Page 1
OWNER'S
MANUAL
Operating and Servicing
Instructions
Please read these
instructions carefully before
using your Platinum ForceTM Upright.
Let us help you put your
cleaner together or answer
any questions, call:
1-800-321
:I
134
(USA & Canada
www.dirtdev.iI.com
For quick reference, please record your vacuum
information below.
Mod'el
Mfg. Code:
(Mfg.
#:
code located on the lower backside of cleaner)
A
WARNING:
Cleaner assembly may include small parts.
Small parts can present a choking hazard.
spafiol - pagina
El
02001
All
rights reserved # 1-1 13048-000
Rev. 11/01
/
Page 2
CONGRATULATIONS
You are now the proud owner of a Dirt DeviF Platinum Force" Upright. You'll never buy anoth-
er bag again with the unique bagless design that includes a see-through dirt container for retrieving lost items. And now you'll never buy another belt again with a new permanent belt system that
never needs changed. You'll also enjoy superior cleaning performance with
Vacuum Power and an exclusive airpath for ultimate suction.
'12
amps of Maximum
Allergen sufferers will benefit with the exclusive PERMA FILTERm with
located inside the dirt cup and HEPA exhaust filter that prevent over
CleanStreamm
99.97%
of dust and aller-
Filtration
gens from escaping the vacuum and re-entering the room. Other features are included that make
vacuuming easier such as the Swivel Casters" for easy maneuvering, ready-to-use tools-on-board
for above floor cleaning and
handlfoot controls to reduce bending.
We are very proud of our products and hope that you are equally satisfied with their quality and
performance.
Thank you for your support of Dirt Devilm products.
Visit our website at www.dirtdevil.com
TABLE OF CONTENTS
Feature Descriptions
How To Assemble
How To Operate
Tool Storage ................................... .Page
Bare FloorICarpet Cleaning
Above Floor Cleaning
Carpet Settings ................................. .Page
*Dirt Sensor
Dirt Container & PERMA FILTERa with
Removal and Replacement
HEPA Filter Removal and Replacement.
Belt Removal and Replacement
Lightbulb Removal and Replacement
Troubleshooting Guide
...................................
....................................
......................................
........................
............................
...................................
~leanStream'"~.'Filtration
.............................
..........
...........................
.,
.........
......................
.................................
.Page
.Page
.Page
.Page
.Page
.Page
.Page
.Page
.Page
.Page
.Page 8
4
4
5
5
5
5
5
6
6
7
7
7
*Not Available on all models
LIMITED WARRANTY
To the consumer, Royal Appliance Mfg. Go. warrants this vacuum cleaner to be free of defectsin material or.workmanship commencing upon the date of the original
purchase. Refer to your vacuum cleaner carton for the length of warranty and save your orlgmal sales recelpt to validate start of warranty period.
If the vacuum cleaner should become defective within the warranty period, we will repair or replace an defective parts free of charge. The complete machine must
be delivered
inal sales receipt and your name,.address and telephone number. If you are not near a Warranty Statlon, call the factory for assistance in the USA
1-800-321-1134. Use only genuine Royal" replacement parts.
The warranty does not include unusual wear, damage resulting from accident or unreasonable use of the vacuum cleaner. This warranty does not cover brushes, bags,
flat belts, filters, bulbs or fan damage. This warranty does not cover unauthorized repairs. This warranty gives you specific legal rights and you may also have other
rights. (Other rights may vary from state to state in the USA).
Ill
.u@&i
to any ROYALm Authorized Sales & Warranty Service Station. Please include cornpike description of the problem, day of purchase, copy of orig-
&
CANADA:
Page 3
THIS CLEANER IS INTENDED FOR HOUSEHOLD USE ONLY
IMPORTANT SAFETY INSTRUCTIONS
When
you
use
an appliance,
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.
ALWAYS FOLLOW THESE SAFETY INSTRUCTIONS.
BRING CLEANER TO UPRIGHT POSITION WHEN USING THE HOSE AND ATTACHMENTS.
DO NOT LEAVE CLEANER UNATTENDED WHEN PLUGGED IN.
REGULARLY CHECK THE FILTERS TO CLEAN OR REPLACE.
WARNING: DO NOT USE SHARP OBJECTS TO CLEAN OUT THE HOSE SINCE THEY COULD CAUSE DAMAGE.
basic
precautions
should
be
followed,
including
the following:
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.
WARNING: TO REDUCE THE RISK
OF
FIRE,
ELECTRIC SHOCK OR INJURY:
Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing.
Do not use outdoors or on wet surfaces. Electrical shock could occur.
Do not allow to be used as a toy. Close attention is necessary when used by or near children.
Use only as described in this manual. Use only manufacturer's recommended attachments.
Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors,
or dropped into water, return it to a service center for inspection. Call 1-800-321-1134 for the nearest service center.
Do not pull or carry by cord, use cord as handle, close a door on cord, or pull cord around sharp edges or corners. Do
not run appliance over cord. Keep cord away from heated surfaces.
Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
Do not handle plug or appliance with wet hands.
Do not put any objects into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that
may reduce air flow.
Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
Do not use without dirt container and filters in place.
Turn off all controls before unplugging.
Use extra care when cleaning on stairs.
Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be present.
Keep the vacuum cleaner on the floor. Only the hand-held vacuum cleaners may
Cleaner must be in the upright position to lift the rotating brush off the carpet when doing above floor cleaning.
Do not use an extension cord with this vacuum cleaner.
Store the vacuum cleaner indoors. Put the vacuum cleaner away after use to prevent tripping accidents.
Using improper voltage may result in damage to the motor and possible injuiy to the user. Proper voltage is listed on the
cleaner date.
dl
set on furniture.
I
,
SAVE
I
To reduce the risk of electric shock, this appliance has a polarized plug (one blade wider than the other). This plug will
fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug.
tact a qualified electrician to install the proper outlet. Do not change the plug in any way.
THESE
WARNING:
INSTRUCTIONS
If
it still does not fit, con-
Page 4
Fia.
1
1. OnIOff Switch
2. Brushroll OnIOff Switch
3. Dirt Container
4. PERMA FILTER" with CleanStreamN
Filtration in Dirt Container
5. HEPA Filter
6. *Dirt Sensor
7.
Brushroll
8.
Clearview Brush Window
9. Scuff Guard" Bumper
10.
Ultra Edger
11. Height Adjust Window
12. Dual Headlights
13. Carry Handle
*Not available on all models
TOOL REQUIRED: PHILLIPS SCREWDRIVER
Fiu.
2
14. Crevice Tool
15. Cord Guide
16. Extension Wand
17.
Dusting Brush
18. Dirt Cup Release Latch
19. Extra Long Power Cord
20. Height Adjust Pedal
21. Swivel Casters"
22. Handle Release Pedal
23. Quick Cord Release
24. Upholstery Tool
25. Stretch Hose
Twist cord and insert up into han-
CAUTION:,
dle.
ING CORD WHILE INSERTING
INTO HANDLE.
AVOID PINCH-
P.ush upper handle onto upright,
aligning upper handle with
handle opening.
Insert the ONE screw into hole
located on the back of the handle. Insert the plastic handle fastener into the front of the handle.
Hold the handle fastener in place
when tightening.
4
Page 5
Plug cord into electrical outlet.
Turn Quick Cord Release
for easy cord removal.
Store cord in cord guide
(see Features
keep out of way while in use.
-
pg.
4)
to
Turn cleaner "onn. Switch located on the top of handle.
Release handle by depressing
pedal.
NOTE:
always be off when the handle
is in the upright position.
The brushroll will dle when lifting vacuum to
Use the convenient carry han-
transport.
BARE FLOOR CLEANING-
TURN BRUSHROLL OFF.
BARE FLOOR CLEANING
TURN BRUSHROLL OFF.
Turn the brushroll onloff switch
to the "off" position. This is
green switch located on the top
of the handle.
-
A~CHMENT USAGE
CARPET CLEANING-
TURN BRUSHROLL ON.
I
CARPET CLEANING -TURN BRUSHROLL ON.
As you switch to different carpet piles, depress the floor settings pedal until
the desired height is selected. Using the height adust window (located on
the nozzle) to view height adjust setting.
become jammed with an obstruction, turn the brushroll odoff switch to the
"off" position, then turn the unit off and unplug. Remove the obstruction.
Plug unit back in, turn the power on and the brushroll on.
NOTE:
Should the brushroll
I.
I
I
I
ULTRA EDGER
Flip the ultra edger (located on
the right side of the nozzle) so
the edge bristles face down.
The edge bristles provide effective baseboard cleaning. Return
to stored position for normal
vacuuming.
I
Remove the hose from the
side of the cleaner using the
finger loop to lift out of storage
position.
The crevice tool and extension
wand are located on the
the upper handle. To remove,
grasp tool at the top and pull out.
baa of
Pull crevice tool out of extension
wand. Use extension wand and
crevice tool together or
NOTE:
ly.
tool while in extension wand.
DO
NOT
separate-
use crevice
To remove tool,
Push the tool firmly on to the end
of the hose. If additional length is
needed, use the extension wand.
lift
up gently.
1
Page 6
The *Dirt Sensor system uses optics to detect existing dirt. A
red light illuminates when dirt is detected and turns off when
your carpet is clean.
DlRT DETECTION, MAKE SURE CLEANER IS ON PROPER HEIGHT ADJUSTMENT SETTING.
may cause sensor light to illuminate for long periods of time
due to the over abundance of small carpet fibers. The sensor
will continue to detect these new carpet fibers until they are
gone, which may take many passes with the cleaner.
IMPORTANT:
TO ENSURE OPTIMUM
NOTE:
New carpet
*Not available
CLEANING DIRT CONTAINER & PERMA FILTERa WITH
A
removable filter is located inside the dirt container. The filter does not need to
on
all models
CLEANSTREAM"
be
replaced
but
should be cleaned regularly for maximum
FILTRATION:
performance.
-
WARNING: TO REDUCE THE RISK OF INJURY FROM MOVING PARTS
Depress latch to raise the tool
caddy lid. The lid will automatically raise up. tion (see instructions below). tube should be aligned with the hose hole
Pull dirt container up and out
of nested position.
Remove and clean
TER with CleanStreamW filtra-
Empty the dirt containers con-
tents into
Ifdirtcontaineris washed-
THOROUGHLY
to unit.
UNPLUG BEFORE SERVICING.
a
wastebasket.
before returning
PERMA FIL- RETURN DlRT CONTAINER: Place dirt
NOTE:
DRY
container into nested position. The dirt cup
opening. Push the metal latch up against the
dirt container and then press the tool caddy
down. The caddy will lock into place.
I
-
Remove dirt container lid by
pulling up.
I
While holding the dirt container, grasp top of
filter, twist and firmly pull filter up and out.
*Regular ~aintenance: Each time the dirt container is
emptied, the filter should be cleaned. Tap the filter firmly
against the inside of a trash can until dirt stops falling from
the filter. (Filter will be discolored after use, this will not
affect the filter's performance.) TIP:
Use a soft brush
the dusting brush provided to help brush dirt out of filter.
NOTE:
DO
NOT
scrub the filter.
Replace the PERMA FILTERewith CleanStreamm Filtration:
Return filter to dirt container. Push filter into place to prevent
dirt leakage. Return dirt cup and lid to cleaner.
*
The cleaning instructions may vary depending on the dirt con-
ditions. In some cases. more or less cleanina of the PERMA
'
FILTER" with
~lean~tream"
Filtration may bYe required.
or
Page 7
For additional filtration, a
HEPA
media exhaust filter
is
located below the dirt cup. For best performance, replace filter yearly.
TOOL REQUIRED: PHILLIPS SCREWDRIVER
HEPA filter part # 3-860057-000, is located below the dirt container.
Unplug cleaner before changing filte~
NOTE:
NOTE:
For best performance, replace filter
yea*
For HEPA filter replacements call
1-800-321 -1 134
(USA & Canada).
Remove dirt container. To
remove the filter cover lid,
use
a
Phillips screwdriver
to
remove the
(1)
screw.
Pull lid up and away from
cleaner. and pull up and out.
Grasp HEPA filter cartridge
IMPORTANT: DO NOT
clean.To replace: Insert
HEPA filter into housing.
and
Replace screw
cover.
filter
This vacuum contains a permanent belt. If you experience problems with this unit, please call
-1
1-800-321
134 (USA & Canada) to locate the nearest Service Center.
1.
TOOL REQUIRED: PHILLIPS SCREWDRIVER
WARNING: TO REDUCE THE RISK
NOTE:
This cleaner uses a common automotive lamp
OF
ELECTRIC SHOCK - UNPLUG CLEANER BEFORE REMOVING OR REPLACING LIGHTBULB.
N06,
13.0
volts.
Lean cleaner back. Use a
Phillips screwdriver to
unscrew the two screws
located on each side of the
lens.
Pull bulb out of socket to
remove. Do not twist. Push
bulb into socket to replace.
Screw headlight lens back
into place.
To purchase replacement
1-800-321 -1
134
(USA & Canada).
bulbs,
call
Page 8
Cleaner won't run
EDUCE RISK OF PERSONAL INJURY - UNP
Possible Reasons
1.
Power cord not firmly plugged into outlet.
2.
Blown fuse or tripped breaker.
3. Needs service.
1. Dirt container not installed correctly.
2.
Dirt container full.
3. Brushroll worn.
4.
Broken belt.
5.
Clogged PERMA FILTERa.
6.
Dirty HEPA filter.
7.
Clear nozzle dirt passage hose clogged.
8.
Carpet height setting is incorrect.
9.
Lower hose inlet clogged.
10. Brushroll turned off.
G
CLEANER BEFORE SERVICING
Possible Solutions
1. Plug cord in firmly.
2.
Check fuse or breaker in home. Replace fuselresc
breaker.
3. Take to service center or call 1-800-321 -1 134.
1. Review
2. Empty dirt container - Pg.
3. Take to servicecenter or call 1-800-321-1 134.
4. Take to service center or call 1-800-321-1 134.
5.
6.
7.
8.
9.
10. Turn brushroll on
dirt
container
Remove PERMA FILTERa and clean - Pg.
Replace HEPA filter - Pg.
Remove dirt cup; inspect hose; remove obstructior
Set carpet height adjustment to appropriate
setting for carpet being cleaned
Remove dirt cup and clean inlet.
removal
-
Pg.
and
6.
7.
5.
replacement - Pg.
-
Pg.
I
6.
5.
Dust escaping from cleaner
Cleaner tools won't pick up
r
Headlight not working
l------
Cleaner is difficult to push
l------
Brushroll not rotating
*Sensor light will not turn
onloff
1. Dirt container full.
2. Dirt codainer not installed correctly.
1. Attachment hose clogged.
2. Dirt container full.
3. Filter clogged.
1. Bulb burnt out.
2.
Loose electrical wires.
1. Carpet height setting is incorrect.
2. Brushroll onloff switch is turned "off".
1.
Brushroll onloff switch is turned off.
2. Broken belt.
3. Brushroll jammed with an obstruction.
1. Needs service.
1. Height adjust setting is too low.
2. Cleaner needs service.
1. Empty dirt container - Pg.
2.
Review
dirt
contziner
1. Remove dirt cup; inspect hose; remove obstruction.
If necessary, remove 2 screws to remove attach
ment hose and clear obstruction
2. Empty dirt container - Pg.
3. Clean filter - Pg.
1. Replace bulb - Pg.
2.
Call 1-800-321-1 134 for nearest authorized
Royala Dealer.
1. Set carpet height adjustment to appropriate
setting for carpet being cleaned
2. Turn brushroll onloff switch to the "on" position.
1. Turn brushroll on/off switch to the
2. Take to Service Center or call 1-800-321-1134.
3. Turn the brushroll onloff switch to the "off" position. Turn the unit off and unplug. Remove the
obstruction. Plug unit back into outlet and turn the
power and brushroll switches to the "on" position.
1 ..'~ake to service center or call 1-800-321-1 134.
1. Set height adjust to proper setting
2. ,Call customer service at 1-800-321 -1 134.
6.
wmwal
7.
6.
and
replacement - Pg.
-
Pg.
6.
-
Pg.
on
-
5.
5.
position.
Pg.
5.
f
*Not available on all models
L
ANY OTHER SERVICING SHOULD BE DONE BY AN AUTHORIZED SERVICE REPRESENTATIVE
In the event that further assistance is required, see yourYellow Pages for an authorized Royala Dealer. Costs of any transportation to and
CUSTOMER SERVICE
from any place of repair are to be paid by the owner. The service parts used in this unit are easily replaced and readily available from an
authorized Royal" Dealer or retailer. Always identify your cleaner by the model number and manufacturing code when requesting informa-
tion or ordering replacement parts. (The model number appears on the back of the cleaner.)
(1 -800-321 -1 134)
Loading...