any means or
used to make any derivative such as translation, transformation, or adaptation
without permission from D-Link Corporation/D-Link Systems Inc., as
stipulated by the United States Copyright Act of 1976.
Limited Warranty
Hardware:
D-Link warrants its hardware products to be free from defects in workmanship and materials, under normal use and
service, for the following lengths of time from the date of purchase from D-Link or its Authorized Reseller:
Product TypeWarranty Period
Network adaptersLifetime
Unmanaged and managed hubs (10Mbps)Lifetime *
Unmanaged and managed hubs (100Mbps)One year
Repeaters, MAUs , transceivers, media convertersOne year
ConcentratorsOne year
Internetworking productsOne year
* Power supply and fans in these devicesOne year
Other hardware productsOne year
Spare parts and spare kits90 days
If a product does not operate as warranted during the applicable warranty period, D-Link shall, at its option and
expense, (1) repair the defective product or part, (2) deliver to Customer an equivalent product or part to replace the
defective item. All products that are replaced will become the property of D-Link. Replacement products may be
new or reconditioned. Any replaced or repaired product or part has a ninety (90) day warranty or the remainder of
the initial warranty period, whichever is longer.
D-Link shall not be responsible for any software, firmware, information, or memory data of Customer contained in,
stored on, or integrated with any products returned to D-Link pursuant to any warranty.
All products with lifetime warranty have a standard five-year warranty. To qualify for lifetime warranty, the
enclosed Product Registration Card must be completed and returned to D-Link within ninety (90) days of
purchase.
Warranty service may be obtained by contacting a D-Link office within the applicable warranty period for a Return
Material Authorization (RMA) number. If a Registration Card has not been previously sent, proof of purchase, such
as a copy of the dated purchase invoice, must be provided. Once an RMA number is issued, the defective product
must be shipped back to D-Link prepaid, insured and wrapped in the original or similar shipping package to ensure
that it will not be damaged during shipment. When returning the defective product to D-Link for service, the RMA
number must be marked on the outside of the shipping package. Any product returned without an RMA number
shall be rejected and sent back to the Customer, and D-Link reserves the right to have Customer bear the cost of
sending back such products. A service charge may or may not be levied to Customer by D-Link. To find out if a
service charge is levied or not, and the charged amount, read the RMA that is returned to Customer, or ask the DLink office when an RMA is requested.
Software:
D-Link warrants that the software programs licensed from it will perform in substantial conformance to the
applicable published program specifications for a period of ninety (90) days from the date of purchase from D-Link
or its Authorized Reseller. D-Link warrants the magnetic media containing software against failure during the
warranty period. No updates are provided. D-Link's sole obligation hereunder shall be to replace any defective
software products with products which substantially conform to D-Link's applicable published specifications.
Customer assumes responsibility for the selection of the appropriate applications program and associated reference
materials. D-Link makes no warranty that its software products will work in combination with any hardware or
applications software products provided by third party, that the operation of the software products will be
uninterrupted or error free, or that all defects in the software product will be corrected. For any third party products
listed in the D-Link software product documentation or specifications as being compatible, D-Link will make
reasonable efforts to provide compatibility, except where the non-compatibility is caused by "bug" or defect in the
third party's product.
Warranty service for software products may be obtained by contacting a D-Link office within the warranty period.
Where no Product Registration Card has been sent by Customer, proof of purchase, such as a copy of the dated
purchased invoice, must be provided.
D-Link Offices to Contact for Warranty Service
To obtain an RMA number for warranty service, contact the D-Link office nearest you. A list of contact addresses
for D-Link’s international offices is found in the back of this User’s Guide. Your Warranty Registration Card
should also be sent to your regional D-Link office.
LIMITATION OF WARRANTIES
IF THE D-LINK PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, THE CUSTOMER'S SOLE
REMEDY SHALL BE, AT D-LINK'S OPTION, REPAIR OR REPLACEMENT. THE FOREGOING
WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES,
EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR
OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. D-LINK NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT
ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION MAINTENANCE OR USE
OF D-LINK'S PRODUCTS
D-LINK SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION
DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY
THE CUSTOMER'S OR ANY THIRD PERSON'S MISUSE, NEGLECT, IMPROPER INSTALLATION OR
TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR, OR ANY OTHER CAUSE BEYOND THE RANGE OF
THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING OR OTHER HAZARD
LIMITATION OF LIABILITY
IN NO EVENT WILL D-LINK BE LIABLE FOR ANY DAMAGES, INCLUDING LOSS OF DATA, LOSS OF
PROFITS, COST OF COVER OR OTHER INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES
ARISING OUT THE INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE OR
INTERRUPTION OF A D- LINK PRODUCT, HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY.
THIS LIMITATION WILL APPLY EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
IF YOU PURCHASED A D-LINK PRODUCT IN THE UNITED STATES, SOME STATES DO NOT ALLOW
THE LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES,
SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
•Four LED indicators: Full/Half Duplex, Link, Active, and Collision.
•Driver
†
support for:
√ Novell Netware 3.12 ODI√ Novell Netware 4.X ODI
√ Microsoft Windows 95√ Microsoft Windows 98
√ Microsoft Windows NT 3.51√ Microsoft Windows NT 4.0
√ ODI DOS
†
Check http://www.dlink.com for newest release of drivers.
Introduction2
DFE-500FX Fast Ethernet Adapter, with Fiber Optic Interface, for PCI Bus
22
Installation
Unpack and Inspect
CAUTION:Under ordinary circumstances, a DFE-500FX
card will not be affected by static charge as may
be received through your body during handling of
the unit. In special circumstances where you
may carry an extraordinarily high static charge, it
is good practice to reduce the charge by
touching a ground before handling the adapter
card.
Open the shipping carton and carefully remove all items. In addition to this
User's Guide, ascertain that you have:
•One DFE-500FX Ethernet Adapter Card.
•One 3.5" diskette: DFE-500FX Software Diskette.
Installing the Adapter
1. Shut down the computer, unplug its power cord, and remove the chassis
cover.
2. Insert the contact edge of the DFE-500FX card into the connector of any
available PCI Bus Master expansion slot. Press the card firmly into the
connector such that the card’s contacts are fully seated in the connector.
Installation3
DFE-500FX Fast Ethernet Adapter, with Fiber Optic Interface, for PCI Bus
3. Install the bracket screw which secures the card to the computer chassis.
4. Replace the computer’s chassis cover.
5. Reconnect the computer’s power cord, and switch computer power on. If
the BIOS section of your computer’s boot program is Plug-and-Play
compliant, then at power-up the BIOS will automatically configure any
newly installed DFE-500FX adapter.
NOTE: Due to a fault in some Plug-n-Play BIOS programs, it
happens occasionally that a newly installed adapter is
assigned an Interrupt Number which is already assigned
to another device. In such a case, the conflict of
Interrupt Number will cause faults in the behavior of
both devices. Then it is necessary to run the CMOS
Setup utility, and manually assign a non-conflicting
Interrupt Number.
Connecting the Network Cable
Multimode (62.5/125µm or 50/125µm) fiber cabling with an IEEE
recommended SC connector is required for the adapter. Use either one duplex
SC connector, or two simplex SC connectors, and observe the correct
relationship between the receive (Rx) and transmit (Tx) ports on the adapter
and repeater. If there is a need to monitor the adapter’s faceplate LEDs, make
the rear of the PC or workstation accessible and leave sufficient clearance for
cabling and service. The maximum length of fiber cable between any station
and its supporting hub is 2,000 meters at full-duplex and 412 meters at halfduplex.
Installation4
DFE-500FX Fast Ethernet Adapter, with Fiber Optic Interface, for PCI Bus
Software Installation
Vast varieties of network architecture considered, the instruction for driver
software installation are given as README files in the DFE-500FX Software
Diskette. Review the root directory README for overview information, and
for full installation details, see the README and referenced instruction files in
the subdirectory appropriate to your network operating system.
‡
‡
Check http://www.dlink.com for newest release of drivers.
Installation5
DFE-500FX Fast Ethernet Adapter, with Fiber Optic Interface, for PCI Bus
AA
Troubleshooting
If you experience any problems with the adapter, first: ascertain that the
appropriate driver is loaded; that the proper grade of cable is employed for the
network connection; and that the supporting hub is properly qualified for the
application (such as 100Base-FX).
The DFE-500FX Adapter features four LED indicators:
•FULL/HALF DUPLEX MODESteady green indicates the adapter is operating in Full Duplex mode. A
dark LED indicates the adapter is operating in Half Duplex mode.
•LINKSteady green indicates good linkage between the DFE-500FX and its
supporting hub.
•ACTIVE
Flashing green indicates activity (transmitting or receiving) within the
adapter.
•COLLISIONA yellow flash indicates data collisions in the segment. Intermittent
flashing of the collision LED is normal.
Troubleshooting6
DFE-500FX Fast Ethernet Adapter, with Fiber Optic Interface, for PCI Bus
BB
Specifications
Network Type:
•Ethernet 100Base-FX
Ethernet IEEE 802.3u standard for 100Mbps baseband CSMA/CD local
area network
Jumperless Hardware
Media interface: FDDI Transceiver SC Connector
LAN Chip Set:
•Interface controller: DEC DC21140
•Transceiver interface: Level One LXT970
EMI Certifications:
FCC Class BCE Certification, Class B
Host interface: PCI Bus (Bus Master)
I/O base address assigned by Plug and Play system
Interrupt Number Assigned by Plug and Play system
Physical Dimensions: 14 cm x 7.4 cm
Environment:
Storage:−20° to 80°C, (−4° to 176° F)Operating:0° to 55° C, (32° to 131° F)
Humidity:10% to 90% non-condensing
Weight: 76 grams
Power Consumption: 4W (Max.)
Specifications 7
DFE-500FX Fast Ethernet Adapter, with Fiber Optic Interface, for PCI Bus
PCB Layer: 4 layers
Device Drivers
§
√ Novell Netware 3.12 ODI√ Novell Netware 4.X ODI
√ Microsoft Windows 95√ Microsoft Windows 98
√ Microsoft Windows NT 3.51√ Microsoft Windows NT 4.0
√ ODI DOS
§
Check http://www.dlink.com for newest release of drivers.
Specifications 8
Registration Card
Print, type or use block letters.
Your name: Mr./Ms_______________________________________________________________________
Organization:_____________________________ Dept. _________________________________________
Your title at organization: __________________________________________________________________
Telephone:__________________________ Fax:_______________________________________________
Organization's full address: ________________________________________________________________
______________________________________________________________________________________
Country:______________ Date of purchase (Month/Day/Year):____________________________________
Product
Model
(* Applies to adapters only)
Product was purchased from:
Reseller's name: ________________________________________________________________________
Telephone:_______________________ Fax:__________________________________________________
Reseller's full address: ___________________________________________________________________
______________________________________________________________________________________
1. Where and how will the product primarily be used?
oHome oOffice oTravel oCompany Business oHome Business oPersonal
2. How many employees work at installation site?
o1 employee o2-9 o10-49 o50-99 o100-499 o500-999 o1000 or more
3. What network protocol(s) does your organization use ?