D-link DES-1005P User Manual

Page 1
DES-1005P
5-Port 10/100Mbps with
1-Port PoE Unmanaged Switch
Manual
RECYCLABLE
V1.01
Page 2

TABLE OF CONTENTS

About This Guide ................................................................................. 1
Purpose
Introduction
Fast Ethernet Technology Switching Technology Power over Ethernet (PoE) Features
Unpacking and Installation
Unpacking Setup Connecting Network Cable
Identifyi ng External Components
Front Panel Rear Panel
Understanding LED Indicators
Syst em LED
PoE Rule Mounting the Switch on a Wa l l Technical Specifications
............................................................................................. 1
.......................................................................................... 2
................................................................ 2
..................................................................... 3
.............................................................. 4
............................................................................................ 4
.................................................................. 5
........................................................................................ 5
................................................................................................ 5
.............................................................. 6
........................................................ 7
....................................................................................... 7
........................................................................................ 8
............................................................ 9
..................................................................................... 9
........................................................................................ 10
......................................................... 11
.................................................................... 12
i
Page 3
Page 4

ABOUT THIS GUIDE

Congratulations on your purchase of the D-Link DES-1005P. This device integrates 100Mbps Fast Ethernet and 10Mbps Ethernet network capabilities in a highly flexible package. Port-1 on the switch supports Power over Ethernet (PoE), meaning it will automatically detect the presence of an IEEE 802.3af-compliant powered device (PD) and provide power through the port. The switch provides up to 15.4 W per PoE port and can be used to power WLAN access points, IP phones, video cameras, and other PD devices. The Switch will automatically detect the network appliance’s requirements, and will supply the required power to each appliance accordingly.

Purpose

This manual will familiarize you with the DES-1005P and guide you through the installation process.
1
Page 5

INTRODUCTION

Fast Ethernet Technology

The growing importance of LANs and the increasing complexity of desktop computing applications are fueling the need for high performance networks. A number of high-speed LAN technologies have been proposed to provide greater bandwidth and improve client/server response ti mes. Among them, 100BASE-TX (Fast Ethernet) provides a non-disruptive, smooth evolution from the current 10BASE-T technology.
100Mbps Fast Ethernet is a standard specified by the IEEE 802.3 LAN committee. I t is a n exten sion of t he 10M bps Et herne t stand ard with th e ability to transmit and receive data at 100Mbps, while maintaining the CSMA/CD Ethernet protocol. Since the 100Mbps Fast Ethernet is compatible with all other 10Mbps Ethernet environments, it provides a straight forward upgr ade a nd ta kes ad vantage of t he exis ting i nvest ment in hardware, software, and personnel training.
2
Page 6

Switching Technology

Switching is a cost-effective way of increasing the total network capacity available to users on a local area n etwork. A switch increases capacity and decreases network loading by dividing a local area network into different segments, which don’t compete with each other for network transmission capacity.
The switc h ac ts a s a hi gh-speed selective bridge between the individual segments. The switch, without interfering with any other segments, automatically forwards traffic that needs to go from one segment to another. By doing this the total network capacity is multiplied, while still maintaining the same network cabling and adapter cards.
Switching LAN technology is a mar ked imp ro ve me nt o ver t he p revious generation of network bridges, which were characterized by higher latencies. Routers have also been used to seg ment local area networks, but the cost of a router, the setup and maintenance required make routers relatively impractical. Today switches are an ideal solution to most kinds of local area network congest i on probl ems .
3
Page 7

Power over Ethernet (PoE)

Power over Ethernet (PoE) integrates power and data onto one single cabling infrastructure, eliminating the need to have AC power available at all locations.
Power and D ata i s i nt e gr at ed o nto the same cable, supporting category 5/5e up to 100 Meters. PoE will provide power to PoE compatible devices, such as IP telephones, wireless LAN access points and IP security cameras.
PoE is already widely adopted in the market, saving up to 50% of overall installation costs by eliminating the need to install separate electrical wiring and po wer outle ts.

Features

5 ×10/100Mbps Auto-negotiation Fast Ethernet RJ45 ports with
1-port PoE funct i on (port-1)
Compliant with 802.3af specif ic a tion Supports PoE power up to 15.4W for PoE port Supports PoE IEEE802.3af compliant Powered Device (PD) Each port supports auto MDI/MDIX, so there is no need to use
cross-over cables
Full/half duplex transfer mode for each port Wire speed reception and transmission 64KBytes packet buffer Supports IEEE 802.3x flow control for full-duplex mode ports Supports Back-pressure flow control for half-duplex mode ports
4
Page 8

UNPACKING AND INSTALLATION

Unpacking

Open the box and carefully unpack it. The box should contain the following items:
One DES-1005P One External Power Adapter Wall Mount Kit Four rubber feet Quick Installation Guide
If any item is found missing or damaged, please contact your local reseller for replacement.

Setup

The setup of the DES-1005P can be performed using the following steps:
The power outlet should be within 1.82 meters (6 feet) of the
Switch.
Visually inspect the DC power jack and make sure that it is fully
secured to the power adapter.
Do not cover the ventilation holes on the sides of the Switch,
and make sure there is adequate ventilation around it.
Do not place heavy objects on the switch.
5
Page 9

Connecting Network Cable

The Switch support 5 10/100Mbps Ethernet ports and Port 1 PoE Enabled port, the PoE port will automatically activate when a compatible terminal is identified. The Switch will supply power through the Ethernet port to the connected PoE powered device (PD).
For legacy devices that are not compatible, the PoE port will not offer power to this device. This feature allows users to freely and safely mix legacy and Power over LAN compatible devices on their network.
The Switch supports 10Mbps Ethernet or 100Mbps Fast Ethernet and it runs both i n half and full du plex mode using two pa ir of Cat egor y 5 cable.
These RJ45 ports are Auto-MDI type port. The Switch can auto negotiate to MDI-II or MDI-X type, so you can connect any RJ-45 cable regardless if it is a standard or crossover cable.
6
Page 10

IDENTIFYING EXTERNAL COMPONENTS

Front Panel

The figure below shows the front panels of the DES-1005P.
Figure 1. Front panel
Power LED Indicator:
This green indicator light is on when the DES-1005P is receiving power; otherwise, it is off.
Ethernet Ports (Port 1~5):
These ports support network s peeds of e ith e r 10Mbps or 100Mbps, and can operate in half- and full- duplex transfer modes. These ports also support automatic MDI/MDIX crossover detection, which gives the Switch true , “plug and play” capabilities. Just connect any network cable between the Switch and the device, and The Switch will automatically detect the settings of the device and adjust itself accordingly.
PoE Port (Port 1 only):
The PoE port will automatically activate when a compatible terminal is identified. The Switch will supply power through the Ethernet port to the connected PoE device.
For legacy devices that are not compatible, the PoE port will not offer the po wer to this device. This feature allows users to freely and safely mix legacy and PoE com pat ible devic es on the network.
7
Page 11

Rear Panel

The figure below shows the fro nt panels of the DES-1005P.
Figure 2. Rear panel
DC Power Jack: Connect to the power adapter
Power Switch: Use to turn on/off the Switch
8
Page 12
LED
Color
Status
Description
Power
Green Solid Light
Power o n
Off Light
Power off
Blinking
When there is reception or transmission Off
No link
Location
LED Indicative
Color
Status
Description
PoE Port
PoE Status
Green
Solid Light
When the PoE powered
Green
Blinking
Overload/Sho r t cir cuit
within 5s after turn off power.
Off
Light Off
No Powered Device (PD) connected.

UNDERSTANDING LED INDICATORS

The front panel LEDs provides instant status feedback, and helps monitor and troubleshoot when needed.
Figure 3. LED indicators of the Switch

System LED

LED Indicators
Indicative
(per devic e)
Link/Act
(per port)
PoE LED Indicators
Green Solid light When there i s a secure connection (or li nk)
to device at any of the ports.
occurring at any of the ports.
device (PD) is connected and the port supplies power successfully.
occurred. PSE will turn off power and blink the LED 2 seconds. After 2s, LED will be off. PSE will auto-recovery
9
Page 13

PoE Rule

1. Supplies power to PD device, meeting IEEE802.3af standards. It
is able to provide power to PD devices more sufficiently.
2. Auto discovery feature, automatically recognize the connection of
PD device and immediately sends power to it
3. Active circuit protection, automaticall y d isables the port if there is
a short while other ports remain active
4. Auto disable port via two different methods as below:
a. Over Current Protection
- 802.3af mode: if the current is over 375mA while other ports remain active, the port will be auto disabled.
b. Over Output Power Limit
- 802.3af mode: if the port is over 15.4W while other ports remain active, the lo wer prio rity port will be auto disabled.
5. DES-1005P should follow the standard PSE pin-out standard of
Alternative A which is sending out power over number 1,2,3,6 pins of 8 wires of CAT5 UTP cable
6. DES-1005P works with all D-Link 802.3af devices DES-1005P
works with all non-802.3af capable D-Link AP, IP Cam and IP phone via DWL-P50
10
Page 14

MOUNTING THE SWITCH ON A WALL

The DES-1005P can also be mounted on a wall. Two mounting slots are provided on the bottom of the switch for this purpose. Please make sure that the front panel is exposed in order to view the LEDs. Please refer to the illustration below:

A.) Mounting on a c ement wall

1. Mount the Nylon screw anchors into a cement wa ll.
2. Drive the T3 x 15L screws into the Nylon screw anchors.
3. Hook the mount ing holes of th e switch back on the screws;
you have completed the wall-mount.

B.) Mounting on a wood wall

1. Drive the T3 x 15 L screws into the wood wall.
2. Hook the mounting holes o f the switch back on the screws;
you have completed the wall-mount.
(1) 3/4 inch minimum
for wood wall
(2) 3 inch minimum
for cement wall.
11
Page 15

TECHNICAL SPECIFICATIONS

General
Standards IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3x Full Duplex Flow Control
IEEE 802.3af Power over Ethernet Protocol CSMA/CD Data Transfer Rate Ethernet: 10Mbps (half duplex), 20Mbps (full-duplex)
Fast Ethernet: 100Mbps (half duplex), 200Mbps (full-duplex) Topology Star Network Cables 10BASET: 2-pair UTP Cat. 3, 4, 5; up to 100m
100BASE-TX: 2-pair UTP Cat. 5; up to 100m Number of Ports 5 × 10/100Mbps Auto-MDIX RJ45 ports with POE enabled (port 1)
Physical and Environmental
DC inputs 48VDC/0.5A Power
Consumption
Temperature
Humidity Operating: 10% ~ 90%, Storage: 5% ~ 90% Dimensions 5.5 x 3.3 x 1.1 inches EMI: FCC Class B, CE Class B Safety: UL/LVD
Maximum: (PoE off. No Powered Devices connected)
DC input: 2.05 Watts
AC input: 2.7 Watts
Maximum: (PoE on. While consuming all 15.4W power budget)
DC input: 17.29 Watts
AC input: 20.2 Watts
Operating: 0° ~ 40° C, Storage: -40° ~ 70° C
12
Page 16
Performance
RAM Buffer: 64K bytes per device Filtering Address Table: 1K entries per device Packet Filtering/Forwarding Rate: 10Mbps Ethernet: 14,880/pps
100Mbps Fast Ethernet: 148,800/pps MAC Address Learning: Automatic update Transmits Method: Store-and-forward
13
Loading...