Digital Projection E-Vision Laser 4K-UHD HB, E-Vision Laser 5000, E-Vision LASER WQ-120 User Manual
E-Vision Laser 4K Series
High Brightness Digital Video Projector
4INSTALLATION AND QUICK-START GUIDE
4CONNECTION GUIDE
4OPERATING GUIDE
4REFERENCE GUIDE
Rev B December 2017
118-157B
Digital Projection E-Vision Laser 4K Series
About This Document
Follow the instructions in this manual carefully to ensure safe and long-lasting use of the projector.
Symbols used in this manual
Many pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:
WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless
the instructions are closely followed.
ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely
followed.
LASER WARNING: this symbol indicates that there is a potential hazard of eye exposure to laser radiation unless the
instructions are closely followed.
NOTE: this symbol indicates that there is some important information that you should read.
Product revision
Because we at Digital Projection continually strive to improve our products, we may change specications and designs, and add new features
without prior notice.
Updates may be available online - visit the Digital Projection website for all latest documents.
Notes
Legal notice
Trademarks and trade names mentioned in this document remain the property of their respective owners.
Digital Projection disclaims any proprietary interest in trademarks and trade names other than its own.
Copyright © 2017 Digital Projection Ltd. All rights reserved.
Rev B December 2017
page i
Digital Projection E-Vision Laser 4K Series
Laser Information
LASER LIGHT
AVOID DIRECT EYE EXPOSURE
CLASS 3R LASER PRODUCT
455-470nm <13Watts
CLASSIFIED EN/IEC 60825-1 2007
Caution-useofcontrolsoradjustmentsorperformanceofproceduresotherthanthosespeciedhereinmayresultin
hazardous radiation exposure.
Optical radiation
CAUTION: Do not look into the lens
RG2
Notes
Notes
Caution - possibly hazardous optical radiation emitted from this product. Do not stare at operating light source. May be
harmful to eyes. This projector is tested according to IEC/EN62471-5:2015 (Photobiological safety of lamps and lamp
systems – Part 5: Image projectors” standard) to be Risk Group 2 (low risk).
Rev B December 2017
page ii
Digital Projection E-Vision Laser 4K Series
Introduction
Congratulations on your purchase of this Digital Projection product.
Your projector has the following key features:
• Displays 4K-UHD with smooth picture processing
• Displays WQXGA+ (2716x1528) with smooth picture off.
• Support for Frame Sequential and Dual Pipe 3D formats.
• HDBaseT® for transmission of uncompressed High Denition Video up to 100 m from the source.
• 3G-SDI with loop-through.
• Edge Blend.
• Blanking control for custom input window sizing.
• Cornerstone, Vertical & Horizontal Keystone, Pincushion & Barrel, and Image Rotation.
• Separate control of screen and source aspect ratio.
• Control via LAN and RS232.
• Motorised lens mount.
Notes
A serial number is located on the side of the projector. Record it here:
Rev B December 2017
page iii
Digital Projection E-Vision Laser 4K Series
CONTENTS
INSTALLATION AND QUICK-START GUIDE ..............................1
WHAT’S IN THE BOX? ................................................................... 3
CONNECTING THE POWER SUPPLY ............................................. 4
Voltage selection ................................................................................... 4
PROJECTOR OVERVIEW ............................................................... 5
Front and rear views ............................................................................. 5
Control panel ......................................................................................... 6
Projector indicators ................................................................................ 7
REMOTE CONTROL ....................................................................... 8
Infrared reception ................................................................................ 11
POSITIONING THE SCREEN AND PROJECTOR ........................... 12
Roll and pitch ...................................................................................... 13
CHANGING THE LENS ................................................................. 14
Inserting a new lens ............................................................................ 14
Removing the lens .............................................................................. 14
OPERATING THE PROJECTOR .................................................... 15
Switching the projector on ................................................................... 15
Switching the projector off ................................................................... 15
Selecting an input signal ..................................................................... 16
Selecting a test pattern ....................................................................... 16
Adjusting the lens ................................................................................ 17
Adjusting the image............................................................................. 17
CONNECTION GUIDE ............................................................................19
SIGNAL INPUTS .......................................................................... 21
Digital inputs and outputs .................................................................... 21
EDID on the DisplayPort, HDMI and HDBaseT inputs ........................ 22
Using DisplayPort/HDMI/HDBaseT switchers with the projector ........ 22
3D connections ................................................................................... 23
Frame sequential 1080p 3D up to 120Hz and WUXGA 3D at 100Hz ................ 23
Dual Pipe 1080p, WUXGA and WQXGA+ 3D sources at up to 100 and 120 Hz ... 23
3D Sync............................................................................................... 24
3D Sync In ......................................................................................... 24
3D Sync Out ....................................................................................... 24
3D Sync IR ........................................................................................ 24
CONTROL CONNECTIONS ........................................................... 25
LAN connection examples .................................................................. 26
RS232 connection example ............................................................... 27
Rev B December 2017
page iv
Digital Projection E-Vision Laser 4K Series
CONTENTS (continued)
OPERATING GUIDE ................................................................................29
USING THE MENUS ..................................................................... 31
Opening the OSD ................................................................................ 31
Opening a menu.................................................................................. 31
Exiting menus and closing the OSD.................................................... 31
Inside a menu...................................................................................... 32
Accessing sub-menus ........................................................................... 32
Executing commands............................................................................ 32
Editing projector settings ..................................................................... 33
Using a slider to set a value .................................................................... 33
Editing numeric values .......................................................................... 33
USING THE PROJECTOR ............................................................. 34
Main menu .......................................................................................... 34
Lens menu .......................................................................................... 35
Lens Control ....................................................................................... 35
Lens Memory ...................................................................................... 36
Image menu ........................................................................................ 37
Color menu.......................................................................................... 39
Color Space ....................................................................................... 39
Color Mode ........................................................................................ 40
Geometry menu .................................................................................. 45
Aspect Ratio ....................................................................................... 45
Digital Zoom ....................................................................................... 47
Overscan ........................................................................................... 48
Blanking ............................................................................................ 49
Keystone ........................................................................................... 50
4 Corners .......................................................................................... 52
Rotation ............................................................................................ 53
Pincushion / Barrel ............................................................................... 54
Custom Warp ..................................................................................... 55
Arc ................................................................................................... 56
Edge Blend menu................................................................................ 57
Blend Width........................................................................................ 58
Black Level Uplift ................................................................................. 59
3D menu.............................................................................................. 60
3D types ............................................................................................ 61
Some 3D settings explained ................................................................... 62
Laser menu ......................................................................................... 63
Setup menu ......................................................................................... 64
ColorMax ........................................................................................... 67
Power On/Off ...................................................................................... 68
Clock Adjust ....................................................................................... 69
OSD Settings ...................................................................................... 70
Memory ............................................................................................. 70
Network menu ..................................................................................... 71
PIP menu ............................................................................................ 72
Information menu ................................................................................ 73
Signal Format ..................................................................................... 73
System Status .................................................................................... 74
Thermal Status.................................................................................... 74
Factory Reset ..................................................................................... 75
SERVED WEB PAGES .................................................................. 76
CHOOSING A LENS ..................................................................... 89
Rev B December 2017
page v
Digital Projection E-Vision Laser 4K Series
CONTENTS (continued)
Basic calculation ................................................................................. 90
Basic calculation example ................................................................... 91
Full lens calculation ............................................................................. 92
Introducing TRC .................................................................................. 92
Calculating TRC .................................................................................. 93
Calculating the throw ratio with TRC ......................................................... 94
Full lens calculation example .............................................................. 95
POSITIONING THE IMAGE ........................................................... 96
APPENDIX A: LENS PART NUMBERS .......................................... 98
APPENDIX B: SUPPORTED SIGNAL INPUT MODES .................... 99
2D formats........................................................................................... 99
SDI formats ....................................................................................... 102
3D formats......................................................................................... 103
APPENDIX C: WIRING DETAILS ................................................ 104
RS232 ............................................................................................... 104
Trigger 1 & Trigger 2 ......................................................................... 105
Wired remote control ......................................................................... 105
Sync IN, Sync OUT and 3D Sync IR ................................................. 105
APPENDIX D: GLOSSARY OF TERMS ....................................... 106
Rev B December 2017
page vi
Digital Projection E-Vision Laser 4K Series
This page is intentionally left blank.
E-Vision Laser 4K Series
High Brightness Digital Video Projector
4
INSTALLATION AND QUICK-START GUIDE
Rev B December 2017
Digital Projection E-Vision Laser 4K Series
CONTENTS
CONTENTS
WHAT’S IN THE BOX? .............................................................................3
CONNECTING THE POWER SUPPLY .............................................4
VOLTAGE SELECTION ................................................................... 4
PROJECTOR OVERVIEW .......................................................................5
FRONT AND REAR VIEWS ............................................................. 5
CONTROL PANEL .......................................................................... 6
Projector indicators ............................................................................... 7
REMOTE CONTROL ..................................................................................8
OPERATING THE PROJECTOR ........................................................15
SWITCHING THE PROJECTOR ON .............................................. 15
SWITCHING THE PROJECTOR OFF ............................................. 15
SELECTING AN INPUT SIGNAL ................................................... 16
SELECTING A TEST PATTERN..................................................... 16
ADJUSTING THE LENS ................................................................ 17
ADJUSTING THE IMAGE .............................................................. 17
INFRARED RECEPTION ............................................................... 11
POSITIONING THE SCREEN AND PROJECTOR ...................12
ROLL AND PITCH ........................................................................ 13
CHANGING THE LENS ..........................................................................14
INSERTING A NEW LENS ............................................................ 14
REMOVING THE LENS ................................................................. 14
Installation and Quick-Start Guide
Rev B December 2017
Digital Projection E-Vision Laser 4K Series
PicMute
OPEN
CLOSE
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DisplayPort1
HD-T 3GSDI
VGA COMP1 COMP2
HDMI3
TEST
HDMI4
DisplayPort2
R G B ALL
3D EYE PIP SWAP
4 5 6
7 8 9 0
ALT
ADDR
OSD
OFF
ON
DEFAULT
FREEZE
RE-SYNC
A B C D
USERPRESET
WHAT’S IN THE BOX?
What’s In The Box?
Remote control
2x AAA batteries
Security screw
Projector
Notes
Make sure your box contains
everything listed. If any pieces are
missing, contact your dealer.
You should save the original box
and packing materials, in case you
ever need to ship your projector.
The projector is shipped without a
lens.
Only one power cable - dependent
on the destination territory - will be
supplied with the projector.
User Manual on disc Important Information
Power cable, United Kingdom
Installation and Quick-Start Guide
HDMI cable
Power cable, Europe Power cable, North America
Power cable, China
Rev B December 2017
page 3
Digital Projection E-Vision Laser 4K Series
CONNECTING THE POWER SUPPLY
Connecting The Power Supply
Adjust the VOLTAGE SELECT switch 1 to the required voltage, then rmly push the mains connector into the socket 2.
1
2
Voltage selection
The VOLTAGE SELECT switch must be set to match the power supply you are using:
Voltage of power supply used Position of VOLTAGE SELECT switch
AC100-130V outlet
Notes
Use only the power cable
provided.
Ensure that the power outlet
includes a ground connection as
this equipment MUST be earthed.
Handle the power cable carefully
and avoid sharp bends. Do not
use a damaged power cable.
AC200-240V (single phase) outlet
Installation and Quick-Start Guide
Rev B December 2017
page 4
Digital Projection E-Vision Laser 4K Series
PROJECTOR OVERVIEW
Projector Overview
Front and rear views
Air inlet
1
Front infrared window and indicators
2
Air inlet
3
Lens mount
4
Rear infrared window
5
Air outlet
6
Connections panel
7
Control panel
8
Adjustable feet
9
Voltage selector
10
Mains socket and switch
11
1
2
4
3
Notes
Front view
5
9
Rear view
76
8
1110
Air inlets
12
Installation and Quick-Start Guide
12
Bottom view
Rev B December 2017
page 5
Digital Projection E-Vision Laser 4K Series
PROJECTOR OVERVIEW
Control panel
POWER
1
2
3
4
5
6
7
8
9
10
11
12
Switches the projector on and off
(STANDBY).
INPUT
Switches to the next input source.
AUTO SYNC
Re-synchronises with the current input
signal.
ASPECT
Changes the aspect ratio.
CENTER LENS
Centers the lens.
PIC MUTE
Shows and hides the projected image.
When OFF, the light source is completely
switched off and the screen is black.
MENU
Displays and exits the OSD.
Arrow buttons & ENTER
Navigation buttons used to highlight menu
entries in the OSD.
Press ENTER to open or execute the
highlighted menu entry.
EXIT
Exits the current OSD page and enters the
level above.
LENS SHIFT arrow buttons
Each of these buttons moves the lens in the
specied direction.
FOCUS plus and minus buttons
Used to move the focus in and out.
ZOOM plus and minus buttons
Used to zoom in and out.
1 2 3 4 5 6
POWER
7 8 9 10 11 12
INPUT
AUTO
SYNC
ASPECT
CENTER
LENS
PIC MUTE
Notes
AUTO SYNC and ASPECT do not
work when the projector uses HDMI
3 or 4.
Installation and Quick-Start Guide
Rev B December 2017
page 6
Digital Projection E-Vision Laser 4K Series
PROJECTOR OVERVIEW
Projector indicators
TEMP. Off = no problem
Flashing red = temperature error
LIGHT Off = light is switched off
Flashing green = light is preparing to switch on
Flashing red (cycles of six ashes) = light module failure
On, red = light module has reached end of life
On, green = light is switched on
STATUS Off = no problem
Flashing red (continuously) = cover error
Flashing red (cycles of four ashes) = fan error
On, red = system error
POWER Off = the projector is switched off
Flashing green = the projector is warming up
Flashing amber = the projector is cooling down
On, red = STANDBY mode
On, green = the projector is switched on
Notes
POWERSTATU SLIGHTTEMP.
Installation and Quick-Start Guide
Rev B December 2017
page 7
Digital Projection E-Vision Laser 4K Series
REMOTE CONTROL
Remote Control
1
Power ON / OFF
Turns power on and off.
2
Pic Mute OPEN / CLOSE
Shows and hides the projected image.
When OFF, the light source is completely switched off and the screen is black.
2
OSD ON / OFF
Enable and disable screen timeout messages and control whether to show the OSD
during projection.
4
MENU
Access the OSD. If the OSD is open, press this button to go back to the previous menu.
5
Navigation (arrows and OK)
Navigate through the menus with the arrows, conrm your choice with OK.
In lens adjustment modes, the arrows are used to move, zoom or focus the lens. See 11
below.
In lens adjustment modes, or when the OSD is not showing, the OK button switches
between modes: Shift Adjustment and Zoom / Focus Adjustment.
6
EXIT
Go up one level in the OSD. When the top level is reached, press to close the OSD.
7
FREEZE
Freeze the current frame.
8
DEFAULT
When editing a parameter, press this button to restore the default value.
9
INFO
Access information about the projector.
10
RE-SYNC
Re-synchronise with the current input signal.
Notes
OFF ON
1
Pic Mute
2
3
4
5
6
7
OPEN
OFF
MENU
EXIT INFO
FREEZE
FOCUS ZOOM
IN
OUT
USER PRESET
CLOSE
OSD
ON
DEFAULT
8
OK
9
RE-SYNC
10
LENS
IN
SHIFT
OUT
A B C D
HDMI2 DVI
HDMI1
HDMI3
DisplayPort1
21 3
DisplayPort2
HDMI4
HD-T 3GSDI
ALT
ALT
ADDR
4 5 6
R G B ALL
VGA COMP1 COMP2
7 8 9 0
3D EYE PIP SWAP
TEST
FREEZE and RE-SYNC are not
available when the projector uses
input HDMI 3 or 4.
3D is only available on the HDMI 3
and 4 inputs.
This projector does not use the
following options on the remote:
DVI, VGA, COMP 1 and COMP 2.
continues on next page...
Installation and Quick-Start Guide
Remote control
Rev B December 2017
page 8
MENU
EXIT INFO
OK
OSD
OFF
ON
DEFAULT
Digital Projection E-Vision Laser 4K Series
11
LENS adjustment
FOCUS IN / OUT: adjust focus.
SHIFT: press and hold this button, then use the Navigation arrow
buttons to move the lens.
ZOOM IN / OUT: adjust zoom.
12
USER PRESET A, B, C, D
Load user presets.
13
ALT
14
Press and hold this button to access alternative functions for all
buttons with a green label.
DVI / DisplayPort2 / numeric input 3
There is no DVI input on this projector.
Use with ALT to select the DisplayPort 2 input.
15
HDMI 2 / HDMI 4 / numeric input 2
Select the HDMI 1 input.
Use with ALT to select the HDMI 4 input.
16
HDMI 1 / HDMI 3 / numeric input 1
Select the HDMI 1 input.
Use with ALT to select the HDMI 3 input.
17
TEST / SWAP / numeric input 0
Show a test pattern. Press again to show the next test pattern:
...Off, White, Black, Red, Green, Blue, CheckerBoard,
CrossHatch, V Burst, H Burst, ColourBar, Screen layout.
When PIP mode is on, use this button with ALT to swap the main and
sub images.
REMOTE CONTROL
FREEZE
FOCUS ZOOM
11
12
IN
OUT
A B C D
HDMI1
HDMI3
DisplayPort1
4 5 6
R G B ALL
VGA COMP1 COMP2
7 8 9 0
3D EYE PIP SWAP
LENS
SHIFT
USER PRESET
HDMI2 DVI
21 3
HDMI4
DisplayPort2
HD-T 3GSDI
RE-SYNC
IN
OUT
ALT
ALT
ADDR
TEST
Notes
3D is only available on the HDMI 3
and 4 inputs.
This projector does not use the
following options on the remote:
DVI, VGA, COMP 1 and COMP 2.
13
14
15
16
17
continues on next page...
Installation and Quick-Start Guide
Remote control
Rev B December 2017
page 9
Pic Mute
OPEN
CLOSE
MENU
EXIT INFO
OK
LENS
FOCUS ZOOM
OSD
OFF
ON
DEFAULT
FREEZE
RE-SYNC
Digital Projection E-Vision Laser 4K Series
17
DISPLAYPORT 1 / R / numeric input 4
18
HD-T / G / numeric input 5
Select DisplayPort 1 input.
Select the HDBaseT input.
REMOTE CONTROL
OFF ON
Notes
PIP is not available when the
projector uses input HDMI 3 or 4.
19
3GSDI / B / numeric input 6
Select the 3G-SDI input.
20
VGA / 3D / numeric input 7
There is no VGA input on this projector.
Use with ALT to toggle the 3D Format setting between Off and Auto.
21
COMP1 / EYE / numeric input 8
22
23
There is no Component 1 input on this projector.
Use with ALT to switch between left and right eye 3D dominance.
COMP2 / PIP / numeric input 9
There is no Component 2 input on this projector.
Use with ALT to switch on Picture In Picture (PIP) mode.
ADDR / ALL (with red indicator at the top)
Assign and unassign an IR remote address.
To assign an address:
1. Press and hold this button until the indicator starts ashing.
2. Release this button and while the indicator is still ashing, enter
a two-digit address using the numeric input buttons. The indicator
will ash three times quickly to conrm the change.
To unassign an address and return to the default address 00,
• Press and hold ALT and this button simultaneously until the
indicator ashes to conrm the change.
17
18
19
20
21
22
Pic Mute
OPEN
CLOSE
OSD
Remote control top
IN
SHIFT
OUT
USER PRESET
A B C D
HDMI1
HDMI2 DVI
21 3
HDMI3
DisplayPort1
DisplayPort2
HDMI4
HD-T 3GSDI
4 5 6
R G B ALL
VGA COMP1 COMP2
7 8 9 0
3D EYE PIP SWAP
3D is only available on the HDMI 3
and 4 inputs.
This projector does not use the
following options on the remote:
DVI, VGA, COMP 1 and COMP 2.
IN
OUT
ALT
ALT
ADDR
23
TEST
Installation and Quick-Start Guide
Remote control bottom
Rev B December 2017
page 10
Digital Projection E-Vision Laser 4K Series
REMOTE CONTROL
Infrared reception
The projector has infrared sensors at the front and back.
The angle of acceptance is 40°. Make sure that the remote control is within the angle of acceptance
when trying to control the projector.
40°
40°
Infrared reception
Notes
Installation and Quick-Start Guide
Rev B December 2017
page 11
Digital Projection E-Vision Laser 4K Series
POSITIONING THE SCREEN AND PROJECTOR
Positioning The Screen And Projector
1. Install the screen, ensuring that it is in the best position for viewing by your audience.
2. Mount the projector, ensuring that it is at a suitable distance from the screen for the image to ll the screen. Set the adjustable feet so that
the projector is level, and perpendicular to the screen.
The drawing below shows the positions of the feet for table mounting, and the xing holes for ceiling mounting.
1
Four adjustable feet
2
Six M4 holes for ceiling mount
The screws should not penetrate more than 15 mm into the body of the projector.
1
2
2
1
2
2
Notes
Always allow the projector
to cool for 5 minutes before
disconnecting the power or
moving the projector.
Ensure that there is at least 50
cm (19.7 in) of space between the
ventilation outlets and any wall,
and 30 cm (11.8 in) on all other
sides.
2
1
Installation and Quick-Start Guide
2
1
Rev B December 2017
page 12
Digital Projection E-Vision Laser 4K Series
POSITIONING THE SCREEN AND PROJECTOR
Roll and pitch
The projector can be operated in numerous positions.
In portrait mode, it is recommended to position the projector with inputs facing upward, as shown in the diagram.
30°
330°
1
360°
2
2
Notes
Roll
1
Recommended positions: inputs side up
2
Also possible
Installation and Quick-Start Guide
Pitch
Rev B December 2017
page 13
Digital Projection E-Vision Laser 4K Series
CHANGING THE LENS
Changing The Lens
Inserting a new lens
1. Remove the front and rear lens caps.
2. Position the lens so that the labels are at the top, and gently insert
it all the way into the lens mount.
3. Push the lens in rmly and turn it clockwise until it clicks into place.
Removing the lens
Notes
Before changing the lens,
always make sure the projector
is switched off and fully
disconnected from its power
supply.
When changing the lens, avoid
using excessive force as this may
damage the equipment.
The lens is shipped separately.
Take care to preserve the original
lens packaging and protective caps
for future use.
The projector will not power on
without the lens tted.
1. Push in the lens release lever, and turn the lens anti-clockwise.
2. Remove the lens.
Installation and Quick-Start Guide
Rev B December 2017
page 14
Digital Projection E-Vision Laser 4K Series
OPERATING THE PROJECTOR
Operating The Projector
Switching the projector on
1. Ensure a lens is tted. Connect the power cable between the mains supply and the projector. (See Connecting the power supply
above.) Switch on at the switch next to the power connector.
2. The POWER indicator lights red to signal that the projector is in STANDBY mode. Press one of the following buttons:
• On the remote control, the ON button
• On the projector control panel, the POWER button.
The fans begin working, then the POWER indicator begins ashing green. When the ashing stops, the POWER and LIGHT indicators
both light steady green. The projector is switched on.
Switching the projector off
1. Press OFF on the remote control or POWER on the control panel, then press again to conrm your choice.
The POWER indicator on the control panel will start ashing amber, the system will go out and the cooling fans will run for a short time
until the POWER indicator goes steady red to indicate that the projector has entered STANDBY mode.
2. If you need to switch the projector off completely, switch off at the mains power switch next to the power connector and then disconnect
the power cable from the projector.
Notes
See also Connecting The Power
Supply earlier in this guide.
The self-test is running when all the
LEDs on the control panel are lit.
Use only the power cable
provided.
Ensure that the power outlet
includes a ground connection as
this equipment MUST be earthed.
Handle the power cable carefully
and avoid sharp bends. Do not
use a damaged power cable.
Installation and Quick-Start Guide
Rev B December 2017
page 15
Digital Projection E-Vision Laser 4K Series
OPERATING THE PROJECTOR
Selecting an input signal
1. Connect one or more image sources to the projector.
2. Select the input you want to display:
• Press one of the input buttons on the remote control.
• Alternatively, open the On-screen display (OSD) by pressing MENU. Highlight Input from the main menu, press ENTER/OK and then
select an input signal using the UP and DOWN arrow buttons. Press ENTER/OK to conrm your choice.
Selecting a test pattern
To display a test pattern:
• Press TEST on the remote control.
Change the test pattern using the LEFT and RIGHT arrow buttons. Test patterns are displayed in the following order:
White, Black, Red, Green, Blue, Checkerboard, Crosshatch, V Burst, H Burst, Colour Bars, Screen layout, Off.
• Alternatively, open the OSD by pressing MENU. Highlight Test Patterns from the main menu, then select a test pattern using the LEFT
and RIGHT arrow buttons.
After the nal test pattern, the projector exits test pattern mode and returns to the main image. To view test patterns again, you need to press
TEST again. If you wish to exit the test patterns before you reach the nal one,
• press TEST or EXIT at any time.
Notes
For full details of how to use the
controls and the menu system, see
the Operating Guide.
Installation and Quick-Start Guide
Rev B December 2017
page 16
Digital Projection E-Vision Laser 4K Series
OPERATING THE PROJECTOR
Adjusting the lens
The lens can be adjusted using the Lens menu, or using the lens buttons on the remote control.
Lens menu
The Lens menu provides access to the Lens Control setting and the Lens Center command.
Lens Control allows Zoom, Focus and Shift adjustment using the arrow buttons. The setting operates in Zoom/Focus Adjustment and
Shift Adjustment mode.
Press ENTER/SELECT to switch between the two modes.
Remote control
Use the remote control to adjust zoom, focus and shift directly, without opening a menu:
• OK enters lens control, then switches between Zoom/Focus Adjustment and Shift Adjustment.
• EXIT exits lens control and opens the Lens menu.
• MENU exits lens control and returns to the main image.
• The arrow buttons adjust zoom, focus and shift as indicated on the screen.
Adjusting the image
Orientation
• This can be set from the Setup menu.
Highlight Orientation and choose from Front Tabletop, Front Ceiling, Rear Tabletop, Rear Ceiling and Auto-front.
Notes
For full details of how to adjust
the lens using the remote control,
see Remote Control earlier in this
guide.
Geometry
• Settings such as Keystone, Rotation, Pincushion / Barrel and Arc can be set from the Geometry menu.
Picture
• Settings such as Gamma, Brightness, Contrast, Saturation, Hue and Sharpness can be set from the Image menu.
Installation and Quick-Start Guide
Neither of the settings under Picture
are available with the HDMI 3 and 4
inputs.
Rev B December 2017
page 17
Digital Projection E-Vision Laser 4K Series
This page is intentionally left blank.
Installation and Quick-Start Guide
E-Vision Laser 4K Series
High Brightness Digital Video Projector
4
CONNECTION GUIDE
Rev B December 2017
Digital Projection E-Vision Laser 4K Series
CONTENTS
CONTENTS
SIGNAL INPUTS .......................................................................................21
DIGITAL INPUTS AND OUTPUTS ................................................. 21
EDID ON THE DISPLAYPORT, HDMI AND HDBASET INPUTS....... 22
USING DISPLAYPORT/HDMI/HDBASET SWITCHERS WITH THE
PROJECTOR ................................................................................ 22
3D CONNECTIONS ...................................................................... 23
Frame sequential 1080p 3D up to 120Hz and WUXGA 3D at 100Hz 23
Dual Pipe 1080p, WUXGA and WQXGA+ 3D sources at up to 100 and
120 Hz ................................................................................................. 23
3D SYNC ...................................................................................... 24
3D Sync In........................................................................................... 24
3D Sync Out ........................................................................................ 24
3D Sync IR .......................................................................................... 24
CONTROL CONNECTIONS .................................................................25
LAN CONNECTION EXAMPLES ................................................... 26
RS232 CONNECTION EXAMPLE ...................................................... 27
Connection Guide
Rev B December 2017
Digital Projection E-Vision Laser 4K Series
SIGNAL INPUTS
Signal Inputs
Digital inputs and outputs
HDBaseT
1
Receives digital signal from HDBaseT-compliant devices.
3G-SDI in
2
3G-SDI out
3
Connect a 3G-SDI cable to distribute the 3G-SDI signal to another projector.
HDMI 1 / HDMI 2 / HDMI 3 / HDMI 4
4
HDMI 1 and 2 are HDMI 2.0 inputs supporting HDCP 2.2.
HDMI 3 and 4 are HDMI 1.4b inputs supporting Frame Sequential and Dual Pipe 3D with HDCP 1.4.
Connect an HDMI cable to the connector.
DisplayPort
5
DisplayPort 1.2 input. Connect a DisplayPort cable to the connector.
Supports sources up to 4K-UHD resolution at 60 Hz and WQXGA at 120Hz.
Notes
For simultaneous HDBaseT and
LAN connectivity, a third-party
distribution product can be utilised
to combine HDBaseT video stream
with LAN connection for delivery to
the projector.
Connection Guide
HDBaseT/LAN Ethernet
SDI IN SDI OUT
1
2 3
(1) (2) RS232
TRIGGER
3D SYNC IR
HDMI1HDMI
2
HDMI3HDMI
4
4 5
WIRED REMOTE
DisplayPort
SYNC IN SYNC OUT
Rev B December 2017
page 21
Digital Projection E-Vision Laser 4K Series
SIGNAL INPUTS
EDID on the DisplayPort, HDMI and HDBaseT inputs
If you are using a computer graphics card or another source that obeys the EDID protocol, the source will automatically congure itself to suit
the capability of the projector.
Otherwise refer to the documentation supplied with the source to manually set the resolution to the DMD™ resolution of the projector or the
nearest suitable setting. Switch off the source, connect to the projector, then switch the source back on again.
Using DisplayPort/HDMI/HDBaseT switchers with the projector
When using a DisplayPort/HDMI/HDBaseT source switcher with the projector, it is important to set the switcher so that it passes the projector
EDID through to the source devices. If this is not done, the projector may not be able to lock to the source or display the source correctly as
its video output timings may not be compatible with those of the projector. Sometimes this is called transparent, pass-through or clone mode.
See your switcher’s manual for information on how to set this mode.
1
Sources
2
Switcher
3
Projector
1 32
EDID
EDID
EDID
EDID
Notes
Connection Guide
The EDIDs in the switcher should be the same as the one in the projector.
Rev B December 2017
page 22
Loading...