Digital Projection E-Vision Laser 11000 User Manual

Download

E-Vision Laser 11000 4K-UHD Series

High Brightness Digital Video Projector

INSTALLATION & QUICK START GUIDE

CONNECTION GUIDE

OPERATING GUIDE

REFERENCE GUIDE

Rev A June 2019

120-091A

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series About this document

About this document

Follow the instructions in this manual carefully to ensure safe and long-lasting use of the projector.

Symbols used in this document

Many pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:

WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless the instructions are closely followed.

ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely followed.

LASER WARNING: this symbol indicates that there is a potential hazard of eye exposure to laser radiation unless the instructions are closely followed.

NOTE: this symbol indicates that there is some important information that you should read.

Product revision

Because we at Digital Projection continually strive to improve our products, we may change specifications and designs, and add new features without prior notice.

Updates may be available online. Please visit the Digital Projection website for all latest documents.

Legal notice

Trademarks and trade names mentioned in this document remain the property of their respective owners. Digital Projection disclaims any proprietary interest in trademarks and trade names other than its own.

Notes

Rev A June 2019

page2

Introduction

Laser information Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007

LASER RADIATION

AVOID DIRECT EYE EXPOSURE

CLASS 3R LASER PRODUCT

Emitted wavelength : 450-460 nm

Max. Pulse energy: 0.34 mJ, Pulse duration: 0.65 ms

激光辐射避免眼睛受到直接照射 3R类激光产品

波长

: 450-460 nm

最大脉冲能量: 0.34 mJ, 脉冲时间: 0.65 ms

雷射輻射避免眼睛受到直接照射 3R類激光產品

波長: 450-460 nm

最大脈衝能量: 0.34 mJ, 脈衝時間: 0.65 ms

RAYONNEMENT LASER

EXPOSITION DIRECTE DANGEREUSE POUR LES YEUX

APPAREIL À LASER DE CLASSE 3R

longueur d'onde : 450-460nm

maximum énergie de impulsion : 0.34 mJ,

durée de impulsion : 0.65 ms

GB 7247.1-2012 / IEC/EN 60825-1:2007

CLASS 1 LASER PRODUCT

IEC/EN 60825-1:2014

PRODUIT LASER DE CLASSE 1

IEC/EN 60825-1:2014

3264655300

RG2

CAUTION: Do not look into the lens

Laser information

Caution - use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

Optical radiation

Notes

Caution - possibly hazardous optical radiation emitted from this product. Do not stare at operating light source. May be harmful to eyes. This projector is tested according to IEC/EN62471-5:2015 (Photobiological safety of lamps and lamp systems – Part 5: Image projectors standard) and is Risk Group 2 (low risk).

Introduction

Rev A June 2019

page3

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Introduction

Introduction

Congratulations on your purchase of this Digital Projection product. Your projector has the following key features:

l 4K-UHD projector.

l Displays 4K-UHD with smooth picture processing.

l Support for Frame Sequential and Dual Pipe 3D formats.

l HDBaseT® for transmission of uncompressed High Definition Video up to 100 m from the source.

l 3G-SDI with loop-through.

l Edge Blend with black level correction.

l Blanking control for custom input window sizing.

l Cornerstone, Vertical & Horizontal Keystone, Pincushion & Barrel, and Image Rotation.

l Control via LAN and RS232.

l Motorised lens mount.

l Separate control of screen and source aspect ratio.

A serial number is located on the side of the projector. Record it here:

Notes

Rev A June 2019

page4

Introduction

Contents Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

About this document 2

Symbols used in this document 2

Product revision 2

Legal notice 2

Laser information 3

Optical radiation 3

Introduction 4

Contents 5

What's in the box? 10

Connecting the power supply 11

Voltage selection 11

Projector overview 12

Control panel 13

Projector indicators 14

Remote control 15

Infrared reception 18

Positioning the screen and projector 19

Roll and pitch 20

Changing the lens 21

Inserting a new lens 21

Removing the lens 21

Operating the projector 22

Switching the projector on 22

Switching the projector off 22

Selecting an input signal 22

Selecting a test pattern 22

Notes

Adjusting the lens 23

Lens menu 23

Remote control 23

Adjusting the image 23

Orientation 23

Geometry 23

Picture 23

Signal inputs 26

Digital inputs and outputs 26

EDID on the DisplayPort, HDMI, and HDbaseT inputs 27

Using DisplayPort/ HDMI/ HDBaseT switchers with the projector 27

3D connections 28

Frame sequential 1080p 3D up to 120Hz and WUXGA 3D at 100Hz 28

Dual Pipe 1080p, WUXGA and WQXGA+ 3D sources at up to 100 and 120Hz 28

3D Sync 29

Control connections 30

LAN connection examples 31

RS232 connection example 32

Using the menus 34

Opening the Menu 34

Opening a submenu 34

Exiting menus and closing the OSD 35

Inside a menu 35

Accessing sub menus 36

Executing commands 36

Introduction

Rev A June 2019

page5

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Contents

Editing projector settings 37

Using a slider to set a value 37

Editing numeric values 38

Using the projector 39

Main menu 39

Lens menu 40

Lens control 40

Lens memory 41

Image menu 42

Color menu 44

Color space 44

Color mode 45

ColorMax 45

Manual color matching 46

Color matching parameters explained 47

Color temperature 48

Gains and lifts 48

Top right corner example 58

Rotation 59

Rotation example 60

Pincushion / barrel 61

Pincushion/ Barrel example 61

Arc 62

Custom warp 63

Edge blend menu 64

Blend width 65

Black level uplift 66

3D menu 67

3D types 68

Some 3D settings explained 69

Dark time 69

Eye swap 69

Sync offset 70

Laser menu 71

Notes

Geometry menu 49

Aspect ratio 49

Theaterscope setting 50

Digital zoom 51

Overscan 52

Blanking 53

Keystone 54

Keystone example 55

Keystone settings 56

4 corners 57

Rev A June 2019

page6

Setup menu 72

ColorMax 74

Measured data/ target data 74

Power on / off 75

Clock adjust 76

OSDsettings 76

Memory 77

Network menu 78

PIP menu 79

Information menu 80

Introduction

Contents Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Signal format 80

System status 81

Thermal status 81

Factory reset 82

Served web pages 83

Choosing a lens 96

Basic calculation 97

Basic calculation example 98

Full lens calculation 99

Introducing TRC 99

Calculating TRC 100

TRC table 100

Calculating the throw ratio with TRC 100

Full lens calculation example 101

Screen requirements 102

Fitting the image to the display 102

4K-UHD images displayed full width 102

Appendix A: supported signal input modes 109

2D formats 109

3D formats 112

SDI formats 113

Appendix B: wiring details 114

Signal inputs and outputs 114

HDMI 1 and 2 114

DisplayPort 115

3G-SDI in, 3G-SDI out 116

HDBaseT input 116

Control connections 117

LAN 117

RS232 117

IR input 117

Appendix C: glossary of terms 118

Notes

4K-UHD images displayed with a height of 2160 pixels 102

4K-UHD images displayed full height 103

Diagonal screen sizes 103

Positioning the image 104

Aspect ratios explained 106

Aspect ratios examples 106

Source: 4:3 106

Source: 16:9 107

Source: 16:10 (native) 107

Aspect ratio example: TheatreScope 108

Introduction

Rev A June 2019

page7

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

This page is intentionally left blank

Rev A June 2019

E-Vision Laser11000 4K-UHD Series

High Brightness Digital Video Projector

INSTALLATION & QUICK START GUIDE

Rev A June 2019

120-091A

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series What's in the box?

PicMute

OPEN

EXIT INFO

HDMI1

OFF ON

ALT

LENS

FOCUS ZOOM

OUT

SHIFT

21 3

HDMI2 DVI

DisplayPort1

HD-T 3GSDI

VGA COMP1 COMP2

HDMI3

TEST

HDMI4

DisplayPort2

R G B ALL

3D EYE PIP SWAP

4 5 6

7 8 9 0

ALT

ADDR

OSD

OFF

DEFAULT

FREEZE

RE-SYNC

A B C D

USERPRESET

What's in the box?

Projector

Remote Control

Notes

Make sure your box contains everything listed. If any pieces are missing, contact your dealer.

Only one remote is supplied with the projector.

Save and store the original box and packing materials, in case you ever need to ship your projector.

Batteries

The projector is shipped without a lens.

Only the appropriate cable for destination territory is supplied with the projector

Security Screw

Rev A June 2019

page10

Important Information Book HDMI Cable

Power Cable, UK Power Cable, Europe Power Cable, North America Power Cable, China

Installation & Quick Start Guide

Connectingthe power supply Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Connecting the power supply

Adjust the VOLTAGE SELECT switch to the required voltage

Firmly push the mains connector into the socket

Voltage selection

The VOLTAGE SELECT switch must be set to match the power supply you are using:

Voltage of power supply used Position of VOLTAGE SELECT switch

Notes

Use only the power cable provided.

Ensure that the power outlet includes a ground connection as this equipment MUST be earthed.

Handle the power cable carefully and avoid sharp bends. Do not use a damaged power cable.

AC100-130V outlet

AC200-240V (single phase) outlet

Installation & Quick Start Guide

Rev A June 2019

page11

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Projector overview

567

91011

124

Projector overview

1. Air inlet

2. Front infrared window

3. Lens mount

4. Air inlet

5. Rear infrared window

6. Air outlet

7. Connections panel

8. Control panel

9. Adjustable feet

10. Voltage selector

11. Mains socket and switch

12. Air inlets

Front View

Notes

Rear View

Rev A June 2019

page12

Bottom View

Installation & Quick Start Guide

Controlpanel Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

POWER

INPUT

AUTO SYNC

ASPECT

CENTER

LENS

PIC MUTE

12345

7 8 9 10 11 12

Control panel

1. POWER Switches the projector on and off (STANDBY).

2. INPUT Switches to the next input source.

3. AUTO SYNC Re-synchronises with the current input signal.

4. ASPECT Changes the aspect ratio.

5. CENTER LENS Centers the lens.

6. PIC MUTE Shows and hides the projected image. When muted, the light source is completely switched off and the screen is black.

7. MENU Displays and exits the OSD.

8. Arrow buttons & ENTER Navigation buttons used to highlight menu entries in the OSD. Press ENTER to open or execute the highlighted menu entry.

9. EXIT Exits the current OSD page and enters the level above.

10. LENS SHIFT Arrow buttons move the lens in the specified direction.

11. FOCUS Plus and minus buttons move the focus in and out.

12. ZOOM Plus and minus buttons zoom in and out.

Notes

AUTO SYNC and ASPECT do not work when the projector uses HDMI 3 or 4.

Control Panel

Installation & Quick Start Guide

Rev A June 2019

page13

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Control panel

POWERSTAT USLIGHTTEMP.

Projector indicators

TEMP. Off = no problem

Flashing red = temperature error

LIGHT Off = light is switched off

Flashing green = light is preparing to switch on

Flashing red (cycles of six flashes) = light module failure

On, red = light module has reached end of life

On, green = light is switched on

STATUS Off = no problem

Flashing red (continuously) = cover error

Flashing red (cycles of four flashes) = fan error

On, red = system error

POWER Off = the projector is switched off

Flashing green = the projector is warming up

Flashing amber = the projector is cooling down

On, red = STANDBY mode

On, green = the projector is switched on

Notes

Indicators

Rev A June 2019

page14

Installation & Quick Start Guide

Remotecontrol Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Pic Mute

OPEN

EXIT INFO

HDMI1

OFF ON

ALT

LENS

FOCUS ZOOM

OUT

SHIFT

21 3

HDMI2 DVI

DisplayPort1

HD-T 3GSDI

VGA COMP1 COMP2

HDMI3

TEST

HDMI4

DisplayPort2

R G B ALL

3D EYE PIP SWAP

4 5 6

7 8 9 0

ALT

ADDR

OSD

OFF

DEFAULT

FREEZE

RE-SYNC

A B C D

USER PRESET

543

217

Remote control

1. Power ON / OFF Turns power on and off.

2. Pic Mute OPEN / CLOSE Shows and hides the projected image. When OFF, the light source is completely switched off and the screen is black.

3. OSD ON / OFF Enable and disable screen timeout messages and control whether to show the OSD during projection.

4. MENU Access the OSD. If the OSD is open, press this button to go back to the previous menu.

5. Navigation (arrows and OK) Navigate through the menus with the arrows, confirm your choice with OK. In lens adjustment modes, the arrows are used to move, zoom or focus the lens. See 11 below. In lens adjustment modes, or when the OSD is not showing, the OK button switches between modes: Shift Adjustment and Zoom / Focus Adjustment.

6. EXIT Go up one level in the OSD. When the top level is reached, press to close the OSD.

7. FREEZE Freeze the current frame.

8. DEFAULT When editing a parameter, press this button to restore the default value.

9. INFO Access information about the projector.

10. RE-SYNC Re-synchronise with the current input signal

Notes

FREEZE and RE-SYNC are not available when the projector uses input HDMI 3 or 4.

Installation & Quick Start Guide

Remote Control

Rev A June 2019

page15

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Remote control

Pic Mute

OPEN

EXIT INFO

HDMI1

OFF ON

ALT

LENS

FOCUS ZOOM

OUT

SHIFT

21 3

HDMI2 DVI

DisplayPort1

HD-T 3GSDI

VGA COMP1 COMP2

HDMI3

TEST

HDMI4

DisplayPort2

R G B ALL

3D EYE PIP SWAP

4 5 6

7 8 9 0

ALT

ADDR

OSD

OFF

DEFAULT

FREEZE

RE-SYNC

A B C D

USER PRESET

11. LENS adjustment

l FOCUS IN / OUT: adjust focus.

l SHIFT: press and hold this button, then use the Navigation arrow buttons to move the

lens.

l ZOOM IN / OUT: adjust zoom.

12. USER PRESET A, B, C, D Load user presets.

13. ALT Press and hold this button to access alternative functions for all buttons with a green label.

14. DVI / DisplayPort2 / numeric input 3 There is no DVI input on this projector. Use with ALT to select the DisplayPort 2 input.

15. HDMI 2 / HDMI 4 / numeric input 2

16. HDMI 1 / HDMI 3 / numeric input 1

Select the HDMI 2 input. Use with ALT to select the HDMI 4 input.There is no HDMI 4 input on this projector

Select the HDMI 1 input. Use with ALT to select the HDMI 3 input.There is no HDMI input on this projector

Notes

This projector does not use the following options on the remote: DVI, VGA, COMP 1 and COMP 2.

3D is only available on the HDMI 3 and 4 inputs.

Rev A June 2019

page16

Remote Control

Installation & Quick Start Guide

Remotecontrol Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Pic Mute

OPEN

EXIT INFO

HDMI1

OFF ON

ALT

LENS

FOCUS ZOOM

OUT

SHIFT

21 3

HDMI2 DVI

DisplayPort1

HD-T 3GSDI

VGA COMP1 COMP2

HDMI3

TEST

HDMI4

DisplayPort2

R G B ALL

3D EYE PIP SWAP

4 5 6

7 8 9 0

ALT

ADDR

OSD

OFF

DEFAULT

FREEZE

RE-SYNC

A B C D

USER PRESET

222418

17. DISPLAYPORT 1 / R / numeric input 4 Select DisplayPort 1 input.

18. HD-T / G / numeric input 5 Select the HDBaseT input.

19. VGA / 3D / numeric input 7 There is no VGA input on this projector. Use with ALT to toggle the 3D Format setting between Off and Auto.

20. COMP1 / EYE / numeric input 8 There is no Component 1 input on this projector. Use with ALT to switch between left and right eye 3D dominance.

21. ADDR / ALL (with red indicator at the top) Assign and unassign an IR remote address.

l To assign an IR remote address:

1. Press and hold this button until the red indicator starts flashing.

2. Release this button and while the red indicator is still flashing, enter a two-

l To unassign an address and return to the default address 00:

digit address using the numeric input buttons. The indicator will flash three times quickly to confirm the change.

1. Press and hold ALT and this button simultaneously until the red indicator flashes to confirm the change.

22. 3GSDI / B / numeric input 6 Select the 3G-SDI input.

23. TEST / SWAP / numeric input 0 Show a test pattern. Press again to show the next test pattern: White, Black, Red, Green, Blue, Checkerboard, Crosshatch, V Burst, H Burst, Color Bar, Screen Layout, Off.. When PIP mode is on, use this button with ALT to swap the main and sub images.

24. COMP2 / PIP / numeric input 9 There is no Component 2 input on this projector. Use with ALT to switch on Picture In Picture (PIP) mode.

Notes

This projector does not use the following options on the remote: DVI, VGA, COMP 1 and COMP 2.

3D is only available on the HDMI 3 and 4 inputs.

PIP is not available when the projector uses input HDMI 3 or 4.

Installation & Quick Start Guide

Remote Control

Rev A June 2019

page17

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Remote control

40˚

Infrared reception

The projector has infrared sensors at the front and back.

The angle of acceptance is 40°. Make sure that the remote control is within the angle of acceptance when trying to control the projector.

Notes

Rev A June 2019

page18

Installation & Quick Start Guide

Positioningthe screen and projector Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

111

Positioning the screen and projector

1. Install the screen, ensuring that it is in the best position for viewing by your audience.

2. Mount the projector, ensuring that it is at a suitable distance from the screen for the image to fill the screen. Set the adjustable feet so that the projector is level, and perpendicular to the screen.

The drawing shows the positions of the feet for table mounting, and the fixing holes for ceiling mounting.

1. Four adjustable feet

2. Six M4 holes for ceiling mount The screws should not penetrate more than 15 mm into the body of the projector.

Notes

Always allow the projector to cool for 5 minutes before disconnecting the power or moving the projector.

Ensure that there is at least 50 cm (19.7 in) of space between the ventilation outlets and any wall, and 30 cm (11.8 in) on all other sides.

Do not use the threaded holes for the adjustable feet to hang or mount the projector.

Installation & Quick Start Guide

Rev A June 2019

page19

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Positioningthe screen and projector

360˚

30˚

330˚

Roll and pitch

The projector can be operated in numerous positions.

In portrait mode, it is recommended to position the projector with inputs facing upward, as shown in the diagram.

1. Recommended positions: inputs side up

2. Also possible.

Notes

Rev A June 2019

page20

Pitch

Roll

Installation & Quick Start Guide

Changingthe lens Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Changing the lens

Inserting a new lens

1. Remove the lens aperture cap from the projector.

2. Remove the front and rear lens caps from the lens.

3. Position the lens so that the labels are at the top, and gently insert it all the way into the lens mount.

4. Push the lens in firmly and turn it clockwise until it clicks into place.

Notes

Before changing the lens, always make sure the projector is switched off and fully disconnected from its power supply.

When changing the lens, avoid using excessive force as this may damage the equipment.

Avoid touching the surface of the lens as this may result in image impairment.

The lens is shipped separately.

Take care to preserve the original lens packaging and protective caps for future use.

Removing the lens

1. Push the lens release button all the way in

2. Turn the lens anti-clockwise until it disengages

3. Slowly remove the lens.

Installation & Quick Start Guide

The projector will not power on without the lens fitted.

Rev A June 2019

page21

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Operating the projector

Operating the projector

Switching the projector on

1. Ensure a lens is fitted. Connect the power cable between the mains supply and the projector. (See Connecting the power supply above.) Switch on at the switch next to the power connector.

2. The POWER indicator lights red to signal that the projector is in STANDBY mode. Press one of the following buttons:

l On the remote control, the ON button

l On the projector control panel, the POWER button.

The fans begin working, then the POWER indicator begins flashing green. When the flashing stops, the POWER and LIGHT indicators both light steady green. The projector is switched on.

Switching the projector off

1. Press OFF on the remote control or POWER on the control panel, then press again to confirm your choice. The POWER indicator on the control panel will start flashing amber, the system will go out and the cooling fans will run for a short time until the POWER indicator goes steady red to indicate that the projector has entered STANDBY mode.

2. If you need to switch the projector off completely, switch off at the mains power switch next to the power connector and then disconnect the power cable from the projector.

Selecting an input signal

1. Connect one or more image sources to the projector.

2. Select the input you want to display:

l Press one of the input buttons on the remote control.

l Alternatively, open the On-screen display (OSD) by pressing MENU. Highlight Input from the main menu, press ENTER/OK and then select an input

signal using the UP and DOWN arrow buttons. Press ENTER/OK to confirm your choice.

Notes

See Connecting the power supply on page11.

The self-test is running when all the LEDs on the control panel are lit.

Use only the power cable provided.

Ensure that the power outlet includes a ground connection as this equipment MUST be earthed.

Handle the power cable carefully and avoid sharp bends. Do not use a damaged power cable.

See Using the menus on page34 for full details of how to use the controls and the menu system.

Selecting a test pattern

To display a test pattern:

l Press TEST on the remote control.

Change the test pattern using the LEFT and RIGHT arrow buttons. The following test patterns are available: White, Black, Red, Green, Blue, Checkerboard, Crosshatch, V Burst, H Burst, Color Bar, Screen Layout, Off.

l Alternatively, open the OSD by pressing MENU. Highlight Test Patterns from the main menu, then select a test pattern using the LEFT and RIGHT arrow

buttons.

After the final test pattern, the projector exits test pattern mode and returns to the main image. To view test patterns again, you need to press TEST again. If you wish to exit the test patterns before you reach the final one, press TEST or EXIT at any time.

Rev A June 2019

page22

Installation & Quick Start Guide

Operating the projector Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Adjusting the lens

The lens can be adjusted using the Lens menu, or using the lens buttons on the remote control.

Lens menu

The Lens menu provides access to the Lens Control setting and the Lens Center command.

Lens Control allows Zoom, Focus and Shift adjustments using the arrow buttons. The setting operates in Zoom/Focus Adjustment and Shift Adjustment mode.

Press ENTER/SELECT to switch between the two modes.

Remote control

Use the remote control to adjust zoom, focus and shift directly, without opening a menu:

l OK enters lens control, then switches between Zoom/Focus Adjustment and Shift Adjustment.

l EXIT exits lens control and opens the Lens menu.

l MENU exits lens control and returns to the main image.

l The arrow buttons adjust zoom, focus and shift as indicated on the screen.

Adjusting the image

Orientation

This can be set from the Setup menu.

Highlight Orientation and choose from Front Tabletop, Front Ceiling, Rear Tabletop, Rear Ceiling and Auto-front.

Geometry

Notes

See Remote control on page15 for full details of how to adjust the lens using the remote control.

Settings such as Keystone, Rotation, Pincushion / Barrel and Arc can be set from the Geometry menu.

Picture

Settings such as Gamma, Brightness, Contrast, Saturation, Hue and Sharpness can be set from the Image menu.

Installation & Quick Start Guide

Neither of the settings under Picture are available with the HDMI 3 and 4 inputs.

Rev A June 2019

page23

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

This page is intentionally left blank

Rev A June 2019

E-Vision Laser11000 4K-UHD Series

High Brightness Digital Video Projector

CONNECTION GUIDE

Rev A June 2019

120-091A

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Signal inputs

HDBaseT/LAN Ethernet

SDI IN SDI OUT

3D SYNC IR

TRIGGER

(1) (2) RS232

WIRED REMOTE

HDMI1HDMI

HDMI3HDMI

SYNC IN SYNC OUT

DisplayPort

564

Signal inputs

Digital inputs and outputs

1. HDBaseT Receives digital signal from HDBaseT-compliant devices. Connect an HDBaseT cable.

2. 3G-SDI in

3. 3G-SDI out Connect a 3G-SDI cable to distribute the 3G-SDI signal to another projector.

4. HDMI 1 / HDMI 2 HDMI 2.0 inputs supporting HDCP 2.2. Connect an HDMI cable to the connector.

5. HDMI 3 / HDMI 4

HDMI 1.4b inputs supporting Frame Sequential and Dual Pipe 3D with HDCP 1.4. Also supports the domestic Blu-Ray formats. See supported signal input modes on page109. Connect an HDMI cable to the connector.

6. DisplayPort DisplayPort 1.2 input. Connect a DisplayPort cable to the connector. Supports sources up to 4K-UHD resolution at 60 Hz and WQXGA at 120Hz.

Notes

For simultaneous HDBaseT and LAN connectivity, a third-party distribution product can be utilised to combine HDBaseT video stream with LAN connection for delivery to the projector.

Rev A June 2019

page26

Connection Guide

Signal inputs Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

EDID

123

EDID on the DisplayPort, HDMI, and HDbaseT inputs

If you are using a computer graphics card or another source that obeys the EDID protocol, the source will automatically configure itself to suit the capability of the projector.

Otherwise refer to the documentation supplied with the source to manually set the resolution to the DMD™ resolution of the projector or the nearest suitable setting. Switch off the source, connect to the projector, then switch the source back on again.

Using DisplayPort/ HDMI/ HDBaseT switchers with the projector

When using a DisplayPort/HDMI/HDBaseT source switcher with the projector, it is important to set the switcher so that it passes the projector EDID through to the source devices.

If this is not done, the projector may not be able to lock to the source or display the source correctly as its video output timings may not be compatible with those of the projector. Sometimes this is called transparent, pass-through or clone mode. See your switcher’s manual for information on how to set this mode.

1. Sources

2. Switcher

3. Projector

Notes

Connection Guide

The EDIDs in the switcher should be the same as the one in the projector.

Rev A June 2019

page27

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series 3D connections

HDBaseT/LAN Ethernet

SDI IN SDI OUT

3D SYNC IR

TRIGGER

(1) (2) RS232

WIRED REMOTE

HDMI1HDMI

HDMI3HDMI

SYNC IN SYNC OUT

DisplayPort

3D connections

1. 3D Sync IR Sync output signal. This is affected by settings in the 3D menu such as Dark Time and 3D Sync Offset. Connect this to an IR emitter or ZScreen.

2. HDMI 3 / HDMI 4 HDMI 1.4b inputs supporting Frame Sequential and Dual Pipe 3D with HDCP 1.4. Also supports the domestic Blu-Ray formats. See supported signal input modes on page109. Connect an HDMI cable to the connector.

3. Sync In / Sync Out Sync In is the 3D sync input signal. Connect the 3D sync from your graphics card or server. Sync Out is the 3D sync output signal. Enables 3D from multiple projectors.

Frame sequential 1080p 3D up to 120Hz and WUXGA 3D at 100Hz

1. Connect to HDMI 3 or 4.

2. Set 3D Format in the 3D menu to Frame Sequential.

Dual Pipe 1080p, WUXGA and WQXGA+ 3D sources at up to 100 and 120Hz

1. Connect the left eye output to the HDMI 3 socket and the right eye output to the HDMI 4 socket.

2. Set 3D Format in the 3D menu to Dual-Pipe.

Notes

See 3D formats on page112 for a complete list of supported formats and frame rates.

Rev A June 2019

page28

Connection Guide

3D connections Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

3D Sync

1. 3D Input

2. 3D Sync In

3. 3D Sync IR

4. IR emitter or Zscreen

Notes

Connection Guide

Rev A June 2019

page29

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Controlconnections

HDBaseT/LAN Ethernet

SDI IN SDI OUT

3D SYNC IR

TRIGGER

(1) (2) RS232

WIRED REMOTE

HDMI1HDMI

HDMI3HDMI

SYNC IN SYNC OUT

DisplayPort

123

Control connections

1. HDBaseT/LAN The projector’s features can be controlled via a LAN connection, using Digital Projection’s Projector Controller application or a terminal-emulation program.

2. Ethernet This dedicated LAN connection can be used if HDBaseT/LAN is already being used for HDBaseT signal input.

3. Trigger 1 & Trigger 2

The Trigger outputs are defined in the Setup menu. Each ouput can be triggered by one of the following conditions:

l Screen trigger. A trigger output can be used to control an electrically operated screen. The screen will be automatically deployed when the projector

starts up and retracted when the projector shuts down.

l Aspect ratio trigger. A trigger output can be used to control screen shuttering for different aspect ratios.

l RS232 trigger. A trigger output can be used to control the screen or screen shuttering on receipt of an RS232 command.

4. RS232 All of the projector’s features can be controlled via a serial connection, using commands described in the Protocol Guide.Use a straight-through cable to connect directly to a computer.

5. Wired Remote The remote control can be connected using a standard 3.5 mm mini jack cable (tip-ring-sleeve, or TRS).

Notes

For a list of all commands used to control the projector via LAN, see the Protocol Guide (available separately).

Only one remote connection (RS232 or LAN) should be used at any one time.

With a LAN connection the projector can serve a web page offering status and projector controls.

Trigger 1 and Trigger 2 are not available with HDMI 3 and 4 inputs.

Projector Controller is available for download, free of charge, from the Digital Projection website.

Rev A June 2019

page30

Connection Guide

Controlconnections Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Un-crossed

LAN cable

Un-crossed LAN cables

LAN connection examples

The projector’s features can be controlled via a LAN connection, using Digital Projection’s Projector Controller application or a terminal emulation program.

Notes

With a LAN connection the projector can serve a web page offering basic projector controls.

Projector Controller is available for download, free of charge, from the Digital Projection website.

For simultaneous HDBaseT and LAN connectivity, a third-party distribution product can be utilised to combine HDBaseT video stream with LAN connection for delivery to the projector.

Connection Guide

Rev A June 2019

page31

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Controlconnections

Straight through cable

RS232 connection example

All of the projector’s features can be controlled via a serial connection, using commands described in the Protocol Guide.

Computer to Projector

Notes

The Protocol Guide is available separately

Rev A June 2019

page32

Connection Guide

E-Vision Laser11000 4K-UHD Series

High Brightness Digital Video Projector

OPERATING GUIDE

Rev A June 2019

120-091A

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Using the menus

Pic Mute

OPEN

EXIT INFO

HDMI1

OFF ON

ALT

LENS

FOCUS ZOOM

OUT

SHIFT

21 3

HDMI2 DVI

DisplayPort1

HD-T 3GSDI

VGA COMP1 COMP2

HDMI3

TEST

HDMI4

DisplayPort2

R G B ALL

3D EYE PIP SWAP

4 5 6

7 8 9 0

ALT

ADDR

OSD

OFF

DEFAULT

FREEZE

RE-SYNC

A B C D

USER PRESET

POWER

INPUT

AUTO

SYNC

ASPECT

CENTER

LENS

PIC MUTE

Using the menus

Opening the Menu

Access the various menus using either the projector control panel or the remote control. On either device:

1. Press the MENU button. The on-screen display (OSD) opens showing the list of available menus

Notes

Projector control panel

Opening a submenu

Move up and down the list using the UP and DOWN arrow buttons.

To open a submenu:

1. Press ENTER on the control panel or OK on the remote control.

This guide refers to the above two buttons as ENTER/OK.

Rev A June 2019

page34

Remote control

Operating Guide

Using the menus Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Exiting menus and closing the OSD

To go back to the previous page:

1. Press EXIT.

To close the OSD:

1. Press MENU.

Or:

1. Go back to the top level menu

2. Press EXIT.

Input HDMI 1

Test Pattern

Lens ►

Image ►

Color ►

Geometry ►

Edge Blend ►

3D ►

Laser ►

Setup ►

Network ►

On Screen Display (OSD): Top Level Menu

Main Menu

▼

Inside a menu

When you open a menu, the page consists of the following elements:

l Title bar at the top shows which menu you have accessed.

l Highlighted item

l Available and unavailable items Unavailable items appear a pale gray color. Whether an item is

available may depend on other settings.

l The text or symbol to the right of an item shows whether the item:

l has a value that can be changed (the current value is shown)

l opens a sub-menu (an arrow button is displayed)

l executes a command (the space to the right of the item is blank).

Main Menu

▲

PIP ►

Information ►

OSD: Top Level Menu Continued

Menu Name

Highlighted Item Value

Menu Item Value

Unavailable Item Value

Slider Value

Sub-menu ►

Command

Notes

The highlighted item has green background.

Operating Guide

Inside a menu

Rev A June 2019

page35

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Using the menus

Accessing sub menus

Use the UP and DOWN arrow buttons to highlight the sub-menu, then press ENTER/OK.

Executing commands

If the item contains a command, highlighting it reveals an OK button.

Press ENTER/OK to execute the highlighted command.

You may be asked for confirmation. Use the ENTER/OK to confirm, or EXIT to cancel.

Menu Item Value

Highlighted Command

Menu Name

Highlighted Command

Notes

Command Name

Warning All [Menu] values will be lost.

Press OK to confirm

Press Exit to cancel

Confirmation Dialog

Rev A June 2019

page36

Operating Guide

Using the menus Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Editing projector settings

If the highlighted menu item contains a list of values to choose from, you can change the value by doing the following:

1. Highlight the menu item and press ENTER/OK.

2. In the list of values that opens, use the UP and DOWN arrow buttons to highlight a value, then press

ENTER/OK again to select the highlighted value.

Using a slider to set a value

Some parameters open a slider. To set such a parameter:

1. Press the LEFT or RIGHT arrow button, or ENTER/OK. The arrow buttons will open the slider and adjust the value at the same time. ENTER/OK will open the slider without altering the initial value.

2. Use the LEFT and RIGHT arrow buttons to move the slider.

3. When ready, press EXIT to exit the slider and return to the menu, or press MENU to exit the slider without showing the menu again.

Highlighted Item Current Value

Menu Item

Parameter Value

Menu Name

Highlighted Value

Value

List of Values

Slider

Notes

Some menu items may be unavailable due to settings in other menus. Unavailable menu items appear gray

Operating Guide

Rev A June 2019

page37

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Using the menus

Editing numeric values

Some parameters take numeric values without using sliders - for example, color matching values or IP addresses.

1. Use the UP and DOWN arrow buttons to highlight the row containing the numeric field you wish to edit.

2. Press ENTER/OK to enter edit mode. A numeric field in edit mode is white text on blue background.

3. In edit mode:

l Use the UP arrow button to increase the numeric value.

l Use the DOWN arrow button to decrease the numeric value.

4. Use the LEFT and RIGHT arrow buttons to edit the next or previous numeric fields within the same row.

5. Once ready, press ENTER/OK to exit edit mode.

Notes

Data

Row x: 0.658 y: 0.339

Highlighted Row x: 0.315 y: 0.662

Row x: 0.146 y: 0.043

Row x: 0.276 y: 0.283

Rev A June 2019

page38

Operating Guide

Using the projector Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Using the projector

Main menu

l Input

Press ENTER/OK to open the list of available inputs. Use the UP and DOWN arrow buttons to select an input from the list, then press ENTER/OK to confirm your choice. Press EXIT to return to the main menu.

l Test Pattern

Choose from: White, Black, Red, Green, Blue, Checkerboard, Crosshatch, V Burst, H Burst, Color Bar, Screen Layout, Off. Use the LEFT and RIGHT

arrow buttons to switch between values.

l Lens, Image, Color, Geometry, Edge Blend, 3D,

Laser, Setup and Network. Press ENTER/OK to open these menus and access various settings.

Press the DOWN arrow at the bottom of the page to access additional menus:

l PIP and Information

Press ENTER/OK to open these menus and access various settings.

Press the UP arrow to return to the previous page.

Main Menu

Input HDMI 1

Test Pattern

Lens ►

Image ►

Color ►

Geometry ►

Edge Blend ►

3D ►

Laser ►

Setup ►

Network ►

▼

Main Menu, page 1

Main Menu

▲

PIP ►

Information ►

Main menu, page 2

Notes

See Signal inputs on page26 for information about the available inputs and connections.

Selecting a test pattern hides the OSD. Press EXIT to hide the test pattern, and then press MENU to show the OSD

Operating Guide

Rev A June 2019

page39

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Using the projector

Lens menu

l Lens Lock

When this feature is On, all other Lens menu items are disabled.

l Lens Control

Opens a sub-menu, see below.

l Center Lens

Centers the lens.

l Lens Type

Choose a UST or a non-UST lens.

l Lens Memory

Opens a sub-menu, see next page.

Lens control

Lens Control settings operate in Zoom/Focus Adjustment and Shift Adjustment mode. Press ENTER/OK to

switch between modes.

When in Zoom/Focus Adjustment mode:

l Use the UP and DOWN arrow buttons to adjust Zoom.

l Use the LEFT and RIGHT arrow buttons to adjust Focus.

Notes

Lens

Lens Lock Off

Lens Control ►

Center Lens

Lens Type non-UST Lens

Lens Memory ►

Lens Control

Zoom

Focus

When in Shift Adjustment mode, use the arrow buttons to adjust Shift.

Rev A June 2019

page40

[OK] Shift Adjustment

Lens Control

Shift

[OK] Zoom / Focus Adjustment

Operating Guide

Using the projector Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Lens memory

This menu allows you to load, save and delete up to ten lens presets, containing position, zoom, focus and shift adjustment information.

For example, if using different screen sizes and aspect ratios, you can save zoom, focus and positioning for each screen size and aspect ratio in a dedicated preset.

Use Clear Memory to delete a memory preset if you need to save a new combination of lens settings in its place. Overwriting a saved memory preset is not possible.

Lens Save Memory

Memory 1

Memory 2

Memory 3

Memory 4

Memory 5

Memory 6

Memory 7

Memory 8

Memory 9

Memory 10

Lens Load Memory

Memory 1

Memory 2

Memory 3

Memory 4

Memory 5

Memory 6

Memory 7

Memory 8

Memory 9

Memory 10

Notes

Lens Memory

Load Memory ►

Save Memory ►

Clear Memory ►

Lens Clear Memory

Memory 1

Memory 2

Memory 3

Memory 4

Memory 5

Memory 6

Memory 7

Memory 8

Memory 9

Memory 10

Operating Guide

Rev A June 2019

page41

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Using the projector

Image menu

l Picture Mode

Choose from High Bright, Presentation and Video. Use a different setting depending the type of input source. Press ENTER/SELECT to open the list. Use the UP and DOWN arrow buttons to select a picture mode from the list, then press ENTER/OK to confirm your choice. Press EXIT to return to the main menu.

l Dynamic Black

Set to On to allow for increased contrast in darker scenes by modulating the light source.

l Light Off Timer

When Dynamic Black is On, the Light Off Timer will define if laser light source will turn off after a period of time has passed. The options are: Disable, 0.5, 1.0, 1.5, 2.0, 3.0, 4.0 seconds.

l Smooth Picture

When this feature is On, the projector will resize the incoming signal to display in 4K-UHD resolution. When Off sources will be displayed within WQXGA+ resolution. Auto will display 4K-UHD sources in 4K-UHD resolution with Smooth Picture On. Lower resolution sources will be displayed within WQXGA+ resolution with Smooth Picture Off. Aspect ratio selection applies for both Smooth Picture On or Off.

l Gamma

Choose a de-gamma curve from 1.0, 1.8, 2.0, 2.2, 2.35, 2.5, S-Curve, and DICOM. Used correctly, the Gamma setting can improve contrast while maintaining good details for blacks and whites. If excess ambient light washes out the image and it is difficult to see details in dark areas, lower the Gamma setting to compensate. This improves contrast while maintaining good details for blacks. Conversely, if the image is washed out and unnatural, with excessive detail in black areas, increase the setting.

S-Curve is an enhanced mid-tone gamma. DICOM is a simulated DICOM display, which can be used for training applications.

Image

Picture Mode High Bright

Light Off Timer Disabled

Dynamic Black Off

Smooth Picture Auto

Gamma 2.2

HDR Auto

Brightness 100

Contrast 100

Saturation 100

Hue 100

Sharpness 10

▼

Image

▲

Resync

Noise Reduction Off

Freeze

Notes

The following settings are not available with input HDMI 3 or HDMI 4: Image > Dynamic Black, Smooth Picture, Brightness, Contrast, Saturation, Hue, Sharpness, Noise Reduction, Freeze, Resync.

Color > Color Space. Geometry > Aspect Ratio,

Digital Zoom, Overscan. Setup > Screen Setting, Auto Source, Trigger-1, Trigger-2. PIP > all settings.

Rev A June 2019

page42

Operating Guide

Using the projector Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

l HDR

Choose from AUTO, HDRPQ-400, HDRPQ500, HDRPQ1000 and HDRHLG. HDR (High Dynamic Range) is a new form of gamma developed to create more realistic experience when viewing images delivered using this format, such as scenes with bright sunlight. Unlike traditional gamma HDR is not device or installation independent. HDR content will come with a recommended brightness regardless of screen size. For best results as a guideline the following screens sizes are suggested.

HDRScreen sizes Screen width (cm)

Model Lumens 400 NIT 500 NIT 1000 NIT

EVL 11000 4K 9,500 366.60cm 327.90cm 231.90cm

HDR options should only be used with media players and sources equipped with HDR and HDR content. Perceptual Quantizer (PQ) is the digitizing concept for capture and display and provides metadata to enable the display to understand the coding of the content. The NIT numbers relate to the brightness of the viewing conditions in NIT. NIT is the unit of brightness measurement for monitors and LED walls that emit light rather than reflect it such as a projection screen. However it is a reference to the brightness you would choose for a given environment. HDRHLG is High Dynamic Range – hybrid-log-gamma. This is a broadcast version of HDR for live TV and events.

l Brightness, Contrast, Saturation, Hue, Sharpness

Highlight the setting you wish to edit, and then press ENTER/OK, or the LEFT or RIGHT arrow button to open the slider. Use the LEFT and RIGHT arrow buttons to adjust the slider. Press EXIT to close the slider and return to the menu, or MENU to close the slider and return to the projected image.

l Resync

Press ENTER/OK to force the projector to resynchronise with the current input

l Noise Reduction

Choose a level of noise reduction from Off, Low, Middle and High.

l Freeze

Freezes the current frame.

Notes

Selecting a HDR setting will disable the Gamma setting. If the HDR setting is Auto, the Gamma setting is only disabled when the image source is HDR

The HDR AUTO setting is only available when the incoming signal is HDR capable

Brightness, Contrast, Saturation, Hue, Sharpness and Noise Reduction are not available with the HDMI 3 and HDMI 4 inputs

Operating Guide

Rev A June 2019

page43

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Using the projector

Color menu

Color space

In most cases, the Auto setting determines the correct colorspace to use. If it does not, you can choose a specific colorspace:

Choose from Auto, YPbPr, YCbCr, RGB PC and RGB Video.

Color

Color Space Auto

Color Mode ColorMax

ColorMax Peak

Manual Color Matching ►

Color Temperature Native

Gains and Lifts ►

Color

Color Space Auto

Color Mode

ColorMax

Manual Color Matching

Color Temperature

Gains and Lifts

Auto

YPbPr

YCbCr

RGB PC

RGB Video

Notes

Color Space is not

available with HDMI 3 or HDMI 4.

Rev A June 2019

page44

Operating Guide

Using the projector Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Color mode

The projector can work in the following color modes: ColorMax, Manual Color Matching, Color Temperature and Gains and Lifts.

ColorMax

1. Set Color Mode to ColorMax.

2. Navigate to the ColorMax setting.

3. Choose from HDTV, Peak, User 1 and User 2. User 1 and User 2 are user-defined color gamuts set via the Setup > ColorMax menu.

Color

Color Space Auto

Color Mode ColorMax

ColorMax

Manual Color Matching

Color Temperature

Gains and Lifts

ColorMax

ManualColor Matching

Color Temperature

Gains and Lifts

Color

Color Space Auto

Color Mode ColorMax

ColorMax Peak

Manual Color Matching

Color Temperature

Gains and Lifts

HDTV

Peak

User 1

User 2

Notes

Only one color mode can be selected at a time. Settings used by the other color modes are disabled.

See Setup menu on page72 for further information about setting up the User 1 and User 2 color gamuts.

Operating Guide

Rev A June 2019

page45

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Using the projector

Manual color matching

1. Set Color Mode to Manual Color Matching.

2. Open the Manual Color Matching submenu.

Here you can do the following:

l Switch Auto Test Pattern On and Off.

l Adjust Hue, Saturation and Gain settings for each individual color to improve the color balance of the

projected image.

l Adjust white balance RGB values.

l Reset all values.

Manual Color Matching - Red

Hue 100

Saturation 100

Gain 100

Manual Color Matching

Auto Test Pattern Off

Red ►

Green ►

Blue ►

Yellow ►

Cyan ►

Magenta ►

White Balance ►

Reset

Manual Color Matching - White Balance

Red 100

Green 100

Blue 100

Notes

See Color matching parameters explained on the facing page for more details about the Hue, Saturation and Gain settings.

Rev A June 2019

page46

Operating Guide

Using the projector Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Color matching parameters explained

The levels of hue, saturation and gain in the Manual Color Matching menu change the color values in the following ways:

1. Hue Specifies the position of each color (red, yellow, green, cyan, blue and magenta) relative to its neighboring colors.

2. Saturation Specifies the level of white in each color (i.e. how “pale” each color is).

3. Gain Controls the amount of light that goes into each color, i.e. the lowest gain would produce black.

Notes

Operating Guide

Rev A June 2019

page47

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Using the projector

Color temperature

1. Set Color Mode to Color Temperature.

2. Navigate to the Color Temperature setting. Choose a value from 3200K (warmer) to 9300K (cooler) or

Native (no correction).

Gains and lifts

1. Set Color Mode to Gains and Lifts.

2. Open the Gains and Lifts submenu.

Lifts allow you to adjust black levels of individual colors, while gains adjust the bright part of the scale.

Set the sliders as required

Color

Color Space Auto

Color Mode Color Temperature

ColorMax Peak

Manual Color Matching ►

Color Temperature Native

Gains and Lifts

3200K

5400K

6500K

7500K

9300K

Native

Gains and Lifts

Red Lift 100

Green Lift 100

Blue Lift 100

Red Gain 100

Green Gain 100

Blue Gain 100

Notes

Rev A June 2019

page48

Operating Guide

Using the projector Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Geometry menu

This menu allows you to compensate for image distortions caused by an unusual projection angle or irregular screen surface.

Aspect ratio

This feature defines the aspect ratio of the source. Use the Setup > Screen Setting to define the screen aspect ratio.

If you choose a preset aspect ratio from here, it will give you the best fit for your selection.

Choose from:

l 5:4

l 4:3

l 16:10

l 16:9

l 1.88

l 2.35

l TheaterScope

l Source

l Unscaled

Geometry

Aspect Ratio Source

Digital Zoom ►

Overscan Off

Blanking ►

Keystone ►

4 Corners ►

Rotation ►

Pincushion / Barrel ►

Arc ►

Custom Warp ►

Notes

Aspect Ratio, Digital Zoom and Overscan are

not available with input HDMI 3 or HDMI 4.

Only one of the following should be used at any one time: Keystone, 4

Corners, Rotation, Pincushion/Barrel and Arc. For more complex adjustments use Custom Warp later in this section

Image scaling and aspect ratio are also influenced by Setup > Screen Setting.

See Theaterscope setting on the next page for further information about the TheaterScope aspect ratio.

Operating Guide

Rev A June 2019

page49

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Using the projector

Black margin – part of the source

Theaterscope setting

The TheaterScope setting is used in combination with an anamorphic lens to restore 2.35: images packed into a 16:9 frame. Such images are projected with black lines at the top and bottom of the 16:9 screen to make up for the difference in aspect ratios.

Without an anamorphic lens and without the TheaterScope setting applied, a 16:9 source containing a 2.35:1 image looks like this:

If we change the setting to TheaterScope, the black lines will disappear but the image will stretch vertically to reach the top and bottom of the DMD™:

An anamorphic lens will stretch the image horizontally, restoring the original 2.35 ratio:

Notes

TheaterScope is used with an anamorphic lens.

If you use TheaterScope, set your screen aspect ratio to 16:9.

Rev A June 2019

page50

Operating Guide

Using the projector Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Digital zoom

Digital zooming enlarges a section of the image, while the area outside the enlarged section is cropped out to preserve the overall image size.

l Digital Zoom defines the level of zoom that needs to be applied. If Digital Zoom is set to 0, then the other

settings in the menu will be disabled.

l Digital Pan and Digital Scan specify the area that is being enlarged:

l Digital Pan adjusts the horizontal coordinates.

l Digital Scan adjusts the vertical coordinates.

The Reset command restores the default Digital Zoom, Digital Pan and Digital Scan values.

Digital Zoom

Digital Zoom 0

Digital Pan 0

Digital Scan 0

Reset

Notes

Digital Zoom is not

available with input HDMI 3 or HDMI 4.

Digital Zoom is a temporary setting and not retained after an input change or power cycle.

Operating Guide

Rev A June 2019

page51

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Using the projector

Overscan

Use this setting to compensate for noisy or badly defined image edges.

Crop removes unwanted artifacts from the edges of your image by cropping the edges.

Zoom increases the size of the image to force the edges off-screen

Geometry

Aspect Ratio Source

Digital Zoom ►

Overscan Off

Blanking

Keystone

4 Corners

Rotation

Pincushion / Barrel ►

Arc ►

Off

Crop

Zoom

Notes

Overscan is not available

with input HDMI 3 or HDMI

Rev A June 2019

page52

Operating Guide

Using the projector Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Blanking

Use this feature to:

l fit an odd-sized screen;

l cut off timecode dots in the top line of a picture;

l cut off subtitles, etc.

Select the edge you wish to blank and use the LEFT and RIGHT arrow buttons to determine the amount of correction.

Use the Reset command to restore blanked edges.

Notes

Blanking

Top 0

Bottom 0

Left 0

Right 0

Reset

Operating Guide

Rev A June 2019

page53

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Using the projector

Keystone

Use this setting to compensate for any distortion caused by the projector being in a different horizontal or vertical plane to the screen.

Keystone

H Keystone 0

V Keystone 0

Rotation 0

Reset

Notes

Max rotation in Keystone is reduced from normal rotation

Rev A June 2019

page54

Operating Guide

Using the projector Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Keystone example

Notes

The resulting image is distortedThe projector is positioned at an angle

The image is corrected when Keystone is

applied

Operating Guide

Rev A June 2019

page55

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Using the projector

3 4 5

Keystone settings

1. Projector to the left The projector is positioned to the left of the screen. To correct, apply a positive Horizontal Keystone value using the RIGHT arrow button.

2. Projector to the right The projector is positioned to the right of the screen. To correct, apply a negative Horizontal Keystone value using the LEFT arrow button.

3. Projector high The projector is positioned above the screen at a downward angle. To correct, apply a negative Vertical Keystone value using the DOWN arrow button.

4. Projector low The projector is positioned below the screen at an upward angle. To correct, apply a positive Vertical Keystone value using the UP arrow button.

5. Projector straight The projector is directly opposite the screen at a right angle both horizontally and vertically. No correction is needed.

Notes

Rev A June 2019

page56

Horizontal and vertical keystone corrections

Operating Guide

Using the projector Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

4 corners

For each corner, apply horizontal and / or vertical correction as necessary to restore the rectangular shape of the image.

4 Corners

Top Left Corner ►

Top Right Corner ►

Bottom Left Corner ►

Bottom Right Corner ►

Reset

Notes

Corner corrections provide a simple setup for awkward installations and irregular shaped screens that may distort the image. To apply a similar (but less flexible) correction, while preserving the original aspect ratio of the image, use the Keystone menu.

Operating Guide

Rev A June 2019

page57

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Using the projector

Top right corner example

In this illustration, the top right corner requires both horizontal and vertical correction.

Notes

Top Right Corner Adjustment

Top Right Corner x 0

Top Right Corner y 0

Rev A June 2019

page58

Operating Guide

Using the projector Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Rotation

Use this feature for example to correct a mounting error causing the image not to be level with the screen.

Notes

Rotation

Rotation 0

Reset

Operating Guide

Rev A June 2019

page59

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Using the projector

123

Rotation example

1. DMD™ area The DMD™ is not rotated. It still covers the area that would be occupied by the image without correction.

2. Rotated image The image is smaller than the surrounding DMD™ area. It is scaled in order to remain within the DMD™ area.

3. Angle of rotation Each step on the slider is 0.25° of rotation. In this example the angle is 5°, therefore Rotation value is 20.

Notes

Rev A June 2019

page60

Operating Guide

Using the projector Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Pincushion / barrel

Pincushion or barrel distortions are the result of poor or incorrect tensioning of the screen or using a surface that is not flat.

Use the Pincushion / Barrel control to compensate electronically for such distortions.

You can also use this menu to make simple panoramic screen corrections without using external processors.

Pincushion/ Barrel example

The illustration shows pincushion and barrel correction applied both horizontally and vertically, in equal measures.

Notes

Pincushion / Barrel

H Pin/Barrel 0

V Pin/Barrel 0

Keystone ►

Reset

Operating Guide

BarrelPincushion

Rev A June 2019

page61

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Using the projector

Arc

This feature is similar to Pincushion / Barrel but allows you to apply curvature to each edge of the image independently so you can have any combination of corrections.

Arc

Top 0

Bottom 0

Left 0

Right 0

Reset

Notes

Please note that a positive Arc value on any edge will reduce the image size as the projector needs to maintain the aspect ratio. A negative Arc value will not affect the overall image size.

Rev A June 2019

page62

Operating Guide

Using the projector Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Custom warp

This feature permits selection of predefined User warp maps. Use the Projector Controller PC application to create the custom warp maps.

Custom warp maps provide non-linear curvature correction for curved or spherical screens and other irregular shaped surfaces such as building mapping.

Notes

Custom Warp

Off

User 1

User 2

Operating Guide

Rev A June 2019

page63

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Using the projector

Edge blend menu

Use this menu to blend together images from an array of two or more projectors. The feature feathers the light output of the projector within the edges that overlap with other projectors in the array: as a result, the overlapping edges are evenly lit and easily blend in with the rest of the image.

l Edge Blend

Enable and disable Edge Blend

l Align Pattern

Add markers to the image showing the edges of the blend area and making the overlaps more visible to help adjust the physical position of the projectors in the array.

l Blend Width

Determine the width of the blended regions.

l Black Level Uplift

Adjust black levels to compensate if the blended regions appear brighter than the rest of the image.

l Reset

Reset all Edge Blend settings to their factory default values.

Edge Blend

Edge Blend On

Align Pattern Off

Blend Width ►

Black Level Uplift ►

Reset

Notes

When Edge Blend is set to Off, all other edge blend

settings are disabled.

The picture in the blend region needs to be delivered to all overlapping projectors, which may require a special setup of the source.

Rev A June 2019

page64

Operating Guide

Using the projector Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

123

Blend width

Use the LEFT and RIGHT arrow buttons to set the width of the blended regions:

1. Top

2. Bottom

3. Left

4. Right

Notes

Blend Width

Top 0

Bottom 0

Left 0

Right 0

Operating Guide

Rev A June 2019

page65

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Using the projector

123

Black level uplift

Black in the blended regions appears less dark than in the rest of the image. To compensate for this, use this menu to raise the black levels of the rest of the image:

l Set All to the required amount of black level correction. This will apply equal correction to the black

levels of all colors

l If necessary, use the individual color sliders (Red, Green and Blue) for fine adjustment.

You may experience artifacts at the edges where the blended region of one projector overlaps the pond of

mirrors of its neighbor. In the example below, the blended image comes from two projectors,1and2. Both

images have black level uplift applied; as a result, artifacts3and4have emerged at the edges where the black level uplift region of one projector overlaps the pond of mirrors of the other.

To remove the artifacts, you need to slightly reduce the size of the black level uplift region of each projector so it does not overlap the pond of mirrors of the other projector.

l Depending on your array, use Top, Bottom, Left and/or Right to reduce the black level uplift size. In the

example below, use the Right slider of the projector on the left1to remove the artifact on the right

, and the Left slider of the projector on the right2to remove the artifact on the left3.

Black Level Uplift

Select Area

Top 0

Bottom 0

Left 0

Right 0

Color Adjustment

All ◄ ►

Red 0

Green 0

Blue 0

Notes

Enable Align Pattern from the Edge Blend menu to see the black level uplift area.

Rev A June 2019

page66

Operating Guide

Using the projector Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

3D menu

Use this menu to enable, disable and set up 3D input, as follows:

l 3D Format — Off, Dual Pipe and Frame Sequential.

Frame Sequential is for sources where Left and Right eye images are delivered as alternate frames from a single input. Dual Pipe is for sources where Left and Right eye are delivered on separate inputs.

l DLP Link — Off / On.

DLP Link On emits a sync pulse for the 3D glasses via the projected image. DLP Link Off will send the sync pulse to the sync out connector to use with an external third party emitter.

l Eye Swap — Normal and Reverse.

(set to Reverse if the left- and right-eye images are displayed in the wrong order)

l Dark Time — 0.65 ms, 1.3 ms and 1.95 ms.

Set to reduce the effect of banding and image overlapping when viewed through 3D glasses.

l Sync Offset.

Use the LEFT and RIGHT arrow buttons to compensate for image overlapping (ghosting) when viewed through 3D glasses.

l Sync Reference— External and Internal.

Select the source of the 3D sync. Internal is referenced to the incoming video. External is for Frame Sequential 3D sources and is supplied by the graphics card or player.

3D Format Auto

DLP Link Off

Eye Swap Normal

Dark Time 1.95 ms

Sync Offset 100

Sync Reference Internal

Notes

3D video is only possible on the HDMI 3 and HDMI 4 inputs.

If 3D Format is set to Off, all other 3D settings will be unavailable.

See 3D connections on page28 for more information about supported 3D formats.

The following settings are not available when 3D is on: Image > Smooth Picture, Brightness, Contrast, Saturation, Hue, Sharpness, Noise Reduction, Freeze, Resync.

Color > Color Space. Geometry > Aspect Ratio,

Digital Zoom, Overscan. Setup > Screen Setting, Auto Source, Trigger-1, Trigger-2. PIP > all settings.

Operating Guide

Also: See 3D types on the next page and See Some 3D settings explained on page69

See 3D formats on page112 for 3D resolutions and frame rates.

Rev A June 2019

page67

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Using the projector

HDMI 1

HDMI 2

L R L R

3D types

To display a 3D image if is first necessary to select the 3D format. This can either be Frame Sequential or Dual Pipe. These formats are described below:

l Dual Pipe (LEFT and RIGHT) The left and right eye images are delivered on two separate

HDMI links, which the projector will interleave for 3D display.

l Frame Sequential For sequential 3D, an external sync is required to identify left and right

frames. If no sync is available from the sequential source, the projector will generate an output sync, but it may then be necessary to manually set the Eye Swap each time the player is started.

Dark Time and Sync Offset need to be set only once, to optimize the image for the glasses in use.

Dual Pipe

Notes

Rev A June 2019

page68

Sequential

Operating Guide

Using the projector Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Fully On

Fully Off

Left Right

Dark Time

LEFT 1 LEFT 2 LEFT 3RIGHT 1 RIGHT 2 RIGHT 3

Some 3D settings explained

Dark time

Banding can be caused if the image is displayed before each eye of the 3D switching glasses or ZScreen is not fully open.

Dark Time allows you to minimize this effect.

Eye swap

The outgoing 3D frames are in pairs - the dominant frame being presented first. You can determine which frame should be the dominant one.

By convention the default setting is Left.

Notes

In order to achieve maximum light output and a smooth grayscale, whilst eliminating ghosting, the following procedure is recommended:

1. Set Dark Time to a value appropriate to the glasses or ZScreen, say

1.3 ms or 1.95 ms.

2. Adjust Sync Offset time to eliminate ghosting and achieve a smooth grayscale.

3. Repeat steps 1 and 2 until the best result is obtained.

Dominance Left

Operating Guide

Dominance Right

Rev A June 2019

page69

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Using the projector

Incoming video

Incoming sync signal

Video signal with processing

delays (and dark time

adjustment)

Sync output signal after

delay adjustments

Sync offset

The sync signal from the 3D server will be in phase with the frames generated by its graphics card. However, to compensate for switching delays in the glasses or ZScreen, Sync Offset is used to adjust the sync output signal sent to the ZScreen or 3D glasses to minimise overlapping (ghosting in the image when viewed through the 3D glasses.

Notes

Rev A June 2019

page70

Operating Guide

Using the projector Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Laser menu

l Power Mode

l Eco will automatically set the laser power to 80%.

l Normal will set the power to 100%.

l Set to Custom if you wish to adjust the power manually.

l Power Level

This setting is only available if Power Mode is set to Custom. Choose a value between 20 and 100, ranging from 20% to 100% laser power.

l Constant Brightness

Once a Custom Power Mode has been set, then Constant Brightness can be turned ON. This setting will maintain the brightness until the maximum laser power has been reached. The lower the power level the longer it will be maintained.

Notes

Laser

Power Mode Normal

Power Level – – – –

Constant Brightness Off

Operating Guide

Rev A June 2019

page71

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Using the projector

Setup menu

l Orientation

Choose from Front Tabletop, Front Ceiling, Rear Tabletop, Rear Ceiling and Auto-front.

l Cooling Condition

Choose from Table, Ceiling, Freetilt and Auto.

l High Altitude

Choose from On, Auto and Quiet.

l Standby Power

Choose from SuperECO, ECO and Normal. SuperECO uses minimal power and disables power ON via LAN. ECO uses a low power setting but enables power ON via Ethernet port only. Normal enables power ON via both HDBase-T/LAN and Ethernet ports.

l Screen Setting

Choose from 16:10, 16:9 and 4:3.

l ColorMax

Set up user-defined color gamut values.

l Power On/Off Management

Access the submenu to set up automatic projector power on and power off.

l Clock Adjust

Access the submenu to set current date and local time.

l Startup Logo

Set this to On if you want the DP logo to show when the projector is first switched on.

l Blank Screen

Choose from Logo, Black, Blue and White.

l Auto Source

If this setting is On, the projector will automatically search for an active input source.

Setup

Orientation Auto-front

Cooling Condition Auto

High Altitude Auto

Standby Power SuperECO

Screen Setting 16:9

ColorMax ►

Power on/off Management

Clock Adjust ►

Startup Logo On

Blank Screen Logo

Auto Source Off

▼

►

Notes

Auto-front automatically

detects the projector’s position and sets Table or Ceiling orientation accordingly.

Screen Setting and Auto Source are not available

with input HDMI 3 or HDMI 4

Screen Setting is automatically set to 16:9 when smooth picture is active

Highlight the DOWN arrow at the bottom of the page and press ENTER/OK to navigate to the second Setup menu page.

Rev A June 2019

page72

Operating Guide

Using the projector Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

l Trigger1 and Trigger 2

Setup

Choose from Screen, 5:4, 4:3, 16:10, 16:9, 1.88, 2.35, TheaterScope, Source, Unscaled or RS232 to determine what will cause each trigger output to activate.

l Infrared Remote

Set to Off if you wish to disable the remote control.

l IR Code

The projector and the remote control need a matching IR code: a two-digit number between 00 and 99. The default IR code is 00. This is also a master code, which, if assigned to a remote, will work regardless of the value assigned to the projector.

l To assign an IR code for the projector: Select IR code. Use the UP and DOWN arrow buttons to

change the values.

l To assign an IR code for the remote, press and hold the ADDR button on the remote until the

On indicator starts flashing. Release the ADDR button and while the indicator is still flashing, enter a two digit address using the numeric input buttons. The indicator will flash three times quickly to confirm the change.

l IR Code Reset

Trigger-1 Off

Trigger-2 Off

Infrared Remote On

IR Code 0

IR Code Reset

OSD Settings ►

Memory ►

Instant Startup Off

Standby Period 30 Min.

HDMI Equalizer Off

Image Latency Normal

▲

Use this command to unassign an IR code from the projector. This will revert the IR Code value to 00. To unassign an IR code from the remote control, press and hold ALT and ADDR simultaneously until

the On indicator flashes to confirm the change.

l OSD Settings

Access this submenu to adjust the appearance and position of the on-screen display.

l Memory

Access this submenu to save up to four presets containing custom combinations of image settings, or to recall a saved preset.

l Instant Startup

When ON only the Laser will be turned off when the Power off command is given. A subsequent Power On will turn on the laser giving an apparent very fast power on.

l Standby Period

Used with Instant Startup. If Instant Startup in ON and the projector is powered down then the projector will go to Standby after the selected “Standby Period” 30 minutes, 60 minutes, 90 minutes.

l HDMI Equaliser

Select ON to activate the HDMI Equalizer. When transmitting signals via a HDMI cable, signal noise can disrupt the information received by the projector. High bandwidth signals, poor quality HDMI cables and longer HDMI cables can increase the signal noise. Use the HDMI Equaliser to improve HDMI signal acquisition.

l Image Latency

Select Fast for improved latency. Select Normal when image corruption occurs. Image corruption (frame tearing) may occur when a high level of warping is applied to the image and fast latency is selected. See Geometry menu on page49 for information about image warping.

Notes

Trigger-1 and Trigger-2

are not available with input HDMI 3 or HDMI 4. If you turn the remote control off, you can only turn it back on again from the control panel or via the

Projector Controller

application.

The Projector Controller software is available for download from the Digital Projection website, free of charge.

A wired remote control will also be disabled if

Infrared Remote is set to Off.

Highlight the UP arrow at the top of the page and press ENTER/OK to go back to the first Setup menu page.

Operating Guide

Rev A June 2019

page73

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Using the projector

ColorMax

ColorMax permits seven point color matching of red, green, blue, yellow, cyan, magenta and white.

You can enter your own gamut values here, or edit values you have imported using the Projector Controller software.

Defining your own colorspace with individual x and y coordinates for each color enables you to match not only the whites but each individual color as well.

Highlight the submenu you wish to open and press ENTER/OK to confirm your choice.

Measured data/ target data

1. Use the UP and DOWN arrow buttons to highlight a color, then use the LEFT and RIGHT arrow buttons to navigate to the x or y coordinate.

2. Use the UP and DOWN arrow buttons to increase and decrease the value, respectively.

3. Exit edit mode:

l press ENTER/OK, if you want to save the

edited values.

l press EXIT, if you do not wish to save the

edited values

4. If necessary, highlight another color and repeat the procedure.

Red x: 0.658 y: 0.339

Green x: 0.315 y: 0.662

Blue x: 0.146 y: 0.043

White x: 0.276 y 0.283

Reset

Measured Data

ColorMax

Measured Data ►

Target Data - User1 ►

Target Data - User 2 ►

Target Data - User1

Red x: 0.640 y: 0.390

Green x:0.300 y: 0.600

Blue x: 0.150 y: 0.060

Yellow x: 0.419 y: 0.505

Cyan x: 0.225 y: 0.329

Magenta x: 0.321 y: 0.154

White x: 0.285 y: 0.302

Notes

The Projector Controller software is available for download from the Digital Projection website, free of charge.

This tool is best used in conjunction with a specialized light meter (a photo spectrometer) to measure color parameters within a particular installation. However, the preloaded generic factory default data set is designed to give more than satisfactory results.

Rev A June 2019

page74

Operating Guide

Using the projector Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Power on / off

l Auto Power Off

Set this to On if you want the projector to go into STANDBY mode when no input source is detected for 20 minutes.

l Auto Power On

Set this to On if you want the projector to start up immediately when the mains is connected. Set this to Off if you want the projector to go into STANDBY mode when the mains is connected. In this case, the

projector will not start up until the POWER button is pressed on the control panel or the ON button is pressed on the remote control.

l Scheduled on/off

Access this submenu to create a weekly schedule for automatic on and off times:

1. Set a schedule:

2. To enable the schedule, set Schedule to On.

l Use the UP and DOWN arrow buttons to highlight a row, then press ENTER/OK to enable

edit mode.

l Within a row, navigate with the LEFT and RIGHT arrow buttons. Set values with the UP

and DOWN arrow buttons.

l To exit edit mode, press ENTER/OK. Alternatively, press EXIT if you don’t want the

changes to take effect. Move to another row using the UP and DOWN arrow buttons.

Power on/off Management

Auto Power Off Off

Auto Power On Off

Scheduled on-off ►

Scheduled on-off

Schedule Off

S M T W T F S

On 12:34

Time

Notes

Operating Guide

Off 12:34

On 12:34

Off 12:34

Rev A June 2019

page75

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Using the projector

Clock adjust

Use this menu to set date (in dd:MM:yyyy format), time (in HH:mm format) and time zone.

The date and time set here will affect any schedule created within the Power On/Off menu.

OSDsettings

l Language sets the OSD language.

l Menu Position determines where the OSD should appear on the screen when activated.

l Menu Transparency sets OSD transparency between 0% (no transparency), 25%, 50% and 75%.

l Time Out determines how long the OSD should remain on screen if no buttons are pressed. Choose

Always On to disable this feature.

l Message Box determines whether projector status messages should appear on the screen.

Notes

Clock Adjust

Date (dd:MM:yyyy) 30:11:2017

Time (HH:mm) 16:00

Time Zone UTC 00

OSD Settings

Language English

Menu Position Center

Menu Transparency 0

Time Out 30 Seconds

Message Box On

Rev A June 2019

page76

Operating Guide

Using the projector Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Memory

The current image settings can be saved as a preset, which you can recall later. The default settings can be recalled at any time as well.

Up to four custom presets can be stored for each input.

The following settings are saved in a preset:

l From the Image menu — Dynamic Black, Smooth Picture, Gamma, Brightness, Contrast, Saturation,

Hue, Sharpness and Noise Reduction

l From the Color menu — Color Space, Color Mode, ColorMax, Color Temperature, Dynamic Black,

RGB Lift and RGB Gain

l From the Geometry menu — Aspect Ratio and Overscan.

To recall a saved preset:

l Select Recall Memory and press ENTER/OK, then select a preset from Preset A to Preset D. Select

Default to load factory default values.

To save a preset:

l Select Save Settings and press ENTER/OK, then choose from Preset A, Preset B, Preset C and

Preset D.

Memory

Recall Memory Default

Save Settings Preset A

Notes

Presets from one input cannot be applied to another input.

Presets for inputs HDMI 3 and 4 do not contain all the settings normally stored for other inputs.

See on page1 for information about the parameters that can be saved in a memory preset.

Operating Guide

Rev A June 2019

page77

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Using the projector

Network menu

l DHCP, IP, Subnet Mask, Gateway, DNS

Set DHCP to On if the IP address is to be assigned by a DHCP server, or Off if it is to be set here. If DHCP is On, it will not be possible to edit IP Address, Subnet Mask, Gateway or DNS. If DHCP is set to Off, edit IP Address, Subnet Mask, Gateway and DNS as required.

l MAC This field is read-only.

l AMX Switch on or off

Notes

Network

DHCP Off

IP 192.168.000. 10

Subnet Mask 255. 255 .255 .000

Gateway 000.000. 000 .000

DNS 000.000.000. 000

MAC 00:18:28:2d: f2:06

AMX Off

Rev A June 2019

page78

Operating Guide

Using the projector Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

PIP menu

l PIP Turn PIP on and off.

l Source Select an input source for the PIP image. Any combinations are possible between main and PIP

input source, as long as one of the inputs is either DisplayPort or 3G-SDI.

l Position Set the location of the PIP image on the screen. Choose from Top-Left, Top-Right, Bottom-Left,

Bottom-Right and PBP.

PIP

PIP Off

Source HDMI1

Position Top-Left

Notes

PIP functionality is not

available with inputs HDMI 3 and HDMI 4

Operating Guide

Rev A June 2019

page79

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Using the projector

Information menu

This menu gives information about software and hardware configuration, input source and laser operating times It also allows you to restore the factory default settings.

Signal format

Information

Model Name E-VisionLaser110004K

Serial Number X000XXXXX0000

Software Version 1 MD03-SE10-FE09

Software Version 2 STEP_D08-24-17-3120

Software Version 3 2.0.16.0-P503

Active / PIP Source HDMI 1

Signal Format ►

Laser Hours 2

System Status ►

Thermal Status ►

Factory Reset

Signal Format

Active Source

Timing 1080p/60Hz

H Refresh 67.500 KHz

V Refresh 60.00 Hz

Pixel Clock 148.500 MHz

Notes

PIP Source items are not

available with input HDMI 3 or HDMI 4.

Rev A June 2019

page80

PIP Source

Timing 576p/50Hz

H Refresh 31.250 KHz

V Refresh 50.00 Hz

Pixel Clock 27.0 MHz

Operating Guide

Using the projector Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

System status

Thermal status

Notes

System Status

Atmospheric Pressure 98988 Pa (116m)

AC Voltage 160V - 264V

Ceiling Mode 0

Tilt Angle 4 deg

Portrait Angle 0 deg

Altitude Mode Auto

Laser Power 100%

License Key LicensePass,

Timeout,Not Expired

Constant Brightness Off

Thermal Status

Inlet 1-2 Temp. 24 / 34 (C)

DMD Temp. 38 (C)

LD 1-2 Temp. 49 / 42 (C)

Fan 1-3 Speed 1399 / 1402 / 4391

Fan 4-6 Speed 1310 / 1200 / 1205

Fan 7-9 Speed 1211 / 1407 / 1410

Fan 10-12 Speed 0 / 3005 / 3007

Fan 13 - 15 Speed 2986 / 2984 / 2984

Fan 16-18 Speed 3020 / NA / NA

Water Pump Speed 3506

Operating Guide

Rev A June 2019

page81

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Using the projector

Factory reset

To restore the factory default settings:

1. Navigate to Factory Reset and press ENTER/OK.

2. When prompted, press ENTER/OK to confirm your choice, or press EXIT to cancel.

Information

Model Name E-VisionLaser110004K

Serial Number X000XXXXX0000

Software Version 1 MD03-SE10-FE09

Factory Reset

Warning All user settings will be lost

Press OK to confirm Press Exit to cancel

Thermal Status ►

Factory Reset

Notes

Factory reset does not reset the Network settings, or High Altitude mode

Rev A June 2019

page82

Operating Guide

Served web pages Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Served web pages

The served web pages allow you to control the projector remotely via LAN.

The default IP address is 192.168.0.100.

Notes

Operating Guide

Rev A June 2019

page83

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Served web pages

Notes

Rev A June 2019

page84

Operating Guide

Served web pages Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Notes

Operating Guide

Rev A June 2019

page85

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Served web pages

Notes

Rev A June 2019

page86

Operating Guide

Served web pages Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Notes

Operating Guide

Rev A June 2019

page87

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Served web pages

Notes

Rev A June 2019

page88

Operating Guide

Served web pages Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Notes

Operating Guide

Rev A June 2019

page89

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Served web pages

Notes

Rev A June 2019

page90

Operating Guide

Served web pages Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Notes

Operating Guide

Rev A June 2019

page91

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Served web pages

Notes

Rev A June 2019

page92

Operating Guide

Served web pages Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Notes

Operating Guide

Rev A June 2019

page93

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

This page is intentionally left blank

Rev A June 2019

E-Vision Laser11000 4K-UHD Series

High Brightness Digital Video Projector

REFERENCE GUIDE

Rev A June 2019

120-091A

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Choosing a lens

Choosing a lens

A number of lenses are available. Which lens you choose depends on the screen size, image aspect ratio, throw distance and light output.

The following table shows all available lenses in order of their throw ratios:

Throw Ratio Focus Range Lens Shift Part Number

0.377 : 1 fixed (UST) 0.82 m - 2.71 m Depends on image size, see UST Lens Installation Guide (separate document) 117-341

0.74 - 0.93 : 1 zoom 1.02 m - 12.7 m

0.76 : 1 fixed 0.81 m - 5.08 m none 112-499

1.24 - 1.78 : 1 zoom 1.33 m - 11.73 m

1.71 - 2.25 : 1 zoom 1.83 m - 14.9 m

2.20 - 3.67 : 1 zoom 2.36 m - 24.2 m

3.54 - 5.36 : 1 zoom 3.8 m - 35.35 m

5.24 - 8.27 : 1 zoom 5.59 m - 54.8 m

To choose a lens, calculate the throw ratio required. Allow a tolerance of +/- 3% in the throw ratio calculation.

V: 0.5 (U) 0.3 (D) frame H: 0.1 (L) 0.2 (R) frame

115-339

112-500

112-501

112-502

112-503

112-504

Notes

Throw distance calculations are based on the distance from the outer end of the lens, which varies from lens to lens. The lens extension is the distance between the front of the projector chassis and the outer end of the lens when it is fully extended.

Refer to the projector CAD drawings for individual lens extension figures.

The 0.377 : 1 fixed lens has no adjustable shift value. However, the lens has an inherent offset depending on image size. See the UST documentation published separately on the Digital Projection website.

Rev A June 2019

page96

The 0.74 - 0.93 : 1 zoom lens has a feature that

permits focus correction for curved screens. The front ring of the lens is a manual control that provides focus curvature adjustment to correct for the different focal distances between center and corner.

ReferenceGuide

Choosing a lens Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Basic calculation

Identify the required lens by calculating the throw ratio.

A throw ratio is the ratio of the throw distance2to the screen width1:

1. Use the formula above to obtain the required throw ratio.

2. Allow a tolerance of +/- 3% in the throw ratio calculation and match the throw ratio with a lens from the table below:

Throw ratios Focus range

0.377 : 1 fixed (UST) 0.82 m - 2.71 m

0.74 - 0.93 : 1 zoom 1.02 m - 12.7 m

0.76 : 1 fixed 0.81 m - 5.08 m

1.24 - 1.78 : 1 zoom 1.33 m - 11.73 m

1.71 - 2.25 : 1 zoom 1.83 m - 14.9 m

2.20 - 3.67 : 1 zoom 2.36 m - 24.2 m

3.54 - 5.36 : 1 zoom 3.8 m - 35.35 m

5.24 - 8.27 : 1 zoom 5.59 m - 54.8 m

3. Ensure the required throw distance is within the range covered by the lens.

Notes

The basic calculation on this page does not take into consideration DMD™ and image size, which could affect the throw ratio.See Full lens calculation on page99 for a more complex and realistic calculation.

When calculating the throw ratio, be sure to use identical measurement units for both the throw distance and the screen width.

See Choosing a lens on the previous page for information about individual lens part numbers

ReferenceGuide

Rev A June 2019

page97

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Choosing a lens

Basic calculation example

1. Calculate the throw ratio using the formula. Your screen is 4.5m wide and you wish to place the projector approximately 11m from the screen. The throw ratio will then be

11 ÷ 4.5= 2.44

2. Match the result with the lens table. The lens matching a throw ratio of 2.44 is the 2.20 - 3.67 : 1 zoom lens .

3. Check whether the lens covers the required throw distance. The focus range quoted for the 2.20 - 3.67 : 1 zoom lens is 2.36 - 24.2m.The required distance of 11m is within the range.

INFORMATION YOU NEED FOR THIS CALCULATION

The throw ratio formula:

Allow a tolerance of +/- 3% in the throw ratio calculation.

The lens table:

Throw ratios Focus range

0.377 : 1 fixed (UST) 0.82 m - 2.71 m

0.74 - 0.93 : 1 zoom 1.02 m - 12.7 m

0.76 : 1 fixed 0.81 m - 5.08 m

1.24 - 1.78 : 1 zoom 1.33 m - 11.73 m

1.71 - 2.25 : 1 zoom 1.83 m - 14.9 m

2.20 - 3.67 : 1 zoom 2.36 m - 24.2 m

3.54 - 5.36 : 1 zoom 3.8 m - 35.35 m

5.24 - 8.27 : 1 zoom 5.59 m - 54.8 m

Notes

The basic calculation on this page does not take into consideration DMD™ and image size, which could affect the throw ratio.See Full lens calculation on the facing page for a more complex and realistic calculation.

See Choosing a lens on page96 for information about individual lens part numbers.

Rev A June 2019

page98

ReferenceGuide

Choosing a lens Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series

Fig 1

Fig 2

Fig 3

Full lens calculation

Introducing TRC

The choice of lens will affect the image size and will address discrepancies between the DMD™ resolution and the source.

When an image fills the height of the DMD™ but not the width, it uses less than 100% of the DMD™ surface. A lens chosen using the basic formula may produce an image that is considerably smaller than the actual screen.

To compensate for loss of screen space in such situations, you need to increase the throw ratio using a Throw Ratio Correction (TRC).

Example

Fig. 1 illustrates a 4:3 image within a 16:9 display

When a 16:9 projector is used for a 4:3 image, the image does not fill the width of the DMD™, creating a pillarboxing effect - blank spaces to the left and right.

Fig. 2 shows the same image projected on a 4:3 screen using a standard lens (chosen with the basic calculation).

The DMD™ accurately fills the width of the screen; however, the pillarboxing is now part of the projected image and is transferred to the screen.

The DMD™ does not fill the height of the screen, which has caused letterboxing - further blank spaces at the top and bottom of the screen.

The image is now surrounded by blank space, which can be removed if the throw ratio is increased.

Notes

TRC can only be applied if greater than 1. If TRC is 1 or less, disregard it and calculate the throw ratio using the basic formula.

Fig. 3 shows the image projected on the same screen with a lens chosen using TRC. The increased throw ratio has allowed the 4:3 image to fill the 4:3 screen seamlessly

ReferenceGuide

Rev A June 2019

page99

Digital Projection Ltd. E-Vision Laser 11000 4K-UHD Series Choosing a lens

Calculating TRC

To calculate TRC, use the following formula:

TRC table

Alternatively, you can save time by referencing the following table, which shows the TRC value for some popular image formats:

2.35:1 (Scope) 3840 x 1634 pixels TRC < 1, not used

1.85:1 (Flat) 3840 x 2075 pixels TRC < 1, not used

1.78:1 (16:9) 3840 x 2160 pixels TRC = 1, not used (native aspect ratio)

1.6:1 (16:10) 3456 x 2160 pixels TRC = 1.11

1.33:1 (4:3) 2873 x 2160 pixels TRC = 1.33

1.25:1 (5:4) 2700 x 2160 pixels TRC = 1.42

Calculating the throw ratio with TRC

1. For TRC > 1, amend the basic throw ratio formula as follows:

Allow a tolerance of +/- 3% in the throw ratio calculation.

2. Once a throw ratio is established, identify the matching lens from the table:

Throw ratios Focus range

0.377 : 1 fixed (UST) 0.82 m - 2.71 m

0.74 - 0.93 : 1 zoom 1.02 m - 12.7 m

0.76 : 1 fixed 0.81 m - 5.08 m

1.24 - 1.78 : 1 zoom 1.33 m - 11.73 m

1.71 - 2.25 : 1 zoom 1.83 m - 14.9 m

2.20 - 3.67 : 1 zoom 2.36 m - 24.2 m

3.54 - 5.36 : 1 zoom 3.8 m - 35.35 m

5.24 - 8.27 : 1 zoom 5.59 m - 54.8 m

3. Ensure the required throw distance is within the range of the matching lens.

Notes

TRC can only be applied if greater than 1. If TRC is 1 or less, disregard it and calculate the throw ratio using the basic formula.

TRC can only be applied if greater than 1. If TRC is 1 or less, disregard it and calculate the throw ratio using the basic formula

Rev A June 2019

page100

ReferenceGuide

Digital Projection E-Vision Laser 11000 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

About this document

Symbols used in this document

Product revision

Legal notice

Laser information

Optical radiation

Introduction

Contents

What's in the box?

Connecting the power supply

Voltage selection

Projector overview

Control panel

Projector indicators

Remote control

Infrared reception

Positioning the screen and projector

Roll and pitch

Changing the lens

Inserting a new lens

Removing the lens

Operating the projector

Switching the projector on

Switching the projector off

Selecting an input signal

Selecting a test pattern

Adjusting the lens

Lens menu

Remote control

Adjusting the image

Orientation

Geometry

Picture

Signal inputs

Digital inputs and outputs

EDID on the DisplayPort, HDMI, and HDbaseT inputs

Using DisplayPort/ HDMI/ HDBaseT switchers with the projector

3D connections

Frame sequential 1080p 3D up to 120Hz and WUXGA 3D at 100Hz

Dual Pipe 1080p, WUXGA and WQXGA+ 3D sources at up to 100 and 120Hz

3D Sync

Control connections

LAN connection examples

RS232 connection example

Using the menus

Opening the Menu

Opening a submenu

Exiting menus and closing the OSD

Inside a menu

Accessing sub menus

Executing commands

Editing projector settings

Using a slider to set a value

Editing numeric values

Using the projector

Main menu

Lens menu

Lens control

Lens memory

Image menu

Color menu

Color space

Color mode

ColorMax

Manual color matching

Color matching parameters explained

Color temperature

Gains and lifts

Geometry menu

Aspect ratio

Theaterscope setting

Digital zoom

Overscan

Blanking

Keystone

Keystone example