
DWL-AG700AP Install Guide
Version 3.00
ANT24-Series
ANT70-Series
D-Link Antenna Kits
User’s Guide

2
ANT24-0700 Install GuideSystem Requirements
D-Link Antenna-kit Installation Guide
Installation
(If needed)
Install the surge protector. (You can install with
optional ANT24 series low loss cables)
Note:
/antenna
With Surge protector adaptor on an outdoor serial is
attached to the lightning protestion system (ground)
of the bu il ding. All devices downs tream are then
protected by the ground from lightning strikes.It can
protect your sensitive WLAN equipments from high
voltage surges caused by dischargeand transients
at the antennas. It will be integrated in the cabling
system between the antenna and the coax-cable and
must have direct ground contact.

3
System Requirements
Installation
D-Link Antenna-kit Installation Guide
Surge protector
Installation guide
for outdoor antenna-kit
Step 1
loosen the screw from the surge protector.
Step 2
get a normal conductive copper wire with 2 sides stripped long enough to be conductive,
these wires can lead high voltage surges into the grounding.
Remark:
(1) for the ground screw you use, we suggest the longer (deeper into ground) the better performance it has.
(2) please use a copper wire with diameter at least from 2.0mm, the thicker the diameter, the higher
voltage it can sustain.
Option (1)
Option (2)
Ground
Step 3
find a conductive material nearby the antenna installation sites, connect another end of the wire
into position, there are several options:
(1) Use a long screw to stick into the ground tightly, connect another wire onto.
(2) fix or solder another end of wire onto a steel material/ bar under steel construction,
such as wall for buildings, railings or other conductive materials which set up from
the ground.

4
ANT24-0700 Install GuideSystem Requirements
ANT24-Series
Regulations
2.4GHz~2.5GHz 5.15GHz~5.35GHz5.47~5.725 5.75GHz~5.875GHz
point to multi-point
point to point
point to multi-point 36dBm 36dBm
point to point
30+6(antenna gain ) dBm
then above 30dBm, one dB output
power reduced, then 3dB antenna gain
increased
30+23(antenna gain)
then above 30dBm, one dB output power
reduced, then 3dB antenna gain increased
For outdoor use
X
FCC
23dBm
ETSI
20dBm ave.
23dBm peak.
23dBm 30dBm
X
EIRP limitaton:
EIRP = Effective,Isotropic Radiated Power
= Device Output Power + Antenna Gain - Cable Loss
Model Cable Type Length Interface
Cable loss (dB)
@ 2.4GHz
Cable loss(dB)
@5GHz
ANT24-CB03N LMR400 3m N plug to N jack 1 1.75
ANT24-CB06N LMR400 6m N plug to N jack 1.85 2.7
ANT24-CB09N LMR400 9m N plug to N jack 2.6 3.8
Note:
1. The loss value includes two connectors ( around 0.3~0.4dB @ 2.4GHz, 0.39~0.52dB@5GHz).
2. The longer cable you use, the more attenuation it causes, therefore, the extended range might be
shorten then a normal link with default cables.
3. To comply with EU regulation, please use longer cables which can cause enough attenuation value.
4. For more detail of connectors type, please refer to the appendix page.(P.30)
Cable Loss
D-Link WLAN Antenna-Kit
Extended range differentiation for FCC/CE regulated regions
CE ETSI EN 300 328 regulated European Union (EU) regions
Based on ETSI EN 300 328, the system device and its antenna Emitted Isotropic Radiated Power
(EIRP) are limited to operate within a 20dBm gain. The range extension provided by the antenna
kit should comply with the restrictions set by the EU.
FCC regulated regions (US, Canada, etc.)
Using the same antenna-kit in FCC-regulated regions, the extended range may extend farther than
CE-regulated antennas due to a higher output power allowance (FCC limits EIRP emissions to
36dBm).
The usage of high gain antennas must be properly set to comply with EU regulations, and
additional consideration should be made to avoid potential health hazard. Consult a professional
installer for every occasion of application.
Outdoor Installations
To fully benet from D-Link’s extensive range of quality outdoor antennas, please note that they
should be installed by a professional and must comply with the Europe Union CE wireless radio
frequency output power. Cable length will affect the antenna gain dramatically.

6
ANT24-0700 Install GuideSystem Requirements
ANT24-Series
D-Link ANT24-0401
Ceiling Mount Antenna
Electrical specication
Environmental & Mechanical Characteristics
Temperature -10°C to 55°C
Humidity 100% @ 25 C
Lightning protection DC ground
Radome color white
Radome material ABS
Weight 100gw
Dimensions 132 x 42 mm
120
58°~75°
110g without joint

7
System Requirements
ANT24-Series
D-Link ANT24-0500
Indoor/Outdoor
Omni-Directional Antenna
Electrical specication
Environmental & Mechanical Characteristics
Survival wind speed 180 km/hr
Temperature -40 C to +80 C
Humidity 100% @ 25 C
Lightning protection DC ground
Radome color Gray-white
Radome material Fiberglass
Radiator material Micro striple line
Weight 0.8kgw
Dimensions 330 x 19 mm
90
o
180
o
150
o
120
o
60
o
30
o
0
o
-150
o
-90
o
-120
o
-60
o
-30
o
-3
-10
-20
-30
Version 1
H-plane Co-polarization Pattern
90
o
180
o
150
o
120
o
60
o
30
o
-150
o
-90
o
-120
o
-60
o
-30
o
-3
-10
-20
-30
V-plane Co-polarization Pattern
0
o

8
ANT24-0700 Install GuideSystem Requirements
D-Link ANT24-0501
Indoor Omni-Directional Antenna
Electrical specication
Physical Properties
Package Contents
-One ANT24-0501 2.4GHz indoor 5dBi omnidirectional Antenna with 1.5M extension cable and
RP-SMA Jack connector
-One RP-SMA/ RP-TNC adaptor
-One registration card and international ofce guide
-Mounting kit includes:
-Two Crews
-Two plastic xings
-One sticker
Frequency Range 2400~2500MHz
Impedance 50Ω Normal
VSWR 1.92 Max
Return Loss -10 dB Maximum
Antenna Structure Helis antenna
Peak Gain ( w/o cable loss) 5dBi
Admitted Power 1 W
Cable loss( 1.5m) 2.1dB@2.45GHz
E-Plane 36 deg.
H-Plane 360 deg.
Cable RG-178 50Ω
Cable length 1.5 M
Cable color Gray
Connector Reverse SMA plug
Antenna Material ABS, ABS+PC
Operating Temp -20°C ~ +65°C
Storage Temp -30°C ~ +75°C
Color Antenna: Metallic gray and silver
Base: Metallic gray
0
345
330
315
300
285
270
255
240
225
210
195
180
165
150
135
120
105
90
75
60
45
30
15
-20 -10 0
dB
Far-field amplitude of D-link-7dBi-H1-1020.nsi
0
345
330
315
300
285
270
255
240
225
210
195
180
165
150
135
120
105
90
75
60
45
30
15
-20 -10 0
dB
Far-field amplitude of D-link-7dBi-v-1020.nsi
Far-field amplitude of D-link-5dBi-H-1020.nsi
Far-field amplitude of D-link-5dBi-v-1020.nsi
0
345
330
315
300
285
270
255
240
225
210
195
180
165
150
135
120
105
90
75
60
45
30
15
-20 -10 0
dB
Far-field amplitude of D-link-7dBi-v-1020.nsi
0
345
330
315
300
285
270
255
240
225
210
195
180
165
150
135
120
105
90
75
60
45
30
15
-20 -10 0
dB
Far-field amplitude of D-link-5dBi-v-1020.nsi
ANT24-0700 / ANT24-0700C
0
345
330
315
300
285
270
255
240
225
210
195
180
165
150
135
120
105
90
75
60
45
30
15
-20 -10 0
dB
Far-field amplitude of D-link-7dBi-H1-1020.nsi
ANT24-0501C/ ANT24-0501
0
345
330
315
300
285
270
255
240
225
210
195
180
165
150
135
120
105
90
75
60
45
30
15
-20 -10 0
dB
Far-field amplitude of D-link-5dBi-H-1020.nsi

9
System Requirements
D-Link ANT24-0501C
Indoor Omni-Directional Antenna
Electrical specication
Physical Properties
Package Contents
-One ANT24-0501C 2.4GHz 5dBi indoor
omni-directional antenna with a RP-SMA
plug connector
-One RP SMA/ RP TNC adapter
-One registration card and company contact
guide
Frequency Range 2400~2500MHz
Impedance 50Ω Normal
VSWR 1.92 Max
Peak Gain 5dBi
Admitted Power 1 W
E-Plane 36 deg.
H-Plane 360 deg.
Connector Reverse SMA plug
Antenna Material ABS, ABS+PC
Operating Temp -20°C ~ +65°C
Storage Temp -30°C ~ +75°C
Color Antenna: Metallic gray and silver

10
ANT24-0700 Install GuideSystem Requirements
ANT24-Series
D-Link ANT24-0502
Indoor Omni Directional Antenna
Electrical Specification
Environmental & Mechanical Characteristics
Frequency range
2400 MHz - 2500 MHz
Gain
5.0dBi
VSWR
2.0 : 1 Max
Polarization
Linear, vertical
HPBW/horizontal
360°
HPBW/vertical
40°
Downtilt
0°
Power handling
2 W (cw)
Impedance
50 Ohms
Connector
RP SMA Plug
Temperature
-10C to +55C
Humidity
95% @5ˈ˖
Radome color
Black
Radome material
ABS, UV resistant
Weight
20 g
Dimensions
ӽ13.5 x 177 mm
H-plane Co-polarization Pattern
12
-9
-6
-3
0
3
6
0
30
60
90
120
150
180
210
240
270
300
330
12
-9
-6
-3
0
3
6
2400 MHz
2450 MHz
2500 MHz
V-plane Co-polarization Pattern
-24
-21
-18
-15
-12
-9
-6
-3
0
3
6
0
30
60
90
120
150
180
210
240
270
300
330
-24
-21
-18
-15
-12
-9
-6
-3
0
3
6
2400MHz
2450MHz
2500MHz
ANT24-Series
D-Link ANT24-0502
Indoor Omni-Directional Antenna

11
System Requirements
ANT24-Series
D-Link DWL-50AT
Indoor Omni-Directional Antenna
5.0dBi Typical
2.0:1 Max.
nominal
197 mm(length)
29.5gw
Electrical specication
0
345
330
315
300
285
270
255
240
225
210
195
180
165
150
135
120
105
90
75
60
45
30
15
-20 -10 0
dB
Far-field amplitude of C147-510017-A-V.nsi
2.4GHz 2.45GHz 2.5GHz
0
345
330
315
300
285
270
255
240
225
210
195
180
165
150
135
120
105
90
75
60
45
30
15
-20 -10 0
dB
Far-field amplitude of C147-510017-A-V.nsi
2.4GHz 2.45GHz 2.5GHz
0
345
330
315
300
285
270
255
240
225
210
195
180
165
150
135
120
105
90
75
60
45
30
15
-20 -10 0
dB
Far-field amplitude of C147-510017-A-H.nsi
2.4GHz 2.45GHz 2.5GHz

12
ANT24-0700 Install GuideSystem Requirements
D-Link ANT24-0600
Indoor Directional Antenna
Electrical specication
Physical Properties
Package Contents
-One ANT24-0600 2.4GHz indoor 6dBi directional
Antenna with 1.5 Filotex cable and RP-SMA Jack
connector
-One RP-SMA/ RP-TNC adaptor
-One User’s QIG
-Two Crews
-Two plastic xings
-One sticker
Frequency Range 2400~2500MHz
Impedance 50Ω Normal
VSWR 1.92 Max
Return Loss -10 dB Maximum
Antenna Structure Pateh antenna
Peak Gain ( w/o cable loss) 6.0 dBi @ 2.45GHz ( typical)
Admitted Power 1 W
Cable loss( 1.5m) 2.1dB@2.45GHz
E-Plane 68°
H-Plane 80°
Cable Filotex 50Ω
Antenna Cover ABS
Antenna Base PC
Operating Temp -20°C ~ +65°C
Storage Temp -30°C ~ +75°C
Color White
Desktop
Magnetic Attach
Wall Mounting
ANT24-Series

13
System Requirements
D-Link ANT24-0700
Indoor Omni-Directional Antenna
Electrical specication
Physical Properties
Frequency Range 2400~2500MHz
Impedance 50Ω Normal
VSWR 1.92 Max
Return Loss -10 dB Maximum
Antenna Structure Helis antenna
Peak Gain ( w/o cable loss) 7dBi
Admitted Power 1 W
Cable loss( 1.5m) 2.1dB@2.45GHz
E-Plane 24 deg.
H-Plane 360 deg.
Cable RG-178 50Ω
Cable length 1.5 M
Cable color Gray
Connector Reverse SMA plug
Antenna Material ABS, ABS+PC
Operating Temp -20°C ~ +65°C
Storage Temp -30°C ~ +75°C
Color Antenna: Metallic gray and silver
Base: Metallic gray
Package Contents
-D-Link ANT24-0700 2.4GHz Omni-Directional Indoor
Antenna
-SMA to TNC Adapter
-Magnetic Base with 1.5m Extension Cable
-Mounting Kit
-Installation Guide
ANT24-Series

14
ANT24-0700 Install GuideSystem Requirements
D-Link ANT24-0700C
Indoor Omni-Directional Antenna
Electrical specication
Physical Properties
Package Contents
-One ANT24-0700C 2.4GHz 7dBi indoor omnidirectional antenna with a RP-SMA plug connector
-One RP SMA/ RP TNC adapter
-One registration card and company contact guide
Frequency Range 2400~2500MHz
Impedance 50Ω Normal
VSWR 1.92 Max
Return Loss 10 dB Maximum
Antenna Structure Helis antenna
Peak Gain ( w/o cable loss) 7dBi
Admitted Power 1 W
Cable loss( 1.5m) 2.1dB@2.45GHz
E-Plane 24 deg.
H-Plane 360 deg.
Cable RG-178 50Ω
Cable length 1.5 M
Cable color Gray
Connector Reverse SMA plug
Antenna Material ABS, ABS+PC
Operating Temp -20°C ~ +65°C
Storage Temp -30°C ~ +75°C
Color Antenna: Metallic gray and silver
Base: Metallic gray

15
System Requirements
D-Link ANT24-0800 Indoor/Outdoor
Omni-Directional Antenna
Electrical specication
Environmental & Mechanical Characteristics
Mounting Configurations for pole/ wall
Omni-Directional Antenna for 802.11b/g
Pole(max φ=50mm)
2
3
1
4
When you install the antenna,
please try to find an open space like
the picture (1) , avoid to install like
the picture (2) cause the omni-directional
Picture (1)
90
o
180
o
150
o
120
o
60
o
30
o
0
o
-150
o
-90
o
-120
o
-60
o
-30
o
-3
-10
-20
-30
Horizontal
90
o
180
o
150
o
120
o
60
o
30
o
-150
o
-90
o
-120
o
-60
o
-30
o
-3
-10
-20
-30
Vertical
0
o
Mounting Configurations for pole/ wall
Omni-Directional Antenna for 802.11b/g
Pole(max φ=50mm)
Wall
2
3
1
4
1
5
6
1 Antenna body
2 M5-0.8 nut
3 M5 Washer
4 M5 U-Type Screw
5 Screw
6 Anchor
When you install the antenna,
please try to find an open space like
the picture (1) , avoid to install like
the picture (2) cause the omni-directional
signals might be blocked and performance
be affected.
Picture (1)
Picture (2)
Please always install the antenna
vertically to the horizontal surface, not
Picture (3)
1.Antenna body
2.M5-0.8 nut
3.M5 Washer
4.M5 U-Type Screw
5.Screw
6.Anchor
Ø19×520mm
340g without joint
(50cm)
ANT24-Series

16
ANT24-0700 Install GuideSystem Requirements
D-Link ANT24-0801
Indoor/Outdoor
Directional Panel Antenna
Electrical specication
Environmental & Mechanical Characteristics
Survival wind speed 216 km/hr
Temperature -40 C to +80 C
Humidity 95% @ 55 C
Lightning protection DC ground
Radome color Gray-white
Radome material ABS, UV resistant
Housing material AL6063
Weight 0.3 kgw
Dimensions 120 x 120 x 43 mm
Frequency 2400~2500MHz
Gain 8.5 dBi
VSWR 1.5 : 1 Max
Polarization Linear, vertical
HPBW / horizontal 65
HPBW / vertical 65
Front to back ratio 15 dB
Power handling 50 W (cm)
Impedance 50 Ohms
Connector N - female
65
°
ANT24-Series

17
System Requirements
D-Link ANT24-1200
Indoor Directional Panel Antenna
Electrical specication
Environmental & Mechanical Characteristics
Survival wind speed 180 km/hr
Temperature -10 C to +55 C
Humidity 95% @ 55 C
Lightning protection DC ground
Radome color White
Radome material ABS, UV resistant
Weight 19 kgw
Dimensions 330 x 93 x 20.7 mm
Frequency range 2400 MHz - 2500 MHz
Gain 12 dBi
VSWR 1.5 : 1 Max
Polarization Linear, vertical
HPBW / horizontal 80
HPBW / vertical 23
Front to back ratio 15 dB
Downtilt 0
Power handling 20 W(cm)
Impedance 50 Ohms
Connector SMA female
ANT24-Series

18
ANT24-0700 Install GuideSystem Requirements
D-Link ANT24-1201
Outdoor Directional Yagi Antenna
Electrical specication
Environmental & Mechanical Characteristics
Survival wind speed 216 km/hr
Temperature -40 C to +80 C
Humidity 95% @ 25 C
Lightning protection DC ground
Radome color Gray-White
Radome material ABS, UV resistant re retaedant
Weight 0.3 kgw
Dimensions 280 x 87x 48 mm
Frequency range 2400 MHz - 2500 MHz
Gain 12 dBi
VSWR 1.5 : 1 Max
Polarization Linear, vertical
HPBW / horizontal 50
HPBW / vertical 50
Front to back ratio 15 dB
Downtilt 0
Power handling 10 W (cm)
Impedance 50 Ohms
Connector N female
Cable UL 198; 32cm
50
ANT24-Series

19
System Requirements
ANT24-Series
D-Link ANT24-1202 Outdoor
Omni-Directional Antenna

20
ANT24-0700 Install GuideSystem Requirements
ANT24-Series
D-Link ANT24-1400
Outdoor Directional Panel Antenna
Electrical specication
Environmental & Mechanical Characteristics
Survival wind speed 216 km/hr
Temperature -40 C to +80 C
Humidity 100% @ 25 C
Lightning protection DC ground
Radome color Gray-White
Radome material ABS, UV resistant
Weight 0.825 kgw
Dimensions 240 x 240x 69.5 mm
Frequency range 2400 MHz - 2500 MHz
Gain 14 dBi
VSWR 1.5 : 1 Max
Polarization Linear, vertical
HPBW / horizontal 30
HPBW / vertical 30
Front to back ratio 15 dB
Downtilt 0
Power handling 10 W (cm)
Impedance 50 Ohms
Connector N female
Cable ULA198
Pole mounting
method 1.
Pole mounting
method 2.

21
System Requirements
ANT24-Series
D-Link ANT24-1800
Outdoor Directional Panel Antenna
Electrical specication
Environmental & Mechanical Characteristics
Survival wind speed 216 km/hr
Temperature -40 C to +80 C
Humidity 100% @ 25 C
Lightning protection DC ground
Radome color White
Radome material ABS, UV resistant
Housing material Galvanized Iron, Fire retardant
Weight 1.6 kgw
Dimensions 360 x 360x 16 mm
3
Frequency range 2400 MHz - 2500 MHz
Gain 18 dBi
VSWR 1.5 : 1 Max
Polarization Linear, vertical
HPBW / horizontal 15
HPBW / vertical 15
Front to back ratio 26 dB
Downtilt 0
Power handling 50 W (cm)
Impedance 50 Ohms
Connector N female

22
ANT24-0700 Install GuideSystem Requirements
ANT24-Series
D-Link ANT24-2100
Outdoor Directional Antenna

23
System Requirements
ANT70-Series
D-Link ANT70-0800
Dual-Band Omni-Directional Antenna
Electrical specication
Environmental & Mechanical Characteristics
Frequency Range 2400 MHz - 2500 MHz 4900 MHz - 5470
MHz
Gain 8 dBi 8 dBi
VSWR 2.0 : 1 Max.
HPBW / horizontal 360°
HPBW / vertical 15°
Polarization Linear, vertical
Power handling 5 W (cw)
Impedance 50 Ohms
Connector N Jack
Survival wind speed 216 km/hr
Temperature - 40°C to +70°C
Humidity 95% @ 55°C
Radome color Gray
Radome material ABS, UV resistant
Weight 350 g
Dimensions 80x78x870 mm
Package Contents
-D-Link ANT70-0800 Antenna
-Extension Cable(50cm)
-Surge Protector
-Mounting Kit
-Water-proof tape
-Quick Installation Guide
2.4 GHz:
5 GHz:
2.4 GHz:
5 GHz:
Mounting Configurations for pole/ wall
Omni-Directional Antenna for 802.11b/g
Pole(maxφ=50mm)
2
3
1
4
When you install the antenna,
please try to find an open space like
the picture (1) , avoid to install like
the picture (2) cause the omni-directional
Picture (1)
Mounting Configurations for pole/ wall
Omni-Directional Antenna for 802.11b/g
Pole(maxφ=50mm)
Wall
2
3
1
4
1
5
6
1 Antenna body
2 M5-0.8 nut
3 M5 Washer
4 M5 U-Type Screw
5 Screw
6 Anchor
When you install the antenna,
please try to find an open space like
the picture (1) , avoid to install like
the picture (2) cause the omni-directional
signals might be blocked and performance
be affected.
Picture (1)
Picture (2)
Please always install the antenna
vertically to the horizontal surface, not
recommended to mount it perpendicular
to the wall.
Picture (3)
1.Antenna body
2.M5-0.8 nut
3.M5 Washer
4.M5 U-Type Screw
5.Screw
6.Anchor

24
ANT24-0700 Install GuideSystem Requirements
ANT70-Series
D-Link ANT70-0801
Dual-Band Omni-Directional Antenna
Electrical specication
Environmental & Mechanical Characteristics
Frequency Range 2400 MHz - 2500 MHz 5400 MHz - 5875
MHz
Gain 8 dBi 8 dBi
VSWR 2.0 : 1 Max.
HPBW / horizontal 360°
HPBW / vertical 15°
Polarization Linear, vertical
Power handling 5 W (cw)
Impedance 50 Ohms
Connector N Jack
Survival wind speed 216 km/hr
Temperature - 40°C to +70°C
Humidity 95% @ 55°C
Radome color Gray
Radome material ABS, UV resistant
Weight 350 g
Dimensions 80x78x870 mm
Package Contents
-D-Link ANT70-0801 Antenna
-Extension Cable(50cm)
-Surge Protector
-Mounting Kit
-Water-proof tape
-Quick Installation Guide
Mounting Configurations for pole/ wall
Omni-Directional Antenna for 802.11b/g
Pole(maxφ=50mm)
2
3
1
4
When you install the antenna,
please try to find an open space like
the picture (1) , avoid to install like
the picture (2) cause the omni-directional
Picture (1)
Mounting Configurations for pole/ wall
Omni-Directional Antenna for 802.11b/g
Pole(maxφ=50mm)
Wall
2
3
1
4
1
5
6
1 Antenna body
2 M5-0.8 nut
3 M5 Washer
4 M5 U-Type Screw
5 Screw
6 Anchor
When you install the antenna,
please try to find an open space like
the picture (1) , avoid to install like
the picture (2) cause the omni-directional
signals might be blocked and performance
be affected.
Picture (1)
Picture (2)
Please always install the antenna
vertically to the horizontal surface, not
recommended to mount it perpendicular
to the wall.
Picture (3)
2.4 GHz:
5 GHz:
2.4 GHz:
5 GHz:
1.Antenna body
2.M5-0.8 nut
3.M5 Washer
4.M5 U-Type Screw
5.Screw
6.Anchor

25
System Requirements
ANT70-Series
D-Link ANT70-1000
Dual-Band Directional Panel Antenna
Electrical specication
Environmental & Mechanical Characteristics
Frequency Range 2400 MHz - 2500 MHz 4900 MHz - 5875
MHz
Gain 8.5 dBi 10.5 dBi
VSWR 2.0 : 1 Max. 2.0 : 1 Max.
HPBW / horizontal 58° 45°
HPBW / vertical 55° 45°
Polarization Linear, vertical
Power handling 5 W (cw)
Front to back ratio 15dB
Downtilt 0°
Impedance 50 Ohms
Connector N Jack
Survival wind speed 216 km/hr
Temperature - 40°C to +80°C
Humidity 95% @ 55°C
Radome color Gray
Radome material ABS, UV resistant
Weight 150 g
Dimensions 114 x124 x 40 mm
45
45
58
55
2.4 GHz:
5 GHz:
2.4 GHz:
5 GHz:
2.4 GHz:
5 GHz:
Package Contents
-D-Link ANT70-1000 Antenna
-Extension Cable(50cm)
-Surge Protector
-Mounting Kit
-Water-proof tape
-Quick Installation Guide

26
ANT24-0700 Install GuideSystem Requirements
ANT70-Series
D-Link ANT70-1800
Dual-Band Directional Panel Antenna
Electrical specication
Environmental & Mechanical Characteristics
Frequency Range 2400 MHz - 2500 MHz 4900 MHz - 5875
MHz
Gain 14 dBi 18 dBi
VSWR 2.0 : 1 Max. 2.0 : 1 Max.
HPBW / horizontal 30° 15°
HPBW / vertical 30° 15°
Polarization Linear, vertical
Power handling 10 W (cw)
Front to back ratio 15dB
Downtilt 0°
Impedance 50 Ohms
Connector N Jack
Survival wind speed 216 km/hr
Temperature - 40°C to +80°C
Humidity 95% @ 55°C
Radome color Light Gray
Radome material ABS, UV resistant
Weight 400 g
Dimensions 200 x218 x 50 mm
15
15
30
30
2.4 GHz:
5 GHz:
Package Contents
-D-Link ANT70-1800 Antenna
-Extension Cable(50cm)
-Surge Protector
-Mounting Kit
-Water-proof tape
-Quick Installation Guide
2.4 GHz:
5 GHz:
2.4 GHz:
5 GHz:

27
System Requirements
Fresnel Zone
Line-of-Sight (LOS)
Visual and RF Line-of-Sight ( LOS ) between the sending and receiving
antennas is essential in achieving long range in wireless communication
systems. There are two types of LOS that are generally used to describe an
environment:
Visual LOS is the ability to see from one site to the other. It requires only a
straight liner path between two points.
RF LOS requires not only visual LOS, but also a football-shaped path free of
obstacles for data to optimally travel from one point to another.
Fresnel Zone:
The Fresnel Zone can be thought of as a football-shaped tunnel between two
sites that provides a path for RF signals.
In order to achieve the greatest range, the football-shaped path in which radio
waves travel must be free of obstructions. Buildings, trees or any other
obstacles in the path will decrease the communication range. If the antennas
are mounted just barely off the ground, over half of the Fresnel zone ends up
being obstructed by the earth resulting in significant reduction in range. To
avoid this problem, the antenna should be mounted high enough off of the
ground so that the earth does not interfere with the central radius of the
Fresnel zone.

28
ANT24-0700 Install GuideSystem Requirements
Fresnel Zone
How far above the ground and other obstacles the antennas need to be is
determined by the radius of the Fresnel zone. The radius of the Fresnal Zone
depends upon the frequency and distance between the two radios. The
following table provides approximate Fresnel zone radius:
In order to have LOS clearance, the combined antenna height should be equal
to or at least 70% of the radius of the Fresnel zone.
Fresnel Zone Radius:
Range Distance between
antennas
Required Fresnel Zone
Radius ( 2.4GHz Radius)
Required Fresnel Zone
Radius ( 5GHz Radius)
300m 3.06m 2.12m
1.6Km 7.07m 4.9m
8Km 15.81m 10.95m
10Km 17.68m 12.25m
15Km 21.65m 15m
Required Fresnel
Zone radius

29
System Requirements
ANT24-Series
Model Name ANT24-0230 ANT24-0401 ANT24-0500 ANT24-0501 ANT24-0501C ANT24-0502 ANT24-0600
Frequency 2.4GHz 2.4GHz 2.4GHz 2.4GHz 2.4GHz 2.4GHz 2.4GHz
Signal directivity Omni-directional Omni-directional Omni-directional Omni-directional Omni-directional Omni-directional Directional Antenna
Application range Indoor Indoor ceiling only Indoor/ Outdoor Indoor only Indoor only Indoor Indoor only
Gain (Without cable loss) 1.8dBi 3.5dBi 5dBi 5dBi 5dBi 5dBi 6dBi
Approximate Range at 1 / 11/ 54Mbps
( Works with Indoor AP )
500m /400m /200m
/100m /5m**
250m/100m / 40 m 500m/ 250m/ 60m 500m/ 200m/ 50m 550m/ 250m/ 60m 500m/ 200m /60m 600m/ 350m /80m
Approximate Range at 1/ 11 /54Mbps
(Works with Outdoor AP)
--- --- 1.5Km/ 1.3Km/ 200m --- --- --- ---
Half Power Beam width H360 V70 H360 V120 H360 V32 H360 V36 H360 V36 H360 V40 H68 V80
Pigtail cable length 1.2 m --- 30cm 150cm --- --- 150cm
Antenna xed connector PR-SMA plug SMA jack N-jack RP-SMA plug RP-SMA plug RP-SMA plug RP-SMA plug
Surge protector for outdoors --- --- Optional --- --- --- ---
Default extension cable length --- 2M 3M --- --- --- ---
Default mounting conguration Desktop Ceiling Pole Wall / desktop/magnetic Attach to AP/Router Attach to AP/Router Wall/ desktop/magnetic
Optional accessories --- --- ANT24-SP --- --- --- ---
Optional antenna cable kits --- --- ANT24-CB series --- --- --- ---

30
ANT24-0700 Install GuideSystem Requirements
Model Name ANT24-0700 ANT24-0700C ANT24-0800 ANT24-0801 ANT24-1200 ANT24-1201
Frequency 2.4GHz 2.4GHz 2.4GHz 2.4GHz 2.4GHz 2.4GHz
Signal directivity Omni-directional Omni-directional Omni-directional Directional Directional
Application range Indoor only Indoor only Indoor/ Outdoor Indoor/ Outdoor Indoor only Outdoor
Gain (Without cable loss) 7dBi 7dBi 8dBi 8.5dBi 12dBi 12dBi
Approximate Range at 1 / 11/ 54Mbps
( Works with Indoor AP )
550m/ 250m/60m 600m/ 300m/ 70m 700m/ 350m/ 100m 800m/ 500m/ 150m 1.5Km / 1.2Km/ 500m ---
Approximate Range at 1/ 11 /54Mbps
(Works with Outdoor AP)
--- --- 2Km / 1Km/ 400m 2.5Km / 1.5Km/ 600m --- 3Km / 2.5Km/ 1Km
Half Power Beam width H360 V24 H360 V24 H360 V15 H70 V65 H80 V23 H50 V50
Pigtail cable length 150cm 150cm NA 30cm NA 30cm
Antenna xed connector RP-SMA plug RP-SMA plug N-jack N-jack SMA jack N-jack
Surge protector for outdoors --- --- Included Included --- Included
Default extension cable length --- --- 50cm 3M 3M 50cm
Default mounting conguration Wall/ desktop/magnetic Attach to AP/Router Pole Wall/ pole Window/ wall Wall/ pole
Optional accessories --- --- --- --- --- ---
Optional antenna cable kits
---
--- ANT24-CB series ANT24-CB series --- ANT24-CB series

31
System Requirements
Model Name ANT24-1202 ANT24-1400 ANT24-1800 ANT24-2100
Frequency 2.4GHz 2.4GHz 4.6GHz 2.4GHz
Signal directivity Omni-directional Directional Directional Directional
Application range Outdoor Outdoor Outdoor Outdoor
Gain (Without cable loss) 12dBi 14dBi 18dBi 21dBi
Approximate Range at 1 / 11/ 54Mbps
( Works with Indoor AP )
--- --- --- ---
Approximate Range at 1/ 11 /54Mbps
(Works with Outdoor AP)
3Km / 1.8Km/ 450m 6Km / 4.5Km/ 1Km 8Km / 6Km/ 1.5Km 8Km / 6Km/ 1.5Km
Half Power Beam width H360 V6 H30 V30 H15 V15 H10 V12
Pigtail cable length 30cm 30cm --- 31.5CM
Antenna xed connector N-jack N-jack N-jack N-jack
Surge protector for outdoors Included Included Included Included
Default extension cable length 50cm 50cm 50cm 50cm
Default mounting conguration Wall/ pole Wall/ pole Wall/ pole Pole
Optional accessories --- --- --- ---
Optional antenna cable kits ANT24-CB series ANT24-CB series ANT24-CB series ANT24-CB series

32
ANT24-0700 Install GuideSystem Requirements
Model Name ANT70-0800 ANT70-0801 ANT70-1000 ANT70-1800
Frequency 2.4GHz/ 5GHz 2.4GHz/ 5GHz 2.4GHz/ 5GHz 2.4GHz/ 5GHz
Signal directivity Omni-Directional Omni-Directional Directional Directional
Application range Indoor/ Outdoor Indoor/ Outdoor Indoor/ Outdoor Outdoor
Gain (Without cable loss)
2.4GHz: 8dBi
5GHz: 8dBi
2.4GHz: 8dBi
5GHz: 8dBi
2.4GHz: 8dBi
5GHz: 10dBi
2.4GHz: 14Bi
5GHz: 18dBi
Approximate Range at 1 / 11/ 54Mbps
( Works with Indoor AP )
2.4GHz: 700m/ 350m/ 100m
5GHZ: 1K/ 500m/ 200m
2.4GHz: 700m/ 350m/ 100m
5GHZ: 1K/ 500m/ 200m
2.4GHz: 800m/ 400m/ 150m
5GHZ: 1.2K/ 600m/ 250m
---
Approximate Range at 1/ 11 /54Mbps
(Works with Outdoor AP)
2.4GHz: 800m/ 450m/ 150m
5GHZ: 1K/ 500m/ 200m
2.4GHz: 800m/ 450m/ 150m
5GHZ: 1K/ 500m/ 200m
2.4GHz: 1K/ 500m/ 200m
5GHZ: 1.5K/ 700m/ 300m
2.4GHz: 6K/ 4.5m/ 1Km
5GHZ: 8Km/ 5Km/ 1.5Km
Half Power Beam width
2.4GHz: H360 V15
5GHz: H360 V15
2.4GHz: H360 V15
5GHz: H360 V15
2.4GHz: H58 V55
5GHz: H45 V45
2.4GHz: H30 V30
5GHz: H15 V15
Pigtail cable length NA NA NA NA
Antenna xed connector N-jack N-jack N-jack N-jack
Surge protector for outdoors Included Included Included Included
Default extension cable length 50cm 50cm 50cm 50cm
Default mounting conguration Pole Pole Pole Pole
Optional accessories --- --- --- ---
Optional antenna cable kits ANT24-CB series ANT24-CB series ANT24-CB series ANT24-CB series
NOTE:
*1.Extended range reference based on RF-Output Power 16dbm( Indoor AP), 23 ( outdoor AP) with default cable loss,
*2.The transmission distance range might depend on the two same spec antennas with default cable loss under free line-of –sight environment.
*3. Effective range based on EIRP( Effected Isotropic Radiation Power. = device output power + antenna gain – cable lost )
**BW: Beam Width. H : horizontal plane pattern, V : vertical plane pattern
The actual range will be effected by users’ physical environment. The above gures are reference.

ͿΝΦΘ
RP Ϳ-Jack
ͿͻΒΔΜ
ͿΝΦΘ
΄;ͲΝΦΘ ΄;ͲͻΒΔΜ͵ͽΚΟΜͲΠΦΥΖΣ
CONNECTORS OUTLOOK
΅ͿʹΝΦΘ