Digital Projection HIGHlite Cine 260 HB, HIGHlite Cine 260 HC, HIGHlite 1080p 330 User Manual
Page 1
Rev D July 2014
HIGHlite Cine 260 HB, HC
HIGHlite 1080p 330
High Brightness Digital Video Projector
16:9 widescreen display
User Manual
111-367D
Page 2
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Page 3
Rev D July 2014 Page iii
Please read this user manual carefully before using the projector, and keep
the manual handy for future reference.
A serial number is located on the back of the projector. Record it here:
Symbols used in this guide
Warnings
ELECTRICAL WARNING: this symbol indicates that there is a danger of
electrical shock unless the instructions are closely followed.
WARNING: this symbol indicates that there is a danger of physical
injury to yourself and/or damage to the equipment unless the
instructions are closely followed.
NOTE: this symbol indicates that there is some important information that
you should read.
Trademarks
• IBM is a registered trademark of International Business Machines Corporation.
• Macintosh and PowerBook are registered trademarks of Apple Computer, Inc.
• Other product and company names mentioned in this user’s manual may be the
trademarks of their respective holders.
Product revision
• Because we at Digital Projection continually strive to improve our products, we
may change specications and designs, and add new features without prior
notice. Projectors built prior to this revision of the User Manual may therefore not
include all the features described.
Manual revision
Date Description Revision
December 2010 Rev A
July 2011 addition of 1080p 330 Rev B
July 2012 brightness info corrected in spec
Declaration of Conformity removed
Rev C
July 2014 Product CD part number replaced. Rev D
Important Information
Page 4
Page iv Rev D July 2014
Important Information Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
General precautions
Do not open the cabinet. There are no user serviceable parts inside.
Use only the power cable provided.
Ensure that the power outlet includes a Ground connection, as this
equipment MUST be earthed.
Take care to prevent small objects such as paper or wire from falling
into the projector. If this does happen, switch off immediately, and have
the objects removed by authorised service personnel.
Do not expose the projector to rain or moisture, and do not place any
liquids on top of the projector.
Unplug before cleaning, and use a damp, not wet, cloth.
Do not touch the power plug with wet hands.
Do not touch the power plug during a thunder storm.
Handle the power cable carefully and avoid sharp bends. Do not use a
damaged power cable.
There are no user-serviceable parts inside the lamp module. The whole
module should be replaced.
Only lamps supplied by Digital Projection and intended for this
projector should be used. Fitting any other lamp could damage both
projector and lamp, and will invalidate the warranty.
Take care when removing the lamp module.
NEVERtouchthelamporreector.
Take care not to touch the glass surface of the lamp module. If you
do accidentally touch the glass, it should be cleaned before use. (see
section 5. Maintenance.)
Do not use the lamp for more than 2000 hours, as this may cause
serious lamp failure, damage the lamp module and cause extra cost on
replacement.
HID lamps produce high intensity light. Do not look directly at the light
coming from the lamp housing, or the lens, or allow items such as
magnifying lenses to be placed in the light path. This could result in
serious eye damage.
Do not touch the ventilation outlets, as they will become hot in use.
Do not cover or obstruct the ventilation outlets or inlets.
Do not cover the lens whilst the projector is switched on. This could
causeare
Always allow the projector to cool for 5 minutes before disconnecting
the power, moving the projector, changing the lamp or cleaning the
fansorlter.
Never use strong detergents or solvents such as alcohol or thinners to
clean the projector and lens.
Notes
Page 5
Rev D July 2014 Page v
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual Important Information
Installation precautions
Theprojectormustbeinstalledonlybysuitablyqualiedpersonnel,in
accordance with local building codes.
The projector should be installed as close to the power outlet as
possible.
The power connection should be easily accessible, so that it can be
disconnected in an emergency.
Ensure that there is at least 30cm (12in) of space between the
ventilation outlets and any wall, and 10cm (4in) on all other sides.
Do not install the projector close to anything that might be affected by
its operational heat, for instance, polystyrene ceiling tiles, curtains etc.
The projector weighs approximately 20 kg (44 lbs). Use safe handling
techniques when lifting the projector.
Do not stack more than three projectors.
When stacking projectors, the stack MUST be vertical, to ensure that
the stresses are distributed to all four chassis corners.
Before installation, make sure that the surface, ceiling or rigging that is
to support the projector is capable of supporting the combined weight
of all the projectors.
Backup safety chains or wires should always be used with ceiling
mount installations.
Do not place heavy objects on top of the projector chassis. Only the
chassis corners are capable of withstanding the weight of another
projector.
Do not drop or knock the projector.
Place the projector in a dry area away from sources of dust, moisture,
steam, smoke, sunlight or heat.
Do not tilt the projector more than ±8.5° forwards and backwards
when in use, as this may cause serious lamp failure, damage the lamp
module and cause extra cost on replacement. The projector my be
tilted left and right as necessary.
Operationandcongurationprecautions
Software update should NOT be carried out except by, or with the
supervision of, Digital Projection Service personnel.
Notes
±8.5°
±8.5°
Page 6
Page vi Rev D July 2014
Important Information Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Notes
Compliance with international standards
Noise
GSGV Acoustic Noise Information Ordinance
The sound pressure level is less than 35 dB (A) according to ISO 3744 or ISO 7779.
RF Interference
FCC
The Federal Communications Commission does not allow any modications or
changes to the unit EXCEPT those specied by Digital Projection in this manual.
Failure to comply with this government regulation could void your right to operate
this equipment.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant with Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a residential environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
European Waste Electrical and Electronic Equipment
(WEEE) Directive
Digital Projection Ltd is fully committed to minimising Waste Electrical and
Electronic Equipment. Our products are designed with reuse, recycling
and recovery of all components in mind. To this end, at end of life, your
projector may be returned to Digital Projection Ltd or its agent so that the
environmental impact can be minimised.
Page 7
Rev D July 2014 Page vii
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual Important Information
Digital Projection Contact details
Digital Projection Limited,
Greenside Way, Middleton, Manchester M24 1XX, UK.
Registered in England No. 2207264, Registered Ofce: as above
Tel +44 (0) 161 947 3300
Fax +44 (0) 161 684 7674
Email enquiries@digitalprojection.co.uk, service@digitalprojection.co.uk
Web Site www.digitalprojection.co.uk
Digital Projection Inc.
55 Chastain Road, Suite 115, Kennesaw, GA 30144. USA
Tel (USA) 770 420 1350
Fax (USA) 770 420 1360
Email powerinfo@digitalprojection.com
Web Site www.digitalprojection.com
Notes
Page 8
Page viii Rev D July 2014
Important Information Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Page 9
Rev D July 2014 Page ix
continued
HIGHlite Series
User Manual
Contents
Important Information
Symbols used in this guide ................................................................................................................. iii
Warnings .............................................................................................................................................iii
Trademarks ......................................................................................................................................... iii
Product revision ..................................................................................................................................... iii
Manual revision ...................................................................................................................................... iii
General precautions ..............................................................................................................................iv
Installation precautions ........................................................................................................................v
Operationandcongurationprecautions ........................................................................................v
Compliance with international standards ........................................................................................ vi
Noise .................................................................................................................................................. vi
RF Interference....................................................................................................................................vi
European Waste Electrical and Electronic Equipment (WEEE) Directive ...................................................vi
Digital Projection Contact details ..................................................................................................... vii
1. Introduction
What’s in the box? .............................................................................................................................. 1.2
Key features of the projector ........................................................................................................... 1.3
Getting to know the projector .......................................................................................................... 1.4
Front view ........................................................................................................................................ 1.4
Rear view ......................................................................................................................................... 1.4
2. Installation
Screen requirements ......................................................................................................................... 2.2
Aspect ratio ...................................................................................................................................... 2.2
Positioning the screen and projector ................................................................................................... 2.6
Screen size vs throw distance ............................................................................................................ 2.7
Choosing a lens .................................................................................................................................. 2.8
Choosing a lens using the lens charts ................................................................................................. 2.9
Choosing a lens by calculation ..........................................................................................................2.11
Fitting the lens ................................................................................................................................... 2.12
Shifting the image............................................................................................................................. 2.14
Mounting the projector .................................................................................................................... 2.15
Ceiling mounting ............................................................................................................................. 2.15
Level adjustment............................................................................................................................. 2.15
Page 10
Page x Rev D July 2014
Table of Contents Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
continued
Rear projection ............................................................................................................................... 2.16
Stacking projectors .......................................................................................................................... 2.16
Connecting the projector ................................................................................................................ 2.17
Signal Inputs .................................................................................................................................. 2.17
Control connections ........................................................................................................................ 2.19
Power connection ........................................................................................................................... 2.20
3. Getting Started
Positioning the screen and projector ............................................................................................ 3.2
Switching the projector on ............................................................................................................... 3.2
Inserting batteries into the remote control ................................................................................... 3.2
Selecting an input signal or test pattern ....................................................................................... 3.3
Input ................................................................................................................................................ 3.3
Test pattern ...................................................................................................................................... 3.3
Adjusting the lens............................................................................................................................... 3.3
Adjusting the projected image ........................................................................................................ 3.4
Aspect ratio ...................................................................................................................................... 3.4
Image quality settings ........................................................................................................................ 3.4
Switching the projector off ............................................................................................................... 3.4
4. Controlling the projector
Overview ............................................................................................................................................... 4.3
Controlling the projector..................................................................................................................... 4.3
The control panel ................................................................................................................................ 4.4
LED status indicators ........................................................................................................................ 4.4
The remote control ............................................................................................................................. 4.5
Layout ............................................................................................................................................. 4.5
Timeout ............................................................................................................................................ 4.5
Using the control keys ...................................................................................................................... 4.6
Power .............................................................................................................................................. 4.6
Source ............................................................................................................................................. 4.6
Aspect ratio ...................................................................................................................................... 4.6
User memory .................................................................................................................................... 4.6
Image quality settings ........................................................................................................................ 4.7
Test pattern ...................................................................................................................................... 4.7
Lens ................................................................................................................................................ 4.7
Using the menus ................................................................................................................................. 4.8
Navigating menus and submenus ....................................................................................................... 4.8
Main menu ............................................................................................................................................ 4.9
Aspect Ratio ..................................................................................................................................... 4.9
Presets .......................................................................................................................................... 4.10
Page 11
Rev D July 2014 Page xi
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual Table of Contents
continued
Brightness .......................................................................................................................................4.11
Contrast ..........................................................................................................................................4.11
Saturation .......................................................................................................................................4.11
Hue ................................................................................................................................................4.11
Sharpness ...................................................................................................................................... 4.12
Noise Reduction ............................................................................................................................. 4.12
Overscan ....................................................................................................................................... 4.12
Input Select .................................................................................................................................... 4.13
Resync .......................................................................................................................................... 4.13
Advanced menu ................................................................................................................................ 4.14
Colour Space ................................................................................................................................. 4.14
Video Standard ............................................................................................................................... 4.15
Gamma .......................................................................................................................................... 4.15
Colour Temperature ........................................................................................................................ 4.16
Colour Gamut ................................................................................................................................. 4.17
Dynamic Black® ............................................................................................................................. 4.17
Adaptive Contrast ........................................................................................................................... 4.17
Fine Sync ....................................................................................................................................... 4.18
RGB Adjust .................................................................................................................................... 4.19
System menu ..................................................................................................................................... 4.20
Language ....................................................................................................................................... 4.20
Source Enable ................................................................................................................................ 4.21
Menu Position................................................................................................................................. 4.22
Blank Screen .................................................................................................................................. 4.22
Auto Power On ............................................................................................................................... 4.22
Auto Power Off ............................................................................................................................... 4.22
Lamp Power ................................................................................................................................... 4.23
Rear Projection ............................................................................................................................... 4.23
Ceiling Mode .................................................................................................................................. 4.23
Logo Display .................................................................................................................................. 4.23
Control menu ..................................................................................................................................... 4.24
IR Sensor ....................................................................................................................................... 4.24
Projector Control ............................................................................................................................. 4.24
Lens Control ................................................................................................................................... 4.25
Keys 1 to 5 ..................................................................................................................................... 4.26
Trigger 1 & 2 .................................................................................................................................. 4.27
Auto Source ................................................................................................................................... 4.27
Service menu ..................................................................................................................................... 4.28
Factory Reset ................................................................................................................................. 4.28
Blue Only ....................................................................................................................................... 4.29
Test Patterns .................................................................................................................................. 4.29
Altitude .......................................................................................................................................... 4.29
Page 12
Page xii Rev D July 2014
Table of Contents Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
5. Maintenance
Changing the lamp module .............................................................................................................. 5.2
Cleaning the fans ................................................................................................................................ 5.3
Cleaningorreplacingtheairlter .................................................................................................. 5.4
6. Appendix
Troubleshooting .................................................................................................................................. 6.2
Error codes ...................................................................................................................................... 6.4
Dimensions .......................................................................................................................................... 6.5
Specications ...................................................................................................................................... 6.6
Part numbers .................................................................................................................................... 6.6
Optical ............................................................................................................................................. 6.6
Electrical .......................................................................................................................................... 6.7
Physical ........................................................................................................................................... 6.7
Video formats supported ................................................................................................................ 6.10
Input connections ............................................................................................................................. 6.12
HDMI 1 & 2 inputs ........................................................................................................................... 6.12
Composite video input ..................................................................................................................... 6.12
S-Video input .................................................................................................................................. 6.12
RGB input ...................................................................................................................................... 6.13
Component 1 input .......................................................................................................................... 6.13
Component 2 input .......................................................................................................................... 6.13
Control connections ........................................................................................................................ 6.14
Wired Remote control connection ..................................................................................................... 6.14
Trigger 1 & 2 output ........................................................................................................................ 6.14
Serial control input .......................................................................................................................... 6.14
Remote communications protocol ............................................................................................... 6.16
Introduction .................................................................................................................................... 6.16
Key Commands .............................................................................................................................. 6.16
Operation Commands ..................................................................................................................... 6.18
Setting the LAN IP conguration ....................................................................................................... 6.23
Page 13
Rev D July 2014 Page 1.1
1. Introduction
Contents
What’s in the box? .............................................................................................................................. 1.2
Key features of the projector ........................................................................................................... 1.3
Getting to know the projector .......................................................................................................... 1.4
Front view ........................................................................................................................................ 1.4
Rear view ......................................................................................................................................... 1.4
Page 14
Page 1.2 Rev D July 2014
1. Introduction Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
What’s in the box?
• Make sure your box contains everything listed. If any pieces are missing, contact
your dealer.
• You should save the original box and packing materials, in case you ever need
to ship your Projector.
Notes
For more detailed information
about lenses, see Screen size
vs throw distance, in section
2. Installation.
Only one power cable -
dependent on the destination
territory - will be supplied with
the projector.
Important Information
(111-369)
User Manual on disc
(115-759)
Remote control
(110-024)
2x AA batteries
HDMI cable
Getting Started Guide
(111-370)
Power cable 10A
United Kingdom
(102-180)
Power cable 13A
North America
(102-165)
Power cable 10A
Europe
(102-163)
Projector
HIGHlite 260 HB (110-509)
HIGHlite 260 HC (110-016)
HIGHlite 1080p 330 (110-748)
Page 15
Rev D July 2014 Page 1.3
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 1. Introduction
Notes
Key features of the projector
Congratulations on your purchase of the Digital Projection HIGHlite Series
projector.
Digital Projection International (DPI), Texas Instruments’ rst DLP® partner and
the original innovator of the 3-chip DLP® projector, proudly introduces the new
HIGHlite Series, a high brightness 1080p platform with the imaging delity of Texas
Instruments’ DLP® technology. The 3-chip HIGHlite Series adds a remarkably
affordable, high-lumen line of 1920 x 1080 displays to DPI’s already extensive 3chip product line.
The imagery benets associated with the HIGHlite Series are numerous, with
dazzlingly bright images and superior DLP® image delity. Applicable to a wide
variety of home and commercial venues, including those contending with high
ambient light, the series offers rich, saturated imagery. Augmenting these benets is
the incredible efciency of the single lamp, meaning the projector produces beautiful
imagery while consuming a fraction of the wattage of similar products.
Installation is incredibly exible due to the HIGHlite’s compact and lightweight
chassis design, and extraordinary lens shift range of up to 30% horizontal and up
to 120% vertical. Multiple lens options provide further exibility, with a throw range
from .77 to 6.76:1. Connectivity includes two HDMI inputs, as well as RGB via D-15,
component, composite and S-Video inputs.
Providing a bright, saturated image from a small form 3-chip display, the HIGHlite
Series presents a powerful yet remarkably affordable solution for a Variety of
commercial and home entertainment applications, including: media rooms and
home theatres, training and education, boardrooms and conference centers,
visualization/simulation environments, retail, entertainment, digital media/advertising
and hospitality.
Key Features
• High resolution projector for medium sized venues
• Applications: Medium sized Screen; Fixed install and Rental
• Brightness: 260 HC 2000 ANSI lumens ±10%
260 HB 3500 ANSI lumens ±10%
1080p 330 4500 ANSI lumens ±10%
• Contrast: 260 HC 20000:1 ±10% (with HC lens and Dynamic Black)
260 HB 2000:1 ±10%
1080p 330 2000:1 ±10%
• 1920 x 1080 resolution
• Precision mechanical design ensuring maximum amount of light from lamp
housing reaches optics, without any operator adjustment
• Power consumption: 400-500W single phase, 100-240VAC ±10%
• Compact size, light weight - approximately 20 kg (44 lbs)
• Robust metal case
• RS232 and LAN connection for remote operation using control codes
• Seven selectable Digital and Analogue Video inputs for display of the latest as
well as legacy video standards.
HDMI, RGBHV, Component, S-Video, Composite all as standard
• IR remote control for easy setup
Page 16
Page 1.4 Rev D July 2014
1. Introduction Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Notes
For more detailed information
about lenses or lens shift, see
section 2. Installation
For information about how to
change the lamp or the lter,
see section 5. Maintenance.
For information about controls
and indicators, see section
4. Controlling the projector.
Getting to know the projector
Front view
Rear view
Rear Infra-red window
(remote control)
Power
connection
Lens
Front Infra-red
window
(remote control)
Air outlet
Air inlet
Input
connections
Adjustable
feet
Projector
control
panel
Air inlet
Page 17
Rev D July 2014 Page 2.1
2. Installation
Contents
Screen requirements ......................................................................................................................... 2.2
Aspect ratio ...................................................................................................................................... 2.2
Fitting the image to the DMD ............................................................................................................. 2.2
Examples of 16:9 images displayed with different aspect ratio settings ........................................................ 2.2
Examples of 4:3 images displayed with different aspect ratio settings ......................................................... 2.3
Examples of 2.35:1 images displayed with different aspect ratio settings ..................................................... 2.3
Diagonal screen sizes ...................................................................................................................... 2.4
Fitting the image to the screen ........................................................................................................... 2.5
Positioning the screen and projector ................................................................................................... 2.6
Optimum viewing position ................................................................................................................. 2.6
Screen size vs throw distance ............................................................................................................ 2.7
Calculating screen width and throw distance ......................................................................................... 2.7
Choosing a lens .................................................................................................................................. 2.8
Choosing a lens using the lens charts ................................................................................................. 2.9
Full width images, including 2.35:1, and 16:9 (native resolution) ................................................................ 2.9
example ....................................................................................................................................... 2.9
Choosing a lens by calculation ..........................................................................................................2.11
Example ......................................................................................................................................2.11
Fitting the lens ................................................................................................................................... 2.12
Shifting the image............................................................................................................................. 2.14
Mounting the projector .................................................................................................................... 2.15
Ceiling mounting ............................................................................................................................. 2.15
Level adjustment............................................................................................................................. 2.15
Rear projection ............................................................................................................................... 2.16
Stacking projectors .......................................................................................................................... 2.16
Connecting the projector ................................................................................................................ 2.17
Signal Inputs .................................................................................................................................. 2.17
Input connection examples .............................................................................................................. 2.17
Control connections ........................................................................................................................ 2.19
Remote control ............................................................................................................................. 2.19
RS232 and LAN connections .......................................................................................................... 2.19
Trigger 1 & 2 ................................................................................................................................ 2.19
Power connection ........................................................................................................................... 2.20
Page 18
Page 2.2 Rev D July 2014
2. Installation Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Screen requirements
Aspect ratio
Fitting the image to the DMD
The projector uses a DMD (Digital Mirror Device) to create the image that is
projected onto the screen. The resolution of the DMD in this projector is 1920 x
1080 pixels, or to put it another way, its aspect ratio is 16:9.
If the source image supplied to the projector has a different aspect ratio from this,
or even if it has the same aspect ratio but fewer pixels, then the image will not ll
the DMD. The projector therefore needs to scale the image.
The projector has ve aspect ratio settings, so that you can choose the one that is
most suitable for your image source. The settings are:
16:9 the image is scaled to ll the DMD (and thus, a 16:9 screen).
Theaterscope the image is scaled such that a 2.35:1 image will be displayed
at the correct aspect ratio when the projector is tted with an
anamorphic lens. Thus an image with an aspect ratio of 2.35:1
can be displayed using the full 16:9 resolution of the DMD.
4:3 the image is scaled to t a 4:3 screen, using the full height of the
DMD.
4:3 Narrow to be used for 4:3 images in combination with an anamorphic
lens. The image is scaled to t the DMD vertically, but squeezed
horizontally such that the lens will stretch it to the correct ratio.
Native the image is displayed with no scaling, at its original resolution, in
the centre of the screen.
Examples of 16:9 images displayed with different aspect ratio settings
Note that, as the aspect ratio of the image matches that of the DMD, the 16:9
setting is best, unless there is some specic reason for wanting the smaller image,
for instance, to maintain the same scale as other images from the same source.
Notes
For more information about
changing the Aspect ratio
setting, see Using the control
keys and Using the menus
in section 4. Controlling the
Projector.
The 16:9 image shown here has
far fewer pixels than the 1920 x
1080 of the DMD. Your image
may be different.
1920 pixels
1080 pixels
9 units
16 units
16:9
Native
Page 19
Rev D July 2014 Page 2.3
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 2. Installation
Examples of 4:3 images displayed with different aspect ratio settings
The 4:3 setting is best, unless there is some specic reason for wanting the smaller
Native image, for instance, to maintain the same scale as other images from the
same source.
If you are using an anamorphic lens, the 4:3 Narrow setting should be used. The
lens will stretch the image to the correct width.
Examples of 2.35:1 images displayed with different aspect ratio
settings
The 16:9 setting is best, unless there is some specic reason for wanting the
smaller Native image, for instance, to maintain the same scale as other images from
the same source.
If you have an anamorphic lens, the Theaterscope setting would be a much better
option. Because it uses the whole of the DMD, it will be a much brighter image than
the letterboxed options shown above, and will ll a wider screen if this is available.
Notes
The 4:3 image shown here has
far fewer pixels than the 1920 x
1080 of the DMD. Your image
may be different.
If you are using an anamorphic
lens, you will need to use the
4:3 Narrow setting to correct the
image.
The 2.35 image shown here has
far fewer pixels than the 1920 x
1080 of the DMD. Your image
may be different.
To take advantage of the
Theaterscope setting, you
MUST have an anamorphic
lens.
Theaterscope
without Anamorphic lens
with Anamorphic lens,
stretched to ll wider screen
4:3
Native
16:9 Native
4:3 Narrow
without anamorphic lens
4:3 Narrow
with anamorphic lens
Page 20
Page 2.4 Rev D July 2014
2. Installation Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Diagonal screen sizes
Screen sizes are sometimes specied by their diagonal size (D) in inches. When
dealing with large screens and projection distances at different aspect ratios, it is
more convenient to measure screen width (W) and height (H).
The example calculations below show how to convert diagonal sizes in inches into
width and height, at various aspect ratios.
2.35:1 (Scope)
W = D x 0.92in (D x .023m) H = D x 0.39in (D x .01m)
1.85:1
W = D x 0.88in (D x .022m) H = D x 0.47in (D x .012m)
16:9 = 1.78:1 (native aspect ratio)
W = D x 0.87in (D x .022m) H = D x 0.49in (D x .0125m)
1.66:1 (Vista)
W = D x 0.86in (D x .022m) H = D x 0.52in (D x .013m)
16:10 = 1.6:1
W = D x 0.85in (D x .022m) H = D x 0.53in (D x .014m)
4:3 = 1.33:1
W = D x 0.8in (D x .02m) H = D x 0.6in (D x .015m)
D = diagonal (inches)
W = width
H = height
Notes
Page 21
Rev D July 2014 Page 2.5
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 2. Installation
Fitting the image to the screen
It is important that your screen is of sufcient height and width to display images at
all the aspect ratios you are planning to use.
Use the conversion chart, or the sample calculations below to check that you are
able to display the full image on your screen. If you have insufcient height or width,
you will have to reduce the overall image size in order to display the full image on
your screen.
Notes
2.35:1 (Scope)
W = H x 2.35 H = W x 0.426
1.85:1
W = H x 1.85 H = W x 0.54
16:9 = 1.78:1 (native aspect ratio)
W = H x 1.78 H = W x 0.56
1.66:1 (Vista)
W = H x 1.66 H = W x 0.6
16:10 = 1.6:1
W = H x 1.6 H = W x 0.625
4:3 = 1.33:1
W = H x 1.33 H = W x 0.75
1 2 3 4 5 6 7 8 9 10
Screen width
Screen height
4:3
16:9
2.35:1
Aspect ratio
10
9
8
7
6
5
4
3
2
1
1.85:1
1.66:1
16:10
Page 22
Page 2.6 Rev D July 2014
2. Installation Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Positioning the screen and projector
Optimum viewing position
For optimum viewing, the screen should be a at surface perpendicular to the oor.
The bottom of the screen should be 1.2m (4 feet) above the oor and the front row
of the audience should not have to look up more than 30° to see the top of the
screen.
The distance between the front row of the audience and the screen should be at
least twice the screen height and the distance between the back row and the screen
should be a maximum of 8 times the screen height. The screen viewing area should
be within a 60° range from the face of the screen.
Notes
The projector should be
installed as close to the
power outlet as possible.
The power connection should
be easily accessible, so that
it can be disconnected in an
emergency.
Ensure that there is at least
30cm (12in) of space between
the ventilation outlets and
any wall, and 10cm (4in) on
all other sides.
Do not install the projector
close to anything that
might be affected by its
operational heat, for instance,
polystyrene ceiling tiles,
curtains etc.
The image can be ipped for
rear projection (see section
4. Using the menus, Image
menu) and displayed without
the need for extra mirrors or
equipment.
However, you must ensure
that there is sufcient distance
behind the screen for the
projector to be correctly located.
Rear installation is generally
more complicated and advice
should be sought from your
local dealer before attempting it.
Page 23
Rev D July 2014 Page 2.7
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 2. Installation
Screen size vs throw distance
Throw distance is the distance measured from the front of the projector to the
screen. This is an important calculation in any projector installation as it determines
whether or not you have enough room to install your projector with the desired
screen size, and if your image will be the right size for your screen.
Calculating screen width and throw distance
Throw Distance = Screen Width x Lens Throw Ratio
Screen Width = Throw Distance
Lens Throw Ratio
The following lens calculations may be useful:
Throw ratio = Throw distance
Screen width
Throw ratio factor (TRF) = DMD width in pixels = 1920
image width in pixels image width in pixels
Therefore:
Screen width = Throw distance
Throw ratio x TRF
Throw distance = Screen width x Throw ratio x TRF
Notes
For more information about the
relationship between screen
size, throw distance and lenses,
see Choosing a lens on the
following pages.
The Throw ratio for a particular
lens is xed, but assumes that
the image lls the width of the
DMD.
For images that do not ll the
width of the DMD, the Throw
ratio is effectively increased.
To correct for this in these
calculations, a Throw Ratio
Factor (TRF) is used.
Page 24
Page 2.8 Rev D July 2014
2. Installation Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Notes
The High Brightness lenses
are recommended for the High
Brightness model, for maximum
light output.
The High Contrast lenses are
recommended for the High
Contrast models, for maximum
contrast.
ONLY the High Brightness
lenses are recommended for
the 1080p 330.
For more information about
Throw ratio factor (TRF), see
the previous page.
Choosing a lens
A number of lenses are available for use with the projector. Which lens you choose
will depend on the screen size, image aspect ratio, projection distance and light
output.
The lenses available and their part numbers are listed below:
High Brightness High Contrast
0.77 : 1 xed lens 110-808 110-022
1.16 : 1 xed lens 110-809 110-023
1.45 - 1.74 : 1 zoom lens 110-803 110-017
1.74 - 2.17: 1 zoom lens 110-804 110-018
2.17 - 2.9: 1 zoom lens 110-805 110-019
2.9 - 4.34: 1 zoom lens 110-806 110-020
4.34 - 6.76: 1 zoom lens 110-807 110-021
If the image does not ll the full width of the DMD, this effectively increases the
throw ratio of the lens. This can be corrected for by applying a Throw ratio factor.
Method one: using the lens charts
For the screen sizes listed below, use the charts on the following pages, to choose
the most suitable lens.
Full width images, including:
2.35:1 (Scope) 1920 x 817 pixels
16:9 = 1.78:1 1920 x 1080 pixels (native resolution)
4:3 images
A Throw ratio factor (TRF) has been applied to the following chart:
4:3 = 1.33:1 1440 x 1080 pixels TRF = 1.33
Method two: by calculation
See the calculations, on the page immediately following the lens charts.
Page 25
Rev D July 2014 Page 2.9
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 2. Installation
Notes
This chart has a TRF of 1.0, for
use with the following images:
Choosing a lens using the lens charts
Use the charts on this page and on the following pages to choose which lens best
suits your application.
Full width images, including 2.35:1, and 16:9 (native resolution)
example
• For a screen width of 4m at a distance of 15m, the 2.9- 4.34: 1 zoom lens would
be best suited.
• For the same screen size at a distance of 20m, the 4.34 - 6.76: 1 zoom lens
would be best suited.
if you need to be more precise, then use the calculations on the page immediately
following the lens charts.
16:9
and 2.35:1
1.16 : 1 xed lens
110-023
110-809
1.74 - 2.17: 1
zoom lens
110-018
110-804
2.17 - 2.9: 1
zoom lens
110-019
110-805
4.34 - 6.76: 1
zoom lens
110-021
110-807
0.77 : 1 xed lens
110-022
110-808
feet
metres
Screen width
10 20 30 40 metres
33 66 98 131 feet
20 6
16 5
13 4
10 3
7 2
3 1
Throw distance
2.9 - 4.34: 1
zoom lens
110-020
110-806
1.45 - 1.74 : 1
zoom lens
110-017
110-803
Page 26
Page 2.10 Rev D July 2014
2. Installation Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Lens charts continued
Notes
This chart has a TRF of 1.33,
for use with the following
images:
4:3 = 1.33
Full height image 4:3
Use the chart below to choose which lens best suits your application.
if you need to be more precise, then use the calculations on the page immediately
following the lens charts.
1.16 : 1 xed lens
110-023
110-809
1.74 - 2.17: 1
zoom lens
110-018
110-804
2.17 - 2.9: 1
zoom lens
110-019
110-805
4.34 - 6.76: 1
zoom lens
110-021
110-807
0.77 : 1 xed lens
110-022
110-808
feet
metres
Screen width
10 20 30 40 metres
33 66 98 131 feet
20 6
16 5
13 4
10 3
7 2
3 1
2.9 - 4.34: 1
zoom lens
110-020
110-806
1.45 - 1.74 : 1
zoom lens
110-017
110-803
Page 27
Rev D July 2014 Page 2.11
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 2. Installation
Notes
The Throw ratio for a particular
lens is xed, but assumes that
the image lls the width of the
DMD.
For images that do not ll the
width of the DMD, the Throw
ratio is effectively increased.
To correct for this in these
calculations, a Throw Ratio
Factor (TRF) is used.
ONLY the High Brightness
lenses are recommended for
the 1080p 330.
Choosing a lens by calculation
For any screen size not listed above, or if you need to be more precise, then use the
calculations below.
• Identify actual width of the image in pixels.
• Calculate the Throw Ratio Factor: TRF = DMD width (1920)
Image width in pixels
• Identify the screen width required.
• Identify the throw distance required.
Throw distance calculations are based on the distance from the outer end of the
lens, which will vary from lens to lens. Once a lens has been chosen, the gures
can be checked using the lens extension values given below.
• Calculate the throw ratio required. Throw ratio = Throw distance
Screen width x TRF
• Choose a lens with the required throw ratio from the list at the bottom of the
page.
Check from the list that the lens chosen will work at the throw distance required.
Example
• An image, 1024 x 768 pixels, screen width 3.0m, throw distance 17m from the
outer end of the lens.
• Throw Ratio Factor (TRF) = 1920 = 1.875
1024
• Throw ratio required = 17 = 3.02
3.0 x 1.875
• Choose the 2.9 - 4.34 : 1 zoom lens.
High Brightness High Contrast Extension Throw distance range
0.77 : 1 xed lens 110-808 110-022 80 mm (3.2 in) 1.3 - 2.5m (4.3 - 8.2ft)
1.16 : 1 xed lens 110-809 110-023 54 mm (2.1 in) 1.4 - 6.2m (4.6 - 20.3ft)
1.45 - 1.74 : 1 zoom lens 110-803 110-017 24 mm (1.0 in) Wide: 1.8 - 7.6m (5.9 - 24.9ft)
Tele: 2.2 - 9.3m (7.2 - 30.5ft)
1.74 - 2.17: 1 zoom lens 110-804 110-018 n/a Wide: 2.2 - 9.5m (7.2 - 31.2ft)
Tele: 2.7 - 11.8m (8.9 - 38.7ft)
2.17 - 2.9: 1 zoom lens 110-805 110-019 n/a Wide: 2.7 - 11.5m (8.9 - 37.7ft)
Tele: 3.7 - 15.4m (12.1 - 50.5ft)
2.9 - 4.34: 1 zoom lens 110-806 110-020 n/a Wide: 3.6 - 14.7m (11.8 - 48.2ft)
Tele: 5.5 - 22.5m (18 - 73.8ft)
4.34 - 6.76: 1 zoom lens 110-807 110-021 n/a Wide: 5.5 - 22m (18 - 72.2ft)
Tele: 8.6 - 35m (28.2 - 114.8ft)
Page 28
Page 2.12 Rev D July 2014
2. Installation Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Notes
Make sure the rear lens cap is
removed, before tting the lens.
Be careful not to scratch
the lens surfaces. If you do
accidentally touch a lens, then
clean the surface using a lens
paper.
Fitting the lens
• Remove the two screws securing the front cover to the body of the projector.
• Push the front cover downwards, then pull it away from the projector.
• Push down the lens holder tab.
• Hold down the tab, and insert the lens into the lens aperture, making sure that
the plug on the zoom drive mechanism lines up with the socket on the right of
the lens aperture.
securing
screw
securing
screw
lens
holder tab
Page 29
Rev D July 2014 Page 2.13
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 2. Installation
Notes
Make sure the rear lens cap is
removed, before tting the lens.
Be careful not to scratch
the lens surfaces. If you do
accidentally touch a lens, then
clean the surface using a lens
paper.
• Still holding down the tab, push the lens in rmly as far as it will go.
• Rotate the lens clockwise as far as it will go.
• Release the lens holder tab.
• Position the front cover as shown below, hold it against the front of the projector,
then push it upwards into place.
• Replace the two screws.
Page 30
Page 2.14 Rev D July 2014
2. Installation Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Shifting the image
Ideally, the projector should be positioned perpendicular to the screen.
The normal position for the projector is at the centre of the screen. However, with
the zoom lenses, you can set the projector above or below the centre, or to one
side, and adjust the image using the Lens shift controls on the top of the projector
to maintain a geometrically correct image.
The maximum range available with no distortion is dependent on which zoom lens is
used. The tables below show the maximum range for images that ll the DMD. For
images which do not use the full height or width, extra shift may be possible, up to
the limit of the lens mount movement.
xed lenses
vertical
(pixels)
horizontal
(pixels)
vertical
(vs DMD height)
horizontal
(vs DMD width)
+ 216 ± 96 + 0.2H (40%) ± 0.05W (10%)
zoom lenses
vertical
(pixels)
horizontal
(pixels)
vertical
(vs DMD height)
horizontal
(vs DMD width)
± 648 ± 288 ± 0.6H (120%) ± 0.15W (30%)
It is physically possible to shift the lens further than this, however there will be some
distortion of the image beyond the ranges specied above.
Notes
For more information on using
the Lens shift feature, see
section 4. Using the menus,
Using the control keys.
If the lens is to be shifted in
two directions combined, the
maximum range is somewhat
less, as can be seen below.
(zoom lens shift shown).
full horizontal or vertical shift
without distortion
combined shift
is reduced
Page 31
Rev D July 2014 Page 2.15
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 2. Installation
Mounting the projector
The four adjustable feet under the chassis allow the projector to be lowered onto a
at surface without any danger of hands being trapped between the bottom frame
and the surface.
Ceiling mounting
The projector is designed to be used on a at surface, but it can be suspended
from a ceiling. Four M4 mounting holes with a 0.7mm pitch are provided under the
projector to allow bolting to a ceiling mounting plate.
To use the projector upside down, set Ceiling mode to On, in the System menu, to
invert the image.
Level adjustment
If the projector is to be operated from a at surface such as a projector table, then
adjustment of projector level should be made by turning the four feet under the
chassis.
Ideally, the projector should be positioned perpendicular to the screen, and the lens
shift controls used to align the image with the screen, to maintain a geometrically
correct image.
Notes
BEFORE INSTALLING THE
PROJECTOR, READ ALL THE
WARNINGS BELOW AND
ALL THOSE IN IMPORTANT
INFORMATION AT THE
FRONT OF THIS MANUAL.
The projector weighs
approximately 20 kg (44 lbs).
Use safe handling techniques
when lifting the projector.
Make sure that the surface,
ceiling or rigging that is
to support the projector is
capable of supporting the
weight of the projector.
Backup safety chains or
wires should always be
used with ceiling mount
installations.
Do not tilt the projector more
than ±8.5° forwards and
backwards when in use, as
this may cause serious lamp
failure, damage the lamp
module and cause extra
cost on replacement. The
projector my be tilted left and
right as necessary.
Dimensions
in mm
±8.5°
±8.5°
Page 32
Page 2.16 Rev D July 2014
2. Installation Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Notes
For more detailed information
about using the menus, see
section 4. Controlling the
projector.
Do not try to stack more than
three projectors.
When stacking projectors,
the stack MUST be vertical, to
ensure that the stresses are
distributed to all four chassis
corners.
Make sure that the surface,
ceiling or rigging that is
to support the projector is
capable of supporting the
combined weight of all the
projectors.
Do not place heavy objects
on top of the projector
chassis. Only the chassis
corners are capable of
withstanding the weight of
another projector.
Backup safety chains or
wires should always be
used with ceiling mount
installations.
Stacking projectors
The projector is capable of supporting the weight of up to three other projectors
safely. The stack should be positioned vertically and perpendicular to the screen,
and the lens shift controls used to align the image with the screen, to maintain a
geometrically correct image.
• Carefully lower each projector down onto the top of the others, making sure that
they are vertically aligned with each other, and protected from becoming pushed
over.
• Align the images from the projectors, using the Lens shift controls on the top of
the projector.
Rear projection
To use rear projection, set Rear Projection to On, in the System menu, to reverse
the image.
In rear-screen applications where space behind the projector is limited, a mirror may
be used to fold the optical path. The position of the projector and mirror must be
accurately set. If you are considering this type of installation, contact your dealer for
assistance
Page 33
Rev D July 2014 Page 2.17
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 2. Installation
Notes
For more information on
selecting an input source, see
section 4. Overview, Using
the control keys, and Using
the menus.
For more information about pin
connections and control codes
see section 6. Appendix.
Connecting the projector
Signal Inputs
The following inputs are available:
HDMI 1 & 2 HDCP-compliant digital video inputs from HDMI or DVI sources.
RGB 15 pin D-type VGA style input from personal computer
Component 1 RCA phono connectors for RGBS, (using Video input for sync)
or YPbPr
Component 2 BNC connectors for RGB or RGBHV
Video RCA phono connector for composite video
or used as sync input for Component 1
S-Video standard 4 pin S-Video connector
Input connection examples
Component 2
HDMI 1 HDMI 2
RGB
Component 1
VideoS-Video
Page 34
Page 2.18 Rev D July 2014
2. Installation Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Input connection examples, continued
Page 35
Rev D July 2014 Page 2.19
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 2. Installation
Notes
For more information about pin
connections and control codes
see section 6. Appendix.
For information how to enable
and disable the remote control,
see Control Menu in section
4. Controlling the projector,
and Remote communications
protocol, in section 6.
Appendix.
For more information how to
switch between RS232 and
LAN control see Control Menu
in section 4. Controlling
the projector, and Remote
communications protocol, in
section 6. Appendix.
For more information about the
Trigger outputs see Control
Menu in section 4. Controlling
the projector.
Control connections
The following connections are available:
Remote control
If infrared signals from the remote control cannot reach the projector due to
excessive distance or obstructions such as walls or cabinet doors, you can connect
an external IR repeater to the Remote control input, and position its IR sensor within
range of the operator.
RS232 and LAN connections
All of the projector’s features can be controlled using an external control system,
or a PC using a terminal-emulation program such as HyperTerminal, via a serial
or LAN connection. This is done by using the text strings described in Remote
communications protocol, in section 6. Appendix.
The RS232 or LAN connection can also be used to download the rmware updates,
issued from time to time by Digital Projection.
Trigger 1 & 2
The Trigger 1 and Trigger 2 outputs are interchangeable:
Screen trigger: can be connected to an electrically operated screen,
automatically deploying the screen when the projector
starts up, and retracting the screen when the projector
shuts down.
Aspect Ratio trigger: can be used to control screen shuttering for different
aspect ratios
Projector
Computer
RS232
Trigger 1
Remote control
Trigger 2
LAN
Page 36
Page 2.20 Rev D July 2014
2. Installation Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Power connection
• Push the cable lock to the left, plug the mains connector in rmly, then push the
lock back to secure the cable.
• Switch on at the switch next to the power connector.
Notes
Use only the power cable
provided.
Ensure that the power
outlet includes a Ground
connection, as this
equipment MUST be earthed.
Handle the power cable
carefully and avoid sharp
bends. Do not use a damaged
power cable.
Power
connection
Page 37
Rev D July 2014 Page 3.1
3. Getting Started
Contents
Positioning the screen and projector ............................................................................................ 3.2
Switching the projector on ............................................................................................................... 3.2
Inserting batteries into the remote control ................................................................................... 3.2
Selecting an input signal or test pattern ....................................................................................... 3.3
Input ................................................................................................................................................ 3.3
Test pattern ...................................................................................................................................... 3.3
Adjusting the projected image ........................................................................................................ 3.4
Aspect ratio ...................................................................................................................................... 3.4
Image quality settings ........................................................................................................................ 3.4
Switching the projector off ............................................................................................................... 3.4
Page 38
Page 3.2 Rev D July 2014
3. Getting Started Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Switching the projector on
• Connect the power cable between the mains supply and the projector. Switch on
at the switch next to the power connector.
Wait until the self-test has completed and the standby indicator on the projector
control panel shows amber. The lamp will be off and the projector will be in
STANDBY mode.
• Press POWER ON on the remote control or POWER on the projector
control panel to switch the projector ON. The power indicator on the control
panel will ash blue for approximately 30 seconds, whilst the lamp comes up to
full brightness. When the projector is ready for use, the power indicator will show
a steady blue.
Notes
For more information about
positioning the screen and
projector, see Positioning
the screen and projector, in
section 2. of the User Manual:
Installation.
For more detailed information
about:
- using the control keys on the
remote control or the projector
control panel,
- using the menus,
see section 4. of the User
Manual: Controlling the
projector.
If the red ISSUE indicator is
illuminated continuously or
ashing, see Error Codes in
section 6 of the User Manual:
Appendix, for more information
Do not mix an old battery with
a new one or different types of
batteries.
If you will not use the remote
control for a long time, remove
the batteries to avoid damage
from battery leakage.
Inserting batteries into the remote control
• Open the battery compartment and insert two AA size batteries, making sure
they are inserted the correct way round, as shown below.
Positioning the screen and projector
• Install the screen, ensuring that it is in the best position for viewing by your
audience.
• Mount the projector, ensuring that it is at a suitable distance from the screen for
the image to ll the screen, and that it is perpendicular to the sceen.
Power
connection
Projector
control
panel
Page 39
Rev D July 2014 Page 3.3
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 3. Getting Started
Selecting an input signal or test pattern
Input
• Connect an video source to the projector. The signal should be automatically
detected by the projector, and should be displayed within a two or three
seconds.
• If more than one signal is connected to the projector, then select which signal
is to be displayed, using the to buttons on the remote control, or
by pressing the SOURCE button on the projector control panel until the correct
signal is displayed.
Test pattern
If you have no video source connected to the projector, then you can display a test
pattern as follows:
• Press on the remote control, until the desired test pattern is displayed.
Notes
For more information about
connecting input signals, see
Signal Inputs, in section 2. of
the User Manual: Installation.
For more detailed information
about input connections, see
Input signals in section 6. of
the User Manual: Controlling
the projector.
For more information about lens
shift, see Shifting the image in
section 2. of the User Manual:
Installation.
Adjusting the lens
• Press the key repeatedly to cycle through the Lens adjustments, in the
following order:
Focus, Zoom, Shift...
• Use the use the , , and keys to adjust the lens.
Example - Lens Shift control:
Page 40
Page 3.4 Rev D July 2014
3. Getting Started Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Adjusting the projected image
Aspect ratio
• Press on the remote control until the image is displayed in the corect aspect
ratio.
Image quality settings
• Press any of the following keys on the remote control, followed by and , to
adjust these image quality settings:
Brightness
Contrast
Sharpness
Notes
For more detailed information
about:
- using all the control keys
on the remote control or the
projector control panel,
- using the menus,
see section 4. of the User
Manual: Controlling the
projector.
For the picture setting
adjustments shown here:
- after 5 seconds, if no
adjustment has been made,
the indicator will go out and
the adjustment key must be
pressed again.
- to end the adjustment before
5 seconds has elapsed, press
a different adjustment key, or
press the key again.
Always allow the lamp to cool
for 5 minutes before:
- disconnecting the power
- moving the projector
- changing the lamp
- cleaning the fans and lter
Switching the projector off
• Press POWER OFF on the remote control or POWER on the
projector control panel, then press the button a second time to conrm your
intention to switch off.
The lamp will switch off, and the power indicator on the control panel will ash
blue for approximately 30 seconds until the lamp has cooled down.
• Wait until the power indicator has switched off and the standby indicator on the
projector control panel shows amber. The projector will now be in STANDBY
mode.
• Switch off the power switch next to the power connection, then disconnect the
power cable from the projector.
Page 41
Rev D July 2014 Page 4.1
4. Controlling the projector
Contents
Adjusting the lens............................................................................................................................... 3.3
Example - Lens Shift control: ............................................................................................................. 3.3
Overview ............................................................................................................................................... 4.3
Controlling the projector..................................................................................................................... 4.3
The control panel ................................................................................................................................ 4.4
LED status indicators ........................................................................................................................ 4.4
The remote control ............................................................................................................................. 4.5
Layout ............................................................................................................................................. 4.5
Timeout ............................................................................................................................................ 4.5
Using the control keys ...................................................................................................................... 4.6
Power .............................................................................................................................................. 4.6
Source ............................................................................................................................................. 4.6
Aspect ratio ...................................................................................................................................... 4.6
User memory .................................................................................................................................... 4.6
Image quality settings ........................................................................................................................ 4.7
Example - Brightness screen control: .................................................................................................. 4.7
Test pattern ...................................................................................................................................... 4.7
Lens ................................................................................................................................................ 4.7
Example - Lens Shift control: ............................................................................................................. 4.7
Using the menus ................................................................................................................................. 4.8
Navigating menus and submenus ....................................................................................................... 4.8
Main menu ............................................................................................................................................ 4.9
Aspect Ratio ..................................................................................................................................... 4.9
Presets .......................................................................................................................................... 4.10
Recall Presets .............................................................................................................................. 4.10
Save Presets ............................................................................................................................... 4.10
Brightness .......................................................................................................................................4.11
Contrast ..........................................................................................................................................4.11
Saturation .......................................................................................................................................4.11
Hue ................................................................................................................................................4.11
Sharpness ...................................................................................................................................... 4.12
Noise Reduction ............................................................................................................................. 4.12
Overscan ....................................................................................................................................... 4.12
Input Select .................................................................................................................................... 4.13
Resync .......................................................................................................................................... 4.13
Advanced menu ................................................................................................................................ 4.14
Colour Space ................................................................................................................................. 4.14
continued
Page 42
Page 4.2 Rev D July 2014
4. Controlling the projector Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Video Standard ............................................................................................................................... 4.15
Gamma .......................................................................................................................................... 4.15
Colour Temperature ........................................................................................................................ 4.16
Colour Gamut ................................................................................................................................. 4.17
Dynamic Black® ............................................................................................................................. 4.17
Adaptive Contrast ........................................................................................................................... 4.17
Fine Sync ....................................................................................................................................... 4.18
RGB Adjust .................................................................................................................................... 4.19
Offsets ....................................................................................................................................... 4.19
Gains ......................................................................................................................................... 4.19
System menu ..................................................................................................................................... 4.20
Language ....................................................................................................................................... 4.20
Source Enable ................................................................................................................................ 4.21
Menu Position................................................................................................................................. 4.22
Blank Screen .................................................................................................................................. 4.22
Auto Power On ............................................................................................................................... 4.22
Auto Power Off ............................................................................................................................... 4.22
Lamp Power ................................................................................................................................... 4.23
Rear Projection ............................................................................................................................... 4.23
Ceiling Mode .................................................................................................................................. 4.23
Logo Display .................................................................................................................................. 4.23
Control menu ..................................................................................................................................... 4.24
IR Sensor ....................................................................................................................................... 4.24
Projector Control ............................................................................................................................. 4.24
Lens Control ................................................................................................................................... 4.25
Example - Lens Shift control: ........................................................................................................... 4.25
Keys 1 to 5 ..................................................................................................................................... 4.26
Trigger 1 & 2 .................................................................................................................................. 4.27
Auto Source ................................................................................................................................... 4.27
Service menu ..................................................................................................................................... 4.28
Factory Reset ................................................................................................................................. 4.28
Blue Only ....................................................................................................................................... 4.29
Test Patterns .................................................................................................................................. 4.29
Altitude .......................................................................................................................................... 4.29
Page 43
Rev D July 2014 Page 4.3
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 4. Controlling the projector
Overview
Controlling the projector
The projector can be controlled from:
• the remote control
• the projector control panel
• the RS232 input
For more information about controlling the projector using the RS232 input, see
Remote communications protocol in section 6. Appendix.
For information about how to connect the projector, see Connecting the
projector in section 2. Installation, and Connections in section 6. Appendix.
• Many features are controlled from the menus using the menu navigation keys on
the remote control or the projector control panel.
For more information about using the menus, see later in this section, Using the
menus.
• Some of the menu features, for example brightness, contrast and sharpness,
can be accessed directly using the control keys at the bottom of the remote
control.
Notes
Page 44
Page 4.4 Rev D July 2014
4. Controlling the projector Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
The control panel
The projector control panel is designed to be read from the front or rear of the
projector, for ease of use.
The menu navigation keys are similar to those on the remote control, and are
described in detail in Using the menus, later in this section.
POWER Press this once to switch the projector ON or twice to switch it to
STANDBY mode.
SOURCE Press this repeatedly to cycle through the input sources, in the
following order:
HDMI 1, HDMI 2, RGB, Composite 1, Composite 2, Video,
S-Video, HDMI 1...
If you select a source that IS connected and active, the projector
will automatically adjust to the parameters of the signal, and
display it.
If you select a source that is NOT connected or active, the
projector will continue searching through the input sources until it
nds a valid signal.
LED status indicators
The indicators on the control panel are as follows:
POWER off = NO POWER steady blue = normal RUNNING mode
ashing blue = LAMP WARM-UP or COOL-DOWN mode
ISSUE off = NO ERROR ashing or steady red = ERROR
STANDBY amber = STANDBY mode
Notes
Many features are controlled
from the menus using the menu
navigation keys on the remote
control or the projector control
panel.
For more information about
using the menus, see later in
this section, Using the menus.
Always allow the lamp to cool
for 5 minutes before:
- moving the projector
- changing the lamp
If the red ISSUE indicator is
illuminated continuously or
ashing, see Error Codes in
section 6. Appendix, for more
information
Menu
navigation
keys
Page 45
Rev D July 2014 Page 4.5
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 4. Controlling the projector
The remote control
Layout
Timeout
There is a 5 second timeout for the control keys at the bottom of the remote control:
- after 5 seconds, if no adjustment has been made, the indicator will go out and
the adjustment key must be pressed again.
- to end the adjustment before 5 seconds has elapsed, press a different
adjustment key, or press the key again.
There is a 30 second timeout for the menu navigation keys.
Menu
navigation
keys
Control keys
Transmit
indicator
Notes
Many features are controlled
from the menus using the menu
navigation keys on the remote
control or the projector control
panel.
For more information about
using the menus, see later in
this section, Using the menus.
Some of the menu features,
for example brightness,
contrast and sharpness, can
be accessed directly using the
control keys at the bottom of
the remote control.
For more information about
using the control keys, see
later in this section, Using the
control keys.
In most situations, you can
simply point the remote control
at the screen which will reect
the IR signal from the remote
back toward the receiver on the
projector.
In some cases, however,
ambient conditions may prevent
this. In this case, point the
remote control directly at the
projector.
Remote reception angle
40°
40°
Page 46
Page 4.6 Rev D July 2014
4. Controlling the projector Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Notes
For more information about the
sources programmed into the
SOURCE keys, see Control
menu later in this section,
Using the menus.
For more information about
the Aspect ratio settings,
see Screen requirements in
section 2. Installation.
For more information about
the settings programmed into
the USER MEMORY keys,
see Control menu later in this
section.
Note: User memory D is
available only through the
Control menu.
Using the control keys
Power
• Press POWER ON on the remote control to switch the projector ON.
The power indicator on the control panel will ash blue for approximately 30
seconds, whilst the lamp comes up to full brightness. When the projector is
ready for use, the power indicator will show a steady blue.
• Press POWER OFF on the remote control to switch the projector to
STANDBY mode.
Press the button a second time to conrm your intention to switch to STANDBY
mode.
The lamp will switch off, and the power indicator on the control panel will ash
blue for approximately 30 seconds until the lamp has cooled down. Wait until
the power indicator has switched off and the standby indicator on the projector
control panel shows amber. The projector will now be in STANDBY mode.
Source
• To switch to one of the ve sources programmed into the SOURCE buttons, then
select using the to keys.
If you select a source that IS connected and active, the projector will
automatically adjust to the parameters of the signal, and display it.
If you select a source that is NOT connected or active, the projector will continue
searching through the input sources until it nds a valid signal, in this order.
HDMI 1, HDMI 2, RGB, Composite 1, Composite 2, Video, S-Video, HDMI 1...
Aspect ratio
• Press repeatedly to cycle through the Aspect ratio settings, in the
following order:
16:9, Theaterscope, 4:3, 4:3 Narrow, Native, 16:9...
User memory
• To switch to one of the three sets of image settings programmed into the USER
MEMORY buttons, then select using the or keys.
Page 47
Rev D July 2014 Page 4.7
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 4. Controlling the projector
Image quality settings
• Press any of the following keys on the remote control, followed by and , to
adjust these image quality settings:
Brightness
Contrast
Sharpness
Gamma
Overscan
Noise reduction
Colour temperature
Example - Brightness screen control:
Test pattern
• Press the key repeatedly to cycle through the Test patterns, in the
following order:
White, Black, Red, Green, Blue, Cyan, Magenta, Yellow, Chequerboard,
Greyscale, Alignment grid, White...
Lens
• Press the key repeatedly to cycle through the Lens adjustments, in the
following order:
Focus, Zoom, Shift...
• Use the use the , , and keys to adjust the lens.
Example - Lens Shift control:
Notes
For more information about all
these image quality settings,
and more, see Main menu and
Advanced menu later in this
section, Using the menus.
Some of the settings will not be
available for some of the input
sources.
Page 48
Page 4.8 Rev D July 2014
4. Controlling the projector Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Notes
Some menu controls can be
accessed directly using the
control keys (see earlier in this
section).
There is a 30 second timeout
for the menu navigation keys. If
a menu times out, simply press
the Menu key again.
The SELECT key on the
projector control panel has
exactly the same funtion as
the ENTER key on the remote
control.
To exit from the menus
completely, you may need to
press up to three times.
Using the menus
Navigating menus and submenus
The menus are organised into ve pages. When the menus are in use, the menu
page headings are always visible at the top of the menu panel.
Most menu items can be adjusted directly, but some items lead to a submenu.
The menus will always open at the same page that was last viewed. The example
below shows the rst menu page displayed following power on, which is always the
Main menu.
• Use the navigation keys on the remote control or the projector control panel to
navigate through the menus:
• To display the menus, press MENU on the remote control or the projector
control panel.
• To select a different menu page, use the and keys.
• To select a menu item, use the and keys.
• To close a menu, press MENU again.
Page 49
Rev D July 2014 Page 4.9
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 4. Controlling the projector
Notes
To select a different menu,
press MENU once or
twice, so that no items are
highlighted, then use the
and keys to select a
different page.
To exit from the menus
completely, you may need to
press up to three times.
Image changes made using
the menus will take effect
immediately.
Some menu items may be
greyed out - unavailable due to
the effect of settings made in
other menus, or due to the type
of input signal.
For more information about
the Aspect ratio settings,
see Screen requirements in
section 2. Installation.
Main menu
• To display the menus, press MENU on the remote control or the projector
control panel.
• Use the and keys to select the Main menu page,
• To select a menu item, use the and keys until the item is highlighted.
Aspect Ratio
• Use the and keys to select from:
16:9 the image is scaled to ll the DMD (and thus, a 16:9 screen).
Theaterscope the image is scaled such that a 2.35:1 image will be displayed
at the correct aspect ratio when the projector is tted with an
anamorphic lens. Thus an image with an aspect ratio of 2.35:1
can be displayed using the full 16:9 resolution of the DMD.
4:3 the image is scaled to t a 4:3 screen, using the full height of the
DMD.
4:3 Narrow to be used for 4:3 images in combination with an anamorphic
lens. The image is scaled to t the DMD vertically, but squeezed
horizontally such that the lens will stretch it to the correct ratio.
Native the image is displayed with no scaling, at its original resolution, in
the centre of the screen.
Page 50
Page 4.10 Rev D July 2014
4. Controlling the projector Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Presets
• Press ENTER or SELECT.
The Presets submenu will appear:
• Use the and keys to select from:
Recall Presets
Save Presets
Recall Presets
Recall a set of image settings that have previously been saved to Presets A, B,
C or D.
• Use the or keys to select which Preset is to be recalled.
• Select Default, to recall the factory default settings.
Save Presets
Save the the image settings for all seven inputs to the selected Preset.
• Use the or keys to select which Preset the settings will be saved to.
The following settings will be saved:
Brightness Contrast Saturation
Hue Sharpness Noise Reduction
Color Space Video Standard Gamma
Colour Temperature Color Gamut Brilliant Color
Adaptive Contrast RGB Offsets RGB Gains
Lamp Power
• To return to the Main menu, press once.
Notes
To select a different menu,
press MENU once or
twice, so that no items are
highlighted, then use the
and keys to select a
different page.
To exit from the menus
completely, you may need to
press up to three times.
Image changes made using
the menus will take effect
immediately.
The Presets can also be
recalled using the USER
MEMORY keys on the remote
control. See Using the control
keys earlier in this section.
Note: Preset D is available only
through the Control menu, not
through the remote control.
When Save Presets is
selected, the image settings for
ALL seven inputs are saved.
Main menu continued
Page 51
Rev D July 2014 Page 4.11
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 4. Controlling the projector
Brightness
• Press or once.
After the rst press, the Brightness adjustment bar will appear:
• Use the and keys to adjust the Brightness from 0 to 200:
• To return to the Main menu, press once.
Contrast
• Press or once.
After the rst press, the Contrast adjustment bar will appear.
• Use the and keys to adjust the Contrast from 0 to 200:
• To return to the Main menu, press once.
Saturation
Saturation is the amount of colour in the image. Decrease this setting if colors are
too bright; increase it if colors appear muted or washed out.
• Press or once.
After the rst press, the Saturation adjustment bar will appear.
• Use the and keys to adjust the Saturation from 0 to 200:
• To return to the Main menu, press once.
Hue
Hue is the ratio of red to green in the image. Decrease this setting to shift the hue
toward red; increase it to shift the hue toward green.
• Press or once.
After the rst press, the Hue adjustment bar will appear.
• Use the and keys to adjust the Hue from 0 to 200:
• To return to the Main menu, press once.
Notes
To exit from the menus
completely, you may need to
press up to three times.
Image changes made using
the menus will take effect
immediately.
Image changes made using
the menus will take effect
immediately.
Some menu items may be
greyed out - unavailable due to
the effect of settings made in
other menus, or due to the type
of input signal.
Image quality settings are often
interactive - a change in one
setting may require a change to
be made in another setting.
Setting Adaptive Contrast to
On in the Advanced menu will
affect any image quality settings
made in other menus.
Main menu continued
Page 52
Page 4.12 Rev D July 2014
4. Controlling the projector Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Notes
To exit from the menus
completely, you may need to
press up to three times.
Image changes made using
the menus will take effect
immediately.
Some menu items may be
greyed out - unavailable due to
the effect of settings made in
other menus, or due to the type
of input signal.
When the Aspect Ratio is set
to Native, Overscan can only
be set to Off or Crop
Sharpness
• Press or once.
After the rst press, the Sharpness adjustment bar will appear.
• Use the and keys to adjust the Sharpness from 0 to 200:
• To return to the Main menu, press once.
Noise Reduction
• Press or once.
After the rst press, the Noise reduction adjustment bar will appear.
• Use the and keys to adjust the Noise reduction from 0 to 200:
• To return to the Main menu, press once.
Overscan
Some television programs are produced based on the assumption that older
television sets may not display the outer edges of the broadcast picture area.
Consequently the edges of the image may be noisy or badly dened. Overscan is
used to compensate for this, by hiding the outer edges of the image.
• Use the or keys to select from:
Off
Crop blanks a 3% border from the left and right edges of the image
Zoom increases the horizontal and vertical resolution of the displayed
image by 6%, so that the all four edges fall outside the screen
area
Main menu continued
Page 53
Rev D July 2014 Page 4.13
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 4. Controlling the projector
Input Select
• Press ENTER or SELECT.
The Input select submenu will appear:
• Use the and keys to select from:
HDMI 1
HDMI 2
RGB
Component 1
Component 2
Video
S-Video
• Press ENTER or SELECT, to select a different input source.
• To return to the Main menu, press once.
Resync
If the image has become unstable or degraded, it may be possible to improve the
display:
• Press ENTER or SELECT.
The projector will attempt to re-synchronise to the current input source.
Notes
To select a different menu,
press MENU once or
twice, so that no items are
highlighted, then use the
and keys to select a
different page.
To exit from the menus
completely, you may need to
press up to three times.
Image changes made using
the menus will take effect
immediately.
Some menu items may be
greyed out - unavailable due to
the effect of settings made in
other menus, or due to the type
of input signal.
If you select a source that IS
connected and active, the
projector will automatically
adjust to the parameters of the
signal, and display it.
If you select a source that is
NOT connected or active, the
projector will continue searching
through the input sources until it
nds a valid signal, in this order.
HDMI 1, HDMI 2, RGB,
Composite 1, Composite 2,
Video, S-Video, HDMI 1...
Main menu continued
Page 54
Page 4.14 Rev D July 2014
4. Controlling the projector Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Notes
To select a different menu,
press MENU once or
twice, so that no items are
highlighted, then use the
and keys to select a
different page.
To exit from the menus
completely, you may need to
press up to three times.
Image changes made using
the menus will take effect
immediately.
Some menu items may be
greyed out - unavailable due to
the effect of settings made in
other menus, or due to the type
of input signal.
To determine what is the correct
colour space to use, consult
the user manual for the video
source.
Advanced menu
• To display the menus, press MENU on the remote control or the projector
control panel.
• Use the and keys to select the Advanced menu page,
• To select a menu item, use the and keys until the item is highlighted.
Colour Space
In most cases, the Auto setting will determine the correct color space to use. If it
does not, you can select the appropriate setting manually.
• Use the and keys to select from:
Auto
YPbPr
YCbCr
RGB-PC
RGB Video
Page 55
Rev D July 2014 Page 4.15
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 4. Controlling the projector
Video Standard
In most cases, the Auto setting will determine the correct video standard to use. If it
does not, you can select the appropriate setting manually.
• Use the and keys to select from:
Auto
NTSC used mainly in the United States and Japan
PAL used in Europe, Australia and many other parts of the world,
typically with a 50Hz frame rate
SECAM used mainly in France and Russia
Gamma
Video recordings are often supplied with a gamma adjustment applied. The
projector’s gamma setting can be used to correct for this. If you are unsure, then
choose a setting that gives a decent level of contrast, whilst maintaining good detail
in the darkest and lightest areas of the image.
• Use the and keys to select from:
CRT gamma of 2.5
Film gamma of 2.2
Video similar to Film but improves the dark areas of the image -
especially suitable for images from video cameras
Punch enhanced brightness and increased colour saturation for high
ambient light environments
Graphics enhanced highlights and contrast, especially suitable for computer
presentations
Notes
To exit from the menus
completely, you may need to
press up to three times.
Image changes made using
the menus will take effect
immediately.
Some menu items may be
greyed out - unavailable due to
the effect of settings made in
other menus, or due to the type
of input signal.
Image quality settings are often
interactive - a change in one
setting may require a change to
be made in another setting.
Advanced menu continued
Page 56
Page 4.16 Rev D July 2014
4. Controlling the projector Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Colour Temperature
In general, a higher colour temperature gives a cooler feeling to the image, and a
lower temperature gives a warmer feeling.
• Press ENTER or SELECT to see the Color Temperature submenu:
• Use the and keys to select from:
5500K
6500K
7500K
9300K
Native
ColorMAX User 1 Applies the Colour Temperature settings made externally
using the DP Userware on a personal computer
ColorMAX User 2 Applies the Colour Temperature settings made externally
using the DP Userware on a personal computer
Notes
To exit from the menus
completely, you may need to
press up to three times.
Image changes made using
the menus will take effect
immediately.
Some menu items may be
greyed out - unavailable due to
the effect of settings made in
other menus, or due to the type
of input signal.
Advanced menu continued
Page 57
Rev D July 2014 Page 4.17
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 4. Controlling the projector
Notes
To exit from the menus
completely, you may need to
press up to three times.
Image changes made using
the menus will take effect
immediately.
Some menu items may be
greyed out - unavailable due to
the effect of settings made in
other menus, or due to the type
of input signal.
It is best to turn the Dynamic
Black setting Off before
adjusting the brightness.,
contrast or image quality
settings.
Setting Adaptive Contrast to
On will affect any image quality
settings made in other menus.
Colour Gamut
In most cases, the Auto setting will determine the correct colour gamut to use. If it
does not, you can select the appropriate setting manually.
Each setting denes the precise hue of each primary (red, green and blue) and
secondary (yellow, cyan and magenta) color component used to generate the
image.
• Press ENTER or SELECT to see the Color Gamut submenu (similar to the
Color Temperature menu shown on the previous page).
• Use the and keys to select from:
Auto
SMPTE-C for NTSC, 480i and 480p sources
EBU for PAL, SECAM, 576i and 576p sources
REC709 for most other sources
Native uncorrected
ColorMAX User 1 Applies the User gamma settings made externally using
the DP Userware on a personal computer
ColorMAX User 2 Applies the User gamma settings made externally using
the DP Userware on a personal computer
Dynamic Black®
Dynamic Black® allows for increased contrast by adjusting the black level of the
image, depending on the overall brightness of the image.
• Use the and keys to select from:
On
Off
Adaptive Contrast
Adaptive Contrast expands the light and dark portions of the contrast curve of the
image, depending on the mean luminance of the image.
• Use the and keys to select from:
On
Off
Advanced menu continued
Page 58
Page 4.18 Rev D July 2014
4. Controlling the projector Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Notes
To select a different menu,
press MENU once or
twice, so that no items are
highlighted, then use the
and keys to select a
different page.
To exit from the menus
completely, you may need to
press up to three times.
Image changes made using
the menus will take effect
immediately.
Some menu items may be
greyed out - unavailable due to
the effect of settings made in
other menus, or due to the type
of input signal.
A good way to carry out tracking
and phase adjustments is to
use the grey scale test pattern.
Always adjust the tracking
before adjusting the phase
Fine Sync
• Press ENTER or SELECT.
The Fine Sync submenu will appear:
• Use the and keys to select from:
V Position ne tunes the vertical position of the image
H Position ne tunes the horizontal position of the image
Tracking adjusts the frequency of the pixel sampling clock, so that all pixels
generated by the video source are sampled. Steady ickering
or several soft vertical stripes or bands across the entire image
indicate poor pixel tracking.
Phase adjusts the phase of the pixel sampling clock relative to the
incoming signal. Adjust the phase when an RGB or Component
image still shows shimmer or noise after the tracking has been
optimized.
Sync Level adjusts the voltage level of the projector’s sync signal detection
circuitry. Sync Level adjustment is occasionally necessary when
a signal source signal drops “below black” (for example, during
scenes with explosions or when subtitles are present) and causes
the projector to temporarily lose sync.
• Use the and keys to adjust the setting from 0 to 200.
• To return to the Advanced menu, press once.
Advanced menu continued
Page 59
Rev D July 2014 Page 4.19
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 4. Controlling the projector
RGB Adjust
• Press ENTER or SELECT.
The RGB Adjust submenu will appear:
Use the Gain controls to correct color imbalances in the bright areas of the image.
Use the Offset controls in the RGB Adjust sub-menu to correct color imbalances in
the dark areas of the image.
• Use the and keys to select from:
Red Offset
Blue Offset
Green Offset
Red Gain
Blue Gain
Green Gain
Offsets
• Use the and keys to adjust the Offset from 0 to 200.
Gains
• Use the and keys to adjust the Gain from 0 to 200.
• To return to the Advanced menu, press once.
Advanced menu continued
Notes
To select a different menu,
press MENU once or
twice, so that no items are
highlighted, then use the
and keys to select a
different page.
To exit from the menus
completely, you may need to
press up to three times.
Image changes made using
the menus will take effect
immediately.
Some menu items may be
greyed out - unavailable due to
the effect of settings made in
other menus, or due to the type
of input signal.
A good way to carry out this
adjustment is to use the
chequerboard test pattern.
RGB settings are interactive
- a change in one setting may
require a change to be made in
the other.
Page 60
Page 4.20 Rev D July 2014
4. Controlling the projector Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
System menu
• To display the menus, press MENU on the remote control or the projector
control panel.
• Use the and keys to select the System menu page,
• To select a menu item, use the and keys until the item is highlighted.
Language
This product is available only in English at present.
Notes
To select a different menu,
press MENU once or
twice, so that no items are
highlighted, then use the
and keys to select a
different page.
To exit from the menus
completely, you may need to
press up to three times.
Page 61
Rev D July 2014 Page 4.21
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 4. Controlling the projector
Source Enable
• Press ENTER or SELECT.
The Source Enable submenu will appear:
• Use the and keys to select from:
HDMI 1
HDMI 2
RGB
Component 1
Component 2
Video
S-Video
• For each source, use the and keys to select from:
On the selected source will be included in an automatic input source
search
Off the selected source will not be included in an automatic input
source search
• To return to the System menu, press MENU once.
System menu continued
Notes
To select a different menu,
press MENU once or
twice, so that no items are
highlighted, then use the
and keys to select a
different page.
To exit from the menus
completely, you may need to
press up to three times.
Page 62
Page 4.22 Rev D July 2014
4. Controlling the projector Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Menu Position
• Use the and keys to select from:
Top left
Top right
Bottom left
Bottom right
Centre
Blank Screen
This option determines what appears on screen when the projector is searching for
a valid input source.
• Use the and keys to select from:
Digital Projection logo
Black screen
Blue screen
White screen
Auto Power On
• Use the and keys to select from:
On When power is connected, the projector starts up imediately.
Off When power is connected, the projector goes into Standy mode,
and does not start until POWER ON on the remote control
or POWER on the projector control panel is pressed.
Auto Power Off
When the projector is searching for a valid input source, this option determines what
appears on screen.
• Use the and keys to select from:
On The projector automatically goes into Standby mode if no input
source is detected for 20 minutes.
Off The projector stays on until POWER OFF on the remote
control or POWER on the projector control panel is pressed.
Notes
To exit from the menus
completely, you may need to
press up to three times.
Image changes made using
the menus will take effect
immediately.
System menu continued
Page 63
Rev D July 2014 Page 4.23
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 4. Controlling the projector
Lamp Power
In Economy mode, the lamp will be run at approximately 20% lower power level.
This will prolong the life of the lamp, but decrease brightness.
• Use the and keys to select from:
Economy
Standard
Rear Projection
• Use the and keys to select from:
On Projected image is reversed, left to right
Off
Ceiling Mode
• Use the and keys to select from:
On Projected image is reversed, top to bottom
Off
Logo Display
• Use the and keys to select from:
On The Digital Projection logo is displayed during power up
Off
Notes
The Lamp Power setting will
be saved with the other user
settings when Save Presets is
used.
For more information about
Presets, see Main Menu, earlier
in this section.
To exit from the menus
completely, you may need to
press up to three times.
Image changes made using
the menus will take effect
immediately.
System menu continued
Page 64
Page 4.24 Rev D July 2014
4. Controlling the projector Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Notes
To select a different menu,
press MENU once or
twice, so that no items are
highlighted, then use the
and keys to select a
different page.
To exit from the menus
completely, you may need to
press up to three times.
Once the IR Sensor has been
disabled, it can be re-enabled
by using the control keys, or by
sending a remote command via
RS232 or LAN.
For more information about
remote commands, see
Remote communications
protocol in section
6. Appendix.
Control menu
• To display the menus, press MENU on the remote control or the projector
control panel.
• Use the and keys to select the Control menu page,
• To select a menu item, use the and keys until the item is highlighted.
IR Sensor
• Use the and keys to select from:
On the remote control is enabled
Off the remote control is disabled
Projector Control
• Use the and keys to select from:
Network the projector can be controlled by remote commands from the
LAN input
RS232 the projector can be controlled by remote commands from the
RS232 input
Page 65
Rev D July 2014 Page 4.25
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 4. Controlling the projector
Control menu continued
Notes
To select a different menu,
press MENU once or
twice, so that no items are
highlighted, then use the
and keys to select a
different page.
To exit from the menus
completely, you may need to
press up to three times.
Lens Control
• Press ENTER or SELECT.
The Lens submenu will appear:
• Use the and keys to select from:
Focus
Zoom
Lens Shift
• Press ENTER or SELECT to activate the lens control.
• Use the use the , , and keys to adjust the lens.
Example - Lens Shift control:
Page 66
Page 4.26 Rev D July 2014
4. Controlling the projector Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Notes
To select a different menu,
press MENU once or
twice, so that no items are
highlighted, then use the
and keys to select a
different page.
To exit from the menus
completely, you may need to
press up to three times.
If a source has been disabled in
the System menu, then a key
programmed with that source
will have no effect.
Keys 1 to 5
The to keys on the remote control can each be programmed to switch
to one of the seven input sources.
• Use the and keys to select a Key, then press ENTER or SELECT.
The Key submenu will appear:
• Use the and keys to select from:
HDMI 1
HDMI 2
RGB
Component 1
Component 2
Video
S-Video
• Press ENTER or SELECT to conrm your selection.
• Press MENU to return to the Control menu and select another key.
Control menu continued
Page 67
Rev D July 2014 Page 4.27
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 4. Controlling the projector
Trigger 1 & 2
The Trigger 1 and Trigger 2 outputs are interchangeable:
Screen trigger: can be connected to an electrically operated screen,
automatically deploying the screen when the projector
starts up, and retracting the screen when the projector
shuts down.
Aspect Ratio trigger: can be used to control screen shuttering for different
aspect ratios
• For each Trigger setting, use the and keys to select from:
Screen trigger occurs when the projector is in RUNNING mode
16:9 trigger occurs when 16:9 aspect ratio is selected
Theaterscope trigger occurs when Theaterscope aspect ratio is selected
4:3 trigger occurs when 4:3 aspect ratio is selected
4:3 Narrow trigger occurs when 4:3 Narrow aspect ratio is selected
RS232 trigger output follows the On or Off setting specied in a trig.1 or
trig.2 command received from a PC via the LAN or RS232 serial
input.
Auto Source
• Use the and keys to select from:
On projector searches for an alternative input source when the current
input source is disconnected
Off projector shows a ‘blank’ screen when the current input source is
disconnected.
Control menu continued
Notes
To select a different menu,
press MENU once or
twice, so that no items are
highlighted, then use the
and keys to select a
different page.
To exit from the menus
completely, you may need to
press up to three times.
For more information about
the trigger output, see Control
connections in section
6. Appendix.
To set what a ‘blank’ screen
looks like, use the Blank
Screen setting in the System
menu.
Page 68
Page 4.28 Rev D July 2014
4. Controlling the projector Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Notes
To select a different menu,
press MENU once or
twice, so that no items are
highlighted, then use the
and keys to select a
different page.
To exit from the menus
completely, you may need to
press up to three times.
Restore Defaults will restore
all settings to factory
defaults.
If you are not sure this is
what you want to do, then
either:
make a record of all settings
rst
or
select No, then press ENTER or
SELECT
Service menu
• To display the menus, press MENU on the remote control or the projector
control panel.
• Use the and keys to select the Service menu page,
The rst eight items are for information only, and cannot be changed.
• To select a menu item, use the and keys until the item is highlighted.
Factory Reset
• Press ENTER or SELECT to request a Factory Reset.
The following message will be displayed.
• Use the and keys to select from:
Yes all settings will be restored to factory defaults
No
Press ENTER or SELECT to conrm your choice.
Page 69
Rev D July 2014 Page 4.29
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 4. Controlling the projector
Blue Only
This is useful for color-calibrating the projector or other video components.
• Use the and keys to select from:
On only the blue signal is displayed - green and red are turned off
Off all three signals - red, green and blue - are displayed
Test Patterns
• Use the and keys to select from:
Test Pattern Off
White
Black
Red
Green
Blue
Cyan
Magenta
Yellow
Chequerboard
Greyscale
Alignment grid
• To turn the test pattern Off, press any other key.
Altitude
For use at high altitudes where the air is thinner, the fan speed can be increased.
• Use the and keys to select from:
Low normal speed fan
High high speed fan
Notes
To exit from the menus
completely, you may need to
press up to three times.
Image changes made using
the menus will take effect
immediately.
Some menu items may be
greyed out - unavailable due to
the effect of settings made in
other menus, or due to the type
of input signal.
If the projector frequently
overheats when used in a high
altitude environment, then
it may help to use the High
Altitude setting.
In most cases, the Low Altitude
setting should be satisfactory.
Service menu continued
Page 70
Page 4.30 Rev D July 2014
4. Controlling the projector Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Page 71
Rev D July 2014 Page 5.1
5. Maintenance
Contents
Changing the lamp module .............................................................................................................. 5.2
Cleaning the fans ................................................................................................................................ 5.3
Cleaningorreplacingtheairlter .................................................................................................. 5.4
Page 72
Page 5.2 Rev D July 2014
5. Maintenance Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Changing the lamp module
• Turn the power OFF and allow the lamp to cool for 5 minutes.
• Unscrew the captive nger screw securing the lamp door, and remove the door.
• Unscrew the two cross-head screws securing the lamp module to the projector
• Lift the wire handle up and use it to pull out the lamp module.
• Fit a new lamp module, pushing it rmly into place.
• Tighten the two cross-head screws.
• Locate the two lugs at the bottom of the lamp door into the slots, and re-t the
door. Tighten the nger screw.
Notes
Always allow the lamp to cool
for 5 minutes before:
- disconnecting the power
- moving the projector
- changing the lamp
There are no user-serviceable
parts inside the lamp module.
The whole module should be
replaced.
Only lamps supplied by
Digital Projection and
intended for this projector
should be used. Fitting any
other lamp could damage
both projector and lamp, and
will invalidate the warranty.
At the end of life, the lamp
will not strike, and the Issue
indicator on the control panel
will ash red. (Typical lamp life
is 2000 hours)
Do not use the lamp for more
than 2000 hours, as this may
cause serious lamp failure,
damage the lamp module
and cause extra cost on
replacement.
Take care not to touch the
glass surface of the lamp
module. If you do accidentally
touch the glass, it should be
cleaned before use.
HID lamps produce high
intensity light. Do not look
directly at the light coming
from the lamp housing or the
lens.
Opening the lamp door will
switch the projector OFF. The
projector cannot be operated
until the door is fully closed.
Page 73
Rev D July 2014 Page 5.3
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 5. Maintenance
Cleaning the fans
• Turn the power OFF and wait until the fans stop.
• Use a vacuum cleaner to clean the inlet and outlet fans, as shown below.
Notes
Always switch the projector
OFF before cleaning the fans.
Always allow the lamp to cool
for 5 minutes before:
- disconnecting the power
- moving the projector
- changing the lamp
- cleaning the fans and lter
The fans should be cleaned
regularly:
• In a clean environment such as
an ofce, after 500 hours.
• In a dusty or smoky
environment such as a theatre
or public area, more frequent
cleaning may be necessary.
Page 74
Page 5.4 Rev D July 2014
5. Maintenance Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Cleaningorreplacingtheairlter
• Turn the power OFF and allow the lamp to cool for 5 minutes.
• Unscrew the two cross-head screws securing the lter cover to the projector
• Remove the cover and the lter.
• Clean the lter using clean water, or replace it with a new lter.
• Allow the lter to dry before reuse.
• Replace the lter, pushing it rmly into place.
• Ret the lter cover.
Notes
Always switch the projector
OFFbeforecleaningthelter.
Always allow the lamp to cool
for 5 minutes before:
- disconnecting the power
- moving the projector
- changing the lamp
- cleaning the fans and lter
The lter should be cleaned
regularly:
• In a clean environment such as
an ofce, after 500 hours.
• In a dusty or smoky
environment such as a theatre
or public area, more frequent
cleaning may be necessary.
Allow the lter to dry before
reuse.
If the lter is broken, then
replace it.
Page 75
Rev D July 2014 Page 6.1
6. Appendix
Contents
Troubleshooting .................................................................................................................................. 6.2
Error codes ...................................................................................................................................... 6.4
Dimensions .......................................................................................................................................... 6.5
Specications ...................................................................................................................................... 6.6
Part numbers .................................................................................................................................... 6.6
Optical ............................................................................................................................................. 6.6
Electrical .......................................................................................................................................... 6.7
Physical ........................................................................................................................................... 6.7
Video formats supported ................................................................................................................ 6.10
Input connections ............................................................................................................................. 6.12
HDMI 1 & 2 inputs ........................................................................................................................... 6.12
Composite video input ..................................................................................................................... 6.12
S-Video input .................................................................................................................................. 6.12
RGB input ...................................................................................................................................... 6.13
Component 1 input .......................................................................................................................... 6.13
Component 2 input .......................................................................................................................... 6.13
Control connections ........................................................................................................................ 6.14
Wired Remote control connection ..................................................................................................... 6.14
Trigger 1 & 2 output ........................................................................................................................ 6.14
Serial control input .......................................................................................................................... 6.14
Null-modem cable ......................................................................................................................... 6.14
Serial port settings ........................................................................................................................ 6.14
Remote communications protocol ............................................................................................... 6.16
Introduction .................................................................................................................................... 6.16
Key Commands .............................................................................................................................. 6.16
Example ..................................................................................................................................... 6.16
The commands ............................................................................................................................ 6.16
Operation Commands ..................................................................................................................... 6.18
Example ..................................................................................................................................... 6.18
The commands ............................................................................................................................ 6.18
Setting the LAN IP conguration ....................................................................................................... 6.23
Page 76
Page 6.2 Rev D July 2014
6. Appendix Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Troubleshooting
Problem Possible solutions
The red ISSUE indicator is illuminated
continuouslyorashing.
Check the Error codes detailed on the next page.
The projector will not power up. Check that the mains plug is plugged in and that the mains supply is switched on.
Check that the lamp door is closed properly.
Check any external fuses or breakers.
The projector will not power up shortly
after being switched off.
To protect the lamp, the projector cannot be switched on when in it is in cool-down
mode. Wait until the power indicator stops ashing blue, and the standby indicator
shows amber.
The projector shuts down after it has
been in use for some time.
The projector may be overheating. Check that the air inlets and outlets are clear
of any obstruction.
See section 5. Maintenance
It is possible to increase the speed of the fans for use in a high altitude
environment:
See section 4. Controlling the projector, System menu
No image is displayed. See section 5. Maintenance, Changing the lamp
Check that the input source is switched on and connected to the projector
correctly.
Check that the correct image source is selected.
Check that the brightness and contrast settings are set correctly.
See section 4. Controlling the projector, Using the control keys and Main
menu
The projector may be overheating. Check that the air inlets and outlets are clear
of any obstruction.
Theimagedoesnottthescreen
correctly.
Check that the projector and screen size are positioned correctly, and that the
zoom is adjusted correctly.
See section 2. Installation, Screen size vs throw distance
Check the aspect ratio setting.
See section 4. Controlling the projector, Main menus
Uneven image quality. Check that the projector is parallel to the screen.
Check that the screen is at, and securely mounted.
Page 77
Rev D July 2014 Page 6.3
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 6. Appendix
Problem Possible solutions
Image is split or otherwise scrambled. Check that the image source is not set to progressive scan.
Image is blurred. Check that the lens is focussed correctly.
Image is too bright, and lacks
denitioninthebrightareas.
Decrease the contrast setting.
See section 4. Controlling the projector, Using the control keys and Main
menu
Image appears ‘washed out’ and is too
bright in the dark areas
Decrease the brightness setting.
See section 4. Controlling the projector, Using the control keys and Main
menu
Colors in the image are swapped.
for example, reds appear blue or vice
versa.
Check that the Component signals are connected correctly.
See Section 4. Installation, Connecting the projector.
Projector does not respond to control
commands from a computer.
Check that the LAN or serial cable is connected correctly.
Check that the baud rate is set correctly (if using a serial cable).
See this section 6. Appendix, Connections
Check the Projector Control setting in the Control Menu.
See section 4. Controlling the projector, Control menu
Check that the correct control codes are being used.
See this section 6. Appendix. Serial communications protocol
Projector does not respond to control
commands from the remote control.
Check that the infra red windows at the front and rear of the projector or on the IR
repeater are not obstructed. Check that the batteries are in good condition.
If you are using an IR repeater, check that the cable is connected properly at both
ends, and that the cable is not damaged.
See section 4. Controlling the projector, The remote control
Check the IR Sensor setting in the Control Menu.
See section 4. Controlling the projector, Control menu
In the event that this troubleshooting guide has not solved the problem,
then contact your Digital Projection dealer or service centre.
Page 78
Page 6.4 Rev D July 2014
6. Appendix Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Error codes
If the projector detects an error, the red Issue indicator will ash, as shown in the
chart below.
For example, if the lamp door is left open, the red indicator will ash twice followed
by a pause, then the sequence will repeat until the error condition is corrected.
Notes
Page 79
Rev D July 2014 Page 6.5
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 6. Appendix
Dimensions
All dimensions in mm
unless otherwise stated
Page 80
Page 6.6 Rev D July 2014
6. Appendix Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Specications
Part numbers
Projector
Highlite 260 HB 110-509
Highlite 260 HC 110-016
HIGHlite 1080p 330 110-748
Power cable 10A, Europe 102-163
Power cable 13A, North America 102-165
Power cable 10A, United Kingdom 102-180
Remote control 110-024
User manual on CD 111-368
Important Information 111-369
Getting Started Guide 111-370
Replacement parts
Lamp module 260 HB, HC: 110-025
1080p 330: 111-100
Air lter 111-400
Lenses High Brightness High Contrast
0.77 : 1 xed lens 110-808 110-022
1.16 : 1 xed lens 110-809 110-023
1.45 - 1.74 : 1 zoom lens 110-803 110-017
1.74 - 2.17: 1 zoom lens 110-804 110-018
2.17 - 2.9: 1 zoom lens 110-805 110-019
2.9 - 4.34: 1 zoom lens 110-806 110-020
4.34 - 6.76: 1 zoom lens 110-807 110-021
Optical
Digital Light Processor 3 x 0.65” Texas Instruments DMD™, resolution 1920 x 1080 pixels
Contrast Ratio 260 HC: 20000:1 ±10% (with HC lens and Dynamic Black)
260 HB, 1080p 330: 2000:1 ±10%
Colour temperature Native: 6500K (±1500K), adjustable: 5500K - 9300K
Pixelllfactor 87%
Lamp power 260HB, HC: 260W
1080p 330: 330W
Lamp life (typical) 2000 hours
Brightness 260 HC: 2000 ANSI lumens ±10%
260 HB: 3500 ANSI lumens ±10%
1080p 330: 6000 ANSI lumens ±10%
Uniformity 80%
Page 81
Rev D July 2014 Page 6.7
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 6. Appendix
Electrical
Inputs HDMI x 2, RGB, Component x 2, Video, S-Video
Pixel clock (digital) up to 165MHz
Bandwidth (analog) 200MHz
Control inputs 1 x LAN
1 x RS232 serial: 38400 baud, 8 bits, 1 stop bit, no parity
1 x remote control
Indicators Power, Standby, Issue (Fault)
Mains voltage 100-240 VAC ±10%, 47-63Hz (single phase)
Power consumption 260 HB, HC: 450W max, <2W in Standby (LAN off)
1080p 330: 500W max, <2W in Standby (LAN off)
International Regulations Meets FCC Class B requirements
Meets EMC Directives (EN 55022, EN 55024)
Meets Low Voltage Directive (EN60950)
Physical
Temperature
Operating 10 to 35°C
Storage -20 to 60°C
Thermal Dissipation 260 HB, HC: 1536 BTU/hr max
1080p 330: 1706 BTU/hr max
Humidity
Operating 20% to 90% non condensing
Storage 10% to 90%
Altitude
Operating up to 3,000 m (10,000 feet)
Storage up to 12,000 m (40,000 feet)
Weight 20 kg (44 lbs)
Noise level < 35 dB
Specications are subject to change without notice.
Page 82
Page 6.8 Rev D July 2014
6. Appendix Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Lens Data
Optical 110-022 ~ 110-808 110-023 ~ 110-809 110-017 ~ 110-803 110-018 ~ 110-804
throw ratio 0.77:1xed 1.16:1xed 1.45 - 1.74 :1 zoom 1.74 - 2.17 : 1 zoom
full DMD image width 0.77 : 1
1.69 - 3.25m
(5.5 - 10.7ft)
1.16 : 1
1.21 - 5.34m
(4 - 17.5ft)
1.45 : 1
1.24 - 5.24m
(4.1 - 17.2ft)
1.74 : 1
1.26 - 5.34m
(4.1 - 17.5ft)
1.74 : 1
1.26 - 5.46m
(4.1 - 17.9ft)
2.17 : 1
1.24 - 5.44m
(4.1 - 17.8ft)
throw distance 0.77 : 1
1.3 - 2.5m
(4.3 - 8.2ft)
1.16 : 1
1.4 - 6.2m
(4.6 - 20.3ft)
1.45 : 1
1.8 - 7.6m
(5.9 - 24.9ft)
1.74 : 1
2.2 - 9.3m
(7.2 - 30.5ft)
1.74 : 1
2.2 - 9.5m
(7.2 - 31.2ft)
2.17 : 1
2.7 - 11.8m
(8.9 - 38.7ft)
lens shift vertical *
pixels (vs DMD height)) (%)
± 216
(± 0.2H) (40%)
± 216
(± 0.2H) (40%)
± 648
(± 0.6H) (120%)
± 648
(± 0.6H) (120%)
lens shift horizontal *
pixels (vs DMD width) (%)
± 96
(± 0.05W) (10%)
± 96
(± 0.05W) (10%)
± 288
(± 0.15W) (30%)
± 288
(± 0.15W) (30%)
Aperture F/2.5 F/2.5 F/2.5 F/2.5
Max object eld size 20.1mm
(0.79”)
20.1mm
(0.79”)
26.4 mm
(1.04”)
26.4 mm
(1.04”)
Effective focal length 11.6mm
(0.46in)
17.1mm
(0.67in)
21.2 - 25.8mm
(0.83 - 1.02in)
25.5 - 32.0mm
(1.0 - 1.26in)
Distortion <035% <0.3% <0.5% <0.5%
Transmission >85% >85% >85% >85%
Mechanical
Lens extension**
(±2%)
80 mm
(3.2 in)
54 mm
(2.1 in)
24 mm
(1.0 in)
0
Weight
±0.05 kg (±0.1lb)
2.42 kg
(5.3 lb)
1.86 kg
(4.1 lb)
1.90 kg
(4.2 lb)
1.47 kg
(3.2 lb)
lens extension, measured
from front of projector
* Actual available lens shift is reduced when the lens is to be shifted
in two directions combined (see Shifting the image, in section
2. Installation).
** Lens extension is the distance from the outer end of the lens to the
front of the projector. It is important for calculating throw distance
accurately (see Useful lens calculations, in section 2. Installation).
Page 83
Rev D July 2014 Page 6.9
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 6. Appendix
Optical 110-019 ~ 110-805 110-020 ~ 110-806 110-021 ~ 110-807
throw ratio 2.17 - 2.9 : 1 zoom 2.9 - 4.34 : 1 zoom 4.34 - 4.16 : 1 zoom
full DMD image width 2.17 : 1
1.24 - 5.3m
(4.1 - 17.4ft)
2.9 : 1
1.28 - 5.31m
(4.2 - 17.4ft)
2.9 : 1
1.24 - 5.07m
(4.1 - 16.6ft)
4.34 : 1
1.27 - 5.18m
(4.2 - 17ft)
4.34 : 1
1.27 - 5.07m
(4.2 - 16.6ft)
6.76 : 1
1.27 - 5.18m
(4.2 - 17ft)
throw distance 2.17 : 1
2.7 - 11.5m
(8.9 - 37.7ft)
2.9 : 1
3.7 - 15.4m
(12.1 - 50.5ft)
2.9 : 1
3.6 - 14.7m
(11.8 - 48.2ft)
4.34 : 1
5.5 - 22.5m
(18 - 73.8ft)
4.34 : 1
5.5 - 22m
(18 - 72.2ft)
6.76 : 1
8.6 - 35m
(28.2 - 114.8ft)
lens shift vertical *
pixels (vs DMD height)) (%)
± 648
(± 0.6H) (120%)
± 648
(± 0.6H) (120%)
± 648
(± 0.6H) (120%)
lens shift horizontal *
pixels (vs DMD width) (%)
± 288
(± 0.15W) (30%)
± 288
(± 0.15W) (30%)
± 288
(± 0.15W) (30%)
Aperture F/2.5 F/2.5 F/2.5
Max object eld size 26.4 mm
(1.04”)
26.4 mm
(1.04”)
26.4 mm
(1.04”)
Effective focal length 31.9 - 42.5mm
(1.26 - 1.67in)
40.8 - 62.8mm
(1.61 - 2.48in)
62.1- 97.8mm
(2.44 - 3.85in)
Distortion <0.5% <0.5% <0.5%
Transmission > 85 % > 85 % > 85 %
Mechanical
Lens extension**
(±2%)
0 0 0
Weight
±0.05 kg (±0.1lb)
1.49 kg
(3.3 lb)
1.52 kg
(3.3 lb)
1.48 kg
(3.3 lb)
lens extension, measured
from front of projector
* Actual available lens shift is reduced when the lens is to be shifted
in two directions combined (see Shifting the image, in section
2. Installation).
** Lens extension is the distance from the outer end of the lens to the
front of the projector. It is important for calculating throw distance
accurately (see Useful lens calculations, in section 2. Installation).
Page 84
Page 6.10 Rev D July 2014
6. Appendix Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Video formats supported
Signal Type Resolution
Frame
Rate
HDMI
RGB
Component 1:
RGB
Component 1:
Y/Pr/Pb Y/Cr/Cb
Component 2:
Y/Pr/Pb Y/Cr
Video
S-Video
Reference
PC 640x480 59.94 x x x VESA DMT
640x480 74.99 x x x VESA DMT
640x480 85 x x x VESA DMT
800x600 60.32 x x x VESA DMT
800x600 75 x x x VESA DMT
800x600 85.06 x x x VESA DMT
848x480 47.95 x x x VESA CVT
848x480 59.94 x x x VESA CVT
1024x768 60 x x x VESA DMT
1024x768 75.03 x x x VESA DMT
1024x768 85.03 x x x VESA DMT
1024x768 70.1 x x x VESA DMT
1280x720 47.95 x x x VESA GTF
1280 x 768 60 x x x VESA DMT
1280 x 768 60 x x x VESA DMT Reduced Blanking
1280 x 768 75 x x x VESA DMT
1280 x 768 85 x x x VESA DMT
1280 x 800 50 x x x VESA DMT
1280 x 800 60 x x x VESA DMT
1280 x 800 75 x x x VESA DMT
1280x1024 60.02 x x x VESA DMT
1280x1024 75.02 x x x VESA DMT
1280x1024 85.02 x x x VESA DMT
1440 x 900 60 x x x VESA DMT
1440 x 900 75 x x x VESA DMT
1400 x 1050 60 x x x VESA DMT
1400 x 1050 75 x x x VESA DMT
1600x1200 60 x x x VESA DMT
1920x1080 47.95 x x x VESA CVT
1600 x 1200 60 x x x VESA DMT
1920 x 1200 60 x x x VESA DMT Reduced Blanking
1680x1050 59.94 x x x VESA CVT
Apple Mac 640x480 66.59 x x x VESA DMT
832x624 74.54 x x x VESA DMT
Page 85
Rev D July 2014 Page 6.11
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 6. Appendix
Signal Type Resolution
Frame
Rate
HDMI
RGB
Component 1:
RGB
Component 1:
Y/Pr/Pb Y/Cr/Cb
Component 2:
Y/Pr/Pb Y/Cr
Video
S-Video
Reference
NTSC NTSC (M, 4.43) 59.94 x x ITU-R BT.1700, SMPTE 170M
PAL PAL (B,G,H,I) 50 x x ITU-R BT.1700
PAL (N) 50 x x ITU-R BT.1700
PAL (M) 59.94 x x ITU-R BT.1700
SECAM SECAM (M) 50 x x ITU-R BT.1700
480i 59.94 x x x SMPTE 125M, CEA-861-D
576i 50 x x x ITU-R BT.601, CEA-861-D
EDTV 480p 59.94 x x x x x SMPTE 293M, CEA-861-D
576p 50 x x x x x ITU-R BT.1358, CEA-861-D
HDTV 1035i 60 x x x x x SMPTE 260M
1080i 50 x x x x x SMPTE 274M, CEA-861-D
1080i (Aus) 50 x x x x x SMPTE 295M
1080i 59.94 x x x x x SMPTE 274M, CEA-861-D
1080i 60 x x x x x SMPTE 274M, CEA-861-D
720p 50 x x x x x SMPTE 296M, CEA-861-D
720p 59.94 x x x x x SMPTE 296M, CEA-861-D
720p 60 x x x x x SMPTE 296M, CEA-861-D
1080p 23.98 x x x x x SMPTE 274M, CEA-861-D
1080p 24 x x x x x SMPTE 274M, CEA-861-D
1080p 25 x x x x x SMPTE 274M, CEA-861-D
1080p 29.97 x x x x x SMPTE 274M, CEA-861-D
1080p 30 x x x x x SMPTE 274M, CEA-861-D
1080p 50 x x x x x SMPTE 274M, CEA-861-D
1080p 59.94 x x x x x SMPTE 274M, CEA-861-D
1080p 60 x x x x x SMPTE 274M, CEA-861-D
Page 86
Page 6.12 Rev D July 2014
6. Appendix Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Notes
Input connections
HDMI 1 & 2 inputs
19 way type A connector
1 TMDS Data 2+
2 TMDS Data 2 Shield
3 TMDS Data 2-
4 TMDS Data 1+
5 TMDS Data 1 Shield
6 TMDS Data 1-
7 TMDS Data 0+
8 TMDS Data 0 Shield
9 TMDS Data 0-
10 TMDS Clock+
11 TMDS Clock Shield
12 TMDS Clock-
13 CEC
14 not connected
15 SCL (DDC Clock)
16 SCA (DDC Data)
17 DDC/CEC Ground
18 +5 V Power
19 Hot Plug Detect
Composite video input
1 x RCA phono connector
PAL or NTSC video
S-Video input
4 pin mini-DIN
1 Y Ground
2 C Ground
3 Luminance (Y)
4 Chrominance (C)
pin view of panel connector
pin view of female connector
Page 87
Rev D July 2014 Page 6.13
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 6. Appendix
pin view of female connector
RGB input
15 way D-type connector
1 R
2 G
3 B
4 unused
5 Digital Ground (H Sync)
6 R Ground
7 B Ground
8 G Ground
9 +5v
10 Digital Ground (V Sync/DDC)
11 unused
12 SDA
13 H Sync
14 V Sync
15 SCL
Component 1 input
3 x RCA phono connectors
RGsB YPbPr YCbCr
Green + Sync Y Y
Blue Pb Cb
Red Pr Cr
RGBS
connect Sync to Video input
Component 2 input
5 x 75 ohm BNC
RGBHV RGsB YPbPr YCbCr
Green Green + Sync Y Y
Blue Blue Pb Cb
Red Red Pr Cr
Hsync
Vsync
Notes
In most cases, the Auto setting
will determine the correct color
space to use. If it does not,
you can select the appropriate
setting manually.
To select between RGB and
YPrPb signals, see Advanced
Menu, in 4.Controlling the
Projector.
Page 88
Page 6.14 Rev D July 2014
6. Appendix Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Control connections
Wired Remote control connection
3.5mm mini jack
Tip Power
Ring Signal
Sleeve Ground
Trigger 1 & 2 output
3.5mm mini jack
Tip Signal
Sleeve Ground
Serial control input
1 unused
2 Received Data (RX)
3 Transmitted Data (TX)
4 unused
5 Signal Ground
6 unused
7 unused
8 unused
9 unused
Null-modem cable
(used to connect the projector to a modem)
RX 2 --- 3 TX
TX 3 --- 2 RX
GND 5 --- 5 GND
Serial port settings
• Baud rate 38400 bps
• Data length 8 bits
• Stop bits one
• Parity none
• Flow control none
Notes
Trigger outputs are normally
at 0V, and rise to +12V when
triggered.
All of the projector’s features
can be controlled using an
external control system,
or a PC using a terminalemulation program such as
HyperTerminal, via a serial
or LAN connection. This
is done by using the text
strings described in Remote
communications protocol,
later in this section.
Only one remote connection
(RS232 or LAN) can be used at
any one time.
The projector is a DCE, so use:
• a straight cable to connect to a
computer, or
• a null-modem cable as shown
here to connect to another DCE
such as a modem.
Sleeve
Ring
Tip
Sleeve
Tip
pin view of female connector
Page 89
Rev D July 2014 Page 6.15
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 6. Appendix
Notes
All of the projector’s features
can be controlled using an
external control system,
or a PC using a terminalemulation program such as
HyperTerminal, via a serial
or LAN connection. This
is done by using the text
strings described in Remote
communications protocol,
later in this section.
More detailed LAN IP
conguration can be carried
out using a web browser.
For more information about
this, see Setting the LAN IP
conguration later in this
section.
Only one remote connection
(RS232 or LAN) can be used at
any one time.
Use:
• a straight cable to connect to a
hub or network, or
• a crossed cable as shown here
to connect ONLY to a computer
directly.
LAN connection
TCP Port number
7000
Default IP address
192.168.0.100
10BaseT Unshielded Twisted Pair cable
The standard wire colours as as follows:
1 White / Orange stripe
2 Orange
3 White / Green stripe
4 Blue
5 White / Blue stripe
6 Green
7 White / Brown stripe
8 Brown
Crossed cable
(used to connect directly to a computer with no hub or network.)
(Note that only the green and orange pairs are crossed)
1 White / Orange stripe White / Green stripe 1
2 Orange Green 2
3 White / Green stripe White / Orange stripe 3
4 Blue Blue 4
5 White / Blue stripe White / Blue stripe 5
6 Green Orange 6
7 White / Brown stripe White / Brown stripe 7
8 Brown Brown 8
top view of cable connector
(clip is underneath)
Page 90
Page 6.16 Rev D July 2014
6. Appendix Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Remote communications protocol
Introduction
All of the projector’s features can be controlled using an external control system,
or a PC using a terminal-emulation program such as HyperTerminal, via a serial
or LAN connection. This is done by using the text strings described in Remote
communications protocol, in section 6. Appendix.
There are 2 types of commands:
• Key commands
• Operation commands
All commands consist of ascii text strings starting with 2 letters:
• ky for key commands.
• op for operations commands.
All commands end with an ascii Carriage Return character.
Key Commands
Key commands are used to simulate remote control key presses, and use the
following format:
ky <keyname> [CR]
Example
ky pow.on [CR] simulates the POWER ON key being pressed.
The commands
Code transmitted <keyname> Description
0x01 pow.on Turn power on.
0x09 pow.off Turn power off.
0x15 menu Bring up or cancel menu display.
0x17 enter Keypad enter.
0x18 cur.down Keypad down arrow.
0x1A cur.up Keypad up arrow.
0x1D cur.left Keypad left arrow.
0x1F cur.righ Keypad right arrow.
0x80 bright Bring up or cancel brightness slide bar.
Notes
Details of how to connect to
the projector, using the serial
control input, can be found
earlier in this section.
Note: spaces in the commands
are necessary.
eg ky pow.on
NOT kypow.on
Page 91
Rev D July 2014 Page 6.17
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 6. Appendix
Code transmitted <keyname> Description
0x81 contrast Bring up or cancel contrast slide bar.
0x82 sharp Bring up or cancel sharpness slide bar.
0x83 nr Bring up or cancel noise reduction slide bar.
0x85 gam.sw Switch to the next gamma value.
0x8B src.1 Switch the active source to source 1.
0x8C src.2 Switch the active source to source 2.
0x8D src.3 Switch the active source to source 3.
0x8E src.4 Switch the active source to source 4.
0x8F src.5 Switch the active source to source 5.
0x93 osc.sw Switch to the next Overscan mode.
0x98 mem.1 Recall user memory associated with the User Memory A key.
0x99 mem.2 Recall user memory associated with the User Memory B key.
0x9A mem.3 Recall user memory associated with the User Memory C key.
0x9D asp.sw Switch to the next aspect ratio setting.
0xA3 lens.sw Bring up or cancel the lens control menu.
0xAA ctemp.sw Switch to the next colour temperature value.
0xAD pattern.sw Switch to the next test pattern.
Page 92
Page 6.18 Rev D July 2014
6. Appendix Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Operation Commands
Operation commands are used to simulate menu operations and determine the
settings of the projector, and use the following format:
op <operation> <command> [CR]
The <command> string can take one of the following formats:
<command> Description
Set = <value> Makes the setting take that value.
Get ? Asks what the current value is.
The value is returned as an ascii text string.
Increment + Adds 1 to the current value.
Decrement - Subtracts 1 from the current value.
Execute (none) Performs an action.
Example
op aspect = 1 [CR] sets the aspect ratio to Theaterscope.
op aspect ? [CR] asks what is the current aspect ratio.
op bright + [CR] increments the brightness setting.
op resync [CR] commands the projector to attempt to re-synchronise to the
current input source.
The commands
Operation <command> Values Notes
aspect = ? 0 = 16:9
1 = Theaterscope
2 = 4:3
3 = 4:3 Narrow
4 = Native
memory = ? 0 = Preset A
1 = Preset B
2 = Preset C
3 = Preset D
4 = Default
save.mem = 0 = Preset A
1 = Preset B
2 = Preset C
3 = Preset D
bright = ? + - 0 - 200
contrast = ? + - 0 - 200
saturat = ? + - 0 - 200
tint = ? + - 0 - 200
sharp = ? + - 0 - 200
nr = ? + - 0 - 200
overscan = ? 0 = Off
1 = Crop
2 = Zoom
Notes
Note: spaces in the commands
are necessary.
eg op aspect = 1
NOT opaspect=1
Page 93
Rev D July 2014 Page 6.19
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 6. Appendix
Operation <command> Values Notes
source.sel = ? 0 = HDMI 1
1 = HDMI 2
2 = RGB
3 = YPrPb 1
4 = YPrPb 2
5 = S-Video
6 = Video
resync (execute)
color.space = ? 0 = Auto
1 = YPbPr ( = REC709)
2 = YCbCr ( = REC601)
3 = RGB-PC
4 = RGB-Video
video.stand = ? 0 = Auto
1 = NTSC
2 = PAL
3 = SECAM
gamma = ? 0 = CRT
1 = Film
2 = Video
3 = Punch
4 = Graphics
color.temp = ? 0 = 5500K
1 = 6500K
2 = 7500K
3 = 9300K
dlp.frame = ? 0 = Auto
2 = 48 Hz
3 = 50 Hz
4 = 60 Hz
color.gamut = ? 0 = Auto
1 = REC709
2 = SMPTE C
3 = EBU
4 = Native
red.off = ? + - 0-200
green.off = ? + - 0-200
blue.off = ? + - 0-200
red.gain = ? + - 0-200
green.gain = ? + - 0-200
blue.gain = ? + - 0-200
vert.pos = ? + - 0-200
horiz.pos = ? + - 0-200
phase = ? + - 0-200
tracking = ? + - 0-200
sync.level = ? + - 0-200
menu.pos = ? 0 = Top left
1 = Top right
2 = Bottom left
3 = Bottom right
4 = Centre
Page 94
Page 6.20 Rev D July 2014
6. Appendix Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Operation <command> Values Notes
blank.screen = ? 0 = Logo
1 = Black
2 = Blue
3 = White
auto.pow.off = ? 0 = Off
1 = On
auto.pow.on = ? 0 = Off
1 = On
rear.proj = ? 0 = Off
1 = On
ceil.mode = ? 0 = Off
1 = On
logo.disp = ? 0 = Off
1 = On
1.key = ? 0 = HDMI 1
1 = HDMI 2
2 = RGB
3 = YPrPb 1
4 = YPrPb 2
5 = S-video
6 = Video
2.key = ? 0 = HDMI 1
1 = HDMI 2
2 = RGB
3 = YPrPb 1
4 = YPrPb 2
5 = S-video
6 = Video
3.key = ? 0 = HDMI 1
1 = HDMI 2
2 = RGB
3 = YPrPb 1
4 = YPrPb 2
5 = S-video
6 = Video
4.key = ? 0 = HDMI 1
1 = HDMI 2
2 = RGB
3 = YPrPb 1
4 = YPrPb 2
5 = S-video
6 = Video
trig.1 = ? 0 = Screen
1 = 16:9
2 = Theaterscope
3 = 4:3
4 = 4:3 Narrow
5 = RS232
6 = On
7 = Off
0: Trigger occurs when the projector is in
RUNNING mode
Page 95
Rev D July 2014 Page 6.21
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 6. Appendix
Operation <command> Values Notes
trig.2 = ? 0 = Screen
1 = 16:9
2 = Theaterscope
3 = 4:3
4 = 4:3 Narrow
5 = RS232
6 = On
7 = Off
0: Trigger occurs when the projector is in
RUNNING mode
auto.source = ? 0 = Off
1 = On
model.name ? <string>
ser.number ? <string>
soft.version ? <string>
act.source ? 0 = HDMI 1
1 = HDMI 2
2 = RGB
3 = YPrPb 1
4 = YPrPb 2
5 = S-video
6 = Video
Source Enable
h.refresh ? <number> KHz
v.refresh ? <number> Hz
pixel.clock ? <number> MHz
signal ? <string>
lamp.hours ? <number>
total.hours ? <number>
environment ? <string> Temperatures
fact.reset (execute)
blue.only = 0 = Off
1 = On
pattern = 0 = White
1 = Black
2 = Red
3 = Green
4 = Blue
5 = Cyan
6 = Magenta
7 = Yellow
8 = Chequerboard
9 = Greyscale
10 = Alignment Grid
11 = Off
altitude = ? 0 = Low
1 = High
status.check ? 0 = standby mode
1 = warm up mode
2 = running mode
3 = cooling mode
4 = error
focus + - + Focus Near
- Focus Far
Page 96
Page 6.22 Rev D July 2014
6. Appendix Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Operation <command> Values Notes
zoom + - + Zoom Out
- Zoom In
vert.offset + - + Shift Up
- Shift Down
horiz.offset + - + Shift Right
- Shift Left
ir.sw = ? 0 = Off
1 = On
IR Remote Control enable
eco.net.pow = ? 0 = RS232
1 = LAN
Serial/LAN switch
op net.ipaddr ? LAN IP address Default address is 192.168.0.100
To nd out how to change this, see Setting the
LANIPconguration, later in this section.
lamp.mode = ? 0 = economy mode
1 = standard mode
Page 97
Rev D July 2014 Page 6.23
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual 6. Appendix
SettingtheLANIPconguration
More detailed LAN IP conguration can be carried out using a web browser.
• Point your browser at the projector by typing the LAN IP Address into the
address bar, then press the Enter key.
• The embedded IP Conguration webpage should appear.
• Set the addresses as required, then click on Save.
Notes
The default LAN IP address is
192.168.0.100
If you suspect this has been
changed, then you can nd out
what it has been set to using
the remote communications
protocol Operation Command
op net.ipaddr?
Page 98
Digital Projection HIGHlite Cine 260, 1080p 330 User Manual
Loading...