Digital Projection E-Vision Series, 4500 WUXGA User Manual

Copyright

This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author.

Disclaimer

The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.

Trademark Recognition

Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations and pending applications in other countries throughout the world.

HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

All other pro

duct names used in this manual are the properties of their respective owners and are

acknowledged.

— i —

DLP Projector—User’s Manual

— ii —

Important Safety Information

Important:

It is strongly recommended that you read this section carefully before using the projector. These safety and usage instructions will ensure that you enjoy many years of safe use of the projector. Keep this manual for future reference.

Symbols Used

Warning symbols are used on the unit and in this manual to alert you of hazardous situations.

The following styles are used in this manual to alert you to important information.

Note:

Provides additional information on the topic at hand.

Important:

Provides additional information that should not be overlooked.

Caution:

Alerts you to situations that may damage the unit.

Warning:

Alerts you to situations that may damage the unit, create a hazardous environment, or cause personal injury.

Throughout this manual, component parts and items in the OSD menus are denoted in bold font as in this example: “Push the Menu button on the remote control to open the Main menu.”

General Safety Information

 Do not open the unit case. Aside from the projection lamp, there are no user-serviceable parts in

the unit. For servicing, contact qualified service personnel.

 Follow all warnings and cautions in this manual and on the unit case.

 The projection lamp is extremely bright by design. To avoid damage to eyes, do not look into the

lens when the lamp is on.

 Do not place the unit on an unstable surface, cart, or stand.

 Avoid using the system near water, in direct sunlight, or near a heating device.

 Do not place heavy objects such as books or bags on the unit.

P

r

e

f

a

c

e

Projector Installation Notice

 Place the projector in a horizontal position

The tilt angle of the projector please see Tilt Up/Down caution on page 50.

 Allow at least 50 cm clearance around the exhaust vent.

 Ensure that the intake vents do not recycle hot air from the exhaust vent.

 When operating the projector in an enclosed space, ensure that the surrounding air temperature

within the enclosure does not exceed operation temperature while the projector is running, and the air intake and exhaust vents are unobstructed.

 All enclosures should pass a certified thermal evaluation to ensure that the projector does not

recycle exhaust air, as this may cause the device to shutdown even if the enclosure temperature is with the acceptable operation temperature range.

– iii –

DLP Projector—User’s Manual

— iv —

Verify Installation Location

 To supply power, the 3-blade (with earthing lead) socket should be used to ensure proper

grounding and equalized ground potential for all of the equipment in the Projector System.

 The power code provided with the Projector should be used. In case of any missing item, other

qualified 3-blade (with earthing lead) power cord can be used as substitution; however, do not use 2-blade power cord.

 Verify if the voltage is stable, grounded properly and there is no electricity leakage.

 Measure total power consumption which should not higher the safety capacity and avoid safety

issue and short circuit.

 Turn on Altitude Mode when located in high altitude areas

 When installation the bracket, make sure the weight limit is not exceed and firmly secured.

 Avoid installing near air conditioner duct or subwoofer.

 Avoid installing at high temperature, insufficient cooling and heavy dust locations.

 Keep your product away from fluorescent lamps to avoid malfunction

caused by IR interference

 The VGA IN connector should be connected to the VGA IN port. Note that it should be inserted

tightly, with the screws on both sides securely fastened to ensure proper connection of the signal wire for achieving optimal display effect.

 The AUDIO IN connector should be connected to the AUDIO IN port and CANNOT be connected

to AUDIO OUT or other ports like BNC, RCA; otherwise, it will lead to mute output and even DAMAGE the port.

 Install the projector above 200cm to avoid damage.

 The power cord and signal cable should be connected before power on the projector. During the

projector starting and operating process, DO NOT insert or remove the signal cable or the power cord to avoid damaging the projector.

Cooling notes

Air outlet

 Make sure the air outlet is 50cm clear of any obstruction to ensure proper cooling.

 Air outlet location should not be in front of the lens of other projector to avoid causing illusions.

 Keep the outlet at least 100cm away from the inlets of other projectors

 The projector generates a massive amount of heat during use. The internal fan dissipates the heat

of the projector when shutting down, and such process may continue for a certain period. After the project enters STANDBY MODE status, press the AC power button to turn off the projector and remove the power cord. DO NOT remove the power cord during the shutdown process, as it may cause damage to the projector. In the meantime, the delayed heat radiating will also affect the service life of the projector. The shutdown process may vary depending on the model used. Whatever the case may be, be sure to disconnect the power cord till after the projector enters the STANDBY status.

Air inlet

 Make sure there is no object blocking air input within 30 cm.

 Keep the inlet away from other heat sources

 Avoided heavy dust area

P

r

e

f

a

c

e

Power Safety

 Only use the supplied power cord.

 Do not place anything on the power cord. Place the power cord where it will not be in the way of

foot traffic.

 Remove the batteries from the remote control when storing or not in use for a prolonged period.

Replacing the Lamp

Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 52 for clear and safe instructions for this procedure. Before replacing the lamp:

 Unplug the power cord.

 Allow the lamp to cool for about one hour.

Caution:

In rare cases the lamp bulb may burn out during normal operation and cause glass dust or shards to be discharged outward from the rear exhaust vent.

Do not inhale or do not touch glass dust or shards. Doing so could result in injury.

Always keep your face away from the exhaust vent so that you do not suffer from the gas and broken shards of the lamp.

Cleaning the Projector

 Unplug the power cord before cleaning. See Cleaning the Projector on page 58.

 Allow the lamp to cool for about one hour.

Regulatory Warnings

Before installing and using the projector, read the regulatory notices in the Regulatory Compliance on page 71.

Important Recycle Instructions:

Lamp(s) inside this product contain mercury. This product may contain other electronic waste that can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG

. For lamp

specific disposal information check WWW.LAMPRECYCLE.ORG.

Symbol Explanations

DISPOSAL: Do not use household or municipal waste collection services for disposal of electrical and electronic equipment. EU countries require the use of separate recycling collection services.

– v –

DLP Projector—User’s Manual

— vi —

Main Features

 Lightweight unit, easy to pack away and transport.

 Compatible with all major video standards including NTSC, PAL, and SECAM.

 A high brightness rating allows for presentations in daylight or in lit rooms.

 Supports resolutions up to WUXGA at 16.7 million colors to deliver crisp, clear images.

 Flexible setup allows for front, rear projections.

 Line-of-vision projections remain square, with advanced keystone correction for angled

projections.

 Input source automatically detected.

About this Manual

This manual is intended for end users and describes how to install and operate the DLP projector. Wherever possible, relevant information—such as an illustration and its description—has been kept on one page. This printer-friendly format is both for your convenience and to help save paper, thereby protecting the environment. It is suggested that you only print sections that are relevant to your needs.

P

r

e

f

a

c

e

– vii –

Table of Contents

GETTING STARTED........................................................................................................................................................... 1

PACKING CHECKLIST ........................................................................................................................................................... 1

VIEWS OF PROJECTOR PARTS............................................................................................................................................... 2

Front-right View ............................................................................................................................................................ 2

Top view—On-screen Display (OSD) buttons and LEDs....................................................................................... 3

Rear view....................................................................................................................................................................... 4

Bottom view................................................................................................................................................................... 6

REMOTE CONTROL PARTS ................................................................................................................................................... 7

REMOTE CONTROL OPERATING RANGE ............................................................................................................................... 9

PROJECTOR AND REMOTE CONTROL BUTTONS.................................................................................................................... 9

SETUP AND OPERATION............................................................................................................................................... 10

INSERTING THE REMOTE CONTROL BATTERIES ................................................................................................................. 10

INSTALLING OR REMOVING THE OPTIONAL LENS .............................................................................................................. 11

Removing the Existing Lens From the Projector ................................................................................................... 11

Installing the New Lens ............................................................................................................................................. 12

STARTING AND SHUTTING DOWN THE PROJECTOR............................................................................................................. 13

SETTING AN ACCESS PASSWORD (SECURITY LOCK) .......................................................................................................... 15

ADJUSTING THE PROJECTOR LEVEL ................................................................................................................................... 17

ADJUSTING PROJECTED IMAGE POSITION USING SHIFT ..................................................................................................... 18

Adjusting the vertical image position....................................................................................................................... 18

Adjusting the horizontal image position .................................................................................................................. 19

Shift Range Diagram ................................................................................................................................................. 19

ADJUSTING THE ZOOM, FOCUS AND KEYSTONE ................................................................................................................ 20

ADJUSTING THE VOLUME .................................................................................................................................................. 21

ON-SCREEN DISPLAY (OSD) MENU SETTINGS ...................................................................................................... 22

OSD MENU CONTROLS ..................................................................................................................................................... 22

Navigating the OSD ................................................................................................................................................... 22

SETTING THE OSD LANGUAGE .......................................................................................................................................... 23

OSD MENU OVERVIEW ..................................................................................................................................................... 24

IMAGE MENU..................................................................................................................................................................... 25

Computer Menu.......................................................................................................................................................... 26

Advanced Feature...................................................................................................................................................... 27

Color Manager ............................................................................................................................................................ 28

SETTINGS 1 MENU ............................................................................................................................................................. 29

Audio ............................................................................................................................................................................ 30

Advanced 1 Feature................................................................................................................................................... 31

Advanced 2 Feature................................................................................................................................................... 33

SETTINGS 2 MENU ............................................................................................................................................................. 34

Status ........................................................................................................................................................................... 35

Advanced 1 Feature................................................................................................................................................... 36

Advanced 2 Feature................................................................................................................................................... 48

MAINTENANCE AND SECURITY.................................................................................................................................. 50

TILT UP/DOWN CAUTION................................................................................................................................................... 50

The model with Standard lamp module .................................................................................................................. 50

The model with Tilt lamp module ............................................................................................................................. 50

REPLACING THE PROJECTION LAMP................................................................................................................................... 52

Resetting the Lamp.................................................................................................................................................... 55

CLEANING THE FILTER (FILTER: OPTIONAL PARTS) ............................................................................................................ 56

REPLACING THE FILTER ..................................................................................................................................................... 57

CLEANING THE PROJECTOR................................................................................................................................................ 58

Cleaning the Lens ...................................................................................................................................................... 58

Cleaning the Case...................................................................................................................................................... 58

USING THE PHYSICAL LOCK .............................................................................................................................................. 59

Using the Kensington® Lock ..................................................................................................................................... 59

Using the Security Chain Lock ................................................................................................................................. 59

DLP Projector—User’s Manual

— viii —

TROUBLESHOOTING...................................................................................................................................................... 60

COMMON PROBLEMS AND SOLUTIONS ............................................................................................................................... 60

TIPS FOR TROUBLESHOOTING ............................................................................................................................................ 60

LED ERROR MESSAGES..................................................................................................................................................... 61

IMAGE PROBLEMS.............................................................................................................................................................. 61

LAMP PROBLEMS ............................................................................................................................................................... 62

REMOTE CONTROL PROBLEMS .......................................................................................................................................... 62

AUDIO PROBLEMS ............................................................................................................................................................. 63

HAVING THE PROJECTOR SERVICED .................................................................................................................................. 63

HDMI Q & A .................................................................................................................................................................... 64

SPECIFICATIONS............................................................................................................................................................. 65

SPECIFICATIONS................................................................................................................................................................. 65

PROJECTION DISTANCE VS. PROJECTION SIZE.................................................................................................................... 66

Projection Distance and Size Table......................................................................................................................... 66

TIMING MODE TABLE ........................................................................................................................................................ 68

PROJECTOR DIMENSIONS ................................................................................................................................................... 70

REGULATORY COMPLIANCE....................................................................................................................................... 71

FCC WARNING .................................................................................................................................................................. 71

CANADA ............................................................................................................................................................................ 71

SAFETY CERTIFICATIONS ................................................................................................................................................... 71

APPENDIX I........................................................................................................................................................................ 72

RS-232C PROTOCOL.......................................................................................................................................................... 72

DLP Projector – User’s Manual

— 1 —

GETTING STARTED

Packing Checklist

Carefully unpack the projector and check that the following items are included:

PROJECTOR WITH LENS CAP

R

EMOTE CONTROL

(W

ITH TWO AA BATTERIES)

P

OWER CORD VGA CABLE (1.8M)

T

ILT LAMP MODULE

(O

PTIONAL)

CD-ROM

(T

HIS USER’S MANUAL)

W

ARRANTY CARD QUICK START CARD DUST FILTER

(O

PTIONAL)

Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work. It is recommend that you keep the original packing material should you ever need to return the equipment for warranty service.

Caution:

Avoid using the projector in dusty environments.

DLP Projector—User’s Manual

Views of Projector Parts

Front-right View

2

3

4

5

67810

111

9

ITEM LABEL DESCRIPTION SEE PAGE:

1.

Screw For ensure the lens position

2.

Vertical lens shift Adjusts the image position vertically

18

3.

Lens release button

Press the release button before removing the lens

11

4.

Horizontal lens shift Adjusts the image position horizontally

19

5.

IR receiver Receives IR signal from remote control

7

6.

Lens Projection Lens

7.

Focus ring Focuses the projected image

8.

Zoom ring Enlarges the projected image

20

9.

Height adjuster Adjusts level of projector

17

10.

Function keys

See Top view—On-screen Display (OSD) buttons and LEDs.

3

11.

Lamp cover Removes cover to replace lamp module

50

Important:

Ventilation openings on the projector allow for good air circulation, which keeps the projector lamp cool. Do not obstruct any of the ventilation openings.

Note:

Suggest to loosen the screw before lens shift adjustment and tighten up after finished adjustment.

— 2 —

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

Top view—On-screen Display (OSD) buttons and LEDs

ITEM LABEL DESCRIPTION

SEE

PAGE:

1.

MENU Opens and exits OSD menus

2.

Navigates and changes settings in the OSD Quick Menu – For Keystone

3.

ENTER Enter or confirm highlighted OSD menu item

22

4.

BLANK Displays a blank screen and mutes audio

5.

Navigates and changes settings in the OSD Quick Menu – For Volume -

22

6.

AUTO Optimizes image size, position, and resolution

7.

Navigates and changes settings in the OSD Quick Menu – For Volume +

8.

Navigates and changes settings in the OSD Quick Menu – For Keystone

22

9.

SOURCE Enter the Source menu

– 3 –

DLP Projector—User’s Manual

Rear view

12

3

4

56789 101112131415

1617

18 19

20

21

22

2

3

24

2

5

262728293031

ITEM LABEL DESCRIPTION SEE PAGE:

1.

VGA1 Connect a RGB cable from a computer or a video enabled device.

2.

AUDIO IN 1 Connect the AUDIO cable from an input device.

3.

VGA2 Connect a RGB cable from a computer or a video enabled device.

4.

AUDIO IN 2

Connect the AUDIO cable from an input device.

Note: Share with DVI & BNC audio input.

5.

POWER

Turns the projector on or off (main power switch must be turned on first). Press to place the projector in standby mode.

13

Red Standby, Over Temperature

Blue Lamp Lit , System stable

6.

PWR LED

Flashing

Power on, Cooling, Error code (See as LED indicator table)

7.

TEMP LED Red Over temperature

Red Lamp Lit , System stable, Lamp Fail

8.

READY LED

Flashing Error code (See as LED indicator table)

61

9.

HDMI Connect the HDMI cable from a HDMI device.

10.

DVI-D Connect the DVI cable from a computer.

11.

3D SYNC OUT (5V)

Connect 3D IR glasses receiver unit.

12.

DISPLAYPORT Connect a DISPLAYPORT cable to a DISPLAYPORT source.

13.

USB CHARGE (1.5A)

For USB charge.

14.

RJ-45 Connect a LAN cable from Ethernet.

— 4 —

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

– 5 –

ITEM LABEL DESCRIPTION SEE PAGE:

15.

VGA OUT

Connect the RGB cable to a display. (Pass through by VGA1 only)

16.

AUDIO OUT Connect an AUDIO cable for audio loop through.

17.

BNC Connect a BNC cable from a computer.

18.

IR receiver Receive IR signal from remote control.

7

19.

SERVICE For service use.

20.

RS-232 Connects RS-232 serial port cable for remote control.

21.

12V

When connected to the screen through a commercially available cable, the screen deploys automatically on start up of the projector. The screen retracts when the projector is powered off (see notes below).

22.

WIRED REMOTE

Wire remote control connector (connect with wire remote connector of the Remote Control set).

23.

AUDIO IN 3 L/R RCA (YPbPr)

Connect the audio cables from a audio device.

24.

AUDIO IN 4 L/R RCA (Video/ SVideo)

Connect the audio cables from a audio device.

25.

VIDEO Connect the composite cable from a video device.

26.

S-VIDEO Connect the S-video cable from a video device.

27.

YPbPr Connect a component video enabled device.

28.

AC IN Connects the power cable.

29.

Power switch Turns on/off the projector.

13

30.

Security chain lock

Helps protect the projector from unauthorized use.

31.

Kensington Lock

Secures to permanent object with a Kensington® Lock system.

59

Note:



To use this feature, you must plug in the connector before turn on/off the projector.



Screen controllers are supplied and supported by screen manufacturers.



Do not use this jack for anything other than intended use.

Note:

If your video equipment has both S-VIDEO and RCA jacks (composite video) connect to the S-VIDEO connector. S-VIDEO provides a better quality signal.

Warning:

As a safety precaution, disconnect all power to the projector and connecting devices before making connections.

DLP Projector—User’s Manual

Bottom view

ITEM LABEL DESCRIPTION SEE PAGE:

1.

Tilt adjustor Rotate adjuster lever to adjust angle position.

17

2.

Ceiling support holes

Contact your dealer for information on mounting the projector on a ceiling

Note: When installing, ensure that you use only UL Listed ceiling mounts. For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw depth of 6 mm (0.23 inch). The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount load capacity must exceed the weight of the installed equipment, and as an additional precaution be capable of withstanding three times the weight of the equipment (not less than

5.15 kg) over a period of 60 seconds.

— 6 —

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

Remote Control Parts

Important:

1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency

fluorescent lights can disrupt remote control operation.

2. Be sure nothing obstructs the path between the remote control and the projector. If the path between the remote control and the projector is obstructed, you can bounce the signal off certain reflective surfaces such as projector screens.

3. The buttons and keys on the projector have the same functions as the corresponding buttons on the remote control. This user’s manual describes the functions based on the remote control.

– 7 –

DLP Projector—User’s Manual

— 8 —

ITEM LABEL DESCRIPTION SEE PAGE:

1.

Power OFF Turns the projector off

13

2.

DVI Displays the DVI source selection

3.

VGA Displays the VGA source selection

4.

DP Displays the DisplayPort source selection

5.

Up cursor / Keystone+

Navigates and changes settings in the OSD Quick Menu – For Keystone

6.

ENTER Enters and confirms settings in the OSD

7.

Right cursor Navigates and changes settings in the OSD

8.

Down cursor / Keystone-

Navigates and changes settings in the OSD Quick Menu – For Keystone

22

9.

3D Activate 3D video

10.

PICTURE MODE Changes the Display Mode setting

11.

SOURCE Alternate input source

22

12.

CONTRAST Displays the contrast settings bar

13.

BRIGHT Displays the brightness setting bar

14.

SHARP Displays the sharpness setting bar

15.

COLOR Displays the color setting bar

16.

FREEZE Freezes/unfreezes the on-screen picture

17.

VOL + Adjusts volume

18.

AUTO Auto adjustment for frequency, phase, and position

19.

VOL - Adjusts volume

22

20.

BLANK Makes the screen blank

21.

TINT Displays the tint setting bar

22.

MUTE Mutes the built-in speaker

23.

STATUS

Opens the OSD Status menu (the menu only opens when an input device is detected)

24.

ASPECT RATIO Displays the ASPECT RATIO selections

25.

MENU

Opens

or closed the OSD

22

26.

Left cursor Navigates and changes settings in the OSD

22

27.

COMP Displays the Component source selection

28.

VIDEO Displays the VIDEO source selection

29.

HDMI 1 Displays the HDMI 1 source selection

30.

Power ON Turns the projector on

13

31.

Status LED Lights when the remote control is used

32.

IR transmitter Transmits signals to projector

33.

Wired remote connector

Wired remote function

used

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

– 9 –

Remote Control Operating Range

The remote control uses infrared transmission to control the projector. It is not necessary to point the remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and 15 degrees above or below the projector level. If the projector does not respond to the remote control, move a little closer.

Projector and Remote Control Buttons

The projector can be operated using the remote control or the buttons on the top of the projector. All operations can be carried out with the remote control; however, the buttons on the projector are limited in use.

DLP Projector—User’s Manual

— 10 —

SETUP AND OPERATION

Inserting the Remote Control Batteries

1.

Remove the battery compartment cover by sliding the cover in the direction of the arrow.

2.

Insert the battery with the positive side facing up.

3.

Replace the cover.

Caution:

1. Only use AA batteries (Alkaline batteries are recommended).

2. Dispose of used batteries according to local ordinance regulations.

3. Remove the batteries when not using the projector for prolonged periods.

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

Installing or Removing the Optional Lens

Caution:



Do not shake or place excessive pressure on the projector or the lens components as the

projector and lens components contain precision parts.



Before removing or installing the lens, be sure to turn off the projector, wait until the cooling

fans stop, and turn off the main power switch.



Do not touch the lens surface when removing or installing the lens.



Keep fingerprints, dust or oil off the lens surface.



Do not scratch the lens surface.



Work on a level surface with a soft cloth under it to avoid scratching.



If you remove and store the lens, attach the lens cap to the projector to keep off dust and dirt.

Removing the Existing Lens From the Projector

1.

Pull and release the top cover to open as shown.

2.

Push the LENSE RELEASE button to the unlock position.

3.

Grasp the lens.

4.

Rotate the lens counterclockwise. The existing lens will be disengaged.

5.

Pull out the existing lens slowly.

– 11 –

DLP Projector—User’s Manual

Installing the New Lens

1.

Align the notches and correctly position the electrical contact pad as shown in the picture.

Note:

Pin of Electrical contact pins should be in the direction as shown in the picture.

2.

Rotate the lens clockwise until you feel it click into place.

El

ectrical contact pins

— 12 —

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

Starting and Shutting down the Projector

1.

Remove the lens cap.

2.

Securely connect the power cord and signal cable. When connected, the power led will turn red.

3.

Turn on the lamp by pressing

“

” button on the rear of the

projector or “

” on the remote control. The PWR LED will now flash red. The startup screen will display in approximately 30 seconds. The first time you use the projector, you can select your preferred language from quick menu after the startup screen display.

– 13 –

DLP Projector—User’s Manual

4.

If more than one input device is connected, press the SOURCE button and use ▲▼ to scroll among devices.

 DVI: Digital Visual Interface

 HDMI: High-Definition Multimedia Interface

compatible

 DisplayPort: Digital display interface

 VGA 1 / 2: Analog RGB 1 / 2

 BNC: Analog RGB (BNC connector)



Component Video: DVD input YCbCr / YPbPr , or

HDTV input YPbPr

 S-Video: Super video (Y/C separated)

 Composite Video: Traditional composite video

5.

When the “Power Off? /Press Power again” message appears, press the POWER button. The projector turns off.

Caution:

1. Be sure to remove the lens cap before starting projector.

2. Do not unplug the power cord until the READY LED stops flashing–indicating the projector

has cooled down.

— 14 —

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

Setting an Access Password (Security Lock)

You can use the four (arrow) buttons to set a password and prevent unauthorized use of the

projector. When enabled, the password must be entered after you power on the projector. (See

Navigating the OSD on page 22 and Setting the OSD Language on page 23 for help on using

OSD menus.)

Important:

Keep the password in a safe place. Without the password, you will not be able to use the projector. If you lose the password, contact your reseller for information on clearing the password.

1.

Press the MENU button to open the OSD menu.

2.

Press the cursor ◄► button to move to the Settings 1 menu, press the cursor

▲▼ button to select Advanced 1.

3.

Press (Enter) / ► to enter the Advanced 1 sub menu. Press the cursor ▲▼ button to select Security

Lock.

4.

Press the cursor ◄► button to enter and enable or disable security lock function.

A password dialog box automatically appears.

– 15 –

DLP Projector—User’s Manual

5.

You can use the cursor buttons ▲▼◄► either on keypad or IR remote control for password entry. You can use any combination including the same arrow five times, but not less than five.

Press the cursor buttons in any order to set the password. Push the MENU button to exit the dialog box.

6.

The password confirm menu appears when user presses the power-on key in case the Security Lock is enabled. Enter the password in the order you set it at step 5. In case you forget the password, please contact the service center. The service center will validate the owner and help reset the password.

— 16 —

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

Adjusting the Projector Level

Take note of the following when setting up the projector:

 The projector table or stand should be level and sturdy.

 Position the projector so that it is perpendicular to the screen.

 Remove the Back Foot Holder on the rear adjuster foot before adjusting the projection

angle.

 Ensure the cables are in a safe location. You could trip over them.

1.

To raise the level of the projector, twist the adjusters counter clockwise.

2.

To lower the level of the projector, lift the projector and twist the adjusters clockwise.

– 17 –

DLP Projector—User’s Manual

Adjusting Projected Image Position Using Shift

Note:

Suggest to loosen the screw before lens shift adjustment and tighten up after finished adjustment.

The Shift feature provides a lens shift function that can be used to adjust the position of the projected image either horizontally or vertically within the range detailed below.

Shift is a unique system that provides lens shift while maintaining a much higher ANSI contrast ratio than traditional lens shift systems.

Adjusting the vertical image position

The vertical image height can be adjusted between 110% and -30% of offset position. Note that the maximum vertical image height adjustment can be limited by the horizontal image position. For example it is not possible to achieve the maximum vertical image position height detailed above if the horizontal image position is at maximum. Please consult the Shift Range diagram below for further clarification.

Screen

Distance

(L)

(H/2) x 10%

100%

Screen Height

(H)

+110%

-30%

0%

30% x (H/2)

110% x (H/2

)

— 18

—

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

Adjusting the horizontal image position

With the lens in the center position the horizontal image position can be adjusted to the left or right by up to a maximum of 10% of the half image width. Note that the maximum horizontal image height adjustment can be limited by the vertical image position. For example it is not possible to achieve the maximum horizontal image position if the vertical image position is at maximum. Please consult the Shift Range diagram below for further clarification.

Shift Range Diagram

The max H up shift = H/2 x 110% The max H down shift = H/2 x 30% The max W shift = W/2 x 10% When max W shift is W/2 x 10%

max H shift = H/2 x 100%

When max H shift is H/2 x 110%

max W shift = H x 0%

– 19 –

DLP Projector—User’s Manual

Adjusting the Zoom, Focus and Keystone

1.

Use the Image-zoom control (on the projector only) to resize the projected image and screen size.

2.

Use the Image-focus control (on the projector only) to sharpen the projected image.

3.

Use the KEYSTONE buttons (on the projector or the remote control) to correct image-trapezoid (wider top or bottom) effect.

Remote control and OSD panel

4.

The keystone control appears on the display.

— 20 —

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

Adjusting the Volume

1.

Press the Volume +/- buttons on the remote control. The volume control appears on the display.

2.

Press the Left or Right Cursor buttons on the

keypad to adjust

Volume +/-.

3.

Press the MUTE button to turn off the volume (This feature is available only on the remote).

– 21 –

DLP Projector—User’s Manual

— 22 —

ON-SCREEN DISPLAY (OSD) MENU SETTINGS

OSD Menu Controls

The projector has an OSD that lets you make image adjustments and change various settings.

Navigating the OSD

You can use the remote control cursor buttons or the buttons on the top of the projector to navigate and make changes to the OSD. The following illustration shows the corresponding buttons on the projector.

13

1

6

5

2

7

2

4

1

1 3

4

5

6

7

1. To enter the OSD, press the MENU button.

2. There are three menus. Press the cursor ◄► button to move through the menus.

3. Press the cursor ▲▼ button to move up and don in a menu.

4. Press ◄► to change values for settings.

5. Press MENU to close the OSD or leave a submenu.

Note:

Depending on the video source, not all items in the OSD are available. For example, the Horizontal/Vertical Position items in the Computer menu can only be modified when connected to a PC. Items that are not available cannot be accessed and are grayed out.

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

Setting the OSD Language

Set the OSD language to your preference before continuing.

1. Press the MENU button. Press the cursor ◄► button to navigate to Settings 1. Press

the cursor ▲▼ button to move to the Advanced 1 menu.

2. Press (Enter) / ► to enter the Advanced 1 sub menu. Press the cursor ▲▼ button

until Language is highlighted.

3. Press the cursor button until the language you want is highlighted.

4. Press the MENU button four times to close the OSD.

– 23 –

DLP Projector—User’s Manual

OSD Menu Overview

Use the following illustration to quickly find a setting or determine the range for a setting.

Image

Settings 1

Off, On

Blank, Red, Green, Blue, White

Off, On

3D

3D Sync Invert

3D Format

Hue

Saturation

English, Français, Español, Deutsch, Português, 簡体中文, 繁體中文, Italiano, Svenska, Nederlands, Suomi, Ελληνικά, Norsk, Polski, Русский, 한국어, 日本語,

اﻟﻌﺮﺑﻴﺔ , Magyar, ไทย, Türkçe, Čeština, Việt, ﻓﺎرﺳﯽ , תירבע

Off, On

Gain

1.8, 2.0, 2.2, 2.4, B&W, Linear

Off, On

Hue

Saturation

Gain

Hue

Saturation

Gain

Hue

Saturation

Gain

Hue

Saturation

Gain

Hue

Saturation

Gain

Red

Green

Blue

Reference Input Source Select (IR/Keypad)

Off, On

None, Grid, White, Red, Green, Blue, Black

Settings 2

Center, Down, Up, Left, Right

0%, 25%, 50%, 75%, 100%

Off, Low Power, Power On b y LAN, VGA Out

00-98

Normal, High

Display Mode

Brightness

Auto Image

Computer

Contrast

Advanced

Color Manager

Source

Aspect Ratio

Projection

Audio

Digital Zoom

Keystone

Advanced 1

Advanced 2

Auto Source

Auto Power On

No Signal Power Off

Status

Reset All

Lamp Mode

Advanced 1

Advanced 2

Volume

Security Lock

Blank Screen

Splash Logo

Keypad Lock

3D Setting

Horizontal Position

Vertical Position

Frequency

Tracking

Red

Language

Closed Captioning

Green

Blue

Cyan

Magenta

Yellow

White

Source

Mute

Test Pattern

H Image Shift

V Image Shift

Off, On

Menu Position

Translucent Menu

Low Power Mode

Lamp Hour Reset

Projector ID

Fan Speed

Off, On

Sleep Timer

Source Filter

ECO , Normal

DVI

HDMI

DisplayPort

VGA1

VGA2

Normal, Rear, Ceiling, Rear+Ceiling

Fill, 4:3, 16:9, Letter Box, Native, 2.35:1

Presentation, Bright, Game, Movie, TV, sRGB, BlackBoard, User1, User2

Off, On

Frame Sequential, Top/Bottom, Side-By-Side, Frame Packing (3D FramePacking HDMI source only)

Off, DLP-Link, IR

Disable, Enable

Auto Sync Off, On

BNC

Component Video

S-Video

Composite Video

Disable, Enable

Active Source

Video Information

Lamp Hours(ECO , Normal, Abnormal)

Serial Number

Software Version

Network State

Network

DHCP

IP Address

Subnet Mask

Gateway

DNS

Apply

Connect, Disconnect

Off, On

0~255, 0~255, 0~255, 0~255

OK / Cancel

Screen Capture

Projection Angle Caution

Off, On

— 24 —

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

Image Menu

Attention !

All of display mode parameters when changed will be saved to user mode.

Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Image Menu. Press the cursor ▲▼ button to move up and down in the Image menu. Press ◄►

to enter and change values for settings.

ITEM DESCRIPTION

Display Mode Press the cursor ◄► button to enter and set the Display Mode. Brightness Press the cursor ◄► button to enter and adjust the display brightness. Contrast Press the cursor ◄► button to enter and adjust the display contrast. Computer Press (Enter) / ► to enter the Computer menu. See Computer Menu on page 26.

Auto Image

Press

(Enter) / ► to automatically adjustment for phase, tracking, size and

position.

Advanced

Press

(Enter) / ► to enter the Advanced menu. See Advanced Feature on page

27.

Color Manager

Press

(Enter) / ► to enter the color manager menu. See page 28 for more

information on Color Manager.

– 25 –

DLP Projector—User’s Manual

Computer Menu

Press the MENU button to open the OSD menu. Press ◄► to move to the Image menu. Press ▲▼ to move to the Computer menu and then press Enter or ►. Press ▲▼ to move up and

down in the Computer menu.

ITEM DESCRIPTION

Horizontal Position Press the cursor ◄► button to enter and adjust the display position to left or right. Vertical Position Press the cursor ◄► button to enter and adjust the display position to up or down. Frequency Press the cursor ◄► button to enter and adjust the A/D sampling clock. Tracking Press the cursor ◄► button to enter and adjust the A/D sampling dot.

Auto Sync

Press the cursor ◄► button to enter and enable or disable the autolock control for RGB source.

— 26 —

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

Advanced Feature

Press the Menu button to open the OSD menu. Press ◄► to move to the Image menu. Press ▼▲ to move to the Advanced menu and then press Enter or ►. Press ▼▲ to move up and

down in the Advanced menu.

ITEM DESCRIPTION

Brilliant Color Press the cursor ◄► button to enter and adjust the Brilliant Color value. Sharpness Press the cursor ◄► button to enter and adjust the display sharpness. Gamma Press the cursor ◄► button to enter and adjust the gamma correction of the display. Color Temperature Press the cursor ◄► button to enter and adjust the color temperature.

Video AGC

Press the cursor ◄► button to enter and enable or disable the Automatic Gain Control for video source.

Video Saturation Press the cursor ◄► button to enter and adjust the video saturation. Video Tint Press the cursor ◄► button to enter and adjust the video tint/hue.

– 27 –

DLP Projector—User’s Manual

Color Manager

Press the Menu button to open the OSD menu. Press ◄► to move to the Image menu. Press ▼▲ to move to the Color Manager menu and then press Enter or ►. Press ▼▲ to move up and

down in the Color Manager menu.

ITEM DESCRIPTION

Red

Select to enter the Red Color Manager. Press the ◄► buttons to adjust the Hue, Saturation, and Gain.

Green

Select to enter the Green Color Manager. Press the ◄► buttons to adjust the Hue, Saturation, and Gain.

Blue

Select to enter the Blue Color Manager. Press the ◄► buttons to adjust the Hue, Saturation, and Gain.

Cyan

Select to enter the Cyan Color Manager. Press the ◄► buttons to adjust the Hue, Saturation, and Gain.

Magenta

Select to enter the Magenta Color Manager. Press the ◄► buttons to adjust the Hue, Saturation, and Gain.

Yellow

Select to enter the Yellow Color Manager. Press the◄► buttons to adjust the Hue, Saturation, and Gain.

White

Select to enter the White Color Manager. Press the ◄► buttons to adjust the Red, Green, and Blue.

— 28 —

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

Settings 1 Menu

Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Settings 1 menu. Press the cursor ▲▼ button to move up and down in the Settings 1 menu.

Press ◄► to

enter and change values for settings.

ITEM DESCRIPTION

Source

Press

(Enter) / ► to enter the Source menu. Reference input Source select

(IR / Keypad).

Projection Press the cursor ◄► button to enter and choose from four projection methods: Aspect Ratio Press the cursor ◄► button to enter and adjust the video aspect ratio. Keystone Press the cursor ◄► button to enter and adjust the display keystone. Digital Zoom Press the cursor ◄► button to enter and adjust the Digital Zoom menu. Audio Press (Enter) / ► to enter the Audio menu. See Audio on page 30.

Advanced 1

Press

(Enter) / ► to enter the Advanced 1 menu. See Advanced 1 Feature on

page 31.

Advanced 2

Press

(Enter) / ► to enter the Advanced 2 menu. See Advanced 2 Feature on

page 33.

– 29 –

DLP Projector—User’s Manual

Audio

Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 1 menu. Press ▼▲ to move to the Audio menu and then press Enter or ►. Press ▼▲ to move up and down in the Audio menu.

ITEM DESCRIPTION

Volume Press the cursor ◄► button to enter and adjust the audio volume. Mute Press the cursor ◄► button to enter and turn on or off the speaker.

— 30 —

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

Advanced 1 Feature

Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 1 menu. Press ▲▼ to move to the Advanced 1 menu and then press Enter or ►. Press ▲▼ to move up and down in the Advanced 1 menu. Press ◄► to enter and change values for setting.

ITEM DESCRIPTION

Language Press the cursor ◄► button to enter and select a different localization Menu.

Security Lock Press the cursor ◄► button to enter and enable or disable security lock function. Blank Screen Press the cursor ◄► button to enter and select different color to blank the screen. Splash Logo Press the cursor ◄► button to enter and select splash logo on or off. Closed Captioning Press the cursor ◄► button to enter and enable or disable Closed Captioning

Keypad Lock

Press the cursor ◄► button to enter and enable or disable keys can be work on keypad.

3D Setting

Press

(Enter) / ► to enter the 3D menu. See page 32 for more information on 3D

Setting.

Screen Capture

Press

(Enter) / ► to capture screen, and please wait saving picture.

Picture will auto showing after next power on.

Note:

To enjoy the 3D function, first enable the Play Movie in 3D setting found in your DVD device under

the 3D Disc Menu.

– 31 –

DLP Projector—User’s Manual

3D Setting

ITEM DESCRIPTION

3D Press the cursor ◄► button to enter and select different 3D mode. 3D Sync Invert Press the cursor ◄► button to enter and enable or disable 3D Sync Invert. 3D Format Press the cursor ◄► button to enter and enable or disable different 3D Format.

Note:

1. The 3D OSD menu item is gray if there is no appropriate 3D source. This is the default setting.

2. When the projector is connected to an appropriate 3D source, the 3D OSD menu item is enabled for selection.

3. Use 3D glasses to view a 3D image.

4. You need 3D content from a 3D DVD or 3D media file.

5. You need to enable the 3D source (some 3D DVD content may have a 3D on-off selection feature).

6. You need DLP link 3D or IR 3D shutter glasses. With IR 3D shutter glasses, you need to install a driver on your PC and connect a USB emitter.

7. The 3D mode of the OSD needs to match the type of glasses (DLP link or IR 3D).

8. Power on the glasses. Glasses normally have a power on -off switch. Each type of glasses has their own configuration instructions. Please follow the configuration instructions that come with your glasses to finish the setup process.

Note:

Since different types of glass (DLP link or IR shutter glass) have their own setting instructions,

Please follow the guide to finish the setup process.

— 32 —

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

Advanced 2 Feature

Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 1 menu. Press ▲▼ to move to the Advanced 2 menu and then press Enter or ►. Press ▲▼ to move up and down in the Advanced 2 menu. Press ◄► to enter and change values for setting.

ITEM DESCRIPTION

Test Pattern Press the cursor ◄► button to enter and select internal test pattern. H Image Shift Press the cursor ◄► button to enter and select H Image Shift.

V Image Shift Press the cursor ◄► button to enter and select V Image Shift.

– 33 –

DLP Projector—User’s Manual

Settings 2 Menu

Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Settings 2 menu. Press the cursor ▲▼ button to move up and down in the Settings 2 menu.

ITEM DESCRIPTION

Auto Source

Press the cursor ◄► button to enter and enable or disable automatic source detection.

No Singal Power Off (min.)

Press the cursor ◄► button to enter and enable or disable automatic shutdown of lamp when no signal.

Auto Power On

Press the cursor ◄► button to enter and enable or disable automatic power On when AC power is supplied.

Lamp Mode

Press the cursor ◄► button to enter and select the lamp mode for higher brightness or lower brightness to save lamp life.

Reset All Press (Enter) / ► to reset all settings to default values.

Status

Press

(Enter) / ► to enter the Status menu. See page 35 for more information on

Status.

Advanced 1

Press

(Enter) / ► to enter the Advanced 1 menu. See Advanced 1 Feature on

page 36.

Advanced 2

Press

(Enter) / ► to enter the Advanced 2 menu. See Advanced 2 Feature on

page 48.

— 34 —

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

Status

Press the cursor ▲▼ button to move up and down in the Settings 2 menu. Select the Status menu and press Enter or ► to enter.

ITEM DESCRIPTION

Active Source Display the activated source.

Video Information

Displays resolution/video information for RGB source and color standard for Video source.

Lamp Hours Lamp hour used information is displayed. (ECO, Normal, Abnormal )

Software Version Showing system software version.

Serial Number Showing serial number of this projector.

– 35 –

DLP Projector—User’s Manual

Advanced 1 Feature

Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 2 menu. Press ▲▼ to move to the Advanced 1 menu and then press Enter or ►. Press ▲▼ to move up and down in the Advanced 1 menu. Press ◄► to

enter and change values for setting.

ITEM DESCRIPTION

Menu Position Press the cursor ◄► button to enter and select different OSD location. Translucent Menu Press the cursor ◄► button to enter and select OSD background translucent level. Low Power Mode Press the cursor ◄► button to enter and turn Low Power Mode on or off.

Fan Speed

Press the cursor ◄► button to enter and toggle between Normal and High fan speeds. Note: We recommend selecting high speed in high temperatures, high humidity, or high altitude (higher than 1500m/4921ft) areas.

Lamp Hour Reset

After replacing the lamp, this item should be reset. See page 37 for more information on Lamp Hour Reset.

Projector ID

Press the cursor ◄► button to enter and adjust a two digit projector ID from 00 through 98.

Network

Press

(Enter) / ► to enter the Network menu. See page 37 for more information on

Network.

Projection Angle Caution

Press the cursor ◄► button to enter and turn Projection Angle Caution on or off.

— 36 —

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

Lamp Hour Reset

Please refer to Resetting the Lamp on page 55 to reset the lamp hour counter.

Network

ITEM DESCRIPTION

Network State Displays the network connection status.

DHCP

Press the cursor ◄► button to turn DHCP On or Off. Note: If you select DHCP Off, complete the IP Address, Subnet Mask, Gateway, and DNS fields.

IP Address Enter a valid IP address if DHCP is turned off.

Subnet Mask Enter a valid Subnet Mask if DHCP is turned off.

Gateway Enter a valid Gateway address if DHCP is turned off.

DNS Enter a valid DNS name if DHCP is turned off. Apply Press (Enter) / ► to confirm settings.

– 37

–

DLP Projector—User’s Manual

LAN_RJ45

Wired LAN Terminal functionalites

Remote control and monitoring of a projector from a PC (or Laptop) via wired LAN is also possible. Compatibility with Crestron / AMX (Device Discovery) / Extron control boxes enables not only collective projector management on a network but also management from a control panel on a PC (or Laptop) browser screen.

 Crestron is a registered trademark of Crestron Electronics, Inc. of the United States.

 Extron is a registered trademark of Extron Electronics, Inc. of the United States.

 AMX is a registered trademark of AMX LLC of the United States.

 PJLink applied for trademark and logo registration in Japan, the United States of America, and

other countries by JBMIA.

Supported External Devices

This projector is supported by the specified commands of the Crestron Electronics controller and related software (ex, RoomView ®).

http://www.crestron.com/

This projector is supported by AMX ( Device Discovery ).

http://www.amx.com/

This projector is compliant to support Extron device(s) for reference.

http://www.extron.com/

This projector supports all commands of PJLink Class1 (Version 1.00).

http://pjlink.jbmia.or.jp/english/

For more detail of information about the diverse types of external devices which can be connected to the LAN/RJ45 port and remote/control the projector, as well as the related control commands supporting for each external device, kindly please get contact with the Support-Service team directly.

— 38

—

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

LAN_RJ45

1. Connect an RJ45 cable to RJ45 ports on the projector and the PC (Laptop).

2. On the PC (Laptop), select Start → Control Panel → Network Connections.

– 39 –

DLP Projector—User’s Manual

3. Right-click on Local Area Connection, and select Properties.

4. In the Properties window, select the General tab, and select Internet Protocol (TCP/IP).

5. Click Properties.

6. Click Use the following IP address and fill in the IP address and Subnet mask, then click OK.

— 40 —

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

7. Press the Menu button on the projector.

8. Select Settings2→ Advanced1 → Network

9. After getting into Network, input the following:

 DHCP: Off

 IP Address: 10.10.10.10

 Subnet Mask: 255.255.255.0

 Gateway: 0.0.0.0

 DNS Server: 0.0.0.0

10. Press

(Enter) / ► to confirm settings.

Open a web browser (for example, Microsoft Internet Explorer with Adobe Flash Player 9.0 or higher).

11. In the Address bar, input the IP address: 10.10.10.10.

12. Press

(Enter) / ►.

The projector is setup for remote management. The LAN/RJ45 function displays as follows.

– 41

–

DLP Projector—User’s Manual

CATEGORY ITEM INPUT-LENGTH

IP Address 15

IP ID 3

Crestron Control

Port 5

Projector Name 10

Location 10

Projector

Assigned To 10

DHCP (Enabled) (N/A)

IP Address 15

Subnet Mask 15

Default Gateway 15

Network Configuration

DNS Server 15

Enabled (N/A)

New Password 10

User Password

Confirm 10

Enabled (N/A)

New Password 10

Admin Password

Confirm 10

For more information, please visit http://www.crestron.com.

— 42 —

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

Preparing Email Alerts

1. Make sure that user can access the homepage of LAN RJ45 function by web browser (for example, Microsoft Internet Explorer v6.01/v8.0).

2. From the Homepage of LAN/RJ45, click Alert Settings.

3. By default, these input boxes in Alert Settings are blank.

– 43 –

DLP Projector—User’s Manual

4. For Sending alert mail, input the following:

The 　 SMTP field is the mail server for sending out email (SMTP protocol). This is a required

field.

The 　 To field is the recipient’s email address (for example, the projector administrator). This is

a required field.

The 　 Cc field sends a carbon copy of the alert to the specified email address. This is an

optional field (for example, the projector administrator’s assistant).

The 　 From field is the sender’s email address (for example, the projector administrator). This is

a required field.

Select th　 e alert conditions by checking the desired boxes.

Note: Fill in all fields as specified. User can click Send Test Mail to test what setting is correct.

For successful sending an e-mail alert, you must select alert conditions and enter a correct e-mail address.

— 44 —

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

RS232 by Telnet Function

Besides projector connected to RS232 interface with “Hyper-Terminal” communication by dedicated RS232 command control, there is alternative RS232 command control way, so called “RS232 by TELNET” for LAN/RJ45 interface.

Quick Start-Guide for “RS232 by TELNET”

Check and get the IP-Address on OSD of the projector.

Make sure that laptop/PC can access the web-page of the projector.

Make sure that “Windows Firewall” setting to be disabled in case of “TELNET” function filtering out by laptop/PC.

Start => All Programs => Accessories => Command Prompt

– 45 –

DLP Projector—User’s Manual

Input the command format like the below:

telnet ttt.xxx.yyy.zzz 23 (“Enter” key pressed)

(ttt.xxx.yyy.zzz: IP-Address of the projector)

If Telnet-Connection ready, and user can have RS232 command input, then “Enter” key pressed, the RS232 command will be workable.

How to have TELNET enabled in Windows VISTA / 7

By default installation for Windows VISTA, “TELNET” function is not included. But end-user can have it by way of “Turn Windows features On or Off” to be enabled.

Open “Control Panel” in Windows VISTA

Open “Programs”

— 46 —

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

Select “Turn Windows features on or off” to open

Have “Telnet Client” option checked, then press “OK” button.

Specsheet for “RS232 by TELNET” :

1. Telnet: TCP

2. Telnet port: 23

(for more detail, kindly please get contact with the service agent or team)

3. Telnet utility: Windows “TELNET.exe” (console mode)

4. Disconnection for RS232-by-Telnet control normally: Close Windows Telnet utility directly after TELNET connection ready

5. Limitation 1 for Telnet-Control: there is less than 50 bytes for successive network payload for Telnet-Control application.

Limitation 2 for Telnet-Control: there is less than 26 bytes for one complete RS232 command for Telnet-Control.

Limitation 3 for Telnet-Control: Minimum delay for next RS232 command must be more than 200 (ms).

(*, In Windows XP built-in “TELNET.exe” utility, “Enter” key pressed will have “CarriageReturn” and “New-Line” code.)

– 47 –

DLP Projector—User’s Manual

Advanced 2 Feature

Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 2 menu. Press ▲▼ to move to the Advanced 2 menu and then press Enter or ►. Press ▲▼ to move up and down in the Advanced 2 menu. Press ◄► to

enter and change values for setting.

ITEM DESCRIPTION

Sleep Timer (min)

Press the cursor ◄► button to enter and set Sleep timer. The projector automatically turns off after the preset period of time.

Source Filter

Press

(Enter) / ► to enter the Source Filter menu. See page 49 for more

information on Source Filter.

— 48 —

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

Source Filter

Press the ENTER button to enter the Source Filter sub menu.

ITEM DESCRIPTION

DVI Press the ◄► buttons to enter and enable or disable the DVI source. HDMI Press the ◄► buttons to enter and enable or disable the HDMI source. DisplayPort Press the ◄► buttons to enter and enable or disable the DisplayPort source. VGA1 Press the ◄► buttons to enter and enable or disable the VGA1 source. VGA2 Press the ◄► buttons to enter and enable or disable the VGA2 source. BNC Press the ◄► buttons to enter and enable or disable the BNC source. Component Video Press the ◄► buttons to enter and enable or disable the Component Video source. S-Video Press the ◄► buttons to enter and enable or disable the S-Video source. Composite Video Press the ◄► buttons to enter and enable or disable the Composite Video source.

– 49 –

DLP Projector—User’s Manual

— 50 —

MAINTENANCE AND SECURITY

Tilt Up/Down caution

 When projector detect angle is over spec, popup caution message.

The model with Standard lamp module

The model with Standard lamp module can be used projection angle as shown below.

If Projector projection angle exceeds the drawing shown and don’t use tilt lamp module. Showing caution message for 5sec and then disappear, projector remain on. (every time when projector on

; This function

can be disable see

Advanced 1 Feature on page 36 )

15

Standard Lamp

The model with Tilt lamp module

The model with Tilt lamp module can be used projection angle as shown below.

If Projector projection angle exceeds the drawing shown and don’t use standard lamp module. Showing caution message for 5sec and then disappear, projector remain on. (every time when projector on

; This

function can be disable see

Advanced 1 Feature on page 36 )

Tilt Lamp

15

Warning:

Your operation might cause lamp defect and life decay. If used incorrect lamp module

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

Standard lamp module

Tilt lamp module

( Optional )

Note:

The standard lamp is to go with regular shipment for normal operation and the tilt lamp is an option lamp for abnormal operation

– 51 –

DLP Projector—User’s Manual

Replacing the Projection Lamp

The projection lamp should be replaced when it burns out. It should only be replaced with a certified replacement part, which you can order from your local dealer.

Important:

a. The projection lamp used in this product contains a small amount of mercury.

b. Do not dispose this product with general household waste.

c. Disposal of this product must be carried out in accordance with the regulations of your local

authority.

Warning:

Be sure to turn off and unplug the projector at least 30 minutes before replacing the lamp. Failure to do so could result in a severe burn.

Caution:

In rare cases the lamp bulb may burn out during normal operation and cause glass dust or shards to be discharged outward from the rear exhaust vent.

Do not inhale or do not touch glass dust or shards. Doing so could result in injury.

Always keep your face away from the exhaust vent so that you do not suffer from the gas and broken shards of the lamp.

When removing the lamp from a ceiling-mounted projector, make sure that no one is under the projector. Glass fragments could fall if the lamp has been burned out.

！

IF A LAMP EXPLODES

If a lamp explodes, the gas and broken shards may scatter inside the projector and they may come out of the exhaust vent. The gas contains toxic mercury.

Open windows and doors for ventilation.

If you inhale the gas or the shards of the broken lamp enter your eyes or mouth, consult the doctor immediately.

1.

Switch off the power to the projector by pressing the POWER button.

2.

Allow the projector to cool down at least 30 minutes.

3.

Disconnect the power cord.

— 52 —

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

4.

Unlock the lamp cover.

5.

Pull up and remove the cover.

6.

Use a screwdriver to remove the screws from the lamp module.

7.

Pull out the lamp module.

– 53

–

DLP Projector—User’s Manual

8.

Reverse steps 1 to 7 to install the new lamp module. While installing, align the lamp module with the connector and ensure it is level to avoid damage.

Note: The lamp module must sit securely in place and the lamp connector must be connected properly before tightening the screws.

— 54 —

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

Resetting the Lamp

After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following:

1.

Press the MENU button to open the OSD menu.

2.

Press the cursor ◄► button to move to the Settings 2 menu. Press the cursor button to move down to Advanced 1 and press enter.

3.

Press the cursor ▼▲ button to move down to Lamp Hour Reset.

4.

Press the cursor ► or Enter button.

A message screen appears.

5.

Press ▼▲◄► buttons to reset the lamp hour.

6.

Press the MENU button to get back to Settings 2.

– 55 –

DLP Projector—User’s Manual

Cleaning the filter (filter: optional parts)

The air filter prevents dust from accumulating on the surface of the optical elements inside the projector. If the filter is dirty or clogged, your projector may overheat or degrading the projected image quality.

1.

Turn off the projector, and unplug the AC power cord from the AC outlet.

2.

Cleaning the filter with a vacuum cleaner.

Caution:

Recommend avoiding dusty or smoky environments when you operate the projector, it may cause poor image quality.

If the filter is heavily clogged and unable to clean, replace a new filter.

Note:

Using a ladder is recommended to access the filter. Do not remove the projector from the wall mount.

— 56 —

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

Replacing the Filter

1.

Turn off the projector, and unplug the AC power cord from the AC outlet. Clean up the dust on the projector and around the air vents. Pull out the filter cover and remove from the projector

2.

Lift the filter from the filter cover.

3.

Replace a new filter module or replace filter into cover.

4.

Replace the filter cover back to the projector by pushing gently in the direction shown.

Warning:

Do not wash the filter with the water or other liquid matter

Important:

When the lamp is replaced, the filter should also be replaced, not cleaned.

– 57 –

DLP Projector—User’s Manual

— 58 —

Cleaning the Projector

Cleaning the projector to remove dust and grime will help ensure trouble-free operation.

Warning:

1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do

so could result in a severe burn.

2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings on the projector.

3. If a little water gets into the projector interior while cleaning, leave unplugged in a wellventilated room for several hours before using.

4. If a lot of water gets into the projector interior when cleaning, have the projector serviced.

Cleaning the Lens

You can purchase optic lens cleaner from most camera stores. Refer to the following to clean the projector lens.

1. Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly to the lens.)

2. Lightly wipe the lens in a circular motion.

Caution:

1. Do not use abrasive cleaners or solvents.

2. To prevent discoloration or fading, avoid getting cleaner on the projector case.

Cleaning the Case

Refer to the following to clean the projector case.

1. Wipe off dust with a clean dampened cloth.

2. Moisten the cloth with warm water and mild detergent (such as used to wash dishes), and then wipe the case.

3. Rinse all detergent from the cloth and wipe the projector again.

Caution:

To prevent discoloration or fading of the case, do not use abrasive alcohol-based cleaners.

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

Using the Physical Lock

Using the Kensington® Lock

If you are concerned about security, attach the projector to a permanent object with the Kensington slot and a security cable.

Note:

Contact your vendor for details on purchasing a suitable Kensington security cable.

The security lock corresponds to Kensington’s MicroSaver Security System. If you have any comment, contact: Kensington, 2853 Campus Drive, San Mateo, CA 94403, U.S.A. Tel: 800535-4242, http://www.Kensington.com.

Using the Security Chain Lock

In addition to the password protection function and the Kensington lock, the Security Chain Opening helps protect the PROJECTOR from unauthorized use.

See the following picture.

– 59

–

DLP Projector—User’s Manual

— 60 —

TROUBLESHOOTING

Common problems and solutions

These guidelines provide tips to deal with problems you may encounter while using the projector. If the problem remains unsolved, contact your dealer for assistance.

Often after time spent troubleshooting, the problem is traced to something as simple as a loose connection. Check the following before proceeding to the problem-specific solutions.

 Use some other electrical device to confirm that the electrical outlet is working.

 Ensure the projector is turned on.

 Ensure all connections are securely attached.

 Ensure the attached device is turned on.

 Ensure a connected PC is not in suspending mode.

 Ensure a connected notebook computer is configured for an external display.

(This is usually done by pressing an Fn-key combination on the notebook.)

Tips for Troubleshooting

In each problem-specific section, try the steps in the order suggested. This may help you to solve the problem more quickly.

Try to pin point the problem and thus avoid replacing non-defective parts. For example, if you replace batteries and the problem remains, put the original batteries back and go to the next step.

Keep a record of the steps you take when troubleshooting: The information may be useful when calling for technical support or for passing on to service personnel.

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

– 61 –

LED Error Messages

POWER LED TEMP LED READY LED

ERROR CODE MESSAGES

RED BLUE RED RED

System Initial Flash

－

OFF OFF

Ready to Power on (Standby) ON

－

OFF OFF

System Power on Flash

－

OFF OFF

Lamp Lit , System stable ON OFF ON

Cooling Flash

－

OFF OFF

Over Temperature ON

－

ON OFF

Thermal Break Sensor error 4 blinks

－

OFF OFF

Lamp Fail 5 blinks

－

OFF ON

Lamp Temperature shut down 5 blinks

－

OFF 1 blinks

Lamp Short circuit in output detected 5 blinks

－

OFF 2 blinks

Lamp End of lamp life detected 5 blinks

－

OFF 3 blinks

Lamp did not ignite 5 blinks

－

OFF 4 blinks

Lamp extinguished during normal operation 5 blinks

－

OFF 5 blinks

Lamp extinguished during run-up phase 5 blinks

－

OFF 6 blinks

Lamp voltage got error 5 blinks

－

OFF 7 blinks

Lamp ballast got error 5 blinks

－

OFF 8 blinks

Ballast watt value is out of range (Lamp Normal & Eco mode)

5 blinks

－

OFF 9 blinks

Lamp ballast Communication error 5 blinks

－

OFF 10 blinks

Lamp ballast power error 5 blinks

－

OFF 11 blinks

Fan-1 error 6 blinks

－

OFF 1 blinks

Fan-2 error 6 blinks

－

OFF 2 blinks

Fan-3 error 6 blinks

－

OFF 3 blinks

Fan-4 error 6 blinks

－

OFF 4 blinks

Fan-5 error 6 blinks

－

OFF 5 blinks

Case Open 7 blinks

－

OFF OFF

DAD1000 error 8 blinks

－

OFF OFF

Color wheel error 9 blinks

－

OFF OFF

In the event of an error, please disconnect the AC power cord and wait for one (1) minute before restarting the projector. If the Power or Ready LEDs are still blinking or any other situation that isn't listed in the chart above

, please contact your service center.

Image Problems

Problem: No image appears on the screen

1. Verify the settings on your notebook or desktop PC.

2. Turn off all equipment and power up again in the correct order.

Problem: The image is blurred

1. Adjust the Focus on the projector.

2. Press the Auto button on the remote control.

3. Ensure the projector-to-screen distance is within the specified range.

4. Check that the projector lens is clean.

DLP Projector—User’s Manual

— 62 —

Problem: The image is wider at the top or bottom (trapezoid effect)

1. Position the projector so it is as perpendicular to the screen as possible.

2. Use the Keystone button on the remote control to correct the problem.

Problem: The image is reversed

Check the Projection setting on the Settings 1 menu of the OSD.

Problem: The image is streaked

1. Set the Frequency and Tracking settings on the Image->Computer menu of the OSD to the default settings.

2. To ensure the problem is not caused by a connected PC’s video card, connect to another computer.

Problem: The image is flat with no contrast

Adjust the Contrast setting on the Image menu of the OSD.

Problem: The color of the projected image does not match the source image.

Adjust the Color Temperature and Gamma settings on the Image->Advanced menu of the OSD.

Lamp Problems

Problem: There is no light from the projector

1. Check that the power cable is securely connected.

2. Ensure the power source is good by testing with another electrical device.

3. Restart the projector in the correct order and check that the Power LED is on.

4. If you have replaced the lamp recently, try resetting the lamp connections.

5. Replace the lamp module.

6. Put the old lamp back in the projector and have the projector serviced.

Problem: The lamp goes off

1. Power surges can cause the lamp to turn off. Re-plug power cord. When the Power LED is on, press the power button.

2. Replace the lamp module.

3. Put the old lamp back in the projector and have the projector serviced.

Remote Control Problems

Problem: The projector does not respond to the remote control

1. Direct the remote control towards remote sensor on the projector.

2. Ensure the path between remote and sensor is not obstructed.

3. Turn off any fluorescent lights in the room.

4. Check the battery polarity.

5. Replace the battery.

6. Turn off other Infrared-enabled devices in the vicinity.

7. Have the remote control serviced.

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

– 63 –

Audio Problems

Problem: There is no sound

1. Adjust the volume on the remote control.

2. Adjust the volume of the audio source.

3. Check the audio cable connection.

4. Test the source audio output with other speakers.

5. Have the projector serviced.

Problem: The sound is distorted

1. Check the audio cable connection.

2. Test the source audio output with other speakers.

3. Have the projector serviced.

Having the Projector Serviced

If you are unable to solve the problem, you should have the projector serviced. Pack the projector in the original carton. Include a description of the problem and a checklist of the steps you took when trying to fix the problem: The information may be useful to service personnel. For servicing, return the projector to the place you purchased it.

DLP Projector—User’s Manual

— 64 —

HDMI Q & A

Q. What is the difference between a “Standard” HDMI cable and a “High-Speed”

HDMI cable?

Recently, HDMI Licensing, LLC announced that cables would be tested as Standard or HighSpeed cables.

˙Standard (or “category 1”) HDMI cables have been tested to perform at speeds of 75Mhz or up

to 2.25Gbps, which is the equivalent of a 720p/1080i signal.

˙High Speed (or “category 2”) HDMI cables have been tested to perform at speeds of 340Mhz or

up to 10.2Gbps, which is the highest bandwidth currently available over an HDMI cable and can successfully handle 1080p signals including those at increased color depths and/or increased refresh rates from the Source. High-Speed cables are also able to accommodate higher resolution displays, such as WQXGA cinema monitors (resolution of 2560 x 1600).

Q. How do I run HDMI cables longer than 10 meters?

There are many HDMI Adopters working on HDMI solutions that extend a cable’s effective distance from the typical 10 meter range to much longer lengths. These companies manufacture a variety of solutions that include active cables (active electronics built into cables that boost and extend the cable’s signal), repeaters, amplifiers as well as CAT5/6 and fiber solutions.

Q. How can I tell if a cable is an HDMI certified cable?

All HDMI products are required to be certified by the manufacturer as part of the HDMI Compliance Test Specification. However, there may be instances where cables bearing the HDMI logo are available but have not been properly tested. HDMI Licensing, LLC actively investigates these instances to ensure that the HDMI trademark is properly used in the market. We recommend that consumers buy their cables from a reputable source and a company that is trusted.

For more detail information check http://www.hdmi.org/learningcenter/faq.aspx#49

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

– 65 –

SPECIFICATIONS

Specifications

Model E-Vision 4500 WUXGA

Display type

0.67" WUXGA DC3 TypeA

Resolution

1920x1200

Projection distance

1.5 meters ~ 7 meters

Projection screen size

36” ~ 210”

Projection lens

Manual Focus/Manual Zoom

Throw ratio

1.54 ~ 1.93

Vertical keystone correction

±40°

Projection methods

Front, Rear, Desktop/Ceiling (Rear, Front)

Data compatibility

VGA, SVGA, XGA, SXGA, SXGA+, UXGA, WUXGA@60hz, Mac

SDTV/EDTV/ HDTV

480i, 576i, 480p, 576p, 720p, 1080i, 1080p

Video compatibility

NTSC (M, 3.58/4.43 MHz), PAL (B, D, G, H, I, M, N), SECAM (B, D, G, K, K1, L)

H-Sync

15, 31-91.4kHz

V-Sync

24~30Hz, 47 ~ 120Hz

Safety certification

FCC-B, cUL, UL, CE, C-tick, CCC, KC, CB, PCT

Operation temperature

5° ~ 35°C

Dimensions

431.11mm (W) x 344.16mm (D) x 180.57mm (H)

AC Input

AC Universal 100 – 240V

Power consumption

Typical 480W (boost) , <0.5watts(Stand By)/

Typical 365W(standard) , <0.5watts(Stand By)

Lamp

370W (Normal) / 280W (Eco)

Audio speaker

3W x 2

VGA x 2

DisplayPort x 1

DVI-D x 1

S-Video x 1

5 BNC (RGBHV) x 1

Component x 1

Composite video x 1

HDMI x 1

RCA stereo x 2

Input Terminals

Mini-jack stereo x 2

VGA x 1

Output Terminals

PC audio out x 1

RS-232C

RJ45

Screen trigger: DC Jack x 1 (DC12V 200mA output function)

wire remote

USB (type B) only for service/mouse control

USB (type A) only for power supply; WHDI

Control Terminals

3D sync

Security

Kensington lock

DLP Projector—User’s Manual

Projection Distance vs. Projection Size



V-Sync

Projection Distance

H

O

Image Height

A

Projection Distance and Size Table

Standard projection lens: TR: 1.54 ~ 1.93; offset=110%

TELE WIDE

Distance (m)

1.66 3.33 4.16 8.31 1.66 3.32 6.63 9.95

Diagonal (")

40 80 100 200 50 100 200 300

Image Width (mm)

862 1723 2154 4308 1077 2154 4308 6462

Image Height (mm)

538 1077 1346 2692 673 1346 2692 4039

H (mm)

269 538 673 1346 337 673 1346 2019

O (mm)

296 592 740 1481 370 740 1481 2221

A (mm)

27 54 67 135 34 67 135 202

Long throw projection lens: TR: 1.93 ~ 2.9; offset=110%

TELE WIDE

Distance (m)

2.5 6.25 12.49 18.74 2.08 6.24 12.47 18.71

Diagonal (")

40 100 200 300 50 150 300 450

Image Width (mm)

862 2154 4308 6462 1077 3231 6462 9693

Image Height (mm)

538 1346 2692 4039 673 2019 4039 6058

H (mm)

269 673 1346 2019 337 1010 2020 3029

O (mm)

296 740 1481 2221 370 1111 2222 3332

A (mm)

27 67 135 202 34 101 202 303

— 66 —

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

– 67 –

Short throw projection lesn: TR: 0.77; offset=110%

FIX

Distance (m)

0.66 1.33 1.66 2.49

Diagonal (")

40 80 100 150

Image Width (mm)

862 1723 2154 3231

Image Height (mm)

538 1077 1346 2019

H (mm)

269 538 673 1010

O (mm)

296 592 740 1111

A (mm)

27 54 67 101

offset % = O/H × 100% O=A+H H=(1/2) × (image height)

DLP Projector—User’s Manual

— 68 —

Timing Mode Table

Signal Resolution

H-Sync

(KHz)

V-Sync

(Hz)

Composite

S-Video

Component

RGB

(Analog)

DP/DVI

HDMI (Digital)

NTSC

－

15.7 60.0 ○

－－－

PAL/SECAM

－

15.6 50.0 ○

－－－

640 x 400 37.9 85.1

－－

○ ○

720 x 400 31.5 70.1

－－

○ ○

720 x 400 37.9 85.0

－－

○ ○

640 x 480 31.5 60.0

－－

○ ○

640 x 480 37.9 72.8

－－

○ ○

640 x 480 37.5 75.0

－－

○ ○

640 x 480 43.3 85.0

－－

○ ○

800 x 600 35.2 56.3

－－

○ ○

800 x 600 37.9 60.3

－－

○ ○

800 x 600 46.9 75.0

－－

○ ○

800 x 600 48.1 72.2

－－

○ ○

800 x 600 53.7 85.1

－－

○ ○

800 x 600 76.3 120.0

－－

○ ○

1024 x 576 35.8 60.0

－－

○ ○

1024 x 600 37.3 60.0

－－

○ ○

1024 x 600 41.5 65.0

－－

○ ○

1024 x 768 48.4 60.0

－－

○ ○

1024 x 768 56.5 70.1

－－

○ ○

1024 x 768 60.0 75.0

－－

○ ○

1024 x 768 68.7 85.0

－－

○ ○

1024 x 768 97.6 120.0

－－

○ ○

1024 x 768 99.0 120.0

－－

○ ○

1152 x 864 67.5 75.0

－－

○ ○

1280 x 720 45.0 60.0

－－

○ ○

1280 x 720 90.0 120.0

－－

○ ○

1280 x 768 47.4 60.0

－－

○ ○

1280 x 768 47.8 59.9

－－

○ ○

1280 x 800 49.7 59.8

－－

○ ○

1280 x 800 62.8 74.9

－－

○ ○

1280 x 800 71.6 84.9

－－

○ ○

1280 x 800 101.6 119.9

－－

○ ○

1280 x 1024 64.0 60.0

－－

○ ○

1280 x 1024 80.0 75.0

－－

○ ○

1280 x 1024 91.1 85.0

－－

○ ○

1280 x 960 60.0 60.0

－－

○ ○

1280 x 960 85.9 85.0

－－

○ ○

1360 x 768 47.7 60.0

－－

○ ○

1400 x 1050 65.3 60.0

－－

○ ○

1440 x 900 55.5 59.9

－－

○ ○

1440 x 900 55.9 59.9

－－

○ ○

1440 x 900 70.6 75.0

－－

○ ○

VESA

1600 x1200 75.0 60.0

－－

○ ○

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

– 69 –

Signal Resolution

H-Sync

(KHz)

V-Sync

(Hz)

Composite

S-Video

Component

RGB

(Analog)

DP/DVI

HDMI (Digital)

1680 x 1050 64.7 59.9

－－

○ ○

1680 x 1050 65.3 60.0

－－

○ ○

1920 x 1200 74.0 60.0

－－

○ ○

1920 x 1080 67.5 60.0

－－

○ ○

640 x 480 35.0 66.7

－－

○ ○

832 x 624 49.7 74.5

－－

○ ○

1024 x 768 60.2 74.9

－－

○ ○

Apple Macintosh

1152 x 870 68.7 75.1

－－

○ ○

480i 15.7 60.0

－

○

－

○

SDTV

576i 15.6 50.0

－

○

－

○

576p 31.3 50.0

－

○

－

○

EDTV

480p 31.5 60.0

－

○

－

○

720p 37.5 50.0

－

○

－

○

720p 45.0 60.0

－

○

－

○

1080i 33.8 60.0

－

○

－

○

1080i 28.1 50.0

－

○

－

○

1080p 27.0 24.0

－

○

－

○

1080p 28.0 25.0

－

○

－

○

1080p 33.7 30.0

－

○

－

○

1080p 56.3 50.0

－

○

－

○

HDTV

1080p 67.5 60.0

－

○

－

○

O: Frequency supported

—: Frequency not supported

Resolution others than native resolution may be display with uneven size of text or line.

★ The color of mean Displayable only. (4:3 only)

★ The color of mean may have a little noise is acceptable, Because video mode sync don’t

auto adjustment.

★ HDTV timing main check tool is DVD player, VG828 is secondary.

DLP Projector—User’s Manual

Projector Dimensions

— 70 —

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

– 71 –

REGULATORY COMPLIANCE

FCC Warning

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense.

Changes or modifications not expressly approved by the parties responsible for compliance could void the user’s authority to operate the equipment.

Canada

This class B digital apparatus complies with Canadian ICES-003.

Safety Certifications

FCC-B, cUL, UL, CE, C-tick, CCC, KC, CB, PCT

DLP Projector—User’s Manual

— 72 —

APPENDIX I

RS-232C Protocol

RS232 Setting

Baud rate:

9600

Parity check: None

Data bit: 8

Stop bit: 1

Flow Control None

Control Command Structure

Header code Command code Data code End code

HEX Command Data 0Dh

ASCII ‘V’ Command Data CR

Operation Command

Note:

XX=00-98, projector's ID, XX=99 is for all projectors

Return Result P=Pass / F=Fail

n: 0:Disable/1: Enable/Vaule(0~9999)

Command Group 00

ASCII HEX Function Description Return Result

VXXS0001 56h Xh Xh 53h 30h 30h 30h 31h 0Dh Power On P/F

VXXS0002 56h Xh Xh 53h 30h 30h 30h 32h 0Dh Power Off P/F

VXXS0003 56h Xh Xh 53h 30h 30h 30h 33h 0Dh Resync P/F

VXXG0004 56h Xh Xh 47h 30h 30h 30h 34h 0Dh Get Lamp Hours Pn/F

VXXS0006 56h Xh Xh 53h 30h 30h 30h 36h 0Dh System Reset P/F

VXXG0007 56h Xh Xh 47h 30h 30h 30h 37h 0Dh Get System Status

0:Reset 1:Standby 2:Operation 3:Cooling

Pn/F

VXXG0008 56h Xh Xh 47h 30h 30h 30h 38h 0Dh Get F/W Version Pn/F

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

– 73 –

Command Group 01

ASCII HEX Function Description Return Value

VXXG0101 56h Xh Xh 47h 30h 31h 30h 31h 0Dh Get Brightness n=0~100 Pn/F

VXXS0101n 56h Xh Xh 53h 30h 31h 30h 31h nh 0Dh Set Brightness n=0~100 P/F

VXXG0102 56h Xh Xh 47h 30h 31h 30h 32h 0Dh Get Contrast n=0~100 Pn/F

VXXS0102n 56h Xh Xh 53h 30h 31h 30h 32h nh 0Dh Set Contrast n=0~100 P/F

VXXG0103 56h Xh Xh 47h 30h 31h 30h 33h 0Dh Get Color n=0~100 Pn/F

VXXS0103n 56h Xh Xh 53h 30h 31h 30h 33h nh 0Dh Set Color n=0~100 P/F

VXXG0104 56h Xh Xh 47h 30h 31h 30h 34h 0Dh Get Tint n=0~100 Pn/F

VXXS0104n 56h Xh Xh 53h 30h 31h 30h 34h nh 0Dh Set Tint n=0~100 P/F

VXXG0105 56h Xh Xh 47h 30h 31h 30h 35h 0Dh Get Sharpness 0~31 Pn/F

VXXS0105n 56h Xh Xh 53h 30h 31h 30h 35h nh 0Dh Set Sharpness 0~31 P/F

VXXG0106 56h Xh Xh 47h 30h 31h 30h 36h 0Dh

Get Color Temperature

0:Warm 1:Normal 2:Cold

Pn/F

VXXS0106n 56h Xh Xh 53h 30h 31h 30h 36h nh 0Dh

Set Color Temperature

0:Warm 1:Normal 2:Cold

P/F

VXXG0107 56h Xh Xh 47h 30h 31h 30h 37h 0Dh Get Gamma

0:1.8 1:2.0 2:2.2 3:2.4 4:B&W 5:Linear

Pn/F

VXXS0107n 56h Xh Xh 53h 30h 31h 30h 37h nh 0Dh Set Gamma

0:1.8 1:2.0 2:2.2 3:2.4 4:B&W 5:Linear

P/F

Command Group 02

ASCII HEX Function Description Return Value

VXXS0201 56h Xh Xh 53h 30h 32h 30h 31h 0Dh Select RGB P/F

VXXS0202 56h Xh Xh 53h 30h 32h 30h 32h 0Dh Select RGB2 P/F

VXXS0203 56h Xh Xh 53h 30h 32h 30h 33h 0Dh Select DVI P/F

VXXS0204 56h Xh Xh 53h 30h 32h 30h 34h 0Dh Select Video P/F

VXXS0205 56h Xh Xh 53h 30h 32h 30h 35h 0Dh Select S-Video P/F

VXXS0206 56h Xh Xh 53h 30h 32h 30h 36h 0Dh Select HDMI P/F

VXXS0207 56h Xh Xh 53h 30h 32h 30h 37h 0Dh Select BNC P/F

VXXS0208 56h Xh Xh 53h 30h 32h 30h 38h 0Dh

Select Component

P/F

DLP Projector—User’s Manual

— 74 —

Command Group 02

ASCII HEX Function Description Return Value

VXXS0209 56h Xh Xh 53h 30h 32h 30h 39h 0Dh

Select HDMI 2 (MEDIA)

P/F

VXXS0210 56h Xh Xh 53h 30h 32h 31h 30h 0Dh

Select Display Port

P/F

VXXS0211 56h Xh Xh 53h 30h 32h 31h 31h 0Dh Select Multi Media P/F

VXXG0220 56h Xh Xh 47h 30h 32h 32h 30h 0Dh

Get Current Source

Return 1:RGB 2:RGB2 3:DVI 4:Video 5:S-Video 6:HDMI 1 7:BNC 8:Component 9:HDMI 2 10:Display Port 11:Multi Media.

Pn/F

Command Group 03

ASCII HEX Function Description Return Value

VXXG0301 56h Xh Xh 47h 30h 33h 30h 31h 0Dh Get Scaling

0:Fill 1:4:3 2:16:9 3:Letter Box 4:Native 5:2.35:1

Pn/F

VXXS0301n 56h Xh Xh 53h 30h 33h 30h 31h nh 0Dh Set Scaling

0:Fill 1:4:3 2:16:9 3:Letter Box 4:Native 5:2.35:1

P/F

VXXG0302 56h Xh Xh 47h 30h 33h 30h 32h 0Dh Blank Pn/F

VXXS0302n 56h Xh Xh 53h 30h 33h 30h 32h nh 0Dh Blank P/F

VXXG0303 56h Xh Xh 47h 30h 33h 30h 33h 0Dh Auto Keystone On Pn/F

VXXS0303n 56h Xh Xh 53h 30h 33h 30h 33h nh 0Dh Auto Keystone On P/F

VXXG0304 56h Xh Xh 47h 30h 33h 30h 34h 0Dh Freeze On Pn/F

VXXS0304n 56h Xh Xh 53h 30h 33h 30h 34h nh 0Dh Freeze On P/F

VXXG0305 56h Xh Xh 47h 30h 33h 30h 35h 0Dh Volume n=0~10 Pn/F

VXXS0305n 56h Xh Xh 53h 30h 33h 30h 35h nh 0Dh Volume n=0~10 P/F

VXXG0306 56h Xh Xh 47h 30h 33h 30h 36h 0Dh Treble n=0~16 Pn/F

VXXS0306n 56h Xh Xh 53h 30h 33h 30h 36h nh 0Dh Treble n=0~16 P/F

VXXG0307 56h Xh Xh 47h 30h 33h 30h 37h 0Dh Bass n=0~16 Pn/F

VXXS0307n 56h Xh Xh 53h 30h 33h 30h 37h nh 0Dh Bass n=0~16 P/F

VXXG0308 56h Xh Xh 47h 30h 33h 30h 38h 0Dh Projection Mode

0:Front 1:Rear 2:Ceiling 3:Rear+Ceiling

Pn/F

D

L

P

r

o

j

e

c

t

o

r

—

U

s

e

r

’

s

M

a

n

u

a

l

– 75 –

Command Group 03

ASCII HEX Function Description Return Value

VXXS0308n 56h Xh Xh 53h 30h 33h 30h 38h nh 0Dh Projection Mode

0:Front 1:Rear 2:Ceiling 3:Rear+Ceiling

P/F

VXXG0309 56h Xh Xh 47h 30h 33h 30h 39h 0Dh

Set vertical keystone value

n=-40~+40 Pn/F

VXXS0309n 56h Xh Xh 53h 30h 33h 30h 39h nh 0Dh

Set vertical keystone value

n=-40~+40 P/F

VXXG0310 56h Xh Xh 47h 30h 33h 31h 30h 0Dh

Set horizontal keystone value

n=-20~+20 Pn/F

VXXS0310n 56h Xh Xh 53h 30h 33h 31h 30h nh 0Dh

Set horizontal keystone value

n=-20~+20 P/F

VXXG0311 56h Xh Xh 47h 30h 33h 31h 31h 0Dh Adjust the zoom n=-10~+10 Pn/F

VXXS0311n 56h Xh Xh 53h 30h 33h 31h 31h nh 0Dh Adjust the zoom n=-10~+10 P/F

VXXG0312 56h Xh Xh 47h 30h 33h 31h 32h 0Dh Adjust the focus n=-20~+20 Pn/F

VXXS0312n 56h Xh Xh 53h 30h 33h 31h 32h nh 0Dh Adjust the focus n=-20~+20 P/F

VXXG0313 56h Xh Xh 47h 30h 33h 31h 33h 0Dh

Adjust the vertical lens shift

n=-20~+20 Pn/F

VXXS0313n 56h Xh Xh 53h 30h 33h 31h 33h nh 0Dh

Adjust the vertical lens shift

n=-20~+20 P/F

VXXG0314 56h Xh Xh 47h 30h 33h 31h 34h 0Dh

Adjust the horizontal lens shift

n=-20~+20 Pn/F

VXXS0314n 56h Xh Xh 53h 30h 33h 31h 34h nh 0Dh

Adjust the horizontal lens shift

n=-20~+20 P/F

VXXG0315 56h Xh Xh 47h 30h 33h 31h 35h 0Dh 3D

0:Off 1:DLP-Link 2:IR

Pn/F

VXXS0315n 56h Xh Xh 53h 30h 33h 31h 35h nh 0Dh 3D

0:Off 1:DLP-Link 2:IR

P/F

VXXG0316 56h Xh Xh 47h 30h 33h 31h 36h 0Dh 3D Sync Invert

0:Off 1:On

Pn/F

VXXS0316n 56h Xh Xh 53h 30h 33h 31h 36h nh 0Dh 3D Sync Invert

0:Off 1:On

P/F

VXXG0317 56h Xh Xh 47h 30h 33h 31h 37h 0Dh 3D Format

0:Frame

Sequential 1:Top/Bottom 2:Side-By-Side 3:Frame

Packing

Pn/F

VXXS0317n 56h Xh Xh 53h 30h 33h 31h 37h nh 0Dh 3D Format

0:Frame

Sequential 1:Top/Bottom 2:Side-By-Side 3:Frame

Packing

P/F

VXXG0318 56h Xh Xh 47h 30h 33h 31h 38h 0Dh Tilt Angle Warning

0:Off 1:On

Pn/F

VXXS0318 56h Xh Xh 53h 30h 33h 31h 38h nh 0Dh Tilt Angle Warning

0:Off 1:On

P/F

DLP Projector—User’s Manual

— 76 —

Command Group 04 (Remote Control)

ASCII HEX Function Description Return Value

VXXS0401 56h Xh Xh 53h 30h 34h 30h 31h 0Dh UP arrow P/F

VXXS0402 56h Xh Xh 53h 30h 34h 30h 32h 0Dh DOWN arrow P/F

VXXS0403 56h Xh Xh 53h 30h 34h 30h 33h 0Dh LEFT arrow P/F

VXXS0404 56h Xh Xh 53h 30h 34h 30h 34h 0Dh RIGHT arrow P/F

VXXS0405 56h Xh Xh 53h 30h 34h 30h 35h 0Dh POWER P/F

VXXS0406 56h Xh Xh 53h 30h 34h 30h 36h 0Dh EXIT P/F

VXXS0407 56h Xh Xh 53h 30h 34h 30h 37h 0Dh INPUT P/F

VXXS0408 56h Xh Xh 53h 30h 34h 30h 38h 0Dh AUTO P/F

VXXS0409 56h Xh Xh 53h 30h 34h 30h 39h 0Dh KEYSTONE+ P/F

VXXS0410 56h Xh Xh 53h 30h 34h 31h 30h 0Dh KEYSTONE- P/F

VXXS0411 56h Xh Xh 53h 30h 34h 31h 31h 0Dh MENU P/F

VXXS0412 56h Xh Xh 53h 30h 34h 31h 32h 0Dh STATUS P/F

VXXS0413 56h Xh Xh 53h 30h 34h 31h 33h 0Dh MUTE P/F

VXXS0414 56h Xh Xh 53h 30h 34h 31h 34h 0Dh ZOOM+ P/F

VXXS0415 56h Xh Xh 53h 30h 34h 31h 35h 0Dh ZOOM- P/F

VXXS0416 56h Xh Xh 53h 30h 34h 31h 36h 0Dh BLANK P/F

VXXS0417 56h Xh Xh 53h 30h 34h 31h 37h 0Dh FREEZE P/F

VXXS0418 56h Xh Xh 53h 30h 34h 31h 38h 0Dh VOLUME+ P/F

VXXS0419 56h Xh Xh 53h 30h 34h 31h 39h 0Dh VOLUME- P/F

VXXS0420 56h Xh Xh 53h 30h 34h 32h 30h 0Dh Enter P/F

Digital Projection E-Vision Series, 4500 WUXGA User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual