dji NAZA-F45 Assembling And Parameters Setup

ASSEMBLING AND PARAMETERS SETUP FOR QUADCOPTER (DJI NAZA-F450 )
USING TRANSMITTER (FUTABA T10 J) AND RECEIVER (R3008SB)
MARCH 13, 2017
UNIVERSITÄT BREMEN
www.pcessflight.com
1
Contents
CHAPTER 1 ............................................................................................................................................... 2
ASSEMBLY & CONNECTIONS ............................................................................................................... 2
PORT Description ............................................................................................................................. 2
Hardware Connections .................................................................................................................... 3
Esc Configuration We Used ............................................................................................................. 3
Main Controller(MC) Mount ........................................................................................................... 3
Power Management Unit (PMU) Module Mount ........................................................................... 3
GPS/Compass Mount (Optional) ..................................................................................................... 3
Transmitter(TX) & Receiver(RX) Connections ................................................................................. 4
CHAPTER 2 ............................................................................................................................................... 5
LINKING OF RECIEVER AND TRANSMITTER ......................................................................................... 5
10J Transmitter Specifications......................................................................................................... 5
R3008SB 2.4GHz T-FHSS 8-Channel Receiver .................................................................................. 7
LINKING OF RECIEVER AND TRANSMITTER ..................................................................................... 7
TRANSMITTER CONFIGURATION SETTINGS ........................................................................................ 7
CHAPTER 3 ............................................................................................................................................. 11
ASSISTANT SOFTWARE INSTALLATION AND CONFIGURATION ......................................................... 11
SOFTWARE AND DRIVER INSTALLATION ....................................................................................... 11
CONFIGURATION BY ASSISTANT ON A PC ..................................................................................... 12
CHAPTER 4 ............................................................................................................................................. 13
BASIC FLYING ..................................................................................................................................... 13
CONTROL MODE KNOWLEDGE ...................................................................................................... 13
START & STOP MOTOR KNOWLEDGE ............................................................................................ 13
COMPASS CALIBRATION ................................................................................................................ 14
ASSEMBLY CHECKING LIST ............................................................................................................. 15
LED DESCRIPTION .......................................................................................................................... 16
www.pcessflight.com
2
CHAPTER 1
ASSEMBLY & CONNECTIONS
PORT Description
Following is the brief description about the Main controller, Power Management Unit, GPS Module, LED Module, Servo Cable, Micro-USB Cable
www.pcessflight.com
3
Hardware Connections
The direction of the arrow in diagram indicates the rotation direction of the motor/propeller.
Esc Configuration We Used
We used Quad Rotor X Configuration in our case that is on 2nd place in the above picture. And Motor1 (M1) is Connected to M1 input on the controller and same procedure is followed for the rest of three Motors.
Main Controller(MC) Mount
(1) The DJI logo should face the sky, DO NOT mount the MC upside-down. (2) The MC sides should be parallel to the aircraft body. (3) The arrow should point to the nose direction of aircraft. (4) The MC is best positioned near the aircraft’s center of gravity. Make sure all ports are accessible.
Tip It is recommended to fix the MC until all wirings and configurations are completed, using 3M gummed paper provided to fix the MC.
Power Management Unit (PMU) Module Mount
DO NOT attach the PMU on other device. Sufficient air flow over the PMU is highly recommended. TipIf use with DJI multi-rotor, you can solder the power cable to power pads on frame bottom board. Please refer to DJI multi-rotor manual for details. If use with 3rd part aircraft, you can make a connecter
by yourself to connect PMU and battery.
GPS/Compass Mount (Optional)
GPS/Compass is sensitive to magnetic interference, should be far away from any electronic devices. If you use your own mounting rod, make sure it is NOT magnetic!
Procedures
(1) You should use epoxy resin AB glue to assemble the GPS bracket first. Mount the bracket on
the center plate of craft. Position the bracket at least 10 cm from any propeller.
(2) The DJI logo marked on the GPS should face the sky, with the orientation arrow pointing
directly forward. then fix the GPS on the plate of the bracket (by 3M glue provided).
www.pcessflight.com
4
TipThe GPS/Compass is packaged with a special indication line for mounting for the first time.
Transmitter(TX) & Receiver(RX) Connections
(1) Refer to you TX Manual, setup the Aileron, Elevator, Throttle, Rudder channels on your TX first, and choose a 3- position switch as control mode switch.
(2) Attach the matched RX to aircraft, then connect your RX to the right ports on MC. The following diagram shows the connection example for traditional RX.
Step3 Double Check: In this step, turn on the transmitter, connect the battery to the PMU, and then watch the LED, if you can
see the LED blinks the system is working.
www.pcessflight.com
5
CHAPTER 2
LINKING OF RECIEVER AND TRANSMITTER
10J Transmitter Specifications
Type: 2-stick, 10-channel T-FHSS / S-FHSS / FHSS selectable Current Drain: 140mA
System features
Futaba T-FHSS, S-FHSS 2.4GHz security Airplane, heli, glider and multi-rotor software 30-model memory S. Bus capable T-FHSS receiver Telemetry Synthesized voice for telemetry data Vibration alerts for alarm conditions and low battery User-updatable software (requires optional CIU-2 interface) Wireless data transfer among 10J transmitters Built-in S. Bus programming link for S. Bus servos 10-character model and user naming Large (128 x 64 dot) backlit LCD display Built-in diversity antenna Jog dial and 3 buttons for fast, easy programming Sub-trim and fail-safe (all channels) Trim step adjustability Trainer system Throttle cut 2 count-up/-down timers + integrated timer Model timer Range check mode 10 channels (one variable knob, five 2-position switches, two 3-position switches, one Servo reversing, endpoint adjustment, digital trims, dual rates/exponential* & ATL momentary switch, two digital levers) Servo cycle w/bar graph displays Assignable switch/lever/functions (Ch. 5-10)
Here are just some of the functions you'll find on the 10J:
The large backlit LCD display helps make programming easy, as well as clearly showing the timers and telemetry data.
Aeroplane mode
+ 11 hidden pages