Page 1
Rev C April 2011
TITAN sx+ 3D, Dual 3D,
TITAN sx+ 3D, Dual 3D Ultra Contrast
High Brightness Digital Video Projector
4:3 display
User Manual
109-798C
Page 2
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Page 3
Digital Projection TITAN sx+600/700. User Manual
Declaration of Conformity
Directives covered by this Declaration
2004/108/EC Electromagnetic Compatibility Directive.
2006/95/EC Low Voltage Equipment Directive.
Products covered by this Declaration
Large screen video projector type The CE mark was first applied in:
TITAN sx+ 3D January 2009
TITAN sx+ Dual 3D January 2009
TITAN sx+ 3D Ultra Contrast January 2009
TITAN sx+ Dual 3D Ultra Contrast January 2009
Basis on which Conformity is being declared
The products identified above comply with the protection requirements of the above EU directives, and the
manufacturer has applied the following standards.
EN 55022:1998 - Limits and Methods of Measurement of Radio Disturbance Characteristics of Information
Technology Equipment.
EN 55024:1998 - Limits and Methods of Measurement of Immunity Characteristics of Information Technology
Equipment.
EN 55103:1997 - Product family Standard for Audio, Video, Audio-Visual and Entertainment Lighting Control
apparatus for Professional Use.
EN 60950-1:2001 - Specification for Safety of Information Technology Equipment, including Electrical Business
equipment.
The technical documentation required to demonstrate that the products meet the requirements of the Low Voltage
directive has been compiled by the signatory below and is available for inspection by the relevant enforcement
authorities.
Signed:
Authority: D.J. Quinn, Product Development Director
Date: 16 January 2009
Attention!
The attention of the specifier, purchaser, installer, or user is drawn to special measures and limitations to use which
must be observed when these products are taken into service to maintain compliance with the above directives.
Details of these special measures are available on request, and are also contained in the product manuals.
Page 4
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Page 5
Rev C April 2011 Page v
Please read this user manual carefully before using the projector, and keep
the manual handy for future reference.
A serial number is located on the side of the projector. Record it here:
Symbols used in this guide
Warnings
ELECTRICAL WARNING: this symbol indicates that there is a danger of
electrical shock unless the instructions are closely followed.
WARNING: this symbol indicates that there is a danger of physical
injury to yourself and/or damage to the equipment unless the
instructions are closely followed.
NOTE: this symbol indicates that there is some important information that
you should read.
Trademarks
IBM is a registered trademark of International Business Machines Corporation.
Macintosh and PowerBook are registered trademarks of Apple Computer, Inc.
Other product and company names mentioned in this user’s manual may be the
trademarks of their respective holders.
Product revision
Because we at Digital Projection continually strive to improve our products, we
may change specifications and designs, and add new features without prior
notice. Projectors built prior to this revision of the User Manual may therefore not
include all the features described.
Manual revision
Date Description Revision
August 2009 Rev A
September 2010 Mains cables corrected. Lamp and Filter
maintenance removed. Section 4 extensively
updated.
Rev B
April 2011 Various updates Rev C
•
•
•
•
Important Information
Page 6
Page vi Rev C April 2011
Important Information Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
General precautions
Do not open the cabinet. There are no user serviceable parts inside.
Use only the power cable provided.
Ensure that the power outlet includes a Ground connection, as this
equipment MUST be earthed.
Take care to prevent small objects such as paper or wire from falling
into the projector. If this does happen, switch off immediately, and have
the objects removed by authorised service personnel.
Do not expose the projector to rain or moisture, and do not place any
liquids on top of the projector.
Unplug before cleaning, and use a damp, not wet, cloth.
Do not touch the power plug with wet hands.
Do not touch the power plug during a thunder storm.
Handle the power cable carefully and avoid sharp bends. Do not use a
damaged power cable.
The lamp and filters in this projector should be changed ONLY by
authorised and qualified service personnel.
Do not use the lamp for more than 2000 hours, as this may cause
serious lamp failure, damage the lamp module and cause extra cost on
replacement.
HID lamps produce high intensity light. Do not look directly at the light
coming from the lamp housing, or the lens, or allow items such as
magnifying lenses to be placed in the light path. This could result in
serious eye damage.
Do not touch the ventilation outlets, as they will become hot in use.
Do not cover or obstruct the ventilation outlets or inlets.
Do not cover the lens whilst the projector is switched on. This could
cause a fire
Always allow the projector to cool for 5 minutes before disconnecting
the power, moving the projector or changing the lamp.
Never use strong detergents or solvents such as alcohol or thinners to
clean the projector and lens.
Notes
Page 7
Rev C April 2011 Page vii
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual Important Information
Installation precautions
Connect the LAN cable only to a computer LAN connection. Other
similar connectors may have a dangerously high voltage source.
The projector must be installed only by suitably qualified personnel, in
accordance with local building codes.
The projector should be installed as close to the power outlet as
possible.
The power connection should be easily accessible, so that it can be
disconnected in an emergency.
Ensure that there is at least 30cm (12in) of space between the
ventilation outlets and any wall, and 10cm (4in) on all other sides.
Do not install the projector close to anything that might be affected by
its operational heat, for instance, polystyrene ceiling tiles, curtains etc.
The projector weighs approximately 31 kg (68 lbs). Use safe handling
techniques when lifting the projector.
When stacking projectors, the stack MUST be vertical, to ensure that
the stresses are distributed to all frame couplings.
Before installation, make sure that the surface, ceiling or rigging that is
to support the projector is capable of supporting the combined weight
of the projector and lens (see specification for exact weights).
Separate backup safety chains or wires should always be used for each
projector.
Do not place heavy objects on top of the projector chassis. Only the
chassis corners and the rigging frame are capable of withstanding the
weight of another projector.
Do not stack more than 3 projectors.
Do not drop or knock the projector.
The lens release lever should always be set to the locked position to
prevent the lens from falling out.
Each time a new lens is fitted to the projector, the calibration procedure
must be carried out. See Setup menu, in Section 4. Controlling the
projector.
Place the projector in a dry area away from sources of dust, moisture,
steam, smoke, sunlight or heat.
Do not tilt the projector more than ±10° in either direction when in use,
as this may cause serious lamp failure, damage the lamp module and
cause extra cost on replacement.
Notes
It may be possible to use
the projector in other
orientations, depending on
lamp configuration. For more
information, contact Digital
Projection.
±10°
±10°
Page 8
Page viii Rev C April 2011
Important Information Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Notes
Operation and configuration precautions
Do not make changes to the networking configuration unless you
understand what you are doing, or have taken advice from your
Network Manager. If you make a mistake, it is possible that you will lose
contact with the projector. Always double-check your settings before
pressing the APPLY button. Always keep a written note of the original
settings, and any changes you have made.
Software update should NOT be carried out except by, or with the
supervision of, Digital Projection Service personnel.
Compliance with international standards
Noise
GSGV Acoustic Noise Information Ordinance
The sound pressure level is less than 70 dB (A) according to ISO 3744 or ISO 7779.
RF Interference
FCC
The Federal Communications Commission does not allow any modifications or
changes to the unit EXCEPT those specified by Digital Projection in this manual.
Failure to comply with this government regulation could void your right to operate
this equipment.
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant with Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area may cause harmful interference, in
which case the user will be responsible for correcting any interference.
This equipment contains an FCC approved RF transmitter module with FCC ID:
R68WIPORT.
European Waste Electrical and Electronic Equipment
(WEEE) Directive
Digital Projection Ltd is fully committed to minimising Waste Electrical and
Electronic Equipment. Our products are designed with reuse, recycling
and recovery of all components in mind. To this end, at end of life, your
projector may be returned to Digital Projection Ltd or its agent so that the
environmental impact can be minimised.
Page 9
Rev C April 2011 Page ix
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual Important Information
Digital Projection Contact details
Digital Projection Limited,
Greenside Way, Middleton, Manchester M24 1XX, UK.
Registered in England No. 2207264, Registered Office: as above
Tel +44 (0) 161 947 3300
Fax +44 (0) 161 684 7674
Email enquiries@digitalprojection.co.uk, service@digitalprojection.co.uk
Web Site www.digitalprojection.co.uk
Digital Projection Inc.
55 Chastain Road, Suite 115, Kennesaw, GA 30144. USA
Tel (USA) 770 420 1350
Fax (USA) 770 420 1360
Email powerinfo@digitalprojection.com
Web Site www.digitalprojection.com
Notes
Page 10
Page x Rev C April 2011
Important Information Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Page 11
Rev C April 2011 Page xi
continued
Titan sx+ 3D, Dual 3D,
3D Ultra Contrast, Dual 3D Ultra Contrast
Contents
Declaration of Conformity ...................................................................................................................iii
Important Information
Symbols used in this guide ..................................................................................................................v
Warnings ..............................................................................................................................................v
Trademarks ..........................................................................................................................................v
Product revision ......................................................................................................................................v
Manual revision .......................................................................................................................................v
General precautions ..............................................................................................................................vi
Installation precautions ......................................................................................................................vii
Operation and configuration precautions .....................................................................................viii
Compliance with international standards ...................................................................................... viii
Noise ................................................................................................................................................viii
RF Interference..................................................................................................................................viii
European Waste Electrical and Electronic Equipment (WEEE) Directive .................................................viii
Digital Projection Contact details ......................................................................................................ix
1. Introduction
What’s in the box? .............................................................................................................................. 1.2
Key features of the projector ........................................................................................................... 1.3
Getting to know the projector .......................................................................................................... 1.4
Front panel, – lens and power ............................................................................................................ 1.4
Rear panel ....................................................................................................................................... 1.4
Side panel – connection and control ................................................................................................... 1.5
2. Installation
Screen requirements ......................................................................................................................... 2.2
Aspect ratio ...................................................................................................................................... 2.2
Positioning the screen and projector ................................................................................................... 2.5
Choosing a lens .................................................................................................................................. 2.6
Choosing a lens using the lens charts ................................................................................................. 2.7
Choosing a lens by calculation ........................................................................................................... 2.8
Useful lens calculations .................................................................................................................... 2.9
Fitting the lens ................................................................................................................................... 2.10
Fixed lens clamp ..............................................................................................................................2.11
Page 12
Page xii Rev C April 2011
Table of Contents Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
continued
Shifting the image............................................................................................................................. 2.12
Mounting the projector .................................................................................................................... 2.13
Chassis adjustment ......................................................................................................................... 2.13
Fitting the optional rigging frame....................................................................................................... 2.13
Stacking projectors .......................................................................................................................... 2.15
Connecting the projector ................................................................................................................ 2.16
Signal Inputs .................................................................................................................................. 2.16
Input format, DVI input 3 .................................................................................................................. 2.17
Input formats, DVI input 8 ................................................................................................................ 2.17
DVI Input connection examples ........................................................................................................ 2.18
3D connection examples ................................................................................................................. 2.19
Control connection examples ........................................................................................................... 2.20
Power connection ........................................................................................................................... 2.21
3. Getting Started
Switching the projector on ............................................................................................................... 3.2
Selecting an input or test pattern ................................................................................................... 3.2
Input ................................................................................................................................................ 3.2
Test pattern ...................................................................................................................................... 3.2
Adjusting the lens............................................................................................................................... 3.3
Focus .............................................................................................................................................. 3.3
Zoom ............................................................................................................................................... 3.3
Shift ................................................................................................................................................. 3.3
Adjusting the projected image ........................................................................................................ 3.4
Picture settings ................................................................................................................................. 3.4
Geometry settings ............................................................................................................................. 3.4
Switching the projector off ............................................................................................................... 3.4
4. Controlling the projector
Overview ............................................................................................................................................... 4.5
Controlling the projector..................................................................................................................... 4.5
Input modes and settings ................................................................................................................... 4.6
Special considerations when using Input 8 .......................................................................................... 4.8
Indicators .............................................................................................................................................. 4.9
Input status indicators ....................................................................................................................... 4.9
The control panel .............................................................................................................................. 4.10
Keypad layout................................................................................................................................. 4.10
Projector status indicators ................................................................................................................ 4.10
The remote control ............................................................................................................................4.11
Layout ............................................................................................................................................4.11
Timeout ...........................................................................................................................................4.11
Page 13
Rev C April 2011 Page xiii
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual Table of Contents
continued
Using the control keys .................................................................................................................... 4.12
Power ............................................................................................................................................ 4.12
Shutter ........................................................................................................................................... 4.12
On-Screen-Display .......................................................................................................................... 4.12
Focus ............................................................................................................................................ 4.12
Zoom ............................................................................................................................................. 4.12
Shift ............................................................................................................................................... 4.12
Calibrate Focus .............................................................................................................................. 4.13
Calibrate Zoom ............................................................................................................................... 4.13
Auto-detect input mode ................................................................................................................... 4.13
Source information .......................................................................................................................... 4.13
Input .............................................................................................................................................. 4.13
Input Presets .................................................................................................................................. 4.14
Red, Green and Blue....................................................................................................................... 4.14
Test pattern .................................................................................................................................... 4.14
Picture settings ............................................................................................................................... 4.15
Geometry settings ........................................................................................................................... 4.15
Magnify and pan ............................................................................................................................. 4.16
On-screen-display size .................................................................................................................... 4.16
Remote control address................................................................................................................... 4.16
Remote control backlight ................................................................................................................. 4.16
Using the menus ............................................................................................................................... 4.17
Navigating menus and submenus ..................................................................................................... 4.17
Menu controls ................................................................................................................................. 4.19
Input menu .........................................................................................................................................4.20
Input Source ................................................................................................................................... 4.20
Presets .......................................................................................................................................... 4.21
Picture menu ...................................................................................................................................... 4.24
Brightness ...................................................................................................................................... 4.24
Contrast ......................................................................................................................................... 4.24
Saturation ...................................................................................................................................... 4.24
Hue ............................................................................................................................................... 4.24
Gamma Correction .......................................................................................................................... 4.25
Parametric Gamma ......................................................................................................................... 4.25
Phase ............................................................................................................................................ 4.25
Aspect Ratio ................................................................................................................................... 4.26
Sharpness ...................................................................................................................................... 4.26
Page 14
Page xiv Rev C April 2011
Table of Contents Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
continued
Geometry menu ................................................................................................................................. 4.27
Horizontal Position .......................................................................................................................... 4.27
Vertical Position .............................................................................................................................. 4.27
Aspect Ratio ................................................................................................................................... 4.27
User Horizontal Aspect Ratio ........................................................................................................... 4.28
User Vertical Aspect Ratio ............................................................................................................... 4.28
Keystone ........................................................................................................................................ 4.28
Phase ............................................................................................................................................ 4.28
Resolution ...................................................................................................................................... 4.29
Blanking ......................................................................................................................................... 4.30
Colour menu ......................................................................................................................................4.31
Colour Mode................................................................................................................................... 4.32
Colour Temperature ........................................................................................................................4.32
RGB Lift ......................................................................................................................................... 4.32
RGB Gain ...................................................................................................................................... 4.32
Component Type ............................................................................................................................ 4.32
Trim ............................................................................................................................................... 4.33
Setup menu ........................................................................................................................................ 4.34
Projector Setup ............................................................................................................................... 4.35
Keystone ........................................................................................................................................ 4.36
Test Patterns .................................................................................................................................. 4.37
FastFrame ..................................................................................................................................... 4.38
Edge Blend .................................................................................................................................... 4.39
Black Level Uplift ............................................................................................................................ 4.41
Global Colourimetry ........................................................................................................................ 4.43
Lamp Setup .................................................................................................................................... 4.45
On Screen Display .......................................................................................................................... 4.47
Password ....................................................................................................................................... 4.48
Communication Setup ..................................................................................................................... 4.49
Network Setup ................................................................................................................................ 4.50
3D Setup ........................................................................................................................................ 4.54
Lens Setup ..................................................................................................................................... 4.59
Restore Defaults ............................................................................................................................. 4.60
Information menu .............................................................................................................................4.61
Projector Information ....................................................................................................................... 4.61
Source Information .......................................................................................................................... 4.61
Digital Projection Information ........................................................................................................... 4.62
Page 15
Rev C April 2011 Page xv
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual Table of Contents
5. Userware
Introduction .......................................................................................................................................... 5.4
Applet version................................................................................................................................... 5.4
Standalone version ........................................................................................................................... 5.5
Show page ............................................................................................................................................ 5.6
On / Off ............................................................................................................................................ 5.6
Shutter Open / Closed ....................................................................................................................... 5.6
Freeze / Un-Freeze ........................................................................................................................... 5.6
Picture sliders ................................................................................................................................... 5.6
Input Presets .................................................................................................................................... 5.7
Orientation ....................................................................................................................................... 5.8
Input ................................................................................................................................................ 5.8
Test Pattern ...................................................................................................................................... 5.8
Aspect Ratio ..................................................................................................................................... 5.8
Lens page ............................................................................................................................................. 5.9
Lens controls .................................................................................................................................... 5.9
Shutter Open / Closed ....................................................................................................................... 5.9
Calibrate Focus ................................................................................................................................ 5.9
Calibrate Zoom ................................................................................................................................. 5.9
Edge Blend page ............................................................................................................................... 5.10
Markers On / Off ............................................................................................................................. 5.10
Active Edges .................................................................................................................................. 5.10
Input 8 DVI 3D Resolution ............................................................................................................... 5.10
Overlap Width................................................................................................................................. 5.10
Black Level Uplift page .....................................................................................................................5.11
x2, x4 Region Uplift ..........................................................................................................................5.11
Non-Addressable Border ..................................................................................................................5.11
Back to Edge Blend..........................................................................................................................5.11
Image page ......................................................................................................................................... 5.12
Colour Space ................................................................................................................................. 5.12
Component .................................................................................................................................... 5.12
Phase slider ................................................................................................................................... 5.12
Gamma .......................................................................................................................................... 5.12
Parametric slider ............................................................................................................................. 5.12
Convergence controls ..................................................................................................................... 5.13
Horizontal Convergence .................................................................................................................. 5.13
Vertical Convergence ...................................................................................................................... 5.13
Close ............................................................................................................................................. 5.13
continued
Page 16
Page xvi Rev C April 2011
Table of Contents Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Screen page ....................................................................................................................................... 5.14
Blanking On / Off ............................................................................................................................ 5.14
Blanking adjust ............................................................................................................................... 5.14
Keystone adjust .............................................................................................................................. 5.14
Position adjust ................................................................................................................................ 5.14
MCGD page ........................................................................................................................................ 5.15
The MCGD measurement procedure ................................................................................................ 5.15
MCGD edit boxes ........................................................................................................................... 5.16
Write to Projector ............................................................................................................................ 5.16
Read from Projector ........................................................................................................................ 5.16
Save File ........................................................................................................................................ 5.16
Open File ....................................................................................................................................... 5.16
TCGD page ......................................................................................................................................... 5.17
TCGD values .................................................................................................................................. 5.17
Update Graph ................................................................................................................................. 5.18
Save File ........................................................................................................................................ 5.18
Open File ....................................................................................................................................... 5.18
Write User 1, User 2 ........................................................................................................................ 5.18
Read User 1, User 2 ....................................................................................................................... 5.18
3D page ............................................................................................................................................... 5.19
3D Enable ...................................................................................................................................... 5.19
3D Input ......................................................................................................................................... 5.19
Dark Time ...................................................................................................................................... 5.19
Sync Delay ..................................................................................................................................... 5.19
Frame Dominance .......................................................................................................................... 5.19
3D Sync Output Polarity .................................................................................................................. 5.19
Frame Rate Multiplier ...................................................................................................................... 5.20
3D Format ...................................................................................................................................... 5.20
Create 3D Preset ............................................................................................................................ 5.20
Recall 3D Preset ............................................................................................................................. 5.20
Global Colour page ..........................................................................................................................5.21
Global Colour Mode ........................................................................................................................ 5.21
Modal Colour page ........................................................................................................................... 5.22
Modal Colour Mode ......................................................................................................................... 5.22
Lift and Gain sliders ........................................................................................................................ 5.23
Temperature slider .......................................................................................................................... 5.23
Information page ............................................................................................................................... 5.24
Projector Information ....................................................................................................................... 5.24
Digital Projection ............................................................................................................................. 5.24
continued
Page 17
Rev C April 2011 Page xvii
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual Table of Contents
FastFrame page ................................................................................................................................5.25
FastFrame Enable .......................................................................................................................... 5.25
Dark Time ...................................................................................................................................... 5.25
System page ...................................................................................................................................... 5.26
OSD .............................................................................................................................................. 5.26
Backlight ........................................................................................................................................ 5.26
DMD controls ................................................................................................................................. 5.26
Lamp mode .................................................................................................................................... 5.26
Lamp Power slider .......................................................................................................................... 5.26
Connect page ..................................................................................................................................... 5.27
Refresh .......................................................................................................................................... 5.27
Connect ......................................................................................................................................... 5.27
Disconnect ..................................................................................................................................... 5.27
6. Maintenance
Changing the lamp module .............................................................................................................. 6.2
Changing the air filters ...................................................................................................................... 6.2
Cleaning ................................................................................................................................................ 6.3
Projector .......................................................................................................................................... 6.3
Lens ................................................................................................................................................ 6.3
7. Appendix
Troubleshooting .................................................................................................................................. 7.2
Specifications ...................................................................................................................................... 7.4
Part numbers .................................................................................................................................... 7.4
Optical ............................................................................................................................................. 7.4
Electrical .......................................................................................................................................... 7.5
Physical ........................................................................................................................................... 7.5
Lens Data ........................................................................................................................................ 7.6
Dimensions .......................................................................................................................................... 7.8
Input modes supported by inputs 1-7 ............................................................................................ 7.9
Input connections ............................................................................................................................. 7.10
1. RGB1 input ................................................................................................................................. 7.10
2. RGB2 input ................................................................................................................................. 7.10
3. DVI-D Single input ........................................................................................................................7.11
4. SDI input .................................................................................................................................... 7.12
5. Composite video input ................................................................................................................. 7.12
6. S-Video input .............................................................................................................................. 7.12
7. Component video input ................................................................................................................ 7.12
8. DVI-D Single/Dual/Twin input ....................................................................................................... 7.13
Page 18
Page xviii Rev C April 2011
Table of Contents Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Control connections ........................................................................................................................7.14
Wired Remote control connection ..................................................................................................... 7.14
LAN connection .............................................................................................................................. 7.14
3D sync ......................................................................................................................................... 7.15
Serial control input .......................................................................................................................... 7.15
Remote communications protocol ............................................................................................... 7.16
Introduction .................................................................................................................................... 7.16
Message Structure .......................................................................................................................... 7.16
Operation Command examples ........................................................................................................ 7.19
Quick Reference chart ..................................................................................................................... 7.24
Page 19
Rev C April 2011 Page 1.1
1. Introduction
Contents
What’s in the box? .............................................................................................................................. 1.2
Key features of the projector ........................................................................................................... 1.3
Getting to know the projector .......................................................................................................... 1.4
Front panel, – lens and power ............................................................................................................ 1.4
Rear panel ....................................................................................................................................... 1.4
Side panel – connection and control ................................................................................................... 1.5
Page 20
Page 1.2 Rev C April 2011
1. Introduction Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
What’s in the box?
Make sure your box contains everything listed. If any pieces are missing, contact
your dealer.
You should save the original box and packing materials, in case you ever need
to ship your Projector.
•
•
Notes
Lenses are optional. Order
lenses from your Digital
Projection dealer.
For more detailed information
about lenses, see Choosing a
lens, in section 2. Installation.
Only one power cable -
dependent on the destination
territory - will be supplied with
the projector.
Projector
(sx+ 3D: 109-340
sx+ 3D Ultra Contrast: 109-341
sx+ Dual 3D: 109-334
sx+ Dual 3D Ultra Contrast: 109-335)
Important Information
(108-467)
User manual on CD
(105-923)
Remote control
(105-023)
4x AAA batteries
(105-922)
Power cable 13A
North America
(102-165)
Power cable 10A
Europe
(102-163)
Power cable 10A
United Kingdom
(102-180)
3D Sync cable
(109-697)
Page 21
Rev C April 2011 Page 1.3
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 1. Introduction
Notes
Key features of the projector
Congratulations on your purchase of the Digital Projection Titan sx+-3D/FastFrame
projector.
Digital Projection International, Texas Instruments’ first DLP™ partner and the
original innovator of the 3-chip DLP™ projector, proudly introduces the Titan sx+.
Titan 3D projectors are the perfect imaging solution for vital immersive applications,
including military, scientific and medical applications, product engineering,
commercial cinema and theme parks. In addition, DP’s new FastFrame™
technology is a revolutionary combination of hardware and firmware that reduces
the artifact and image blur associated with rapidly moving displayed content.
The Titan sx+ harnesses the power of the Texas Instruments’ 1400 x 1050 pixel
DMD’s™. Along side the LIGHTNING and HIGHlite Pro, the Titan sx+ is to set new
standards for Staging and destined to be the first choice of professionals who stage
prestigious events such as the Grammy® Awards and the Oscars®. With a contrast
of up to 4000:1 and awe-inspiring brightness of up to 9000 lumens, the Titan sx+
is unmatched for applications as diverse as world class staged events, commercial
entertainment, major outdoor venues, large-scale simulation, gaming and houses of
worship.
Key Features
High resolution, large venue 3D projector
Applications: Large Screen; Fixed install and Rental
1400 x 1050 resolution
Precision mechanical design ensuring maximum amount of light from lamp
housing reaches optics, without any operator adjustment
Single: 600W single phase, 100-240VAC ±10%
Dual: 1000W single phase, 100-240VAC ±10%
Compact size, light weight - 31 kg (68 lbs)
Intelligent motorised lens mount
Optional Rigging frame with Quick-lock stack system
Ruggedised robust metal case
Floating chassis - 3 point pitch & roll adjustment for accurate alignment
LAN & RS232 connection for network operation
Eight selectable Digital and Analogue Video inputs for display of the latest as
well as legacy video standards.
DVI, SD and HD SDI, RGBHV, Component, S-Video, Composite all as standard
Wi-fi connection wireless remote control
IR/cable remote control for easy setup
LAN operation using control codes or Integrated Userware
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Page 22
Page 1.4 Rev C April 2011
1. Introduction Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Notes
For more detailed information
about lenses, see
section 2. Installation
Getting to know the projector
Front panel, – lens and power
Rear panel
Rear Infra-red window
(remote control)
Power
connection
Lens
Air inlet -
around lens
Front Infra-red window
(remote control)
Air inlet
Air outlet
duct
Page 23
Rev C April 2011 Page 1.5
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 1. Introduction
Notes
For information about how
to connect the projector, see
Connecting the projector in
section 2. Installation, and
Connections in section 7.
Appendix.
For information about how
to use the control panel, see
section 4. Controlling the
projector.
For information about how to
mount and stack projectors, see
section 2. Installation.
Side panel – connection and control
Front input
connections
Control
connections
Control panel
Adjustable
foot
Rear input
connections
Page 24
Page 1.6 Rev C April 2011
1. Introduction Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Page 25
Rev C April 2011 Page 2.1
2. Installation
Contents
Screen requirements ......................................................................................................................... 2.2
Aspect ratio ...................................................................................................................................... 2.2
Fitting the image to the DMD ............................................................................................................. 2.2
Images displayed full width ............................................................................................................... 2.2
Images displayed full height .............................................................................................................. 2.2
Diagonal screen sizes ...................................................................................................................... 2.3
Fitting the image to the screen ........................................................................................................... 2.4
Positioning the screen and projector ................................................................................................... 2.5
Choosing a lens .................................................................................................................................. 2.6
Choosing a lens using the lens charts ................................................................................................. 2.7
Example ....................................................................................................................................... 2.7
Choosing a lens by calculation ........................................................................................................... 2.8
Example ....................................................................................................................................... 2.8
Useful lens calculations .................................................................................................................... 2.9
Lens extension ............................................................................................................................... 2.9
Fitting the lens ................................................................................................................................... 2.10
Fixed lens clamp ..............................................................................................................................2.11
Shifting the image............................................................................................................................. 2.12
Mounting the projector .................................................................................................................... 2.13
Chassis adjustment ......................................................................................................................... 2.13
Fitting the optional rigging frame....................................................................................................... 2.13
Adjusting the rigging frame .............................................................................................................. 2.14
Stacking projectors .......................................................................................................................... 2.15
Connecting the projector ................................................................................................................ 2.16
Signal Inputs .................................................................................................................................. 2.16
Input format, DVI input 3 .................................................................................................................. 2.17
Input formats, DVI input 8 ................................................................................................................ 2.17
DVI Input connection examples ........................................................................................................ 2.18
Input and processing architecture ..................................................................................................... 2.18
EDID handshaking on the DVI and RGB2 inputs ................................................................................. 2.18
3D connection examples ................................................................................................................. 2.19
3D sources up to 60Hz, requiring frame doubling and left/right interleaving ................................................2.19
3D sources up to 120Hz, not requiring frame doubling ........................................................................... 2.19
Control connection examples ........................................................................................................... 2.20
LAN connection ............................................................................................................................ 2.20
RS232 connection ......................................................................................................................... 2.20
Power connection ........................................................................................................................... 2.21
Page 26
Page 2.2 Rev C April 2011
2. Installation Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Screen requirements
Aspect ratio
Fitting the image to the DMD
If the source image supplied to the projector is smaller than 1400 x 1050 pixels,
then the image will not fill the DMD. The following example shows how a number
of common formats may be displayed.
Images displayed full width
Images displayed full height
Notes
The images are shown here
scaled automatically by the
projector.
The image may be scaled
differently if the Aspect Ratio is
set differently in the Picture or
Geometry menus.
full height = 1050 pixels
2.35:1(Scope)
= 596 pixels
1.85:1
= 757 pixels
16:9 = 1.78:1
= 787 pixels
1.66:1 (Vista)
= 843 pixels
1.6:1
= 875 pixels
full width = 1400 pixels
4:3 = 1.33:1 (native) = 1400 pixels
Page 27
Rev C April 2011 Page 2.3
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 2. Installation
Diagonal screen sizes
Screen sizes are sometimes specified by their diagonal size (D) in inches. When
dealing with large screens and projection distances at different aspect ratios, it is
more convenient to measure screen width (W) and height (H).
The example calculations below show how to convert diagonal sizes in inches into
width and height, at various aspect ratios.
2.35:1 (Scope)
W
= D x 0.92in (D x .023m) H = D x 0.39in (D x .01m)
1.85:1
W = D x 0.88in (D x .022m) H = D x 0.47in (D x .012m)
16:9 = 1.78:1
W = D x 0.87in (D x .022m) H = D x 0.49in (D x .0125m)
1.66:1 (Vista)
W = D x 0.86in (D x .022m) H = D x 0.52in (D x .013m)
16:10 = 1.6:1
W = D x 0.85in (D x .022m) H = D x 0.53in (D x .014m)
4:3 = 1.33:1 (native aspect ratio
W = D x 0.8in (D x .02m) H = D x 0.6in (D x .015m)
Notes
D = diagonal (inches)
W = width
H = height
Page 28
Page 2.4 Rev C April 2011
2. Installation Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Fitting the image to the screen
It is important that your screen is of sufficient height and width to display images at
all the aspect ratios you are planning to use.
Use the conversion chart, or the sample calculations below to check that you are
able to display the full image on your screen. If you have insufficient height or width,
you will have to reduce the overall image size in order to display the full image on
your screen.
Notes
2.35:1 (Scope)
W = H x 2.35 H = W x 0.426
1.85:1
W
= H x 1.85 H = W x 0.54
16:9 = 1.78:1
W
= H x 1.78 H = W x 0.56
1.66:1 (Vista)
W
= H x 1.66 H = W x 0.6
16:10 = 1.6:1
W
= H x 1.6 H = W x 0.625
4:3 = 1.33:1 (native aspect ratio)
W
= H x 1.33 H = W x 0.75
1 2 3 4 5 6 7 8 9 10
Screen width
Screen height
4:3
16:9
2.35:1
Aspect ratio
10
9
8
7
6
5
4
3
2
1
1.85:1
1.66:1
16:10
Page 29
Rev C April 2011 Page 2.5
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 2. Installation
Positioning the screen and projector
For optimum viewing, the screen should be a flat surface perpendicular to the floor.
The bottom of the screen should be 1.2m (4 feet) above the floor and the front row
of the audience should not have to look up more than 30° to see the top of the
screen.
The distance between the front row of the audience and the screen should be at
least twice the screen height and the distance between the back row and the screen
should be a maximum of 8 times the screen height. The screen viewing area should
be within a 60° range from the face of the screen.
Notes
The projector should be
installed as close to the
power outlet as possible.
The power connection should
be easily accessible, so that
it can be disconnected in an
emergency.
Ensure that there is at least
30cm (12in) of space between
the ventilation outlets and
any wall, and 10cm (4in) on
all other sides.
Do not install the projector
close to anything that
might be affected by its
operational heat, for instance,
polystyrene ceiling tiles,
curtains etc.
The image can be flipped for
rear projection (see section
4. Using the menus, Image
menu) and displayed without
the need for extra mirrors or
equipment.
However, you must ensure
that there is sufficient distance
behind the screen for the
projector to be correctly located.
Rear installation is generally
more complicated and advice
should be sought from your
local dealer before attempting it.
Page 30
Page 2.6 Rev C April 2011
2. Installation Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Notes
The High Brightness lenses are
recommended for the standard
models, for maximum light
output.
The High Contrast lenses are
recommended for the Ultra
Contrast models, for maximum
contrast.
Each time a new lens is
fitted to the projector,
the calibration procedure
must be carried out. See
Setup menu, in Section 4.
Controlling the projector.
For more information about
Throw ratio factor (TRF), see
Useful lens calculations, later
in this section.
Choosing a lens
A number of lenses are available for use with the projector. Which lens you choose
will depend on the screen size, image aspect ratio, projection distance and light
output.
The lenses available and their part numbers are listed below:
High Brightness High Contrast
0.73 : 1 fixed lens 105-607 107-195
1.2 : 1 fixed lens (3 - 15m) 105-608 105-608
1.2 : 1 fixed lens (1.2 - 2m) 105-609 105-609
1.26 - 1.61 : 1 zoom lens 109 236 109-359
1.5 - 2.02 : 1 zoom lens 105-610 107-196
2.02 - 2.77 : 1 zoom lens 105-611 107-197
2.77 - 4.51 : 1 zoom lens 105-612 107-198
4.51 - 7.53 : 1 zoom lens 105-613 107-199
7.5 - 11.2 : 1 zoom lens 109-235 109-358
If you are simply connecting the output of a camera or computer directly to the
projector, then the image size (in pixels) may well be fixed. If, however, you are
using commercially available image processing equipment, such as the Digital
Projection VIP2000, you may be able to resize the image to fit the DMD.
If the image does not fill the full width of the DMD, this effectively increases the
throw ratio of the lens. This can be corrected for by applying a Throw ratio factor.
Method one: using the lens chart
For the screen sizes listed below, use the chart on the following pages, to choose
the most suitable lens.
any full width image, including:
4:3 = 1.33:1 1400 x 1050 pixels (native resolution)
16:10 = 1.6:1 1400 x 875 pixels
1.66:1 (Vista) 1400 x 843 pixels
16:9 = 1.78:1 1400 x 788 pixels
1.85:1 1400 x 757 pixels
2.35:1 (Scope) 1400 x 596 pixels
Method two: by calculation
See the calculations, on the page immediately following the lens chart.
Page 31
Rev C April 2011 Page 2.7
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 2. Installation
Notes
Choosing a lens using the lens charts
Use the chart below to choose which lens best suits your application.
Example
For a screen width of 12m at a distance of 35m, the 2.77 - 4.51: 1 zoom lens
would be best suited.
For the same screen size at a distance of 60m, the 4.51 - 7.53: 1 zoom lens
would be best suited.
if you need to be more precise, then use the calculations on the page immediately
following the lens chart.
•
•
feet
metres
Screen width
10 20 30 40 50 60 70 80 metres
33 66 98 131 164 197 230 262 feet
66 20
49 15
33 10
16 5
Throw distance
1.2 : 1 fixed lens
(1.2 - 2m)
105-609
105-609
1.5 - 2.02 : 1
zoom lens
105-610
107-196
2.02 - 2.77 : 1
zoom lens
105-611
107-197
4.51 - 7.53 : 1
zoom lens
105-613
107-199
0.73 : 1 fixed lens
105-607
107-195
2.77 - 4.51 : 1
zoom lens
105-612
107-198
1.2 : 1 fixed lens
(3 - 15m)
105-608
105-608
1.26 - 1.61 : 1
zoom lens
109-236
109-359
7.5 - 11.2 : 1
zoom lens
109-235
109-358
Page 32
Page 2.8 Rev C April 2011
2. Installation Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Notes
The Throw ratio for a particular
lens is fixed, and assumes that
the image fills the width of the
DMD.
For images that do not fill the
width of the DMD, the Throw
ratio is effectively increased. To
correct for this, a Throw Ratio
Factor (TRF) is used.
Choosing a lens by calculation
For any screen size not listed above, or if you need to be more precise, then use the
calculations below.
Identify actual width of the image in pixels.
Calculate the Throw Ratio Factor: TRF = DMD width (1400)
Image width in pixels
Identify the screen width required.
Identify the throw distance required.
Throw distance calculations are based on the distance from the outer end of the
lens, which will vary from lens to lens. Once a lens has been chosen, the figures
can be checked using the lens extension values given on the next page.
Calculate the throw ratio required. Throw ratio = Throw distance
Screen width x TRF
Choose a lens with the required throw ratio from the list at the bottom of the
page.
Check from the list that the lens chosen will work at the throw distance required.
Example
An image, 1024 x 768 pixels, screen width 6.5m, throw distance 18m from the
outer end of the lens.
Throw Ratio Factor (TRF) = 1400 = 1.37
1024
Throw ratio required = 18 = 2.02
6.5 x 1.37
Choose the 2.0 - 2.77 zoom lens.
•
•
•
•
•
•
•
•
•
•
High Brightness High Contrast Throw distance range
0.73 : 1 fixed lens 105-607 107-195 1.1 - 3.2m (3.6 - 10.5ft)
1.2 : 1 fixed lens (3 - 15m) 105-608 105-608 3 - 15m (9.8 - 49.2ft)
1.2 : 1 fixed lens (1.2 - 2m) 105-609 105-609 1.2 - 2m (3.9 - 6.6ft)
1.26 - 1.61 : 1 zoom lens 109 236 109-359 3 - 15m (9.8 - 49.2ft)
1.5 - 2.02 : 1 zoom lens 105-610 107-196 4 - 24m (13.1 - 78.7ft)
2.02 - 2.77 : 1 zoom lens 105-611 107-197 4 - 24m (13.1 - 78.7ft)
2.77 - 4.51 : 1 zoom lens 105-612 107-198 9.1 - 45m (29.9 - 147.6ft)
4.51 - 7.53 : 1 zoom lens 105-613 107-199 12 - 80m (39.4 - 262.5ft)
7.5 - 11.2 : 1 zoom lens 109-235 109-358 12 - 80m (39.4 - 262.5ft)
Page 33
Rev C April 2011 Page 2.9
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 2. Installation
Notes
The Throw ratio for a particular
lens is fixed, but assumes that
the image fills the width of the
DMD.
For images that do not fill the
width of the DMD, the Throw
ratio is effectively increased. To
correct for this, a Throw Ratio
Factor (TRF) is used.
Useful lens calculations
The following lens calculations may be useful:
Throw ratio
= Throw distance
Screen width
Throw ratio factor (TRF) = DMD width in pixels = 1400
image width in pixels image width in pixels
Therefore:
Screen width = Throw distance
Throw ratio x TRF
Throw distance = Screen width x Throw ratio x TRF
Lens extension
The throw distance calculated above is to the outer end of the lens. For each lens,
the nominal distance between the front of the projector and the outer end of the lens
(lens extension) will be as listed below.
High Brightness/ Contrast Lens extension (±2%)
0.73 : 1 fixed lens 105-607 107-195 204 mm (8.0 in)
1.2 : 1 (3 - 15m) fixed lens 105-608 105-608 268 mm (10.6 in)
1.2 : 1 (1.2 - 2.0m) fixed lens 105-609 105-609 268 mm (10.6 in)
1.26 - 1.61 : 1 zoom lens 109 236 109-359 226 mm (8.9 in)
1.5 - 2.02 : 1 zoom lens 105-610 107-196 194 mm (7.6 in)
2.02 - 2.77 : 1 zoom lens 105-611 107-197 159 mm (6.3 in)
2.77 - 4.51 : 1 zoom lens 105-612 107-198 145 mm (5.7 in)
4.51 - 7.53 : 1 zoom lens 105-613 107-199 129 mm (5.1 in)
7.5 - 11.2 : 1 zoom lens 109-235 109-358 179 mm (7.0 in)
lens extension,
measured from front
of corner post
Page 34
Page 2.10 Rev C April 2011
2. Installation Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Notes
Each time a new lens is
fitted to the projector,
the calibration procedure
must be carried out. See
Setup menu, in Section 4.
Controlling the projector.
Make sure the rear lens cap is
removed, before fitting the lens.
Be careful not to scratch
the lens surfaces. If you do
accidentally touch a lens, then
clean the surface using a lens
paper.
The lens release lever should
always be set to the locked
position, as shown on the
next page, to prevent the lens
from falling out.
Zoom drive connector
Fitting the lens
Turn the lens release lever clockwise so that it is pointing upwards, to open the
lock fully.
Remove the rear lens cap from the lens.
Insert the lens into the lens aperture, making sure that the plug on the zoom
drive mechanism lines up with the socket on the front of the projector, then push
the lens in firmly as far as it will go.
•
•
•
Lens release
lever, open
Lens release
lever, midposition
Turn the lens release lever anti-clockwise to the mid-position, as shown below.•
The lens can now be pushed in further. Push the lens in firmly as far as it will go.•
Page 35
Rev C April 2011 Page 2.11
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 2. Installation
Notes
Be careful not to scratch
the lens surfaces. If you do
accidentally touch a lens, then
clean the surface using a lens
paper.
The lens release lever should
always be set to the locked
position to prevent the lens
from falling out.
Make sure the front lens cap is
removed, before switching on
the projector.
Lens clamp kit, part number
111-256, comprises:
2 x lens clamp quadrants
4 x 20mm M3 allen screws
Turn the lens release lever anti-clockwise so that it is pointing downwards, to
close the lock fully.
•
Lens release
lever, locked
Fixed lens clamp
In addition to the lens lock, any of the fixed lenses can be permanently secured to
the projector, as follows:
Fit and lock the lens to the projector, as described above.
Fit the two clamp quadrants either side of the lens, as shown below, and secure
them with the four screws.
•
•
Lens clamp
quadrants
Page 36
Page 2.12 Rev C April 2011
2. Installation Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Notes
For more information on using
the Lens shift feature, see
section 4. Using the menus,
Using the control keys.
If the lens is to be shifted in
two directions combined, the
maximum range is somewhat
less, as can be seen below.
(zoom lens shift shown).
full horizontal or vertical shift
without distortion
combined shift
is reduced
Shifting the image
The normal position for the projector is at the centre of the screen. However, you
can set the projector above or below the centre, or to one side, and adjust the image
using the Lens shift feature to maintain a geometrically correct image.
Any single adjustment outside the ranges specified below may result in an
unacceptable level of distortion, paricularly at the corners of the image, due to
the image passing through the periphery of the lens optics.
If the lens is to be shifted in two directions combined, the maximum range
without distortion will be somewhat less, as can be seen in the diagrams to the
right.
The maximum range available with no distortion is dependent on which lens is used.
The tables below show the maximum range for images that fill the DMD. For images
which do not use the full height or width, extra shift will be possible, up to the limit of
the lens mount movement.
0.73 : 1 fixed lens
vertical
(pixels)
horizontal
(pixels)
vertical
(vs DMD height)
horizontal
(vs DMD width)
± 115 ± 98 ± 0.11H ± 0.07W
1.26 - 1.61 : 1 zoom lens
vertical
(pixels)
horizontal
(pixels)
vertical
(vs DMD height)
horizontal
(vs DMD width)
± 380 ± 280 ± 0.36H ± 0.2W
1.21 : 1 fixed lenses and all other zoom lenses
vertical
(pixels)
horizontal
(pixels)
vertical
(vs DMD height)
horizontal
(vs DMD width)
+ 525
- 420
± 280 + 0.5H
- 0.4H
± 0.2W
It is physically possible to shift the lens further than this, however there will be some
vignetting of the image beyond the ranges specified above.
•
•
Page 37
Rev C April 2011 Page 2.13
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 2. Installation
Mounting the projector
The projector is designed to be used on a flat surface, but the optional rigging frame
will allow it to be suspended from a lighting truss or rigging. The four adjustable feet
under the chassis allow the projector to be lowered onto a flat surface without any
danger of hands being trapped between the bottom frame and the surface.
Chassis adjustment
If the projector is to be operated from a flat surface such as a projector table, then
adjustment of projector level should be made by turning the four feet under the
chassis.
Fitting the optional rigging frame
Before fitting the rigging frame to the projector:
- remove the four feet;
- discard the bracket supplied for use with Titan sx+500 projectors;
- make sure that all the frame adjusters are set midway.
Secure the rigging frame to the projector using the screws supplied, as shown
in the pictures below. Three screws secure each of the adjuster brackets to its
corner post.
•
•
Fixing
screws
Adjustable
foot
Notes
BEFORE INSTALLING THE
PROjECTOR, READ ALL THE
WARNINGS BELOW AND
ALL THOSE IN IMpOrTANT
INFOrMATION AT THE
FRONT OF THIS MANUAL.
The projector weighs
approximately 31 kg (68 lbs).
Use safe handling techniques
when lifting the projector.
Make sure that the surface,
ceiling or rigging that is
to support the projector
is capable of supporting
the combined weight of
the projector and lens (see
specification for weights).
Backup safety chains or
wires should always be used.
Do not tilt the projector more
than ±10° in either direction
when in use, as this may
cause serious lamp failure,
damage the lamp module
and cause extra cost on
replacement.
It may be possible to use
the projector in other
orientations, depending on
lamp configuration. For more
information, contact Digital
Projection.
±10°
±10°
Page 38
Page 2.14 Rev C April 2011
2. Installation Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Adjusting the rigging frame
Coarse adjustment of projector level should be made by adjusting the length of
the supporting wires or chains, or by adjusting the position of the truss or rigging.
Once the initial coarse adjustment has been made, fine adjustment can be made by
turning the frame adjusters on the rigging frame:
To tilt the projector forwards and backwards (pitch adjustment),
turn either the front pair or the rear pair of vertical adjusters,
taking care to turn both adjusters by the same amount.
To tilt the projector from side to side (roll adjustment), turn either
the left pair or the right pair of vertical adjusters, taking care to
turn both adjusters by the same amount.
To rotate the projector around its vertical axis (yaw adjustment),
turn the single horizontal adjuster at the rear.
•
•
•
Vertical
adjusters
Horizontal
adjuster
Notes
Before suspending the
projector, make sure that all the
frame adjusters are set midway.
Always make adjustments in
pairs - never make a single
adjustment - otherwise
the projector frame could
become distorted.
Do not tilt the projector more
than ±10° in either direction
when in use, as this may
cause serious lamp failure,
damage the lamp module
and cause extra cost on
replacement.
It may be possible to use
the projector in other
orientations, depending on
lamp configuration. For more
information, contact Digital
Projection.
±10°
±10°
Page 39
Rev C April 2011 Page 2.15
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 2. Installation
Notes
When stacking projectors,
the stack MUST be vertical,
to ensure that the stresses
are distributed to all frame
couplings.
Make sure that the surface,
ceiling or rigging that is
to support the projector is
capable of supporting the
combined weight of all the
projectors and lenses (see
specification for weights).
Do not place heavy objects
on top of the projector
chassis. Only the chassis
corners and the rigging frame
are capable of withstanding
the weight of another
projector.
Do not try to stack more than
3 projectors.
Separate backup safety
chains or wires should
always be used for each
projector.
Stacking projectors
The rigging frame is capable of supporting the weight of up to two other projectors,
using the built-in frame couplings. The projectors can be stacked on top of each
other, or suspended below each other.
Carefully lower each projector down onto the top of the others, making sure that
all four frame couplings engage fully.
Fit a locking pin into each coupling. A ball in the end of the pin prevents the pin
from falling out – to insert or remove a locking pin, press the button on the end of
the pin to release the ball.
Align the images from the projectors, following the instructions on the previous
page and those in
section 3. Getting started, Adjusting the lens and
Adjusting the projected image.
•
•
•
Locking
pin
Frame
couplings
Page 40
Page 2.16 Rev C April 2011
2. Installation Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Notes
For more information on
selecting an input source, see
section 4. Overview, Using
the control keys, and Using
the menus.
For more information about pin
connections and control codes
see section 7. Appendix.
For more information on
input modes see section
4.
Overview.
Input 8 and 3D may not be
present on some models
Connecting the projector
Signal Inputs
The following inputs are available:
5. Composite Video
6. S-Video
7. Component
1. RGB1
2. RGB2
3. DVI
4. SDI
Rear Input
connection panel
Control
connection panel
Front Input
connection panel
8. DVI
MAIN
SUB
3D Sync
Page 41
Rev C April 2011 Page 2.17
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 2. Installation
Input format, DVI input 3
Single DVI-D
Sources upto 1400x1050 resolution; 8 bits per colour; 24- 60Hz.
Input formats, DVI input 8
Single DVI-D
Sources upto 1400x1050 resolution; 8 bits per colour; 24- 60Hz.
(Use MAIN input only)
Dual DVI-D
An input with increased frame rate.
Sources upto 1400x1050 resolution; 8 bits per colour; 24-120Hz.
(Use MAIN input only)
Twin Link (Twin Single DVI-D)
One input with increased bit depth, using both input connections:
Sources up to 1400x1050 resolution; 10 or 12 bits per colour; 24-60Hz.
(Use MAIN and SUB inputs)
Dual Pipe 3D
Two single input connections:
Sources up to 1400x1050 resolution; 10 or 12 bits per colour, at frame rates
consistent with up to 148.5 MegaPixels/sec/pipe (including blanking).
(Use MAIN for left eye video stream and SUB input for right eye video stream)
Notes
There is no scaler on input 8.
Images up to and including the
native resolution of the display
will be displayed pixel for pixel
and centred.
This enables the projector to
maximise the image bandwidth
and greyscale resolution.
Page 42
Page 2.18 Rev C April 2011
2. Installation Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
DVI Input connection examples
Input and processing architecture
EDID handshaking on the DVI and rGB2 inputs
If you are using a computer DVI card or other source that obeys the EDID
handshaking protocol, then the card or source will automatically configure itself to
suit the projector.
If not, then you should refer to the documentation supplied with the source to
manually set the resolution to 1400 x 1050 or the nearest suitable setting. Switch off
the source, connect to the projector, then switch the source back on again.
Single DVI video source
Single or Dual DVI video source
Input 3
Input 8 MAIN
Projector
Input 8 MAIN
Input 8 SUB
Twin DVI video source
Projector
Notes
Dual DVI:
high bandwidth/frame rate
Twin DVI:
increased bit depth/extended
greyscale
For important information about
how Input 8 is used, see INPUT
8 in the Notes column, and also
Section 4, Overview.
Page 43
Rev C April 2011 Page 2.19
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 2. Installation
Notes
For important information about
how Input 8 is used, see INPUT
8 in the Notes column, and also
Section 4, Overview.
Projector
3D server
Z screen or
3D glasses
Inputs 1-7
Sync
Video
Sync
out
Sync in
Projector
3D server
Z screen or
3D glasses
Input 8
Sync
Video
Sync
out
Sync in
3D connection examples
3D sources up to 60Hz, requiring frame doubling and left/right
interleaving
3D sources up to 120Hz, not requiring frame doubling
Page 44
Page 2.20 Rev C April 2011
2. Installation Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Notes
For more information about pin
connections and control codes
see section 7. Appendix.
For more information about
using a browser to control the
projector see section 4. Using
the menus.
Computer
Null-modem
cable
Control connection examples
LAN connection
All of the projector’s features can be controlled via a LAN connection, using a
standard internet browser package such as Internet Explorer.
rS232 connection
Computer
Crossed
LAN cable
Computer
Hub or
LAN
Un-crossed
LAN cables
Projector
Serial
RS232
LAN
Wired
remote
Projector
Projector
Projector
Page 45
Rev C April 2011 Page 2.21
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 2. Installation
Notes
Use only the power cable
provided.
Ensure that the power
outlet includes a Ground
connection, as this
equipment MUST be earthed.
Handle the power cable
carefully and avoid sharp
bends. Do not use a damaged
power cable.
Power connection
When mains power is first applied, the projector will perform a self-test, then go into
Standby mode.
The Power indicator on the control panel will show amber until the POWER
on the remote control or the keypad, is pressed for 3 seconds.
Power connection
Page 46
Page 2.22 Rev C April 2011
2. Installation Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Page 47
Rev C April 2011 Page 3.1
3. Getting Started
Contents
Switching the projector on ............................................................................................................... 3.2
Selecting an input or test pattern ................................................................................................... 3.2
Input ................................................................................................................................................ 3.2
Test pattern ...................................................................................................................................... 3.2
Adjusting the lens............................................................................................................................... 3.3
Focus .............................................................................................................................................. 3.3
Zoom ............................................................................................................................................... 3.3
Shift ................................................................................................................................................. 3.3
Adjusting the projected image ........................................................................................................ 3.4
Picture settings ................................................................................................................................. 3.4
Geometry settings ............................................................................................................................. 3.4
Switching the projector off ............................................................................................................... 3.4
Page 48
Page 3.2 Rev C April 2011
3. Getting Started Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Selecting an input or test pattern
Input
Press or to change to the next input up or down the following list:
1. RGB1
2. RGB2
3. DVI (Single)
4. SDI
5. Composite Video
6. S-Video
7. Component
8. DVI (Single/Dual/Twin pixel-mapped)
Or press the numbered keys 1–8 to change directly to the input:
Test pattern
If you have no video source connected to the projector, then you can display a test
pattern as follows:
Press
on the remote control, to select a test pattern.
•
•
•
Switching the projector on
Connect the power cable between the mains supply and the projector.
Wait until the self-test has completed and the power indicator on the control
panel shows amber. The lamp will be off, the shutter closed, and the projector
will be in STANDBY mode.
Press POWER
on the remote control or the keypad, and hold for about 3
seconds to switch the projector ON. The power indicator on the control panel will
show green, the lamp will light and the shutter will open.
•
•
Notes
For more information about
connecting the power cable,
see Power Connections, in
section 2. Installation.
For more detailed information
about:
- using the control keys on the
remote control or keypad,
- using the menus,
see the next section:
Controlling the projector.
3D images will be displayed in
3D, only if 3D Mode is set to on:
see section 4.Controlling the
projector, Setup Menu, 3D.
3D WUXGA images are
possible only on Input 8.
For important information about
how Input 8 is used, see INPUT
8 in the Notes column, and also
Section 4, Overview.
Only the Corrected White test
pattern on Input 8 will fill the
full height of the DMD, using all
1200 pixels. All other patterns
will be 1080 pixels high.
Power
connection
Page 49
Rev C April 2011 Page 3.3
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 3. Getting Started
Notes
Each time a new lens is
fitted to the projector,
the calibration procedure
must be carried out. See
Setup menu, in Section 4.
Controlling the projector.
For more detailed information
about:
- using the control keys on the
remote control or keypad,
- using the menus,
see the next section:
Controlling the projector.
When any of the three Lens
adjustment keys is pressed, the
blue Transmit indicator on the
remote control will light for 10
seconds:
- after 10 seconds, if no
adjustment has been made,
the indicator will go out and
the Lens adjustment key must
be pressed again to resume
adjustment.
- to end the adjustment before
10 seconds has elapsed, press
the
key.
- all other adjustments will
be locked out until the Lens
adjustment is ended.
Adjusting the lens
Focus
Press followed by and to adjust the focus.
When adjustment is finished, press .
Zoom
Press followed by and to adjust the zoom.
When adjustment is finished, press .
Shift
Press followed by , , or to shift the lens up, down, left or
right.
When adjustment is finished, press
.
•
•
•
Page 50
Page 3.4 Rev C April 2011
3. Getting Started Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
Adjusting the projected image
Picture settings
Press a key, followed by and to adjust these picture settings:
Brightness BRI
Contrast CON
Saturation SAT
Phase PHASE
Aspect ratio ASPECT
Geometry settings
Press Keystone KEYST
followed by and to adjust the keystone correction.
Press Position POS (for all inputs except DVI)
followed by , , and to adjust the picture position, for images
smaller than the DMD.
Switching the projector off
Press POWER on the remote control or keypad, and hold for 3 seconds,
to switch the projector OFF.
•
•
•
•
Notes
The Saturation control is
available for Composite, SVideo and Component inputs
only.
The Phase control is available
for RGB inputs only.
None of the Geometry controls
are available for Input 8.
For more detailed information
about:
- using the control keys on the
remote control or keypad,
- using the menus,
see the next section:
Controlling the projector.
For all adjustments that require
more than one key to be
pressed:
- after 10 seconds, if no
adjustment has been made,
the indicator will go out and
the adjustment key must be
pressed again.
- to end the adjustment before
10 seconds has elapsed, press
a different adjustment key, or
press the Exit key.
Always allow the lamp to cool
for 5 minutes before:
- disconnecting the power
- moving the projector
Page 51
Rev C April 2011 Page 4.1
4. Controlling the projector
Contents
Overview ............................................................................................................................................... 4.5
Controlling the projector..................................................................................................................... 4.5
Input modes and settings ................................................................................................................... 4.6
Input mode detection ....................................................................................................................... 4.6
Mode library and mode history ........................................................................................................... 4.6
Input presets .................................................................................................................................. 4.7
Special considerations when using Input 8 .......................................................................................... 4.8
Differences between Input 8 and Inputs 1-7 .......................................................................................... 4.8
Input and processing architecture ....................................................................................................... 4.8
Menu considerations when using Input 8 .............................................................................................. 4.8
Indicators .............................................................................................................................................. 4.9
Input status indicators ....................................................................................................................... 4.9
The control panel .............................................................................................................................. 4.10
Keypad layout................................................................................................................................. 4.10
Projector status indicators ................................................................................................................ 4.10
The remote control ............................................................................................................................4.11
Layout ............................................................................................................................................4.11
Timeout ...........................................................................................................................................4.11
Using the control keys .................................................................................................................... 4.12
Power ............................................................................................................................................ 4.12
Shutter ........................................................................................................................................... 4.12
On-Screen-Display .......................................................................................................................... 4.12
Focus ............................................................................................................................................ 4.12
Zoom ............................................................................................................................................. 4.12
Shift ............................................................................................................................................... 4.12
Calibrate Focus .............................................................................................................................. 4.13
Calibrate Zoom ............................................................................................................................... 4.13
Auto-detect input mode ................................................................................................................... 4.13
Source information .......................................................................................................................... 4.13
Input .............................................................................................................................................. 4.13
Input Presets .................................................................................................................................. 4.14
Recall ........................................................................................................................................4.14
Save .......................................................................................................................................... 4.14
Red, Green and Blue....................................................................................................................... 4.14
Test pattern .................................................................................................................................... 4.14
continued
Page 52
Page 4.2 Rev C April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Picture settings ............................................................................................................................... 4.15
Geometry settings ........................................................................................................................... 4.15
Magnify and pan ............................................................................................................................. 4.16
On-screen-display size .................................................................................................................... 4.16
Remote control address................................................................................................................... 4.16
Remote control backlight ................................................................................................................. 4.16
Using the menus ............................................................................................................................... 4.17
Navigating menus and submenus ..................................................................................................... 4.17
Menu controls ................................................................................................................................. 4.19
Input menu .........................................................................................................................................4.20
Input Source ................................................................................................................................... 4.20
Presets .......................................................................................................................................... 4.21
Recall Presets .............................................................................................................................. 4.21
Save Presets ............................................................................................................................... 4.22
Delete Presets ............................................................................................................................. 4.23
Picture menu ...................................................................................................................................... 4.24
Brightness ...................................................................................................................................... 4.24
Contrast ......................................................................................................................................... 4.24
Saturation ...................................................................................................................................... 4.24
Hue ............................................................................................................................................... 4.24
Gamma Correction .......................................................................................................................... 4.25
Parametric Gamma ......................................................................................................................... 4.25
Phase ............................................................................................................................................ 4.25
Aspect Ratio ................................................................................................................................... 4.26
Sharpness ...................................................................................................................................... 4.26
Geometry menu ................................................................................................................................. 4.27
Horizontal Position .......................................................................................................................... 4.27
Vertical Position .............................................................................................................................. 4.27
Aspect Ratio ................................................................................................................................... 4.27
User Horizontal Aspect Ratio ........................................................................................................... 4.28
User Vertical Aspect Ratio ............................................................................................................... 4.28
Keystone ........................................................................................................................................ 4.28
Phase ............................................................................................................................................ 4.28
Resolution ...................................................................................................................................... 4.29
Input Detection ............................................................................................................................. 4.29
Blanking ......................................................................................................................................... 4.30
Blanking On/Off ............................................................................................................................ 4.30
Blanking adjust ............................................................................................................................. 4.30
continued
Page 53
Rev C April 2011 Page 4.3
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Colour menu ......................................................................................................................................4.31
Colour Mode................................................................................................................................... 4.32
Colour Temperature ........................................................................................................................4.32
RGB Lift ......................................................................................................................................... 4.32
RGB Gain ...................................................................................................................................... 4.32
Component Type ............................................................................................................................ 4.32
Trim ............................................................................................................................................... 4.33
Trim RGB Lift and Gain ..................................................................................................................4.33
Global Colourimetry ....................................................................................................................... 4.33
Setup menu ........................................................................................................................................ 4.34
Projector Setup ............................................................................................................................... 4.35
Orientation .................................................................................................................................. 4.35
Control Panel Backlight .................................................................................................................. 4.35
Keystone ........................................................................................................................................ 4.36
DVI EDID Extension Block .............................................................................................................. 4.36
Test Patterns .................................................................................................................................. 4.37
FastFrame ..................................................................................................................................... 4.38
FastFrame On/Off ......................................................................................................................... 4.38
Dark Time ................................................................................................................................... 4.38
Edge Blend .................................................................................................................................... 4.39
Examples .................................................................................................................................... 4.39
Active Edges ...............................................................................................................................4.39
Overlap markers ........................................................................................................................... 4.40
Overlap adjust .............................................................................................................................. 4.40
Input 8 DVI 3D Resolution ............................................................................................................... 4.40
Black Level Uplift ............................................................................................................................ 4.41
Examples .................................................................................................................................... 4.41
Uplift Adjustment .......................................................................................................................... 4.41
Non-Addressable Border ................................................................................................................ 4.42
Border Adjustment ........................................................................................................................ 4.42
Global Colourimetry ........................................................................................................................ 4.43
Colour Mode ................................................................................................................................ 4.44
Colour Temperature....................................................................................................................... 4.44
RGB Lift ..................................................................................................................................... 4.44
RGB Gain ................................................................................................................................... 4.44
Lamp Setup .................................................................................................................................... 4.45
Change Lamp Setting .................................................................................................................... 4.45
Lamp Power ................................................................................................................................ 4.46
Lamp Mode ................................................................................................................................. 4.46
continued
Page 54
Page 4.4 Rev C April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
On Screen Display .......................................................................................................................... 4.47
OSD Position ............................................................................................................................... 4.47
OSD Size .................................................................................................................................... 4.47
OSD Timeout ............................................................................................................................... 4.47
Password ....................................................................................................................................... 4.48
Communication Setup ..................................................................................................................... 4.49
Serial Port Baud Rate .................................................................................................................... 4.49
Projector Address ......................................................................................................................... 4.49
Network Setup ................................................................................................................................ 4.50
LAN MAC Address ........................................................................................................................ 4.50
Connection .................................................................................................................................. 4.50
DHCP ........................................................................................................................................ 4.51
IP Address .................................................................................................................................. 4.51
Subnet Mask ...............................................................................................................................4.52
Gateway Mask ............................................................................................................................. 4.53
Wifi Channel ................................................................................................................................ 4.53
SSID .......................................................................................................................................... 4.53
3D Setup ........................................................................................................................................ 4.54
3D Mode ..................................................................................................................................... 4.54
3D Input Assign ............................................................................................................................ 4.54
3D Format ................................................................................................................................... 4.55
Dark Time ................................................................................................................................... 4.56
Frame Dominance ........................................................................................................................4.56
3D Sync Delay ............................................................................................................................. 4.57
3D Sync Source ........................................................................................................................... 4.57
3D Sync Output Polarity ................................................................................................................. 4.57
Output Shuttering (Frame Rate Multiplication) ..................................................................................... 4.58
x2 Example ................................................................................................................................. 4.58
Lens Setup ..................................................................................................................................... 4.59
Centre Lens ................................................................................................................................. 4.59
Calibrate Focus ............................................................................................................................ 4.59
Calibrate Zoom ............................................................................................................................ 4.59
Restore Defaults ............................................................................................................................. 4.60
Information menu .............................................................................................................................4.61
Projector Information ....................................................................................................................... 4.61
Source Information .......................................................................................................................... 4.61
Digital Projection Information ........................................................................................................... 4.62
Page 55
Rev C April 2011 Page 4.5
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Overview
Controlling the projector
The projector can be controlled from:
the remote control
the keypad
the RS232 input
the Ethernet input
For more information about controlling the projector using the RS232 and
Ethernet inputs, see Remote communications protocol in
section 7.
Appendix.
For information about how to connect the projector, see Connecting the
projector in section 2. Installation, and
Connections in section 7. Appendix.
Many features are controlled from the menus using the menu navigation keys on
the remote control or keypad.
For more information about using the menus, see later in this section, Using the
menus.
Some of the menu features, for example brightness, contrast and input preset
operations, can be accessed directly using the control keys at the bottom of the
remote control.
Other features, eg zoom and focus, are controlled using the control keys at the
top of the remote control and keypad.
For more information about using the control keys, see later in this section,
Using the control keys.
•
•
•
•
•
•
•
Notes
Menu navigation keys
Control keys
Page 56
Page 4.6 Rev C April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Input modes and settings
Input mode detection
The projector can automatically detect the following parameters from the incoming
video signal:
line frequency
frame rate
interlace / progressive
From these parameters the projector can determine input mode, for example:
input source horizontal vertical mode
composite 15.73KHz 60.0Hz = NTSC
RGB1 31.51KHz 60.0Hz = SDTV 480p
DVI 64.02KHz 60.0Hz = SXGA 60
When you select a new input source, the green LED near the input connector will
flash, and the searching message will be displayed.
When the input mode has been detected, the LED will show continuously and the
auto detect message will be displayed, for example:
If the input mode cannot be detected, the LED will continue to flash, to show that the
input is still selected. However, the following message will be displayed:
Mode library and mode history
Once an input mode has been successfully determined for the first time, a set of
default modal settings (picture, geometry and colour), will be copied from the mode
library to the mode history.
•
•
•
•
•
•
•
NTSC
mode
detected
Mode
library
defaults
SDTV
480p
HDTV
1080p
SVGA
defaults
defaults
defaults
Mode
history
Notes
For a full list of supported input
modes, see Input modes
supported, in section 7.
Appendix.
Page 57
Rev C April 2011 Page 4.7
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Any subsequent changes that you make to the modal settings will be saved in the
mode history, with the input mode.
If a new signal is detected, the mode history for the previous signal will be saved in
the mode history, and the new mode added, along with a new set of default settings.
Thus the projector builds up a history of input modes, and the required settings for
each mode, depending on actual useage.
Input presets
It may be the case that you need to save more than one set of modal settings for
the same input mode. For example you may have more than one video player or a
selection of films with different characteristics.
In that case, the current input source and modal settings can be saved to any one of
16 input presets, for recall when the same input source is used again.
When you recell a preset, the projector switches to the saved input source, and
redetects the input mode before applying the saved modal settings.
NTSC
new
modal
settings
defaults
SDTV
480p
HDTV
1080p
SVGA
defaults
defaults
defaults
Mode
history
Mode
library
NTSC
NTSC
new
mode
detected
defaults
SDTV
480p
HDTV
1080p
SVGA
defaults
defaults
defaults
Mode
history
Mode
library
NTSC
settings
DVI
settings
SVGA
1) input
switched
2) mode
redetected
3) settings
applied
preset
saved
Mode
history
NTSC
settings
Input
presets
SVGA
settings
A
B
C
D
RGB
settings
DVI
settings
DVI
SVGA
SDTV
Notes
In normal use, there should be
adequate memory to record
all likely modal settings in the
mode history.
However, in exceptional
circumstances, the least used
settings will be deleted, to allow
a new mode to be added.
The mode library and mode
history described here do not
apply to Input 8.
A single set of parameters
(input mode, picture, colour,
but not geometry) are stored
for Input 8, and these will be
recalled whenever Input 8 is
selected.
For more information about
presets, see Input Menu, later
in this section.
For more information about
presets, see Input Menu, later
in this section.
A preset can be applied only to
the same mode for which it was
created. If the detected input
mode does not match, then
settings from the mode history
or mode library will be applied.
Page 58
Page 4.8 Rev C April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Special considerations when using Input 8
Differences between Input 8 and Inputs 1-7
Input 8 has been designed to offer the user access to a very high bandwidth digital
video path, free of the limitations inherent to standard image processing techniques.
As such, the image is pixel-mapped directly to the DMDs, so only a subset of the
Image Controls applicable to Inputs 1-7 apply to Input 8.
Projector level controls, such as input selection, lens and lamp control are all
applicable to Input 8, but modal settings are not. The menus affected are described
below.
Input and processing architecture
Menu considerations when using Input 8
The following menus are limited:
Input menu: Input Presets are limited to the lens mount settings.
Picture menu: Aspect Ratio setting is NOT available.
Geometry menu: As the image is pixel-mapped directly to the DMDs, NONE of
the geometry settings are available.
Projector Setup menu: Keystone adjustment is NOT available; Test Pattern is
limited to 100% Field (Corrected White).
Notes
For important information
about how Input 8 is used, see
notes like this one in the Notes
column, marked INPUT 8.
Page 59
Rev C April 2011 Page 4.9
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
There are more indicators on
the Control panel, and these are
described on the next page.
Input 8 and 3D may not be
present on some models
Indicators
Input status indicators
The indicator next to each input connector on the rear input panel will light as
follows:
off = input not selected
green = input selected, signal detected and in range
flashing green = input selected, but signal not detected or out of range
The indicator next to each input connector on the front input panel will light as
follows:
off = input not selected
green = input selected, signal detected and in range
flashing green = input selected, but signal not detected or out of range
5. Composite Video
6. S-Video
7. Component
1. RGB1
2. RGB2
3. DVI
4. SDI
8. DVI:
MAIN
SUB
3D Sync OUT
3D Sync IN
Page 60
Page 4.10 Rev C April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
Many features are controlled
from the menus using the menu
navigation keys on the remote
control or keypad.
For more information about
using the menus, see later in
this section, Using the menus.
Some of the menu features, for
example brightness, contrast
and input preset operations, can
be accessed directly using the
control keys at the bottom of
the remote control.
Other features, eg zoom and
focus, are controlled using the
control keys at the top of the
remote control and keypad.
For more information about
using the control keys, see
later in this section, Using the
control keys.
The Lamp 2 indicator applies
only to Titan Dual models.
The control panel
Keypad layout
The controls on the keypad are identical to those at the top of the remote control,
and are described on the following pages.
Projector status indicators
The indicators on the control panel are as follows:
Power
off = NO POWER
green = normal RUNNING mode amber = STANDBY mode
Shutter
amber = CLOSED green = OPEN
Error
off = NO ERROR
flashing = ERROR (temperature) steady = ERROR (voltage)
IR blue flash = Remote control command received
Lamp 1
off = OFF
flashing red = LAMP ERROR green = ON (100%) amber = (80 - 99%)
flashing green = LAMP WARM-UP flashing amber = COOL-DOWN
Lamp 2
off = OFF
flashing red = LAMP ERROR green = ON (100%) amber = (80 - 99%)
flashing green = LAMP WARM-UP flashing amber = COOL-DOWN
Page 61
Rev C April 2011 Page 4.11
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
The remote control
Layout
Timeout
There is a 10 second timeout for the three Lens adjustment keys (see note on next
page).
There is a separate, adjustable timeout for the On Screen Menus (see On Screen
Display, in Setup Menu, later in this section).
Notes
Many features are controlled
from the menus using the menu
navigation keys on the remote
control or keypad.
For more information about
using the menus, see later in
this section, Using the menus.
Some of the menu features, for
example brightness, contrast
and input preset operations, can
be accessed directly using the
control keys at the bottom of
the remote control.
Other features, eg zoom and
focus, are controlled using the
control keys at the top of the
remote control and keypad.
For more information about
using the control keys, see
later in this section, Using the
control keys.
The following keys are NOT
used on this projector:
CTRL
FUNC
10+
(but N is used)
# (but R is used)
There are two infra-red
windows - see Getting to
know the projector, in section
1. Introduction.
Note that plugging in the remote
control cable will disable the
infra-red.
Menu
navigation
keys
Remote control
backlight
ON/OFF
Control keys
Transmit
indicator
Page 62
Page 4.12 Rev C April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
Closing the shutter produces
a better black than simply
removing the signal, as the
light source will be completely
blocked by the shutter blade.
When the OSD is OFF:
- all menu navigation keys are
disabled.
- keys such as BrI
(brightness) will still function,
but the slider bars will not be
visible on screen.
When any of the three Lens
adjustment keys is pressed, the
blue Transmit indicator on the
remote control will light for 10
seconds:
- after 10 seconds, if no
adjustment has been made,
the indicator will go out and
the Lens adjustment key must
be pressed again to resume
adjustment.
- to end the adjustment before
10 seconds has elapsed, press
the
key.
- all other adjustments will
be locked out until the Lens
adjustment is ended.
For more information about the
amount of lens shift available,
see section 2. Installation.
Using the control keys
Power
Press POWER and hold for 3 seconds, to switch the projector ON.
Press POWER and hold for 3 seconds, to switch the projector OFF.
Shutter
Press SHUTTER to OPEN the shutter.
Press SHUTTER to CLOSE the shutter.
On-Screen-Display
Press OSD to switch the On-Screen-Display OFF.
This includes ALL menus, controls and on-screen messages.
Press OSD to switch the On-Screen-Display ON.
Focus
Press followed by and to adjust the focus.
When adjustment is finished, press .
Zoom
Press followed by and to adjust the zoom.
When adjustment is finished, press .
Shift
Press followed by , , or to shift the lens up, down, left or
right.
When adjustment is finished, press
.
•
•
•
•
•
•
•
•
•
Page 63
Rev C April 2011 Page 4.13
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Calibrate Focus
Press followed by to calibrate the lens focus mechanism.
Calibrate Zoom
Press followed by to calibrate the lens zoom mechanism.
Auto-detect input mode
Press to force the projector to re-detect the input mode and apply the
default modal settings.
(see Input modes and settings, earlier in this section).
Source information
Press to display the source information screen.
Input
Press or to change to the next input up or down the following list:
1. RGB1
2. RGB2
3. DVI (Single)
4. SDI
5. Composite Video
6. S-Video
7. Component
8. DVI (Single/Dual/Twin pixel-mapped)
Or press the numbered keys 1–8 to change directly to the input:
•
•
•
•
•
•
Notes
Each time a new lens is
fitted to the projector,
the calibration procedure
must be carried out. See
Setup menu, in Section 4.
Controlling the projector.
For more information about
input mode detection, see
earlier in this section, Input
modes and settings.
For more information about
the input connections, see
section 2. Installation, and
section 7. Appendix.
Input 8 and 3D may not be
present on some models
3D signals will be displayed
in 3D, only if 3D Enable is set
to on: see later in this section,
Setup Menu, 3D.
WUXGA models only:
3D images are possible only on
Input 8.
When an input has been
selected, the projector will
automatically detect input mode
settings such as line rate and
resolution etc.
To force the projector to re-
detect the input mode settings,
press
.
Page 64
Page 4.14 Rev C April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
For more information about
input modes and input presets,
see earlier in this section, Input
modes and settings.
See also Input menu, later in
this section.
A preset can be applied only to
the same mode for which it was
created. If the detected input
mode does not match, then
settings from the mode history
or mode library will be applied.
For more information about
input modes, see Input modes
and settings. earlier in this
section.
The lens settings, ie Focus
position, Zoom position and
Shift, are included only for the
first ten presets.
The lens settings are the only
settings saved for Input 8.
The red, green and blue keys
are disabled when the OSD is
switched OFF.
For more information about test
patterns, see Setup menu, later
in this section.
Input Presets
recall
To recall a set of modal and lens settings that have been saved, press and hold
, whilst pressing the lettered key A – S.
The projector will switch to the saved input source, and redetect the input mode
before applying the saved modal and lens settings.
Save
To save the current input source, modal and lens settings, press and hold ,
whilst pressing the lettered key A – S.
If this Preset has been used before, and the Input source has been changed,
then the following message will be displayed.
Press and to select either OK or Cancel.
Press to confirm your selection.
The settings will be saved to the selected preset, and the following message will
be displayed.
Red, Green and Blue
Press , or to switch the red, green or blue components OFF
or ON.
Test pattern
Press to select a test pattern.
•
•
•
•
•
•
•
•
Page 65
Rev C April 2011 Page 4.15
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
The Saturation control is
available for Composite, SVideo and Component inputs
only.
The Phase control is available
for RGB inputs only.
The Geometry settings are
NOT available for Input 8.
For all adjustments on this page
that require more than one key
to be pressed:
- after 10 seconds, if no
adjustment has been made, the
key must be pressed again
to resume adjustment.
- to end the adjustment before
10 seconds has elapsed, press
a different adjustment key, or
press the
key.
When the OSD is OFF:
- the keys will still function,
but the controls will not be
visible on screen.
Picture settings
Press a key, followed by and to adjust these picture settings:
Brightness BRI
Contrast CON
Saturation SAT
Phase PHASE
Aspect ratio ASPECT
Geometry settings
Keystone adjustment is used to correct for distortion caused by the projector being
mounted higher or lower than the screen.
Press Keystone KEYST,
followed by and to adjust the keystone correction:
Position adjustment is used for images smaller than the DMD.
Press Position POS,
followed by and to select the horizontal or vertical slider,
then and to adjust the picture position:
•
•
•
Page 66
Page 4.16 Rev C April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
The magnify feature utilises a
digital zoom. Used with the pan
control, this can be used to:
- enlarge a section of the image
- enable the use of multiple
projectors to construct a large
image from tiles.
The pan control is available
only when the image has been
magnified.
The Magnify and pan controls
are NOT available for Input 8.
If the OSD moves off screen
due to a change in image size,
then pressing the size key will
restore its readability.
When fresh batteries are
inserted in the remote control
it will default to address 00.
Remote control 00 is a master
control, able to control all
projectors.
If two or more projectors are set
to the same address, they can
be controlled from one remote
control, provided they are
connected by cable or in range
of the infra red.
Magnify and pan
Press Magnify MAGNIFY
followed by and to adjust the size of the picture.
Press Pan PAN
followed by , , and to adjust the position of the magnified image.
On-screen-display size
Press OSD OSD
to switch the size of the OSD between large and small.
Remote control address
The projector and the remote control need to be set to matching addresses. Read
the note to the right on this page, and follow the instructions in the order shown
below:
1
Set the projector address as shown in Setup menu, later in this section.
2
Set the remote control address:
Press and hold
whilst pressing two numbered keys 0 – 9
to set the remote control address to any number between 00 and 99.
(leading zeros must be used for numbers less than 10)
Remote control backlight
Press to switch the backlight on and off.
•
•
•
•
•
Page 67
Rev C April 2011 Page 4.17
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
Some menu controls can be
accessed directly using the
control keys (see earlier in this
section).
When the OSD is OFF, all menu
navigation keys will be disabled.
When the OSD is switched back
ON, the menus will remain OFF
until the
key is pressed
again. The menus will then
reopen at the same point they
were last viewed.
If a menu is opened, and no
other key is pressed within the
period set in the OSD Timeout
menu, then the menus will
disappear. When the
key
is pressed again, the menus will
reopen at the same point they
were last viewed.
(see On Screen Display,
in Setup Menu, later in this
section).)
Main menu: Input
Main menu: Setup
Using the menus
Navigating menus and submenus
When the menus are in use and the OSD is ON, the top level menu headings are
always visible to the left of the screen.
Each menu item can lead to a number of submenus, which are displayed in the
column to the right . The
symbol indicates that a submenu is available.
Each submenu can lead to further submenus, up to a maximum of three levels.
To display the menus, press
on the remote control or the keypad.
The menus will always open at the same point they were last viewed. The
example below shows the first menu display following power on – the item that is
currently selected (the Input menu) is highlighted in blue.
To select a menu, press
and , for example the Setup menu:
•
•
•
Page 68
Page 4.18 Rev C April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Press to open the menu. The blue highlight moves to the first item in the
menu, which may be submenu, for example the Projector Setup submenu.
To select a submenu, press
and , for example the Lamp submenu.
Press
to open the submenu. The submenu opens, with the title at the top.
To close the submenu and return to the previous level, press .
There may be up to three levels of submenu, so to return to the top level, you
may have to press
up to three times.
To close the menu display completely, press .
•
•
•
•
•
Notes
Setup menu
Setup menu
Lamp
Setup menu
Page 69
Rev C April 2011 Page 4.19
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Slider bar
The highlighted slider bar shows which
control is active currently.
To adjust the slider press
and .
Parameter selection
To select from a number of parameters,
(shown one at a time to the right),
press
and .
These two items are greyed out and
the values are blank, showing that they
are not available, due to the effect of
settings made in other menus, or due
to the type of input signal.
Parameter list
To select from a list of parameters,
press
and .
Menu controls
Some menus have controls, as shown in the examples below.
Notes
Some menus items may be
greyed out - unavailable due to
the effect of settings made in
other menus, or due to the type
of input signal.
Page 70
Page 4.20 Rev C April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Input menu
To return to the main menu, press up to three times.
From the main menu:
Press
and until Input is highlighted.
Press to open the Input menu. The blue highlight moves to the first item in
the menu. The symbol shows which input is currently selected.
Input Source
Press and to select from:
1. RGB1
2. RGB2
3. DVI (Single)
4. SDI
5. Composite Video
6. S-Video
7. Component
8. DVI (Single/Dual/Twin pixel-mapped)
Press
to confirm your selection.
•
•
•
Notes
Some menu controls can be
accessed directly using the
control keys (see earlier in this
section).
When using the menus, press
OSD or to hide or
reveal the On-Screen-Display.
Input Menu
For more information about
the input connections, see
section 2. Installation, and
section 7. Appendix.
Input 8 and 3D may not be
present on some models
3D signals will be displayed
in 3D, only if 3D Enable is set
to on: see later in this section,
Setup Menu, 3D.
WUXGA models only:
3D images are possible only on
Input 8.
When an input has been
selected, the projector will
automatically detect input mode
settings such as line rate and
resolution etc.
To force the projector to re-
detect the input mode settings,
press
.
Page 71
Rev C April 2011 Page 4.21
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
Some menu controls can be
accessed directly using the
control keys (see earlier in this
section).
For more information about
input modes and input presets,
see earlier in this section, Input
modes and settings.
The lens settings are the only
settings saved for Input 8.
Input Menu
Presets
Input Menu
Presets
Recall Presets A ~ H
The lens settings, ie Focus
position, Zoom position and
Shift, are included only for the
first ten presets.
The lens settings are the only
settings recalled for Input 8.
Presets
Sixteen sets of parameters can be saved and recalled (A – S). The parameters
saved for each Preset are:
all settings from the Picture menu,
all settings from the Input menu
all settings from the Geometry menu, except Keystone
all settings from the Colour menu, except the Global settings
all lens position, focus and zoom settings
Press
and to select Presets.
Press to open the Presets submenu.
recall presets
Press and to select Recall Preset.
Press to open the Recal Presets A ~ H submenu. Any presets that have
been saved are indicated by their description, for example D: in this example.
To recall a set of parameters that has been saved, press
and to select
one of the Presets.
For Presets J to S, select Recall Preset J ~ S then press to open the
J~S submenu. Press and to select the Preset.
Press to confirm your selection.
The Preset parameters will be loaded.
•
•
•
•
Input menu continued
Page 72
Page 4.22 Rev C April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
Some menu controls can be
accessed directly using the
control keys (see earlier in this
section).
Input Menu
Presets
Save Presets A ~ H
The lens settings, ie Focus
position, Zoom position and
Shift, are included only for the
first ten presets.
The lens settings are the only
settings saved for Input 8.
Save presets
Press and to select Save Preset.
Press to open the Save Presets A ~ H submenu.
To save the current set of parameters, press and to select one of the
Presets.
For Presets J to S, select Save Preset J ~ S then press to open the
J~S submenu. Press and to select the Preset.
Press to confirm your selection.
If this Preset has been used before, but only if the Input source has been
changed, then the following message will be displayed.
Press and to select either OK or Cancel.
Press to confirm your selection.
The parameters will be saved to the selected preset, and the following message
will be displayed.
•
•
Input menu continued
Page 73
Rev C April 2011 Page 4.23
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
Input Menu
Presets
Delete Presets A ~ H
Delete presets
Press and to select Delete Preset.
Press to open the Delete Presets A ~ H submenu.
To delete a saved set of parameters, press and to select one of the
Presets.
For Presets J to S, select Delete Preset J ~ S then press to open the
J~S submenu. Press and to select the Preset.
Press to confirm your selection.
The following message will be displayed.
Press and to select either OK or Cancel.
Press to confirm your selection.
The preset will be deleted, and the following message will be displayed.
•
•
Input menu continued
Page 74
Page 4.24 Rev C April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
Some menu controls can be
accessed directly using the
control keys (see earlier in this
section).
When using the menus, press
OSD or to hide or
reveal the On-Screen-Display.
Picture Menu
Some menu items may be
greyed out - unavailable due to
the effect of settings made in
other menus, or due to the type
of input signal.
The Saturation slider is
available for Composite, SVideo and Component inputs
only.
The Hue slider is available for
NTSC inputs only.
Picture menu
To return to the main menu, press up to three times.
From the main menu:
Press
and until Picture is highlighted.
Press to open the Picture menu. The blue highlight moves to the first item in
the menu.
Brightness
Press and to select Brightness.
Press and to adjust the slider (-128 to +127).
Contrast
Press and to select Contrast.
Press and to adjust the slider (-128 to +127).
Saturation
Adjusts the saturation at white peak levels.
Press
and to select Saturation.
Press and to adjust the slider (0 to 255).
Hue
Adjusts the color balance from green to blue, using the red level as a reference.
Press
and to select Hue.
Press and to adjust the slider (0 to 255).
•
•
•
•
•
Page 75
Rev C April 2011 Page 4.25
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
For more information about
User gamma settings, see
section 5. Userware.
Parametric Gamma adjustment
is available only when
Parametric is selected in
Gamma selection, above.
Phase adjustment can be
found in both the Picture and
Geometry menus, and is
available for RGB1 and RGB2
inputs only.
The Phase adjustment is NOT
available for Input 8.
Gamma Correction
Video recordings are often supplied with a gamma adjustment applied. The
projector’s gamma adjustment can be used to correct for this.
Press
and to select Gamma.
Press and to select from:
Parametric Enables the gamma slider
User download Applies the gamma settings made externally using the DP
Userware on a personal computer. (default gamma of 2.2)
2.2 Limited DVI
Expands DVI signal to use full dynamic range with gamma 2.2
2.4 Limited DVI Expands DVI signal to use full dynamic range with gamma 2.4
Graphics Enhanced highlights and contrast
NTSC NTSC colour space, with a gamma of 2.2
PAL PAL colour space, with a gamma of 2.2
Linear gamma of 1.0
Punch Enhanced brightness and increased colour saturation for high
ambient environments.
Parametric Gamma
Press and to select Parametric Gamma.
Press and to adjust the slider (1.0 to 3.0 in 0.1 steps).
Phase
Phase should be set automatically by the projector, but can be adjusted manually to
correct for shimmering or poor quality definition on, for example, fine text.
Press
and to select Phase.
Press and to adjust the slider (0 to 31).
•
•
•
picture menu continued
Page 76
Page 4.26 Rev C April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
Aspect Ratio selection can be
found in both the Picture and
Geometry menus.
When User Aspect is selected,
the Aspect Ratio settings are
taken from the User H Aspect
and V Aspect settings made in
the Geometry menu.
Aspect Ratio selection is NOT
available for Input 8.
WUXGA models only:
The full height of the DMD can
be used only by WUXGA and
UXGA images.
For more information, see
Screen requirements in
section 2. Installation.
The Sharpness slider is
available for Composite,
S-Video and Component SD
inputs only.
Aspect Ratio
Press and to select Aspect Ratio.
Press and to select from:
Fill This will best fit the incoming source to fill either the height or
width without changing the aspect ratio of the source.
User Aspect
1.33:1 (4:3)
1.6:1 (16:10)
1.78:1 (16:9)
2.35:1 (Scope)
1.66:1 (Vista)
1.85 (Flat)
Theaterscope
Use with the TheaterScope Anamorphic System only. The
2.35:1 source image is displayed using the full area of the 16:9
DMD. This is then stretched to 2.35:1 by the lens.
Native
The image will be displayed pixel for pixel. The image will be
centred, with a black border if smaller than full resolution or
cropped if larger.
Sharpness
Press and to select Sharpness.
Press and to adjust the slider.
•
•
picture menu continued
Page 77
Rev C April 2011 Page 4.27
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
Some menu controls can be
accessed directly using the
control keys (see earlier in this
section).
When using the menus, press
OSD or to hide or
reveal the On-Screen-Display.
Geometry Menu
None of the Geometry controls
are available for Input 8.
Some menu items may be
greyed out - unavailable due to
the effect of settings made in
other menus, or due to the type
of input signal.
Aspect Ratio selection can be
found in both the Picture and
Geometry menus.
When User Aspect is selected,
the Aspect Ratio settings are
taken from the User H Aspect
and V Aspect settings (see
next page).
WUXGA models only:
The full height of the DMD can
be used only by WUXGA and
UXGA images.
For more information, see
Screen requirements in
section 2. Installation.
Geometry menu
To return to the main menu, press up to three times.
From the main menu:
Press
and until Geometry is highlighted.
Press to open the Geometry menu. The blue highlight moves to the first item
in the menu.
Horizontal Position
Press and to select H Position.
Press and to adjust the slider.
Vertical Position
Press and to select V Position.
Press and to adjust the slider.
Aspect Ratio
Press and to select from:
Fill This will best fit the incoming source to fill either the height or
width without changing the aspect ratio of the source.
User Aspect
1.33:1 (4:3)
1.6:1 (16:10)
1.78:1 (16:9)
2.35:1 (Scope)
1.66:1 (Vista)
1.85 (Flat)
Theaterscope
Use with the TheaterScope Anamorphic System only. The
2.35:1 source image is displayed using the full area of the 16:9
DMD. This is then stretched to 2.35:1 by the lens.
Native
The image will be displayed pixel for pixel. The image will be
centred, with a black border if smaller than full resolution or
cropped if larger.
•
•
•
•
Input
Picture
Geometry
Colour
Setup
Information
H Position
V Position
Aspect Ratio
User H Aspect
User V Aspect
Keystone
Phase
Resolution
Blanking
1.85:1 (Flat)
128
64
500
500
0
127
Page 78
Page 4.28 Rev C April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
None of the Geometry controls
are available for Input 8.
Horizontal and Vertical
Aspect Ratio adjustments are
available only when User is
selected in Aspect Ratio, (see
previous page).
WUXGA models only:
The full height of the DMD can
be used only by WUXGA and
UXGA images.
For more information, see
Screen requirements in
section 2. Installation.
Keystone adjustment can be
found in both the Geometry and
Projector Setup menus.
The range of adjustment will
be dependent on the input
resolution.
Phase adjustment can be
found in both the Picture and
Geometry menus, and is
available for graphics based
RGB sources only.
User Horizontal Aspect Ratio
Press and to select User H Aspect.
Press and to adjust the slider (internal number – adjust to fit).
User Vertical Aspect Ratio
Press and to select User V Aspect.
Press and to adjust the slider (internal number – adjust to fit).
Keystone
Used to correct for distortion caused by the projector being mounted higher or lower
than the screen.
Press
and to select Keystone.
Press and to adjust the slider.
Phase
Phase should be set automatically by the projector, but can be adjusted manually to
correct for shimmering or poor quality definition on, for example, fine text.
Press
and to select Phase.
Press and to adjust the slider (0 to 32).
•
•
•
•
Geometry menu continued
Page 79
Rev C April 2011 Page 4.29
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
None of the Geometry controls
are available for Input 8.
Geometry Menu
Resolution
Input Detection should
normally be set to Automatic.
However, if the incoming video
signal is non-standard, the
projector may not be able to
select an appropriate input
mode.
In this case, Input Detection
should be set to Manual or
Custom.
Input Standard is available
only if Input Detection is set to
Manual.
WUXGA models only:
The full height of the DMD can
be used only by WUXGA and
UXGA images.
For more information, see
Screen requirements in
section 2. Installation.
Resolution
Press and to select Resolution.
Press to open the Resolution submenu.
Input Detection
Press and to select from:
Automatic Allows the projector to automatically detect an appropriate
input mode for the signal.
Manual Allows the user to select an appropriate input mode from a list
of common standards.
Custom Allows the user to completely customise the settings to suit the
incoming video signal.
When Input Detection is set to Manual:
Press
and to select Input Standard.
Press and to select from:
720p
XGA
XGA+
SXGASXGA
SXGA+
1080p
UXGA
WUXGA
VGA
NTSC
PAL
SVGA
•
•
•
•
Geometry menu continued
Page 80
Page 4.30 Rev C April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
When Input Detection is set to Custom:
Press and to select one of the adjustment sliders.
Press and to adjust the slider to match the resolution of the incoming
video signal.
Blanking
Blanking curtains can be applied to each edge of the picture.
Press
and to select Blanking.
Press to open the Blanking submenu.
Blanking On/Off
Press and to select from:
On
Off
Blanking adjust
Press and to select the edge to be blanked.
Press and to adjust the slider (0 to 200).
•
•
•
•
Notes
None of the Geometry controls
are available for Input 8.
The adjustment sliders are
available only if Input Detection
is set to Custom.
Total H Samples is available
for RGB1 and RGB2 inputs
only.
V Offset is available for DVI
input only.
WUXGA models only:
The full height of the DMD can
be used only by WUXGA and
UXGA images.
For more information, see
Screen requirements in
section 2. Installation.
Geometry Menu
Blanking
The blanking curtains will not
applied until Blanking is turned
On.
The On Screen Display will
move to the centre of the DMD
when Blanking is turned On.
Set to zero for no blanking, eg
the top edge in this example.
Geometry menu continued
Page 81
Rev C April 2011 Page 4.31
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
When using the menus, press
OSD or to hide or
reveal the On-Screen-Display.
Colour Menu
Some menu items may be
greyed out - unavailable due to
the effect of settings made in
other menus, or due to the type
of input signal.
Read these notes on Colour
and Global Colourimetry
before making any settings in
the Colour menus.
Note that any changes made
in the Global Colourimetry
menu (see Setup Menu, later
in this section) will affect ALL
inputs, modes and presets for
which Global Mode has been
selected in the Colour menu.
Colour menu
To return to the main menu, press up to three times.
From the main menu:
Press
and until Colour is highlighted.
Press to open the Colour menu. The blue highlight moves to the first item in
the menu.
•
Notes on Colour and Global Colourimetry
Global Colourimetry menu (see later in this section, in Setup menu)
After a calibration check on the projector or venue, a set of Global colour settings
can be made in the Global Colourimetry menu. These settings are then available
to be copied at any time using the Colour Mode setting in the Colour menu, or
used as a starting point using the Trim feature in the Colour menu.
Colour menu (see this section).
The settings made in the Colour menu will be automatically saved in the Mode
History, or can be manually saved to one of the Input Presets (see Input modes
and settings earlier in this section).
The selections available in Colour Mode in the Colour menu are:
Global
Copies the settings made in the Global Colourimetry menu
Temperature Set the colour temperature using the slider
User Set the Red, Green and Blue Lift and Gain using the sliders
Peak Preset high brightness setting
Video, Film,
Graphic
Applies the factory set P7 settings
ColorMAX User Applies the User gamma settings made externally using the
DP Userware on a personal computer
Page 82
Page 4.32 Rev C April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
Read the notes on Colour and
Global Colourimetry earlier
in this section before making
any settings in the Colour
menus.
Note that any changes made
in the Global Colourimetry
menu (see Setup Menu, later
in this section) will affect ALL
inputs, modes and presets for
which Global Mode has been
selected in the Colour menu.
The Colour Temperature
slider is available only if
Temperature Mode is selected.
The RGB Lift and Gain sliders
are available only if User Mode
is selected.
The Component Type
selection is available for RGB1
and Component inputs only.
Colour Mode
Press and to select Colour Mode.
Press and to select from:
Global
Temperature
User
Peak
Video
Film
Graphic
ColorMAX User 1
ColorMAX User 2
Colour Temperature
Press and to select Temperature.
Press and to adjust the slider (3,000K to 10,000K. in 100 steps).
RGB Lift
Press and to select the parameter to be adjusted.
Press and to adjust the slider.
RGB Gain
Press and to select the parameter to be adjusted.
Press and to adjust the slider.
Component Type
Press and to select Component Type.
Press and to select from:
RGB
YPrPb
•
•
•
•
•
Colour menu continued
Page 83
Rev C April 2011 Page 4.33
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
The Trim submenu is available
only if Global Colour Mode is
selected.
Colour Menu
Trim
Read the notes on Colour and
Global Colourimetry earlier
in this section before making
any settings in the Colour
menus.
Trim
Press and to select Trim.
Press to open the Trim submenu.
Trim rGB Lift and Gain
Press and to select the parameter to be adjusted.
Press and to adjust the slider (-128 to +127).
Global Colourimetry
This is a shortcut to the Global Colourimetry submenu, described later in this
section, in Setup Menu.
Press
and to select Global Colourimetry.
Press to open the Global Colourimetry submenu.
•
•
•
Colour menu continued
Page 84
Page 4.34 Rev C April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
When using the menus, press
OSD or to hide or
reveal the On-Screen-Display.
Setup Menu
Setup menu
To return to the main menu, press up to three times.
From the main menu:
Press
and until Setup is highlighted.
Press to open the Setup menu. The blue highlight moves to the first item in
the menu.
•
Page 85
Rev C April 2011 Page 4.35
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Projector Setup
Press and to select Projector.
Press to open the Projector submenu.
Orientation
Press and to select Orientation.
Press and to select from:
Desktop Front
Desktop Rear
Ceiling Front
Ceiling Rear
Control panel Backlight
Press and to select Backlight.
Press and to select from:
On
Off
•
•
•
Setup menu, continued
Notes
Setup Menu
Projector Setup
A Component Video Sync
setting was available in earlier
models, but for the Component
input only.
In later models, the sync type is
detected automatically.
Page 86
Page 4.36 Rev C April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
Keystone adjustment can be
found in both the Geometry and
Projector Setup menus.
The Keystone adjustment is
NOT available for Input 8.
The range of adjustment will
be dependent on the input
resolution.
Some computer graphics cards
do not recognise the EDID
Extension block.
If you are having problems
booting a computer connected
to the projector:
turn the computer OFF
set DVI EDID Extension Block
to Disable
turn the computer back ON
again
•
•
•
Keystone
Used to correct for distortion caused by the projector being mounted higher or lower
than the screen.
Press
and to select Keystone.
Press and to adjust the slider.
DVI EDID Extension Block
Press and to select DVI EDID Extension Block.
Press and to select from:
Enable
Disable
•
•
Setup menu, projector Setup continued
Page 87
Rev C April 2011 Page 4.37
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Test Patterns
Press and to select Test Patterns.
Press to open the Test Patterns submenu.
Press and to select from:
Off
Alignment Grid
Screen Layout
(shows outlines of various aspect ratios)
Chequerboard
Colour Bars
0% Field
(black)
ColorMAX Calibration
100% Field (Corrected White)
(white, affected by colour settings)
100% Field (Peak White) (white, unaffected by colour settings)
Press
to display the test pattern.
•
Notes
Setup Menu
Projector Setup
Test Pattern
The only test pattern available
for Input 8 is:
100% Field (Corrected White).
WUXGA models only:
Only the Corrected White test
pattern on Input 8 will fill the
full height of the DMD, using all
1200 pixels. All other patterns
will be 1080 pixels high.
Setup menu, projector Setup continued
Page 88
Page 4.38 Rev C April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Setup menu, projector Setup continued
FastFrame
Used to reduce the artifacts and image blur typically associated with rapidly moving
images, by increasing the time the display is blanked between frames (dark time).
From the Projector Setup menu, press
and to select FastFrame.
Press to open the FastFrame submenu.
FastFrame On/Off
Press and to select Fastfame.
Press and to select from:
On
Off
Dark Time
Press and to select Dark Time.
Press and to adjust the slider.
•
•
•
•
Notes
Setup Menu
Projector Setup
FastFrame
If FastFrame is turned on, then
turning on 3D Enable will turn it
off.
When 3D Enable is on, it is not
possible to turn on FastFrame.
The optimum dark time setting
for a 60Hz frame rate is
approximately 8 to 10mS.
Page 89
Rev C April 2011 Page 4.39
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
Setup Menu
Projector Setup
Edge Blend
Setup Menu
Projector Setup
Edge Blend
Active Edges
Edge Blend
Used to improve the appearance of multi-projector displays, by blending overlapping
edges to present a seamless image.
Examples
From the Projector Setup menu, press and to select Edge Blend
Press to open the Edge Blend Setup submenu.
Active Edges
Press and to select Active Edges.
Press to open the Active Edges submenu.
Press and to select the edges to be blended.
For each edge, press and to select from:
On
Off
•
•
•
•
Setup menu, projector Setup continued
Four projectors, two active edges eachTwo projectors, one active edge each
Page 90
Page 4.40 Rev C April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
The actual blend will be
smoother than that shown here.
Edges that have not been
selected as Active, will be
greyed out.
To see the effect of the
adjustment, turn the Overlap
Markers ON..
Input 8 is pixel-mapped directly
to the DMDs, so the image may
be smaller than full-screen.
Input 8 DVI 3D Resolution
should normally be set to
Automatic. However, if the
incoming video signal is nonstandard, the projector may not
be able to select an appropriate
input size.
In this case, set the resolution
to one of the settings provided.
(Settings larger than the DMD
will not available, depending on
model.)
This setting will have no effect
on Inputs 1–7.
Overlap markers
The markers show the extent of the overlap, and can be used as an alignment guide
when adjusting the position of the images.
Press
and to select Overlap Markers.
Press and to select from:
On
Off
Overlap adjust
Used to determine the size of the overlap.
Press
and to select the edge to be blended.
For each edge, press and to adjust the slider (0 to 511).
Input 8 DVI 3D resolution
Press and to select Input 8 DVI 3D Resolution.
Press and to select from:
Automatic
HD2
1280 x 720
SXGA 1280 x 1024
SX+ 1400 x 1050
1080p 1920 x 1080
UXGA 1600 x 1200
WUXGA 1920 x 1200
•
•
•
•
Setup menu, projector Setup, Edge Blend continued
Page 91
Rev C April 2011 Page 4.41
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Black Level Uplift
As it is not possible for any projector to produce an absolute black, any ‘black’ areas
in the overlapped edges may appear slightly less dark than those in the rest of the
image.
Black Level Uplift can be used to counteract this effect, by raising the black level
of the rest of the image. The amount of uplift required will be either x2 or x4,
depending on how many images are overlapped, as shown in the examples below.
Examples
From the Edge Blend menu, press and to select Black Level Uplift.
Press to open the Black Level Uplift Setup submenu.
Uplift Adjustment
Used to determine the amount of uplift.
Press
and to select x2 Region Uplift or x4 Region Uplift.
For each region, press and to adjust the slider (0 to 340).
•
•
•
Setup menu, projector Setup, Edge Blend continued
Notes
Setup Menu
Projector Setup
Edge Blend
Black Level Uplift Setup
This adjustment affects the
amount of Black Level Uplift,
not the size of the region.
Four projectors, with four x2 uplift
regions and four x4 uplift regions
Two projectors, with two x2 uplift
regions
x2 x2
x4 x4
x4 x4
x2
x2
x2x2
no uplift
no uplift
Page 92
Page 4.42 Rev C April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
To adjust Manually:
Working on one projector at a
time, display a test pattern of
0% Field (black), set all four
border adjustments to zero,
then increase the size of each,
until the border disappears.
Non-Addressable Border
Around the edge of the DMD is a border of non-addressable ‘always off’ pixels.
Although ‘always off’, a small amount of stray light from these pixels can cause a
faint border around the projector image.
A small black level adjustment can be applied to remove this border.
Press
and to select Non-Addressable Border.
Press and to select from:
Automatic (recommended)
Manual
Border Adjustment
Press and to select the edge that is to be adjusted.
For each edge, press and to adjust the slider (0 to 255).
•
•
Setup menu, projector Setup, Edge Blend continued
Page 93
Rev C April 2011 Page 4.43
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
Setup Menu
Global Colourimetry
Some menu items may be
greyed out - unavailable due to
the effect of settings made in
other menus, or due to the type
of input signal.
Read these notes on Colour
and Global Colourimetry
before making any settings in
the Colour menus.
Note that any changes made in
the Global Colourimetry menu
will affect ALL inputs, modes
and presets for which Global
Mode has been selected in
the Colour menu (see Colour
Menu, earlier in this section).
Global Colourimetry
Press and to select Global Colourimetry.
Press to open the Global Colourimetry submenu.
•
•
Setup menu continued
Notes on Colour and Global Colourimetry
Global Colourimetry menu (see this section)
After a calibration check on the projector or venue, a set of Global colour settings
can be made in the Global Colourimetry menu. These settings are then available
to be copied at any time using the Colour Mode setting in the Colour menu, or
used as a starting point using the Trim feature in the Colour menu.
Colour menu (see earlier in this section).
The settings made in the Colour menu will be automatically saved in the Mode
History, or can be manually saved to one of the Input Presets (see Input modes
and settings earlier in this section).
The selections available in Colour Mode in the Colour menu are:
Global
Copies the settings made in the Global Colourimetry menu
Temperature Set the colour temperature using the slider
User Set the Red, Green and Blue Lift and Gain using the sliders
Peak Preset high brightness setting
Video, Film,
Graphic
Applies the factory set P7 settings
ColorMAX User Applies the User gamma settings made externally using the
DP Userware on a personal computer
Page 94
Page 4.44 Rev C April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
Read the notes on Colour and
Global Colourimetry earlier
in this section before making
any settings in the Colour
menus.
Note that any changes made in
the Global Colourimetry menu
will affect ALL inputs, modes
and presets for which Global
Mode has been selected in
the Colour menu (see Colour
Menu, earlier in this section).
The Colour Temperature
slider is available only if
Temperature Mode is selected.
The RGB Lift and Gain sliders
are available only if User Mode
is selected.
Colour Mode
Press and to select Colour Mode.
Press and to select from:
Temperature
User
Peak
Video
Film
Graphic
ColorMAX User 1
ColorMAX User 2
Colour Temperature
Press and to select Temperature.
Press and to adjust the slider (3,000K to 10,000K. in 100 steps).
rGB Lift
Press and to select the parameter to be adjusted.
Press and to adjust the slider.
rGB Gain
Press and to select the parameter to be adjusted.
Press and to adjust the slider.
•
•
•
•
Setup menu, Global Colourimetry continued
Page 95
Rev C April 2011 Page 4.45
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Lamp Setup
Press and to select Lamp.
Press to open the Lamp submenu.
The middle row shows the current lamp setting.
Change Lamp Setting
Press and to select Change Lamp Setting.
Press to open the Lamp Setting control box.
single lamp models
dual lamp models
•
•
Setup menu, continued
Notes
Setup Menu
Lamp
Lightning projectors have only
one lamp.
Titan projectors may have one
or two lamps.
continued
Page 96
Page 4.46 Rev C April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Lamp power
Press and to select the Lamp Power setting.
Press and to adjust the Lamp Power from:
80 to 100% in 1% steps
Lamp Mode
Press and to select Lamp Mode.
Press and to select from:
single lamp modes
Lamp 1
lamp 1 only
Lamp 2 lamp 2 only
Alternate on power up, selects the lamp with the least hours used
dual lamp mode
Lamps 1 and 2
both lamps
After setting the Power and Mode, press and to select from
OK
Press to apply the new settings.
or Cancel
Press or to exit without applying the new settings.
The indicators on the control panel will show as follows:
Lamp 1
off = OFF
flashing red = LAMP ERROR green = ON (100%) amber = (80 - 99%)
flashing green = LAMP WARM-UP flashing amber = COOL-DOWN
Lamp 2
off = OFF
flashing red = LAMP ERROR green = ON (100%) amber = (80 - 99%)
flashing green = LAMP WARM-UP flashing amber = COOL-DOWN
•
•
•
Setup menu, Lamp Setup continued
Notes
Lamp Mode applies to Titan
projectors only:
For Dual lamp models in single
lamp mode:
- if the running lamp fails, the
other lamp will automatically be
switched on.
The Lamp 2 and Alternate
settings apply to Dual lamp
models only.
The selected lamp mode:
- will not be applied until OK is
selected
- will be applied gradually over a
period of 30 seconds
- will not be applied until the end
of any warm-up or cool-down
period that has already started.
The Lamp 2 indicator applies
only to Titan Dual models.
Lightning projectors have only
one lamp.
Page 97
Rev C April 2011 Page 4.47
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
Setup Menu
On Screen Display
The On Screen Display will
move to the centre of the DMD
when Blanking is turned On.
(see Geometry menu, earlier in
this section).
If a menu is opened, and no
other key is pressed within the
period set in the OSD Timeout
menu, then the menus will
disappear. When the
key
is pressed again, the menus will
reopen at the same point they
were last viewed.
On Screen Display
Press and to select On Screen Display.
Press to open the On Screen Display submenu.
OSD position
Press and to select OSD Position
Press and to select from:
Upper Left
Upper Centre
Upper Right
Middle Left
Middle Centre
Middle Right
Lower Left
Lower Centre
Lower Right
OSD Size
Press and to select OSD Size.
Press and to select from:
Large
Small
OSD Timeout
Press and to select the length of the On Screen Display Timeout.
Press and to select from:
0 to 255 in 1 second steps (when set to zero, the OSD never times out)
•
•
•
•
Setup menu continued
Page 98
Page 4.48 Rev C April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Password
Entry to the password protected area is available to authorised service personel
only.
Press
and to select Password.
Press to open the Password control box.
Press and to select each digit in turn.
Press and to adjust the digit from:
0 to 9
then move to the next digit.
Use and to select from
OK
Press to enter the password controlled area.
or Cancel
Press or to exit without applying the password.
•
•
Notes
Setup menu continued
Page 99
Rev C April 2011 Page 4.49
Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual 4. Controlling the projector
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
Setup Menu
Comunication
When fresh batteries are
inserted in the remote control,
it will default to address 00.
Remote control 00 is a master
control, able to control all
projectors.
If two or more projectors are set
to the same address, they can
be controlled from one remote
control, provided they are
connected by cable or in range
of the infra red.
Communication Setup
Press and to select Comunication.
Press to open the Comunication submenu.
Serial port Baud rate
Press and to select Serial Port Baud Rate
Press and to select from:
19200
9600
projector Address
The projector and the remote control need to be set to matching addresses. Read
the note to the right on this page, and follow the instructions in the order shown
below:
1
Set the projector address:
Press to open the Projector Address control box.
Press and to select the address setting.
Press and to adjust the address from:
00 to 99
Use and to select from
Apply
Press to apply the new Projector Address.
or Cancel
Press or to exit without making the change.
2 Set the remote control address as shown in Using the control keys, earlier in
this section.
•
•
Setup menu continued
Page 100
Page 4.50 Rev C April 2011
4. Controlling the projector Digital Projection TITAN sx+ 3D, Dual 3D, Ultra Contrast User Manual
For important information about how Input 8 is used, see
INPUT 8
in the Notes column, and also Section 4, Overview.
Notes
Setup Menu
Network
Some items may be greyed out
or not editable, due to the effect
of other settings made in the
Network submenu.
For example, if a Wired
Connection is selected:
Wifi, Channel and SSID will be
unavailable.
Setup menu continued
Network Setup
Press and to select Network.
Press to open the Network submenu.
LAN MAC Address
Projector’s unique ID - for information only - cannot be changed.
Connection
Press and to select Connection
Press to open the Connection control box.
Press and to select from:
Wired
Wireless
Press to apply the new Connection setting.
or Cancel
Press or to exit without making the change.
•
•
•
Loading...