D Link 5212G User Manual

IEEE 802.11g (draft)

Wireless Network Adapter

User Manual

Model: GL245401-0A

GL2454MP-0A

version 1.0

Manufacturer's Disclaimer Statement

The information in this document is subject to change without notice and does not

represent a commitment on the part of the vendor. No warranty or representation,

either expressed or implied, is made with respect to the quality, accuracy or fitness for

any particular purpose of this document. The manufacturer reserves the right to

make changes to the content of this document and/or the products associated with it at

any time without obligation to notify any person or organization of such changes. In

no event will the manufacturer be liable for direct, indirect, special, incidental or

consequential damages arising out of the use or inability to use this product or

documentation, even if advised of the possibility of such damages. This document

contains materials protected by copyright. All rights are reserved. No part of this

manual may be reproduced or transmitted in any form, by any means or for any

purpose without expressed written consent of its authors. Product names appearing

in this document are mentioned for identification purchases only. All trademarks,

product names or brand names appearing in this document are registered property of

their respective owners.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one of the

following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by

the party responsible for compliance could void the user's authority to

operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated

with minimum distance 20cm between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any

other antenna or transmitter.

This device is intended only for OEM integrators under the following

conditions:

1) The antenna must be installed such that 20 cm is maintained between the

antenna and users, and

2) The transmitter module may not be co-located with any other transmitter or

antenna.

As long as 2 conditions above are met, further transmitter test will not be

required. However, the OEM integrator is still responsible for testing their end-

product for any additional compliance requirements required with this module

installed (for example, digital device emissions, PC peripheral requirements,

etc.).

IMPORTANT NOTE: In the event that these conditions can not be met (for

example certain laptop configurations or co-location with another transmitter),

then the FCC authorization is no longer considered valid and the FCC ID can

not be used on the final product. In these circumstances, the OEM integrator

will be responsible for re-evaluating the end product (including the transmitter)

and obtaining a separate FCC authorization.

End Product Labeling

This transmitter module is authorized only for use in device where the antenna

may be installed such that 20 cm may be maintained between the antenna

and users (for example RT, AP & PCI Card). The final end product must be

labeled in a visible area with the following: “Contains TX FCC ID: KA25212G”.

Manual Information That Must be Included

The OEM integrator has to be aware not to provide information to the end user

regarding how to install or remove this RF module in the users manual of the

end product which integrate this module

The users manual for OEM integrators must include the following information

in a prominent location “ IMPORTANT NOTE: To comply with FCC RF

exposure compliance requirements, the antenna used for this transmitter must

be installed to provide a separation distance of at least 20 cm from all persons

and must not be co-located or operating in conjunction with any other antenna

or transmitter.

Driver Installation

Step 1: Insert the 802.11g Wireless Network Adapter into your computer.

Windows Found New Hardware Wizard will come up.

Select the second option and click “Next” to continue.