Digital Projection E-Vision, E-Vision Laser 10K Series, E-Vision Laser 8500 Series, E-Vision Laser 7500 Series, E-Vision Laser 8500 WUXGA Important Information Manual

Rev A June 2017

118-156A

E-Vision Laser 4K Series

Important Information

Digital Projection E-Vision Laser 4K Series

Rev A June 2017

Page 2

Important Information

Digital Projection

Digital Projection Asia

16 New Industrial Road
#02-10 Hudson Technocentre
Singapore 536204

Tel [phone]
Fax [phone]

www.digitalprojectionasia.com

Digital Projection Inc.

55 Chastain Road, Suite 115
Kennesaw, GA 30144, USA

Tel [phone]
Fax [phone]

[e-mail]
www.digitalprojection.com

Digital Projection China

中国 北京市 朝阳区 芍药居北里101号
世奥国际中心A座2006室(100029)

Rm A2006
ShaoYaoJu 101 North Lane
Shi Ao International Center
Chaoyang District
Beijing 100029, PR CHINA

Tel [phone]
Fax [phone]

[e-mail]
www.dp-china.com.cn

Digital Projection Limited

Greenside Way, Middleton
Manchester M24 1XX, UK

Registered in England No. 2207264

Registered Ofce: as above

Tel [phone]
Fax [phone]

[e-mail]
[e-mail]

www.digitalprojection.co.uk

Digital Projection E-Vision Laser 4K Series

Rev A June 2017

Page 3

Important Information

Super High Brightness Digital Video Projector

Important Information

Full information about operating, connecting and setting up the projector can be found in the User
Manual, located on the CD.

Updates may be available online - visit the Digital Projection website for all latest documents.

Contents

Symbols used in the User Manual ...............................................................................................4

Electrical and physical specications ........................................................................................5

Laser precautions .............................................................................................................................5

Product labels ....................................................................................................................................6

Label locations ...............................................................................................................................7

Location of laser aperture ..............................................................................................................8

Interlock switches ............................................................................................................................8

General precautions ........................................................................................................................9

Installation precautions ................................................................................................................10

Operation and conguration precautions ...............................................................................11

Compliance with international standards ...............................................................................11

RF Interference .............................................................................................................................11

Noise .............................................................................................................................................11

European Waste Electrical and Electronic Equipment (WEEE) Directive ..............................11

Basic Operation Instructions ......................................................................................................12

Positioning the screen and projector .........................................................................................12

Connecting the power supply .....................................................................................................13

Switching the projector on ..........................................................................................................14

Switching the projector off ..........................................................................................................14

Selecting an input signal .............................................................................................................14

Selecting a test pattern ................................................................................................................15

Adjusting the lens ........................................................................................................................15

Adjusting the image .....................................................................................................................15

Inserting a new lens .....................................................................................................................16

Removing the lens .......................................................................................................................17

Control Panel Reference...............................................................................................................18

Projector indicators .....................................................................................................................19

Remote Control Reference ..........................................................................................................20

Digital Projection E-Vision Laser 4K Series

Rev A June 2017

Page 4

Important Information

Symbols used in the User Manual

LASER WARNING: this symbol indicates that there is a potential hazard of eye
exposure to laser radiation unless the instructions are closely followed.

ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical
shock unless the instructions are closely followed.

WARNING: this symbol indicates that there is a danger of physical injury to yourself
and/or damage to the equipment unless the instructions are closely followed.

NOTE: this symbol indicates that there is some important information that you should read.

Specications are subject to change without notice.

Digital Projection E-Vision Laser 4K Series

Rev A June 2017

Page 5

Important Information

Electrical and physical specications

Main Voltage 100-240 VAC 50/60Hz (Switch selectable)
Operating Temperature 5°C to 40°C (41 F to 104 F)
Storage Temperature -10°C to 60°C (14 F to 140 F)
Operating Humidity 10% to 85% non-condensing
Dimensions: W 500 mm (19.7 in), H 218 mm (8.6 in), D 598 mm (23.5 in)
Weight 29 kg (63.9 lb) without lens
Power Consumption at 100 VAC: 920 W max
at 240 VAC: 880 W max
Standby power: < 6W (normal), <3W (ECO), <0.5W (PowerSAVE)
Thermal Dissipation at 100 VAC: 3139 BTU/Hour max
at 240 VAC: 3002 BTU/Hour max

Laser precautions

CLASS 3R LASER PRODUCT

This Laser Product is designated as Class 3R during all procedures of operation.

LASER LIGHT - AVOID DIRECT EYE EXPOSURE.

Do not point laser or allow laser light to be directed or reected toward other people or

reective objects.

Direct or scattered light can be hazardous to eyes and skin.
There is a potential hazard of eye exposure to laser radiation if the included

instructions are not followed.

Caution – use of controls or adjustments or performance of procedures other than

those specied herein may result in hazardous radiation exposure.

Laser Parameters:

Wavelength 450nm - 460nm (Blue)
Mode of operation Pulsed, due to frame rate
Pulse width 0.74ms
Pulse repetition rate 240Hz
Maximum laser energy 0.376mJ
Total internal power 240Wmax
Apparent source size >10mm, at lens stop
Divergence >100 mili Radian

Digital Projection E-Vision Laser 4K Series

Rev A June 2017

Page 6

Important Information

Product labels

Explanatory Label and Certication Statement Label

2

Complies with FDA performance standards for laser
products except for deviations pursuant to Laser
Notice No. 50, dated June 24, 2007

LASER RADIATION

AVOID DIRECT EYE EXPOSURE

CLASS 3R LASER PRODUCT

Emitted wavelength : 450-460 nm

Max. Pulse energy: 0.376 mJ, Pulse duration: 0.74 ms

激光辐射 避免眼睛受到直接照射 3R类激光产品

波长

: 450-460 nm

最大脉冲能量: 0.376 mJ, 脉冲时间: 0.74 ms

激光輻射 避免眼睛受到直接照射 3R類激光產品

波長: 450-460 nm

最大脈衝能量: 0.376 mJ, 脈衝時間: 0.74 ms

RAYONNEMENT LASER

EXPOSITION DIRECTE DANGEREUSE POUR LES YEUX

APPAREIL À LASER DE CLASSE 3R

longueur d'onde : 450-460nm

maximum énergie de impulsion : 0.376 mJ,

durée de impulsion : 0.74 ms

GB 7247.1-2012 / IEC/EN 60825-1:2007

CLASS 1 LASER PRODUCT

IEC/EN 60825-1:2014

PRODUIT LASER DE CLASSE 1

IEC/EN 60825-1:2014

3264638203

Hazard Warning Symbol and Aperture Label

3

Manufacturer’s ID Label

1

DLP Projector / Projecteur DLP

(

數位投影機/

數字投影機

)

Model/Modèle/

(

型號/型號

) :

AC INPUT/Entrée CA

(

輸入/輸入

) :

100-130 VAC 9.5A 50/60Hz

AC INPUT/Entrée CA

(

輸入/輸入

) :

200-240 VAC 4.5A 50/60Hz

This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
CAN ICES-3(A) /NMB-3(A)

Caution : Do not open the cover. No user-serviceable parts inside
Avertissement : ne pas ouvrir le couvercle. Le produit ne contient
aucune pièce interne réparable par l’utilisateur.

警 告 : 請勿打開外殼,設備內無服務性維修之元件
警 告 : 請勿打開外殼,設備內無服務性維修之元件
警告: 此為A級產品，在生活環境中，該產品可能會造成無線電干擾。

在這種情況下，可能需要用戶對干擾採取切實可行的措施。

制造商:Digital Projection Limited
Greenside Way Middleton
Manchester, M24 1XX UK
(製造地:中國/製造地:中國) Made in China
3264640500 WJ XXXX

KTLZU10002-17005

MSIP-REM-DVP-Laser4K

:

:

:

[phone]

/ :

:

델타 비디오 디스플레이
시스템 (우장) 리미티드

Digital Projection E-Vision Laser 4K Series

Rev A June 2017

Page 7

Important Information

Label locations

1

Location of Manufacturer’s ID Label,

Certication Statement Label and

Explanatory Label on the body of the
projector

4

Serial number

2

Manufacturer’s ID Label
(manufacturer’s name, address and
projector model)

5

Location of Hazard Warning Symbol and
Aperture Label on the body of the projector

3

Certication Statement Label and

Explanatory Label

MENU EXIT

LENS
SHIFT

POWER INPUT ASPECT PIC MUTE

CENTER

LENS

AUTO
SYNC

FOCUS ZOOM

HDMI 2HDMI 1

HDMI1HDMI

2

HDMI3HDMI

4

HDBaseT / LAN Ethernet

3D

SYNC IR

SYNC IN

DisplayPort

RS232

WIRED REMOTE

SYNC OUT

SDI IN SDI OUT

TRIGGER

(1) (2)

ID Label

Part No.: 118-105A

*XXXXXXXXXXXXX*

MANUFACTURED YYYY.MM.DD

Code 39 or 128 of serial no

E-Vision Laser 4K

E-Vision Laser 4KYYYY.MM.DD

TEMP. LIGHT POWERSTATUS

RG2

CAUTION: Do not look into the lens

MENU EXIT

LENS
SHIFT

POWER INPUT ASPECT PIC MUTE

CENTER

LENS

AUTO
SYNC

FOCUS ZOOM

HDMI 2HDMI 1

HDMI1HDMI

2

HDMI3HDMI

4

HDBaseT / LAN Ethernet

3D

SYNC IR

SYNC IN

DisplayPort

RS232

WIRED REMOTE

SYNC OUT

SDI IN SDI OUT

TRIGGER

(1) (2)

ID Label

Part No.: 118-105A

*XXXXXXXXXXXXX*

MANUFACTURE D YYYY.MM.DD

Code 39 or 128 of serial no

E-Vision Laser 4K

E-Vision Laser 4KYYYY.MM.DD

2

4

3

5

1

Digital Projection E-Vision Laser 4K Series

Rev A June 2017

Page 8

Important Information

Location of laser aperture

The laser aperture is located as indicated below.

1

Laser aperture

Interlock switches

Three interlock switches installed at the main frame, inside the cover, will power-off the system
individually when activated.

1

Will be activated when the top cover is removed.

2

x2. Will be activated when the projection lens is removed.

1

1

2

2

Digital Projection E-Vision Laser 4K Series

Rev A June 2017

Page 9

Important Information

General precautions

The unit is never to be operated if the unit is defective or the cover or seal is damaged.

No maintenance allowed by end user.

Do not open the cabinet. There are no user serviceable parts inside.

No service is allowed except by authorized personnel.

Use only the power cable provided.

Ensure that the power outlet includes a Ground connection, as this equipment MUST be

earthed.

Take care to prevent small objects such as paper or wire from falling into the projector.

If this does happen, switch off immediately, and have the objects removed by
authorised service personnel.

Do not expose the projector to rain or moisture, and do not place any liquids on top of

the projector.
Unplug before cleaning, and use a damp, not wet, cloth.
Do not touch the power plug with wet hands.
Do not touch the power plug during a thunder storm.

Handle the power cable carefully and avoid sharp bends. Do not use a damaged power

cable.

Do not touch the ventilation outlets, as they will become hot in use.

Do not cover or obstruct the ventilation outlets or inlets.

Do not cover the lens whilst the projector is switched on. This could cause a re

Always allow the projector to cool for 5 minutes before disconnecting the power or

moving the projector.

Never use strong detergents or solvents such as alcohol or thinners to clean the

projector and lens.
RISK GROUP 2 CAUTION. Possibly hazardous optical radiation emitted from this

product. Do not stare at operating light source. May be harmful to the eyes.

RG2

CAUTION: Do not look into the lens

Digital Projection E-Vision Laser 4K Series

Rev A June 2017

Page 10

Important Information

Installation precautions

Connect the LAN cable only to a computer LAN connection. Other similar connectors

may have a dangerously high voltage source.

The projector must be installed only by suitably qualied personnel, in accordance with

local building codes.
The projector should be installed as close to the power outlet as possible.
The power connection should be easily accessible, so that it can be disconnected in an

emergency.

Ensure that there is at least 50cm (19.7in) of space between the ventilation outlets and

any wall, and 30cm (11.8in) on all other sides.
Do not install the projector close to anything that might be affected by its operational

heat, for instance, polystyrene ceiling tiles, curtains etc.

Place the projector in a dry area away from sources of dust, moisture, steam, smoke,

sunlight or heat.

The projector is heavy. Use safe handling techniques when lifting the projector.

Do not drop or knock the projector.
Before installation, make sure that the surface, ceiling or rigging that is to support the

projector is capable of supporting the combined weight of the projector and lens.

When stacking projectors, the stack MUST be vertical, to ensure that the stresses are

distributed to all four chassis corners.
Do not stack more than 3 projectors.

Do not place heavy objects on top of the projector chassis. Only the chassis corners

and the optional rigging frame are capable of withstanding the weight of another

projector.
Backup safety chains or wires should always be used with ceiling mount installations.
The projector can be operated in any position. It is recommended to position the

projector in portrait mode with inputs facing upward, as shown in the diagram:

1

Recommended positions: inputs side up

2

Also possible

Pitch

360°

2

30°

330°

2

1

Roll

Digital Projection E-Vision Laser 4K Series

Rev A June 2017

Page 11

Important Information

Operation and conguration precautions

Do not make changes to the networking conguration unless you understand what you

are doing, or have taken advice from your Network Manager. If you make a mistake,

it is possible that you will lose contact with the projector. Always double-check your

settings before pressing the APPLY button. Always keep a written note of the original

settings, and any changes you have made.

Software update should NOT be carried out except by, or with the supervision of, Digital

Projection Service personnel.

Compliance with international standards

RF Interference

FCC

The Federal Communications Commission does not allow any modications or changes to the unit
EXCEPT those specied by Digital Projection in this manual. Failure to comply with this government

regulation could void your right to operate this equipment.

This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant with Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area may cause harmful interference, in which case the
user will be responsible for correcting any interference.

Noise

GSGV Acoustic Noise Information Ordinance

The sound pressure level is less than 43 dB (A) according to ISO 3744 or ISO 7779.

European Waste Electrical and Electronic Equipment (WEEE) Directive

Digital Projection Ltd is fully committed to minimising Waste Electrical and Electronic
Equipment. Our products are designed with reuse, recycling and recovery of all components
in mind. To this end, at end of life, your projector may be returned to Digital Projection Ltd or
its agent so that the environmental impact can be minimised.

Digital Projection E-Vision Laser 4K Series

Rev A June 2017

Page 12

Important Information

Basic Operation Instructions

Positioning the screen and projector

1. Install the screen, ensuring that it is in the best position for viewing by your audience.

2. Mount the projector, ensuring that it is at a suitable distance from the screen for the image to ll

the screen. Set the adjustable feet so that the projector is level, and perpendicular to the screen.

The drawing below shows the positions of the feet for table mounting, and the xing holes for ceiling

mounting.

1

Four adjustable feet

2

Six M4 holes for ceiling mount

The screws should not penetrate more than 15 mm into the body of the projector.

1

2

1

1

1

2

2

2

2

2

Digital Projection E-Vision Laser 4K Series

Rev A June 2017

Page 13

Important Information

Connecting the power supply

Adjust the VOLTAGE SELECT switch 1 to the required voltage, then rmly push the mains
connector into the socket 2.

Voltage selection

The VOLTAGE SELECT switch must be set to match the power supply you are using:

Voltage of power supply used Position of VOLTAGE SELECT switch

100-130VAC outlet

200-240VAC (single phase) outlet

Use only the power cable provided.

Ensure that the power outlet includes a ground connection as this equipment MUST be

earthed.

Handle the power cable carefully and avoid sharp bends. Do not use a damaged power

1

2

Digital Projection E-Vision Laser 4K Series

Rev A June 2017

Page 14

Important Information

cable.

Switching the projector on

1. Connect the power cable between the mains supply and the projector. (See Connecting the

power supply above.) Switch on at the switch next to the power connector.

2. The POWER indicator lights red to signal that the projector is in STANDBY mode. Press one of

the following buttons:

• On the remote control, the ON button

• On the projector control panel, the POWER button.

The fans begin working, then the POWER indicator begins ashing green. When the ashing
stops, the POWER and LIGHT indicators both light steady green. The projector is switched on.

Switching the projector off

1. Press OFF on the remote control or POWER on the control panel, then press again to conrm

your choice.

The POWER indicator on the control panel will start ashing amber, the system will go out and the
cooling fans will run for a short time until the POWER indicator goes steady red to indicate that the
projector has entered STANDBY mode.

2. If you need to switch the projector off completely, switch off at the mains power switch next to the

power connector and then disconnect the power cable from the projector.

Selecting an input signal

1. Connect one or more image sources to the projector.

2. Select the input you want to display:

• Press one of the input buttons on the remote control.

• Alternatively, open the On-screen display (OSD) by pressing MENU. Highlight Input from the

main menu, press ENTER/OK and then select an input signal using the UP and DOWN arrow
buttons. Press ENTER/OK to conrm your choice.

Digital Projection E-Vision Laser 4K Series

Rev A June 2017

Page 15

Important Information

Selecting a test pattern

To display a test pattern:

• Press TEST on the remote control. If necessary, press again to change the test pattern. Test

patterns are displayed in the following order:

White, Black, Red, Green, Blue, Cyan, Yellow, Magenta, Off

After the nal test pattern, the projector exits test pattern mode and returns to the main image. To

view test patterns again, you need to press TEST again.

• Alternatively, open the OSD by pressing MENU. Highlight Test Patterns from the main menu,

then select a test pattern using the LEFT and RIGHT arrow buttons.

Adjusting the lens

The lens can be adjusted using the Lens menu, or using the lens buttons on the remote control.

Lens menu

The Lens menu provides access to the Lens Control setting and the Center Lens command.

Lens Control allows Zoom, Focus and Shift adjustment using the arrow buttons. The setting

operates in Zoom/Focus Adjustment and Shift Adjustment mode.

Press ENTER/SELECT to switch between the two modes.

Remote control

Use the remote control to adjust zoom, focus and shift directly, without opening a menu:

• OK enters lens control, then switches between Zoom/Focus Adjustment and Shift Adjustment.

• EXIT exits lens control and opens the Lens menu.

• MENU exits lens control and returns to the main image.

• The arrow buttons adjust zoom, focus and shift as indicated on the screen.

Adjusting the image

Orientation

• This can be set from the Setup menu.

Highlight Projector Mode and choose from Front Tabletop, Front Ceiling, Rear Tabletop, Rear

Ceiling and Auto-front.

Keystone

• This can be set from the Geometry menu.

Picture

• Settings such as Gamma, Brightness, Contrast, Saturation, Hue and Sharpness can be set

from the Image menu.

Digital Projection E-Vision Laser 4K Series

Rev A June 2017

Page 16

Important Information

Inserting a new lens

Before changing the lens, always make sure the projector is switched off and fully

disconnected from its power supply.

When changing the lens, avoid using excessive force as this may damage the

equipment.

The lens is shipped separately.

Take care to preserve the original lens packaging and protective caps for future use.

The projector will not power on without the lens tted.

1. Remove the lens cap.

2. Position the lens so that the labels are at the top, and gently insert it all the way into the lens

mount.

3. Push the lens in rmly, and turn it clockwise until it clicks into place.

Digital Projection E-Vision Laser 4K Series

Rev A June 2017

Page 17

Important Information

Removing the lens

Before changing the lens, always make sure the projector is switched off and fully

disconnected from its power supply.

When changing the lens, avoid using excessive force as this may damage the

equipment.

The lens is shipped separately.

Take care to preserve the original lens packaging and protective caps for future use.

The projector will not power on without the lens tted.

1. Push in the lens release lever, and turn the lens anti-clockwise.

2. Remove the lens.

Digital Projection E-Vision Laser 4K Series

Rev A June 2017

Page 18

Important Information

Control Panel Reference

AUTO SYNC and ASPECT do not work when the projector uses HDMI 3 or 4.

POWER

INPUT

AUTO

SYNC

ASPECT

CENTER

LENS

PIC MUTE

1 2 3 4 5 6

7 8 9 10 11 12

Digital Projection E-Vision Laser 4K Series

Rev A June 2017

Page 19

Important Information

1

POWER

Switches the projector on and off (STANDBY).

2

INPUT

Switches to the next input source.

3

AUTO SYNC

Re-synchronises with the current input signal.

4

ASPECT

Changes the aspect ratio.

5

CENTER LENS

Centers the lens.

6

PIC MUTE

Switches the laser off/on.

7

MENU

Displays and exits the OSD.

8

Arrow buttons & ENTER

Navigation buttons used to highlight menu entries in the OSD.
Press ENTER to open or execute the highlighted menu entry.

9

EXIT

Exits the current OSD page and enters the level above.

10

LENS SHIFT arrow buttons

Each of these buttons moves the lens in the specied direction.

11

FOCUS plus and minus buttons

Used to move the focus in and out.

12

ZOOM plus and minus buttons

Used to zoom in and out.

Projector indicators

TEMP. Off = no problem
Flashing red = temperature error

LIGHT Off = light is switched off
Flashing green = light is preparing to switch on
Flashing red (cycles of six ashes) = light module failure
On, red = light module has reached end of life
On, green = light is switched on

STATUS Off = no problem
Flashing red (continuously) = cover error
Flashing red (cycles of four ashes) = fan error
On, red = system error

POWER Off = the projector is switched off
Flashing green = the projector is warming up
Flashing amber = the projector is cooling down
On, red = STANDBY mode
On, green = the projector is switched on

POWERSTAT U SLIGHTTEMP.

Digital Projection E-Vision Laser 4K Series

Rev A June 2017

Page 20

Important Information

Remote Control Reference

1

Power ON/OFF

Turns the projector on and off.
To turn the projector off, press the

OFF button twice within ve seconds.

2

Pic Mute OPEN / CLOSE

Shows and hides the projected image.

3

OSD ON / OFF

Enables and disables screen timeout
messages and showing the OSD
during projection.

4

MENU

Access the projector OSD (on-screen
display). If the OSD is open, press
this button to go back to the previous
menu.

5

Navigation (arrows and OK)

Navigate through the menus with the
arrows, conrm your choice with OK.
In lens adjustment modes, the arrows
are used to move, zoom or focus the
lens. See 11 below.
In lens adjustment modes, or when
the OSD is not showing, the OK
button switches between modes:

Shift Adjustment and Zoom /
Focus Adjustment.

6

EXIT

Close the current OSD page and
return to the level above.

7

FREEZE

Freeze the current frame.

8

DEFAULT

Restore default settings.

9

INFO

Access information about the
projector.

10

RE-SYNC

Re-synchronise with the current input
signal.

Pic Mute

MENU

EXIT INFO

HDMI1

OK

OFF ON

ALT

LENS

FOCUS ZOOM

IN

OUT

IN

OUT

SHIFT

21 3

HDMI2 DVI

HD-T

VGA COMP1 COMP2 TEST

R G B ALL

3D EYE PIP SWAP

4 5 6

7 8 9 0

ALT

ADDR

OSD

OFF

ON

DEFAULT

FREEZE

RE-SYNC

A B C D

USER PRESET

OPEN CLOSE

HDMI3

HDMI4

DisplayPort2

DisplayPort1

SDI

1

2

5

6

8

4

9

7

3

10

Digital Projection E-Vision Laser 4K Series

Rev A June 2017

Page 21

Important Information

11

LENS adjustment

FOCUS IN / OUT: adjust focus.
SHIFT: press and hold this button,

then use the Navigation arrow
buttons to move the lens.

ZOOM IN / OUT: adjust zoom.

12

USER PRESET A, B, C, D

Load user presets.

13

ALT

Press and hold this button to
access alternative functions for all
buttons with a green label.

14

DVI / DisplayPort2 / numeric

input 3

There is no DVI input on this
projector.
Use with ALT to switch to the
DisplayPort 2 input.

15

HDMI 2 / HDMI 4 / numeric input 2

Select the HDMI 1 input.
Use with ALT to switch to the HDMI
4 input.

16

HDMI 1 / HDMI 3 / numeric input 1

Select the HDMI 1 input.
Use with ALT to switch to the HDMI
3 input.

17

TEST / SWAP / numeric input 0

Show a test pattern. Press again to
show the next test pattern:
...Off, White, Black, Red, Green,

Blue, Cyan, Yellow, Magenta,
Off...

FREEZE and RE-SYNC are not

available when the projector uses

input HDMI 3 or 4.

3D is only available on the HDMI 3

and 4 inputs.

This projector does not use the

following options on the remote:

DVI, VGA, COMP 1 and COMP 2.

Pic Mute

MENU

EXIT INFO

HDMI1

OK

OFF ON

ALT

LENS

FOCUS ZOOM

IN

OUT

IN

OUT

SHIFT

21 3

HDMI2 DVI

HD-T

VGA COMP1 COMP2 TEST

R G B ALL

3D EYE PIP SWAP

4 5 6

7 8 9 0

ALT

ADDR

OSD

OFF

ON

DEFAULT

FREEZE

RE-SYNC

A B C D

USER PRESET

OPEN CLOSE

HDMI3

HDMI4

DisplayPort2

DisplayPort1

SDI

13

11

12

14

15

16

17

Digital Projection E-Vision Laser 4K Series

Rev A June 2017

Page 22

Important Information

18

DisplayPort1 /R/ numeric input 4

Select the DisplayPort 1 input.

19

HD-T /G/ numeric input 5

Select the HDBaseT input.

20

SDI /B/ numeric input 6

Select the 3G-SDI input.

21

VGA /3D/ numeric input 7

There is no VGA input on this
projector.
Use with ALT to toggle the 3D

Format setting between Off and
Auto.

22

COMP1 /EYE/ numeric input 8

There is no Component 1 input on
this projector.
Use with ALT to switch between left
and right eye 3D dominance.

23

COMP2 /PIP/ numeric input 9

There is no Component 1 input on
this projector.

24

ADDR / ALL

Assign and unassign an IR remote
address.

To assign an address:

1. Press and hold this button
until the indicator starts

ashing.

2. Release this button and while

the indicator is still ashing,

enter a two-digit address
using the numeric input
buttons. The indicator will

ash three times quickly to
conrm the change.

To unassign an address and
return to the default address 00,

• Press and hold ALT and

this button simultaneously

until the indicator ashes to
conrm the change.

3D is only available on the HDMI 3

and 4 inputs.

This projector does not use the

following options on the remote:

DVI, VGA, COMP 1 and COMP 2.

Pic Mute

MENU

EXIT INFO

HDMI1

OK

OFF ON

ALT

LENS

FOCUS ZOOM

IN

OUT

IN

OUT

SHIFT

21 3

HDMI2 DVI

HD-T

VGA COMP1 COMP2 TEST

R G B ALL

3D EYE PIP SWAP

4 5 6

7 8 9 0

ALT

ADDR

OSD

OFF

ON

DEFAULT

FREEZE

RE-SYNC

A B C D

USER PRESET

OPEN CLOSE

HDMI3

HDMI4

DisplayPort2

DisplayPort1

SDI

24

19

20

18

21

22

23