DeWalt DWE7480 User Manual

0 (0)

IF YOU SHOULD EXPERIENCE A PROBLEM WITH YOUR DEWALT PURCHASE,

Before returning this product call

1-800-4-DEWAL T

Questions? Visit us at www.dewalt.com

Des questions ? Rendez nous visite à www.dewalt.com

¿Tiene preguntas? Visítenos en www.dewalt.com

INSTRUCTION MANUAL GUIDE D’UTILISATION MANUAL DE INSTRUCCIONES

IN MOST CASES, A DEWALT REPRESENTATIVE CAN RESOLVE

IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL.

YOUR FEEDBACK IS VITAL TO THE SUCCESS OF D

CALL 1-800-4-DEWALT

YOUR PROBLEM OVER THE PHONE.

IMPROVEMENT PROGRAM.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

WALT’S QUALITY

DWE7480 Heavy-Duty 10" (254 mm) Compact Job Site Table Saw Scie de table de chantier, compacte et industrielle de 254mm (10po) Sierra de banco compacta para el lugar de trabajo de 254 mm (10pulg.)

de alta resistencia

Deﬁ nitions: Safety Guidelines

The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

English

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result

in minor or moderate injury. NOTICE: Indicates a practice not related to personal injury which, if not avoided, may

result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-D

EWALT (1-800-433-9258).

General Safety Rules

WARNING: Read all instructions before operating product. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

SAVE THESE INSTRUCTIONS

WARNING: FOLLOW ALL WIRING CODES and recommended electrical connections to

prevent shock or electrocution.

Double Insulation

If saw is of double-insulated construction, read the following instructions.

This symbol constructed throughout with two separate layers of electrical insulation or one double thickness of insulation between you and the tool’s electrical system. Tools built with this insulation system are not intended to be grounded. As a result, your tool is equipped with a two prong plug which permits you to use extension cords without concern for maintaining a ground connection. Repair or replace damaged or worn cord immediately

NOTE: Double insulation does not take the place of normal safety precautions when operating this tool. The insulation system is for added protection against injury resulting from a possible electrical insulation failure within the tool.

POLARIZED PLUGS

To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

represents double insulated construction. Double insulated tools are

Important Safety Instructions

• TO REDUCE THE RISK OF KICKBACK AND OTHER INJURIES, use all components

of the guarding system (blade guard assembly, riving knife and anti-kickback) for every operation for which they can be used including all through cutting.

• REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that

keys and adjusting wrenches are removed from spindle before turning tool on. Tools, scrap pieces, and other debris can be thrown at high speed, causing injury.

• KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

• DO NOT USE THE MACHINE IN A DANGEROUS ENVIRONMENT. The use of power

tools in damp or wet locations or in rain can cause shock or electrocution. Keep your work area well-lit to avoid tripping or placing arms, hands, and fingers in danger.

• KEEP CHILDREN AWAY. All visitors should be kept at a safe distance from work area.

Your shop is a potentially dangerous environment.

• MAKE WORKSHOP CHILDPROOF with padlocks, master switches, or by removing

starter keys. The unauthorized start-up of a machine by a child or visitor may result in injury.

• DO NOT FORCE TOOL. It will do the job better and be safer at the rate for which it was

designed.

• USE THE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not

designed. Using the incorrect tool or attachment may result in personal injury.

• USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition.

If your product is equipped with a cord set, use only three-wire extension cords that have three-prong grounding-type plugs and three-pole receptacles that accept the tool’s plug. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

MINIMUM GAGE FOR CORD SETS

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150 240V 0-50 51-100 101-200 201-300

Ampere Rating

More Not more AWG Than Than

0 - 6 18 16 16 14 6 - 10 18 16 14 12 10 - 12 16 16 14 12 12 - 16 14 12 Not Recommended

• WEAR PROPER APPAREL. No loose clothing, gloves, neckties, rings, bracelets, or other

jewelry to get caught in moving parts. Non-slip footwear is recommended. Wear protective hair covering to contain long hair. Air vents may cover moving parts and should also be avoided.

• SECURE WORK. Use clamps to hold work when practical (such as when cutting a zero

clearance insert/throat plate). It's safer than using your hand and it frees both hands to operate tool.

• ALWAYS USE SAFETY GLASSES. Everyday eyeglasses are NOT safety glasses. Also

use face or dust mask if cutting operation is dusty. All users and bystanders MUST ALWAYS wear certified safety equipment:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

• DO NOT OVERREACH. Keep proper footing and balance at all times. Loss of balance

may cause personal injury. Do not attempt to retrieve materials near the blade on the saw table while the blade is spinning.

• MAINTAIN TOOLS WITH CARE. Keep blades sharp and clean for best and safest

performance. Follow instructions for lubricating and changing accessories. Poorly maintained blades and machines can further damage the blade or machine and/or cause injury.

• TURN THE MACHINE “OFF”, AND DISCONNECT THE MACHINE FROM THE POWER SOURCE before installing or removing accessories, before adjusting or

changing set-ups, when making repairs or changing locations. Do not touch the plug’s metal prongs when unplugging or plugging in the cord. An accidental start-up can cause injury.

• REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure that the switch is in the “OFF” position before plugging in the power cord. In the event of a power failure, move the switch to the “OFF” position. An accidental start-up can cause injury.

• Do not plug into or unplug from power source with wet hands.

• USE RECOMMENDED ACCESSORIES. Use only accessories that are recommended

by the manufacturer for your model. Accessories that may be suitable for one tool may be hazardous when used on another tool. Consult the instruction manual for recommended accessories. The use of improper accessories may cause risk of injury to persons.

• Magnetic accessories will not work on this saw.

• NEVER STAND OR SIT ON TOOL. Serious injury could occur if the tool is tipped or if the

cutting tool is unintentionally contacted.

• CHECK FOR DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function—check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced. Do not use tool if switch does not turn it on and off. Damaged parts can cause further damage to the machine and/or personal injury.

• DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the blade or cutter only. No cove cutting or freehand cuts.

• Check for adequate outfeed distance behind the saw to be sure materials can pass unobstructed through the cut. Work support tables should be placed in proper locations to fully support the material.

• NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave tool until it comes to a complete stop. Serious injury can result.

• DO NOT OPERATE ELECTRIC TOOLS NEAR FLAMMABLE LIQUIDS OR IN GASEOUS OR EXPLOSIVE ATMOSPHERES. Motors and switches in these tools may

spark and ignite fumes.

• STAY ALERT, WATCH WHAT YOU ARE DOING, AND USE COMMON SENSE. DO NOT USE THE MACHINE WHEN YOU ARE TIRED OR UNDER THE INFLUENCE OF DRUGS, ALCOHOL, OR MEDICATION. A moment of inattention while operating power

tools may result in serious injury.

• DO NOT ALLOW FAMILIARITY (gained from frequent use of this saw) TO REPLACE SAFETY RULES. Always remember that a careless fraction of a second is

sufficient to inflict severe injury. Use extra caution and stay alert when making repetitive cuts. Turn off saw frequently to clean up saw dust and check adjustments to reduce monotony.

Additional Safety Rules for Table Saws

WARNING: ALWAYS USE SAFETY GLASSES. Everyday eyeglasses are NOT safety

glasses. Also use face or dust mask if cutting operation is dusty. All users and bystanders MUST ALWAYS wear certified safety equipment:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Do not expose to rain or use in damp locations.

• AVOID AWKWARD POSITIONS, where a sudden slip could cause a hand to move into a saw blade.

• NEVER REACH IN BACK OF, OR AROUND, THE CUTTING TOOL with either hand to hold down the workpiece.

• KEEP ARMS, HANDS AND FINGERS AWAY from the blade to prevent serious injury.

• USE A PUSH STICK THAT IS APPROPRIATE TO THE APPLICATION TO PUSH WORKPIECES THROUGH THE SAW. A push stick is a wooden or plastic stick, often homemade, that should be used whenever the size or shape of the workpiece would cause you to place your hands within 6" (152mm) of the blade.

• USE HOLD-DOWNS, JIGS, FIXTURES OR FEATHER BOARDS TO HELP GUIDE AND CONTROL THE WORKPIECE. Accessories for use with your tool are available at extra cost from your local dealer or authorized service center. Instructions for making a push stick, a narrow rip auxiliary fence, a push block and feather boards are included in this manual.

• DO NOT PERFORM RIPPING, CROSSCUTTING OR ANY OTHER OPERATION FREEHAND.

• NEVER reach around or over saw blade.

• STABILITY. Make sure the table saw is firmly mounted to a secure surface before use and does not move.

• NEVER CUT METALS, CEMENT BOARD OR MASONRY. Certain man-made materials have special instructions for cutting on table saws. Follow the manufacturer’s recommendations at all times. Damage to the saw and personal injury may result.

• THE PROPER THROAT PLATE MUST BE LOCKED IN PLACE AT ALL TIMES to reduce the risk of a thrown workpiece and possible injury.

• USE THE CORRECT SAW BLADE FOR THE INTENDED OPERATION. The blade must rotate toward the front of the saw. Always tighten the blade arbor nut securely. Before use, inspect the blade for cracks or missing teeth. Do not use a damaged or dull blade.

• NEVER ATTEMPT TO FREE A STALLED SAW BLADE WITHOUT FIRST TURNING

THE MACHINE OFF AND DISCONNECTING THE SAW FROM THE POWER SOURCE. If a workpiece or cut-off piece becomes trapped inside the blade guard

assembly, turn saw off and wait for blade to stop before lifting the blade guard assembly and removing the piece.

• NEVER START THE MACHINE with the workpiece against the blade to reduce the risk of a thrown workpiece and personal injury.

• DO NOT HAVE ANY PART OF YOUR BODY IN LINE WITH THE BLADE. Personal injury may occur. Stand to either side of the blade.

• NEVER PERFORM LAYOUT, ASSEMBLY OR SET-UP WORK on the table/work area when the machine is running. A sudden slip could cause a hand to move into the blade. Severe injury can result.

• CLEAN THE TABLE/WORK AREA BEFORE LEAVING THE MACHINE. Lock the switch in the “OFF” position and disconnect from the power source to prevent unauthorized use.

• ALWAYS lock the fence and bevel adjustment before cutting.

• DO NOT leave a long board (or other workpiece) unsupported so the spring of the board causes it to shift on the table resulting in loss of control and possible injury. Provide proper support for the workpiece, based on its size and the type of operation to be performed. Hold the work firmly against the fence and down against the table surface.

• IF THIS SAW makes an unfamiliar noise or if it vibrates excessively, cease operating immediately, turn unit off and disconnect from power source until the problem has been located and corrected. Contact a D service center or other qualified service personnel if the problem cannot be found.

• USE RECOMMENDED ACCESSORIES. The use of improper accessories may cause risk of personal injury.

• DO NOT OPERATE THIS MACHINE until it is completely assembled and installed according to the instructions. A machine incorrectly assembled can cause serious injury.

EWALT factory service center, a DEWALT authorized

English

• OBTAIN ADVICE from your supervisor, instructor, or another qualified person if you are not

thoroughly familiar with the operation of this machine. Knowledge is safety.

• ADDITIONAL INFORMATION regarding the safe and proper operation of power tools

(i.e., a safety video) is available from the Power Tool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851 (www.powertoolinstitute.com). Information is also available from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201. Please refer to the U.S. Department of Labor OSHA 1910.213 Regulations.

English

TERMS: THE FOLLOWING TERMS WILL BE USED THROUGHOUT THE MANUAL AND YOU SHOULD BECOME FAMILIAR WITH THEM.

• Thru sawing refers to any cut that completely cuts through the workpiece.

• Non-thru sawing refers to any cut that does not completely cut through the workpiece.

• Push Stick refers to a wooden or plastic stick, usually homemade, that is used to push

small workpiece through the saw and keeps the operator’s hands clear of the blade.

• Kickback occurs when the saw blade binds in the cut and violently thrusts the workpiece

back toward the operator.

• Freehand refers to cutting without the use of a miter gauge or rip fence or any

other means of guiding or holding the workpiece other than the operator’s hand.

WARNING: Never perform freehand cutting with this saw.

• Plunge cutting refers to cutting where the workpiece is either lowered down onto the

blade with the workpiece controlled by the user's hands or the workpiece is supported by the user's hands on the table surface and the blade is then raised up through the workpiece.

WARNING: Never perform plunge cutting with this saw.

• Resawing - Flipping material to make a cut the saw is not capable of making in one pass. WARNING: Resawing IS NOT recommended.

• Outfeed - the distance behind the saw required to pass the material all the way through

the cut.

SAW BLADE GUARD ASSEMBLY, ANTI-KICKBACK ASSEMBLY AND RIVING KNIFE

Your table saw is equipped with a blade guard assembly, anti-kickback assembly and riving knife that covers the blade and reduces the possibility of accidental blade contact. The riving knife is a flat plate that fits into the cut made by the saw blade and effectively fights kickback by lessening the tendency of the blade to bind in the cut. The blade guard assembly and anti-

kickback assembly can only be used when making thru cuts that sever the wood. When making rabbets and other cuts that make non-thru cuts, the blade guard assembly and anti-kickback assembly must be removed and riving knife lowered to the non through cut position marked on the riving knife. Two anti-kickback pawls are

located on the sides of the riving knife that allow the wood to pass through the blade in the cutting direction but reduce the possibility of the material being thrown backwards toward the operator.

Use all components of the guarding system (blade guard assembly, riving knife and anti-kickback assembly) for every operation for which they can be used including all thru cutting. If you elect not to use any of these components for a particular application exercise additional caution regarding control of the workpiece, the use of push sticks, the position of your hands relative to the blade, the use of safety glasses, the means to avoid kickback and all other warnings contained in this manual and on the saw itself. Replace the guarding systems as soon as you return to thru cutting operations. Keep the guard assembly in working order.

MAKING A PUSH STICK (Inside Back Cover)

• In order to operate your table saw safely, you must use a push stick whenever the size or

shape of the workpiece would cause your hands to be within 6" (152mm) of the saw blade or other cutter. A push stick is included with this saw.

• No special wood is needed to make additional push sticks as long as it’s sturdy and long enough. A length of 15.7" (400mm) is recommended with a notch that fits against the edge of the workpiece to prevent slipping. It’s a good idea to have several push sticks of the same length [15.7" (400 mm)] with different size notches for different workpiece thicknesses.

• See the inside back cover for a picture of a push stick. The shape can vary to suit your own needs as long as it performs its intended function of keeping your hands away from the blade.

KICKBACKS

Kickbacks can cause serious injury. A kickback occurs when a part of the workpiece binds between the saw blade and the rip fence, or other fixed object, and rises from the table and is thrown toward the operator. Kickbacks can be avoided by attention to the following conditions.

How to Avoid Them and Protect Yourself from Possible Injury

a. Be certain that the rip fence is parallel to the saw blade. b. Do not rip by applying the feed force to the section of the workpiece that will become

the cut-off (free) piece. Feed force when ripping should always be applied between the saw blade and the fence; use a push stick for narrow work, 6" (152mm) wide or less.

c. Keep saw blade guard assembly, riving knife and anti-kickback assembly in place and

operating properly. If anti-kickback assembly is not operational, return your unit to the nearest authorized D alignment with the saw blade and the anti-kickback assembly must stop a kickback once it has started. Check their action before ripping by pushing the wood under the anti-kickback assembly. The teeth must prevent the wood from being pulled toward the front of the saw.

d. Plastic and composite (like laminate flooring) materials may be cut on this saw. However,

since these are usually quite hard and slippery, the anti-kickback pawls may not stop a kickback. Therefore, be especially attentive to following proper set up and cutting procedures for ripping.

e. Use saw blade guard assembly, anti-kickback assembly and riving knife for every

operation for which it can be used, including all thru sawing.

f. Push the workpiece past the saw blade prior to release. g. NEVER rip a workpiece that is twisted or warped, or does not have a straight edge to

guide along the fence.

h. NEVER saw a large workpiece that cannot be controlled. i. NEVER use the fence as a guide or length stop when crosscutting. j. NEVER saw a workpiece with loose knots, flaws, nails or other foreign objects. k. NEVER rip a workpiece shorter than 10" (254mm). l. NEVER use a dull blade – replace or have resharpened.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well-ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes or lay on the skin

may promote absorption of harmful chemicals.

EWALT service center for repair. The riving knife must be in

WARNING: Use of this tool can generate and/or disburse dust, which may cause

serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body. Always operate tool in well-ventilated area and provide for proper dust removal. Use dust collection system wherever possible.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

Speciﬁ cations

Amperes 15 A Miter Angle 60° L and R Bevel Angle -2° to 45° L Blade Size 10" (254 mm) Max. Cut Depth 0° Bevel 3-1/8" (79 mm) Max. Cut Depth 45° Bevel 2-1/4" (57 mm) RPM, no load 4800

Unpacking

WARNING: To reduce the risk of injury, DO NOT connect the machine to the power source

until the table saw is completely assembled and you read the entire instruction manual.

Open the box and slide the saw out, as shown in Figure 1. Carefully unpack the table saw and all loose items from the carton. Examine all parts to make sure that parts have not been damaged during shipping. If any parts are missing or damaged, contact your dealer to replace them before attempting to assemble the tool.

Refer to Figure 2 for the loose items and hardware included with the saw:

1. Rip fence

2. Arbor wrench and spindle wrench (attached to saw base)

3. Blade guard assembly

4. Miter gauge

5. Push stick (attached to rip fence)

WARNING: To reduce the risk of serious personal injury, have push stick ready to

use before starting cut.

FIG. 1 FIG. 2

FEATURES (Fig. 3)

Examine Figure 3 to become familiar with the saw and its various parts. The following sections on assembly and adjustments will refer to these terms and you must know what and where the parts are.

FIG. 3

English

A. Table B. Miter gauge C. Blade D. Blade guard assembly E. Fence F. Fence rails G. Rip fence front/rear latch

English

H. Fine adjustment knob I. Blade height adjustment wheel J. Bevel lock lever K. ON/OFF switch L. Rip fence indicator

M. Adjustable feet N. Mounting holes O. Cord wrap P. Handle Q. Anti-kickback assembly R. Rip fence locator pins S. Dust collection port T. Dust shroud U. Push stick V. Arbor wrench, spindle wrench W. Rail lock lever

ASSEMBLY

WARNING: Shock Hazard. To reduce the risk of serious personal injury, turn unit off and disconnect machine from power source before attempting to move it, change accessories or make any adjustments.

ASSEMBLE YOUR SAW IN THE FOLLOWING ORDER

1. Rip fence (NOTE: Adjust rip scale before proceeding; refer to Rip Scale Adjustment

under Adjustment.)

2. Position riving knife

3. Anti-kickback assembly

4. Blade guard assembly

5. Miter gauge (if required for application)

NOTE: No tools needed for assembly. NOTE: Wrenches included with this saw are to remove and replace blades.

Assembling the Rip Fence (Fig. 3–5)

The rip fence can be installed in two positions on the right (Position 1 for 0" to 20" ripping, and Position 2 for 4" to 24" ripping) and one position on the left of your table saw.

1. Align the locator pin (R) on the fence rail with the fence head slot and align the latch (G)

with the opening (AA).

2. Secure the rip fence by snapping the latches onto the rails as shown in Figure 5. Be sure

to snap both front and rear latches (G) in place.

FIG. 4

FIG. 5

To Remove the Throat Plate (Fig. 6)

1. Remove the throat plate (X) by turning the cam lock knob (CC) 1/4 turn counterclockwise.

2. Using finger hole (XX) on the plate, pull throat plate up and forward to expose the inside of

the saw.

FIG. 6

FIG. 7

Positioning the Riving Knife (Fig. 7–9)

1. Raise the saw blade arbor to its maximum height.

2. Loosen the riving knife lock knob (YY) (minimum of three turns).

3. To disengage riving knife lock pin, push lock knob toward the riving knife as indicated by the yellow arrows on the knob.

FIG. 8

4. Lift and slide the riving knife to the approximate position indicated by the markings (non-thru and thru-position) on the riving knife and the lock pin will snap into place.

5. Tighten the riving knife lock knob.

WARNING: Before connecting the table saw to the power source or operating the saw,

always inspect the blade guard assembly and riving knife for proper alignment and clearance with saw blade. Check alignment after each change of bevel angle.

NOTE: DO NOT operate saw if riving knife is not locked in the thru cut (ZZ) or non-thru cut position (A1) hole.

When properly aligned, the riving knife will be in line with the blade at both table top level, and at the top of the blade. Using a straight edge, ensure that the blade (C) is aligned with the riving knife (FF) as shown in Figure 9. With power disconnected, operate the blade tilt and height adjustments through the extremes of travel and ensure the blade guard assembly clears the blade in all operations and that the anti-kickback assembly is functioning.

FIG. 9

To Replace the Throat Plate (Fig. 6)

1. Align the throat plate as shown in Figure 6, and insert the tabs on the back of the throat plate into the holes on the back of the table opening.

2. Rotate cam counterclockwise until the front of throat plate drops into place. Secure by rotating cam lock knob (CC) clockwise 1/4 turn (when cam lock is under the table holding the throat plate in place).

3. The throat plate includes four adjustment screws which raise or lower the throat plate. When properly adjusted, the front of the throat plate should be flush or slightly below the surface of the table top and secured in place. The rear of the throat plate should be flush or slightly above the table top.

WARNING: To reduce the risk of serious personal injury, the throat plate must be locked in

place at all times.

Anti-Kickback Assembly (Fig. 10)

WARNING: To reduce the risk of serious personal injury, the anti-kickback assembly must

be in place for all possible cuts.

1. Remove the anti-kickback assembly (Q) from the storage position. Refer to Storage.

2. Locate the anti-kickback mounting hole and slot (EE) at the top of the riving knife (FF).

3. Slide the anti-kickback housing along the top of the riving knife until the stem (GG) locates the slot above the mounting hole. Depress the stem (GG) on the anti-kickback assembly to allow the assembly to drop into the hole (EE). Push down on the anti-kickback assembly until it snaps into place and locks the assembly. NOTE: Pull up on the anti-kickback assembly to ensure it has locked into place.

FIG. 10

Blade Guard Assembly (Fig. 11, 12)

TO ATTACH BLADE GUARD ASSEMBLY

WARNING: To reduce the risk of serious personal injury, the blade guard assembly must be

in place for all possible cuts.

1. While holding the blade guard assembly (D) in a vertical position slide the locating pin (HH) into the riving knife slot (II) centering the riving knife within the v-shaped notch in the top guard. Refer to Figure11.

2. Rotate the blade guard assembly toward the front of the saw while keeping the pin (HH) at the top of the riving knife slot. Rotate until the blade guard assembly is parallel to the table. Refer to Figure12.

3. Press the blade guard lock lever (WW) down until it snaps into the locked position. Check to make sure the guard is locked onto the riving knife. If the guard is not locked the blade guard lock lever will flip up to the unlocked position.

FIG. 11

FIG. 12 FIG. 12A FIG. 12B

TO REMOVE BLADE GUARD ASSEMBLY

1. Lift the blade guard assembly lock lever (WW) to the unlocked position.

2. Rotate the guard back and slide pin from riving knife slot.

Miter Gauge (Fig. 13)

NOTE: A large auxiliary miter gauge face may be used. TO ATTACH THE MITER GAUGE

FIG. 13

The DWE7480 includes a miter gauge (B) for crosscutting materials. The miter gauge can be used by inserting into one of the two miter gauge slots (JJ) in the table top.

NOTE: See crosscutting and bevel crosscutting instructions before performing these operations on the table saw.

Bench Mounting

NOTE: A portable table saw stand is designed for use with this saw and is available at a local D

EWALT dealer or

service center at extra cost.

TO BENCH MOUNT SAW (FIG. 3)

WARNING: To reduce the risk of serious personal injury, turn unit off and disconnect machine from power source before attempting to move it, change accessories or make any adjustments. An accidental start-up can cause injury.

CAUTION: To reduce the risk of personal injury, make sure table saw is firmly mounted

before use.

The table saw must be mounted firmly. Four mounting holes (N, Fig. 3) are provided in the metal frame for mounting. We strongly recommend that these holes be used to anchor the table saw to your workbench or other rigid, stationary work support.

CAUTION: Ensure that the surface is stable enough that large pieces of material will not cause it to tip over during use.

1. Center the saw on the desired, stable work surface.

2. Drive four 3-1/2" (88.9 mm) long screws through the holes in the metal frame. Make sure

the screws extend through the frame and securely attach to the supporting work surface.

If marring the supporting work surface is a concern, the DWE7480 can be mounted to scrap wood which can then be clamped onto the desired work surface.

1. Cut a piece of 3/4" (19 mm) plywood to fit beneath the footprint of the saw.

2. Screw the saw to the plywood and clamp the overhang of the plywood to the work

surface. If the screws protrude through the plywood base, set it on two scrap pieces of material of equal thickness and attach them to the edges of the plywood to hold the saw further off of the work surface and prevent the screws from marring the surface.

English

Connecting Saw to Power Source

WARNING: To reduce the risk of injury, before connecting saw to power source, make

sure the switch is in the OFF position.

Be sure your power supply agrees with the nameplate marking. AC Only means that your saw will operate on alternating current only. A voltage decrease of 10 percent or more will cause a loss of power and overheating. All D operate, check the power supply.

English

On-Off Switch (Fig. 14)

WARNING: To reduce the risk of injury, be sure switch is in the OFF position before

plugging machine in.

Lift the ON/OFF switch (K) paddle up to turn your saw ON and push it down to turn your saw OFF.

A hole (KK) is provided in the switch for insertion of a padlock with a removable shank to lock the saw off.

NOTE: A conventional padlock will not fit.

Rip Fence Operation

RAIL LOCK LEVER (FIG. 15)

The rail lock lever (W) locks the fence in place preventing movement during cutting. To lock the rail lever, push it down and toward the rear of the saw. To unlock, pull it up and toward the front of the saw.

NOTE: When ripping, always lock the rail lock lever. WORK SUPPORT EXTENSION/NARROW RIPPING FENCE (FIG. 15, 16)

The table saw is equipped with a narrow ripping fence that also supports work that extends beyond the saw table.

To use the narrow ripping fence in the work support position, rotate it from its stored position as shown in Figure 16, and slide the pins into the lower sets of slots on both ends of the fence.

To use the narrow ripping fence in the narrow ripping position, snap the pins into the upper sets of slots on both ends of the fence.

This feature will allow 2" (51 mm) of extra clearance to the blade. If more clearance is necessary, follow directions for making an auxiliary fence under Narrow Rip Auxiliary Fence in the Operation section.

FIG. 15

EWALT tools are factory tested. If this tool does not

FIG. 14

FIG. 16

FINE ADJUSTMENT KNOB (FIG. 17)

The fine adjustment knob (H) allows smaller adjustments when setting the fence. Before

FIG. 17

adjusting, be sure the rail lock lever is in its up or unlocked, position.

RIP SCALE POINTER

The rip scale pointer will need to be adjusted for proper performance of the rip fence if the user switches between thick and thin kerf blades. Refer to Adjusting the Rip Scale under Adjustments for alignment instructions.

Adjustments

WARNING: To reduce the risk of injury, turn unit off and disconnect machine from power source before installing and removing accessories, before adjusting or changing set-

ups or when making repairs. An accidental start-up can cause injury.

NOTE: Your saw is fully and accurately adjusted at the factory at the time of manufacture. If readjustment due to shipping and handling or any other reason is required, follow the steps below to adjust your saw.

Once made, these adjustments should remain accurate. Take a little time now to follow these directions carefully to maintain the accuracy of which your saw is capable.

RAIL LOCK ADJUSTMENT (FIG. 3, 18)

(Tightening Fence Clamping System)

1. Lock the rail lock lever (W).

2. On the underside of the saw, loosen the nut (LL).

3. Tighten the hex rod (MM) until the spring on the locking system

is compressed creating the desired tension on the rail lock lever. Retighten the jam nut against the hex rod.

4. Check that the fence does not move when the lock lever is

engaged. If the fence is still loose, tighten the spring further.

ADJUSTING THE RIP SCALE (FIG. 3, 19)

1. Unlock the rail lock lever (W).

2. Set the blade at 0° bevel and move the fence in until it touches the blade.

3. Lock the rail lock lever.

4. Loosen the rip scale indicator screws (NN) and set the rip

scale indicator to read zero (0). Retighten the rip scale indicator screws. NOTE: The yellow rip scale (top) reads correctly only when the fence is mounted on the right side of the blade and is in position 1 (for 0 to 20" ripping, not the 24" rip position). The white scale (bottom) reads correctly only when the fence is mounted on the right side of the blade and in position 2 (for 4" to 24" ripping).

BLADE ALIGNMENT ADJUSTMENT (Blade Parallel to Miter Slot)

WARNING: Cut Hazard. Check the blade at 0˚ and 45˚ to make sure blade does not hit the throat plate, causing personal injury.

FIG. 18

FIG. 19

If the blade appears to be out of alignment with

FIG. 20

the miter slot on the table top, it will require calibration for alignment. To realign the blade and miter slot, use the following procedure:

1. Locate the black hex locator screws (OO) that hold up the trunnion to the bottom of the table in the rear of the saw.

2. Loosen both screws and align the blade with the miter slot. Be sure to measure between the miter slot and the back and front of the blade to ensure parallelism.

3. Snugly tighten the screws to secure the trunnion and blade assembly to the table at the parallel position.

FENCE ALIGNMENT ADJUSTMENT (FIG. 3, 4) (Blade Parallel to Fence)

If you experience fence alignment problems and want to correct an out of parallel between the fence and the blade, be sure to check the alignment of the blade to the miter slot first. After confirming that those elements are aligned, proceed with alignment of the blade to the fence using the following procedure:

1. Unlock the rail lock lever (W) and locate the two fence locator pins (R) that support the fence on the front and rear rails.

2. Loosen the rear locator pin and adjust the position of the fence in the groove on the fence until it sets the fence face parallel to the blade. Make sure you measure from the fence face to the front and back of the blade to ensure alignment.

3. Tighten the locator pins and repeat on the left side of the blade.

4. Check rip scale adjustment.

BEVEL STOP AND POINTER ADJUSTMENT (Calibrating Bevel Scale)

Calibrating the bevel system on the saw may require two separate steps, one for the bevel scale and another for the bevel pointer. The scale should always be checked first followed by adjustments to the red pointer.

BEVEL LOCK ADJUSTMENT (FIG. 21)

The bevel lock lever (J) may need adjustment to maintain lock force. To do this, put the lock lever in the locked position. Use a cross head screwdriver to remove

the screw (PP) holding the lock lever in place (Fig. 21). Remove the lock lever from the locking bolt and place lock lever in the desired position. Insert the screw (PP) and tighten securely.

FIG. 21

Part A – Adjusting the Bevel Scale System (Fig. 22, 23)

1. Remove the blade guard assembly from the saw and raise the blade all the way up in the table.

2. Unlock the bevel lock lever (J) and loosen the bevel stop screw (QQ).

3. Place a square against the table and blade.

NOTE: Be sure to place the square between the teeth on the blade to ensure an accurate

measurement.

4. Adjust the bevel angle until the blade is flat against the square. Lock the bevel lock lever(J).

5. Move the bevel stop cam (RR) until it firmly contacts the trunnion casting. Tighten the bevel stop screw.

6. Repeat procedure at 45˚ using a triangle or speed square.

Part B – Adjusting the Bevel Scale Pointer

NOTE: Complete this step only if Part A has been completed.

7. Check the bevel scale angle. If the pointer does not read 0°, loosen the pointer screw (SS) and move it to the 0° mark on the bevel scale. Retighten the pointer screw.

FIG. 22

FIG. 23

MITER GAUGE ADJUSTMENT (FIG. 24) (Calibrating Miter Gauge Pointer)

Your miter gauge features adjustable stops at 90° and 45° left and right. To adjust the miter gauge, loosen the screw (TT) and move to desired position. Tighten the

screw against the stop plate.

FIG. 24

English

ALIGNING RIVING KNIFE TO BLADE (FIG. 25)

1. Remove the throat plate. Refer to To Remove the Throat Plate under Assembly.

2. Raise the blade to full depth of cut and 0° bevel angle.

3. If needed, raise the riving knife (FF) to the thru cut (ZZ) or highest position. Refer to Positioning the Riving Knife under

FIG. 25

Assembly.

4. Locate the three small set screws (A2) adjacent to the riving knife lock knob (YY). These screws will be used to adjust the riving

English

knife position.

5. Lay a straight edge on the table against two blade tips. The riving knife should not touch the straight edge. If needed, loosen the two larger lock screws (A3).

6. Adjust the small set screws (A2) to move the riving knife according to the position noted in step 5. Lay the straight edge on the opposite side of the blade and repeat adjustments as needed.

7. Lightly tighten the two larger lock screws (A3).

8. Place a square flat against the riving knife to the verify riving knife is vertical and in line with the blade.

9. If needed, use the set screws to bring the riving knife vertical with the square.

10. Repeat steps 5 and 6 to verify position of riving knife.

11. Fully tighten the two larger lock screws (A3).

Saw Blades

WARNING: Riving knifes must be matched to saw blade dimensions in order to function

effectively. Refer to Riving Knife Selection.

NOTE: THIS SAW IS INTENDED FOR USE ONLY WITH SAW BLADES 10" (254mm) IN DIAMETER. Refer to Fig. 26. NOTE: This saw is not intended for use with dado blades and molding cutters. Personal injury may occur.

1. The saw blade furnished with your new saw is a 10" (254 mm) combination blade, used for crosscutting (across the grain) and ripping (with the grain) through the material. The center hole to fit on the arbor is 5/8" (16 mm) diameter (.625"). This blade will produce a good quality cut for most applications.

2. There are many types of blades available to do specific and special jobs such as crosscut only, rip only, hollow ground, thin plywood, paneling, etc.

3. Use only saw blades designed for maximum safe operating speeds of 5,000 RPM or greater.

4. Saw blades should always be kept sharp. It is recommended that you locate a reputable sharpening service to sharpen your blades when needed.

CAUTION: Abrasive wheels or blades (including diamond) should not be used on this saw.

FIG. 26

Blade (Fig. 3, 6, 27, 28)

REPLACING THE BLADE

FIG. 27

1. Raise the saw blade arbor to its maximum height by turning the blade height adjustment wheel (I) clockwise.

2. If replacing the blade, remove the blade guard assembly (D) and throat plate (X) prior to installing the new blade. (Refer to To Remove the Blade Guard Assembly and To

Remove the Throat Plate under Assembly.)

NOTE: It may be easier to change

the blade with the saw blade beveled to 0˚.

3. Remove the arbor nut (Y) and outer washer (Z) and set aside.

4. Place the blade (C) on the arbor making sure the teeth of the blade point downward and toward the front of the saw.

5. Place the outer washer (Z) against the blade, raised

FIG. 28

side out and tighten the arbor nut against the washer as far as possible by hand. Ensure that the outer washer and arbor nut are free of dust and debris before installing.

6. To further tighten the arbor nut (Y), use the open ended spindle wrench (supplied) to keep the spindle from rotating.

7. Use the arbor wrench (supplied) to hold the nut and tighten it by turning it clockwise. Reposition the wrench on the arbor nut and repeat as necessary until the nut and washer are securely fastened against the blade).

NOTE: Different types of blades make different kerfs (width of cuts). Therefore, it is necessary to check adjustment of rip scale when changing blades. Replacement blade MUST not exceed the thickness stated on the riving knife. The riving knife provided with the saw is 2.2mm thick.

Riving Knife Selection

WARNING: To minimize the risk of kickback and to ensure proper cutting, the riving knife

must be the proper thickness for the blade used.

The riving knife supplied with this table saw is the correct size for the blade supplied with the saw.

If a different blade is used check the blade body (plate) thickness and the blade kerf (cutting) width marked on the blade or on the blade packaging. The riving knife thickness must be greater than the body thickness and less than the kerf width as shown in Figure 29. If it is not, the riving knife MUST be replaced with one that has the correct thickness.

The riving knife provided with this saw is marked as follows (Fig.30):

0.087" (2.2mm) THICK RIVING KNIFE. ONLY USE FOR 10" (254 mm) Ø BLADE

The riving knife available as an accessory marketed by D

0.110" (2.8 mm) THICK RIVING KNIFE. ONLY USE FOR 10" (254mm) Ø BLADE

WITH 0.094" (2.4 mm) MIN. KERF WIDTH AND 0.067" (1.75 mm) MAX. BODY THICKNESS.

EWALT is marked as follows:

WITH 0.118" (3.0 mm) MIN. KERF WIDTH AND 0.098" (2.5 mm) MAX. BODY THICKNESS

FIG. 29

KERF WIDTH

(WIDTH OF CUT

MADE BY THE

BLADE)

BODY (OR PLATE)

THICKNESS OF THE

BLADE

RIVING KNIFE

THICKNESS

FIG. 30

All DEWALT blade body thickness and kerf widths are provided at www.DEWALT.com. If a different blade is used and the body thickness and kerf width dimensions are not provided,

use the following procedure to determine the correct riving knife thickness:

1. Measure the body thickness of the blade.

FIG. 31

2. Make a shallow cut in scrap material and measure the kerf width.

3. Select the riving knife as shown in Figure 29.

4. Slide the riving knife through the shallow cut made in step 2 to confirm the correct riving knife has been selected. The riving knife should not bind or drag through the cut.

IMPORTANT: If any dragging or binding of the material is encountered as it reaches the riving knife, turn unit off and disconnect machine from power source. Repeat steps 1–4 to make the proper riving knife selection before attempting another cut.

Kickback

Kickback is a dangerous condition! It is caused by the workpiece binding against the blade. The result is that the workpiece can move rapidly in a direction opposite to the feed direction. During kickback, the workpiece could be thrown back at the operator. It can also drag the operator’s hand back into the blade if the operator’s hand is at the rear of the blade. If kickback occurs, turn the saw OFF and verify the proper functioning of the riving knife, anti-kickback assembly and blade guard assembly before resuming work.

WARNING: Refer to Additional Safety Rules for Table Saws and follow all warnings

provided regarding KICKBACK.

OPERATION

WARNING: Before using the saw, verify the following each and every time:

1. ALWAYS wear proper eye, hearing and respiratory equipment.

2. Blade is tight.

3. Bevel angle and height lock knobs are tight.

4. If ripping, ensure fence lock lever is tight and fence is parallel to the blade.

5. If crosscutting, miter gauge knob is tight.

6. The blade guard assembly is properly attached and the anti-kickback assembly is functioning.

7. ALWAYS inspect the blade guard assembly and riving knife for proper alignment, operation and clearance with saw blade.

8. ALWAYS make sure both guards are in the down position in contact with the table before operating.

Failure to adhere to these common safety rules can greatly increase the likelihood of injury.

WARNING: To reduce the risk of injury, turn unit off and disconnect machine from

power source before installing and removing accessories, before adjusting or changing set-

ups or when making repairs. An accidental start-up can cause injury.

WARNING: Before connecting the table saw to the power source or operating the saw,

always inspect the blade guard assembly and riving knife for proper operation alignment and clearance with saw blade. Personal injury may result.

WARNING: Ripping or crosscutting may cause saw to tip over while operating. Make sure

saw is securely mounted to a stable surface.

WARNING: Never use the fence and miter gauge together. This may cause a kickback

condition and injure the operator.

CAUTION: If your saw makes an unfamiliar noise or if it vibrates excessively, cease operating

immediately, turn unit off and disconnect from power source until the problem has been located and corrected. Contact a D

EWALT factory service center, a DEWALT authorized service

center or other qualified service personnel if the problem cannot be found.

CAUTION: The proper throat plate must be in place at all times to reduce the risk of a

thrown workpiece and possible injury.

There are two basic types of cutting with table saws: ripping and crosscutting. Cutting with the grain is ripping and cutting against the grain is crosscutting. With manmade materials, the distinction is made such that ripping is cutting to a different width and crosscutting describes cutting material across the shorter dimension.

WARNING: When ripping, always use the fence to provide a guide for the material and

blade guard assembly against a kickback situation.

WARNING: Never perform any cutting operation freehand. Never perform plunge cutting. CAUTION: When crosscutting, always use the miter gauge.

Guard Operating Feature (Fig. 32)

WARNING: To reduce the risk of injury, turn unit off and disconnect machine from

power source before installing and removing accessories, before adjusting or changing set-

ups or when making repairs. An accidental start-up can cause injury.

1. The guard(s) will lock in place when in the raised position.

2. This feature increases visability when measuring the blade to fence distance.

3. Push down on guard(s) and they will release to the operating position.

• ALWAYS make sure both guards are in the down position in contact with the table before

operating.

FIG. 32

OPERATING

POSITION

RAISED

POSITION

English

Ripping

WARNING: Never touch the free end of the workpiece or a free piece that is cut off, while

the power is ON and/or the saw blade is rotating. Piece may contact the blade resulting in a thrown workpiece and possible injury.

WARNING: A rip fence should ALWAYS be used for ripping operations to prevent loss of

control and personal injury. NEVER perform a ripping operation freehand. ALWAYS lock the fence to the rail.

English

WARNING: When bevel ripping and whenever possible, place the fence on the side of the

blade so that the blade is tilted away from the fence and hands. Keep hands clear of the blade and use a push stick to feed the workpiece if there is less than 6" (152 mm) between the fence and the blade.

1. Lock the rip fence by pressing the rail lock lever down. Remove the miter gauge.

2. Raise the blade so it is about 1/8" (3.2 mm) higher than the top of the workpiece.

3. Hold the workpiece flat on the table and against the fence. Keep the workpiece about 1" (25.4 mm) away from the blade.

CAUTION: The workpiece must have

FIG. 33

straight edge against the fence and must not be warped, twisted or bowed. Keep both hands away from the blade and away from the path of the blade. Refer to proper hand position in Figure 33.

4. Turn the saw on and allow the blade to come up to speed. Both hands can be used in starting the cut. When there i s approximately 12" (305 mm) left to be ripped, use only one hand, with your thumb pushing the material, your index and second finger holding the material down and your other fingers hooked over the fence. Always keep your thumb along side your first two fingers and near the fence.

5. Keeping the workpiece against the table and fence, slowly feed the workpiece rearward all the way through the saw blade. Continue pushing the workpiece until it is clear of the blade guard assembly and it falls off the rear of the table. Do not overload the motor.

6. Never try to pull the workpiece back with the blade turning. Turn the switch off, allow the blade to stop, raise the anti-kickback teeth on each side of the riving knife if necessary and slide the workpiece out.

7. When sawing a long piece of material or a panel, always use a work support. A sawhorse, rollers, or out feed assembly provides adequate support for this purpose. The work support must be at the same height as the saw table.

CAUTION: Never push or hold onto the free or cut off side of the workpiece.

Ripping Small Pieces

It is unsafe to rip small pieces. It is not safe to put your hands close to the blade. Instead, rip a larger piece to obtain the desired piece. When a small width is to be ripped and the hand cannot be safely put between the blade and the rip fence, use one or more push sticks. A pattern is included at the end of this manual to make

FIG. 34

push sticks. A push stick (U) is included with this saw, attached to the rip fence. Use the push stick(s) to hold the workpiece against the table and fence, and push the workpiece fully past the blade. Refer to Figure 34.

NOTE: The table saw is equipped with a narrow ripping fence that also supports work that extends beyond the saw table. Refer to Work Support Extension/Narrow Ripping Fence under Rip Fence Operation.

Narrow Rip Auxiliary Fence (Fig. 35–37)

The narrow rip auxiliary fence should be used for a rip measuring 2" (51mm) or narrower. This fence will allow the guard to remain on the saw when completing narrow ripping. This fence will provide ample space for proper use of a push block (A12, Refer to Push Block).

1. Follow the diagram in Figure 35 to construct the narrow rip auxiliary fence (A13, Fig. 37).

NOTE: A11 should be cut to fit the length of the saw table top and sides (A14) must be parallel.

FIG. 35

1/2"

(12.7 mm)

3/8"

(9.5 mm)

(25 mm)

2. After the narrow rip auxiliary fence is constructed, slip it over the saw table top and place it flush to the fence as shown in Figure 37.

3. Feed the workpiece through until the edge of the material reaches the front edge of the saw table top.

4. Continue feeding the material using the push block (A12) until the cut is complete.

FIG. 36

4-3/4"

(121 mm)

A15

1/2"

(12.7 mm)

2-1/2"

(64 mm)

5-1/4"

(133 mm)

A11

(127 mm)

12"

(305 mm)

2-1/2" (64mm)

1/2"

(12.7 mm)

A14

(305mm)

4-3/4"

(121 mm)

3/8"

(9.5mm)

A12

A16

1/2"

(12.7 mm)

Push Block (Fig. 36, 37)

IMPORTANT: Only use the push block (A12) with the narrow rip auxiliary fence. Refer to

Narrow Rip Auxiliary Fence. The push block should be used once the material being cut reaches the saw table top.

1. Construct a push block using the diagram in Figure 36.

NOTE: Edges (A15) must be the same size. IMPORTANT: The over hanging edge (A16, Fig. 36) MUST be square. An uneven lip could

cause the push block to slip or push the material away from the fence.

2. Place the push block (A12, Fig. 37) behind the material and ensure the lip of the block is flush to the narrow rip auxiliary fence (A13).

3. Once the push block is in place, continue feeding the material until the cut is complete making sure the push block remains flush to the narrow rip auxiliary fence at all times.

IMPORTANT: The narrow rip auxiliary fence and the over hanging edge (A16, Fig. 36) should both be the same thickness.

FIG. 37

A12

A13

Bevel Ripping (Fig. 38)

This operation is the same as ripping except the bevel angle is set to an angle other than zero degrees.

WARNING: Before connecting

the table saw to the power source or operating the saw, always inspect the blade guard assembly and riving knife for proper alignment and clearance with saw blade. Check alignment after each change of bevel angle.

FIG. 38

Crosscutting

WARNING: NEVER touch the free

end of the workpiece or a free piece that is cut off, while the power is ON and/or the saw blade is rotating. Piece may contact the blade resulting in a thrown workpiece and possible injury.

WARNING: To reduce the risk of injury, NEVER use the fence as a guide or length stop

when crosscutting.

WARNING: NEVER use a length stop on the free end of the workpiece when crosscutting.

In short, the cut-off piece in any thru sawing (cutting completely through the workpiece) operation must never be confined — it must be allowed to move away from saw blade to prevent contact with blade resulting in a thrown workpiece and possibly injury.

WARNING: Use caution when starting the cut to prevent binding of the guard against the

workpiece resulting in damage to saw and possible injury.

CAUTION: When using a block as a cut-off gauge, the block must be at least 3/4"

(19 mm) thick and is very important that the rear end of the block be positioned so the workpiece is clear of the block before it enters the blade to prevent contact with blade resulting in a thrown workpiece and possibly injury.

1. Remove the rip fence and place the miter gauge in the desired slot.

2. Adjust the blade height so that the blade is about 1/8" (3.2 mm) higher than the top of the workpiece.

3. Hold the workpiece firmly against the miter gauge with the path of the blade in line with the desired cut location. Keep the workpiece an inch or so in front of the blade. KEEP BOTH HANDS AWAY FROM THE BLADE AND THE PATH OF THE BLADE (Fig. 39).

4. Start the saw motor and allow the blade to come up to speed.

5. While using both hands to keep the workpiece against the face of the miter gauge, and holding the workpiece flat against the table, slowly push the workpiece through the blade. Refer to Figure 38.

6. Never try to pull the workpiece with the blade turning. Turn the switch off, allow the blade to stop, and carefully slide the workpiece out.

CAUTION: Never touch or hold onto the free or cut off end of the workpiece.

FIG. 39

Bevel Crosscutting

This operation is the same as crosscutting except that the bevel angle is set to an angle other than 0°. For proper hand position, refer to Figure38.

WARNING: Before connecting the table saw to the power source or operating the saw,

always inspect the blade guard assembly and riving knife for proper alignment and clearance with saw blade. Check alignment after each change of bevel angle.

Mitering

WARNING: Miter angles greater

than 45˚ may force the blade guard assembly into the saw blade causing damage to the blade guard assembly and personal injury. Before starting the motor, test the operation by feeding the workpiece into the blade guard assembly. If the blade guard assembly contacts the blade, place the workpiece under the blade guard assembly, not touching the blade, before starting the motor.

CAUTION: Certain workpiece

shapes, such as molding may not lift the blade guard assembly properly. Feed the workpiece slowly to start the cut. If the blade guard assembly contacts the blade, place the workpiece under the blade guard assembly, not touching the blade, before starting the motor.

This operation is the same as crosscutting except the miter gauge is locked at an angle other than 0°. Hold the workpiece FIRMLY against the miter gauge and feed the workpiece slowly into the blade (to prevent the workpiece from moving). Refer to Figure 40.

FIG. 40

English

Miter Gauge Operation

To set your miter gauge, loosen the lock handle and move the miter gauge to the desired angle.

Compound Mitering

This is a combination of bevel crosscutting and mitering. Follow the instructions for both bevel crosscutting and mitering.

English

Featherboard Construction

Featherboards are used to keep the work in contact with the fence and table, and help prevent kickbacks. Dimensions for making a typical featherboard are shown in Fig. 41. Make the featherboard from a straight piece of wood that is free of knots and cracks. Clamp the featherboard to the fence and table so that the leading edge of the featherboard will support the workpiece until the cut is complete (Fig. 42). An 8" (203 mm) high flat board can be clamped to the rip fence and the featherboard can be clamped to the 8" (203mm) high board.

FIG. 41

(102mm)

THE KERF SHOULD BE ABOUT 1/4"

(6.4mm) APART

24" (610mm)

60º

5" (127mm)

3/4"

(20mm)

Dust Collection

Your table saw is equipped with a dust shroud and dust collection port. For best results, connect a vacuum to the port at the rear of the saw.

After extended use, the saw’s dust collection system may become clogged. To clear the dust collection system:

1. Unplug the saw.

2. Turn the saw on its side, so the bottom, open part of the unit is accessible.

3. Open the dust access door (UU) shown in Figure 43 by removing the wing screws (V V). Clean out the excess dust, and re-secure the access door with the wing screws.

Lubrication

1. All motor bearings are permanently lubricated at the factory and no additional lubrication is needed.

2. The height adjustment gear may require periodic cleaning and lubrication (Fig. 44). If you have difficulty raising or lowering the blade, contact a D service center.

FIG. 46

EWALT authorized

FIG. 43

V V

FIG. 44

WARNING: Use featherboards for all non-thru sawing operations where the blade guard

assembly, anti-kickback assembly and riving knife cannot be used. Always replace the

blade guard assembly, anti-kickback assembly and riving knife when the non-thru sawing operation is complete. Make sure the featherboard presses only on the portion of

the workpiece in front of the blade.

FIG. 42

STORAGE (Fig. 45, 46)

1. Attach push stick (U) to fence.

2. Remove blade guard assembly (D). Refer to To Remove Blade Guard Assembly. Slide blade guard assembly into brackets as shown.

3. Depress the stem (GG) on the anti-kickback

FIG. 45

assembly (Q) to allow the assembly to slide from the riving knife slot.

4. Position anti-kickback assembly into the storage hole

as shown. While depressing stem (GG) slide the antikickback assembly across the storage slot (A4) and release pin to lock into place.

5. Loosen the riving knife lock knob (YY, Fig. 25) (minimum of three turns).

6. Push riving knife lock knob (YY) toward the riving knife as indicated by the yellow arrows on the knob to disengage riving knife lock pin.

7. Lift and slide the riving knife from saw.

8. Remove wingnut securing blade wrenches (V). Place riving knife (FF) onto post with blade wrenches and secure with wingnut.

MAINTENANCE

WARNING: To reduce the risk of injury, turn unit off and disconnect machine from

power source before installing and removing accessories, before adjusting or changing set-

ups or when making repairs. An accidental start-up can cause injury.

Cleaning

WARNING: When cleaning, use only mild soap and a damp cloth on plastic parts. Many

household cleaners contain chemicals which could seriously damage plastic. Also, do not use gasoline, turpentine, lacquer or paint thinner, dry cleaning fluids or similar products which may seriously damage plastic parts. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.

Accessories

WARNING: Since accessories, other than those offered by DEWALT, have not been tested

with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only D

If you need assistance in locating any accessory, please contact D 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-D our website www.D

EWALT recommended accessories should be used with this product.

EWALT Industrial Tool Co.,

EWALT (1-800-433-9258) or visit

EWALT.com.

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush inspection and replacement) should be performed by a D a D

EWALT authorized service center or other qualified service personnel. Always use identical

EWALT factory service center,

replacement parts.

Thank you for your purchase. Register your product now for:

• WARRANTY SERVICE: Registering your product will help you obtain more efficient warranty service in case there is a problem with your product.

• CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or theft, your registration of ownership will serve as your proof of purchase.

• FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely event a safety notification is required under the Federal Consumer Safety Act.

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty materials or workmanship for three years from the date of purchase. This warranty does not cover part failure due to normal wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit www.dewalt.com or call 1-800-4-D accessories or damage caused where repairs have been made or attempted by others. This warranty gives you specific legal rights and you may have other rights which vary in certain states or provinces.

In addition to the warranty, D

EWALT will maintain the tool and replace worn parts caused by normal use, for free, any time

during the first year after purchase.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your D Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt for a full refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America, see country specific warranty information contained in the packaging, call the local company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-4-D

EWALT (1-800-433-9258) for a free replacement.

EWALT (1-800-433-9258). This warranty does not apply to

EWALT tools are covered by our:

1 YEAR FREE SERVICE

EWALT Power Tool, Laser, or

English

Déﬁ nitions: Consignes de sécurité

Les définitions ci-après décrivent le degré de sévérité assigné à chaque terme. Veuillez lire ce manuel et prêter attention à ces symboles.

DANGER: Indique une situation de danger imminent qui, si rien n’est fait pour l’éviter,

aura comme conséquences la mort ou des dommages corporels graves.

AVERTISSEMENT: Indique une situation de danger potentiel qui, si rien n’est fait pour

l’éviter, pourra avoir comme conséquences la mort ou des dommages corporels

graves.

ATTENTION: Indique une situation de danger potentiel qui, si rien n’est fait pour l’éviter,

pourra avoir comme conséquences des dommages corporels mineurs ou modérés. AVIS : indique une pratique ne posant aucun risque de dommages corporels mais

qui par contre, si rien n’est fait pour l’éviter, pourrait poser des risques de dommages

matériels.

POUR TOUT COMMENTAIRE OU QUESTION RELATIF À CET OUTIL OU TOUT AUTRE OUTIL D

EWALT, COMPOSEZ GRATUITEMENT LE: 1-800-4-DEWALT (1-800-433-9258).

Règles de sécurité – Généralités

AVERTISSEMENT : lire ces directives avant toute utilisation. Tout manquement aux

directives suivantes pose des risques de choc électrique, d’incendie et/ou de blessure grave.

CONSERVER CES CONSIGNES

AVERTISSEMENT: SE CONFORMER AUX NORMES DU CODE EN MATIÈRE DE

CÂBLAGE et connexions électriques pour prévenir tout risque de décharge électrique ou

d’électrocution.

Double isolation

Si la scie a été conçue d’usine avec une double isolation, lire les consignes suivantes.

Français

Ce symbole les décharges électriques, les outils à double isolation sont complètement recouverts de deux couches distinctes d’isolant électrique ou d’une double épaisseur de matière isolante. Les outils possédant ce type d’isolation ne sont pas destinés à être mis à la terre. Par conséquent, ils sont munis d’une fiche à deux broches permettant d’utiliser une rallonge ne nécessitant aucune prise à la terre. Réparer ou remplacer immédiatement tout cordon endommagé ou usé.

REMARQUE : le fait que cet outil soit muni d’une double isolation ne signifie pas que l’utilisateur peut cesser de respecter les consignes de sécurité qui s’imposent. L’isolation offre une protection supplémentaire contre les blessures causées par toute défaillance électrique des systèmes d’isolation internes.

FICHES POLARISÉES

Pour réduire tout risque de choc électrique, cet outil est muni d’une fiche polarisée (l’une des lames est plus large que l’autre), laquelle ne peut être raccordée qu’à une prise polarisée et ce, dans un seul sens. Si la fiche ne rentrait pas complètement dans la prise, inverser le sens de la fiche. Si la fiche ne s’adapte toujours pas, faire appel à un électricien qualifié pour qu’il installe la prise appropriée. Ne jamais modifier la fiche en aucune façon.

atteste d’une fabrication à double isolation. Afin de protéger l’utilisateur contre

Consignes de sécurité importantes

• POUR RÉDUIRE TOUT RISQUE DE DOMMAGES CORPORELS, utiliser

systématiquement l’ensemble des composants du dispositif de protection (dispositif de carter de lame, couteau diviseur et dispositif anti-rebonds) au cours des opérations pour lesquelles ils ont été conçus, et ce, pendant toute la durée de coupe.

• RETIRER TOUTE CLÉ ET TOUT OUTIL DE RÉGLAGE. Vérifier systématiquement que

toute clé ou outil de réglage a été retiré de la broche avant de mettre l’outil en marche. Outils, chutes, ou autres débris pourraient être projetés brusquement, et causer des dommages corporels.

• MAINTENIR L’AIRE DE TRAVAIL PROPRE. Les établis et locaux encombrés sont

propices aux accidents.

• NE PAS UTILISER LA MACHINE DANS UN ENVIRONNEMENT DANGEREUX. Ne

pas utiliser d’outils électriques dans des endroits trempés ou humides, ou sous la pluie, pour éviter tout risque de décharge électrique ou d’électrocution. Maintenir l’atelier bien éclairé pour éviter les chutes ou la mise en danger des bras, mains ou doigts.

• MAINTENIR LES ENFANTS À L’ÉCART. Pour leur sécurité, maintenir les visiteurs à

l’écart de l’espace de travail. Votre atelier est un environnement potentiellement dangereux.

• PROTÉGER L’ATELIER À L’AIDE DE DISPOSITIFS À L’ÉPREUVE DES ENFANTS tels

cadenas et interrupteurs principaux, ou en retirant toute clé de démarrage. Le démarrage non autorisé d’une machine par un enfant ou un visiteur comporte des risques de dommages corporels.

• NE PAS FORCER L’OUTIL. Il effectuera un meilleur travail, à un degré de sécurité plus

élevé, à la vitesse pour laquelle il a été conçu.

• UTILISER L’OUTIL ADÉQUAT. Ne pas forcer l’outil, ou un accessoire, pour effectuer un

travail pour lequel il n’a pas été conçu. Le fait d’utiliser un outil ou accessoire inadéquat comporte des risques de dommages corporels.

• UTILISER UNE RALLONGE ADÉQUATE. S’assurer que la rallonge est en bon état.

Si l’appareil est équipé d’un cordon amovible, utiliser seulement des rallonges trifilaires, équipées d’une fiche tripolaire mise à la terre, et les prises tripolaires adaptées. S’assurer que les valeurs nominales de la rallonge utilisée correspondent bien à celle de l’outil alimenté. L’usage d’une rallonge de calibre insuffisant causera une chute de tension entraînant perte de puissance et surchauffe. Le tableau ci-dessous illustre les calibres à utiliser selon la longueur de rallonge et l’intensité nominale indiquée sur la plaque signalétique. En cas de doute, utiliser le calibre suivant. Plus le calibre est petit, plus la rallonge peut supporter de courant.

CALIBRES MINIMAUX DES RALLONGES

Volts Longueur totale de cordon en pieds

120V 0-25 26-50 51-100 101-150 240V 0-50 51-100 101-200 201-300

Intensité (en ampères)

Supérieur Inférieur AWG à à

0 - 6 18 16 16 14 6 - 10 18 16 14 12 10 - 12 16 16 14 12 12 - 16 14 12 Non recommandé

• PORTER LES VÊTEMENTS APPROPRIÉS. Éviter vêtements amples, gants, cravates,

bagues, bracelets ou autres bijoux qui pourraient rester coincés dans les pièces mobiles. Il est recommandé de porter des chaussures antidérapantes. Couvrir ou attacher les cheveux longs. Prendre des précautions à proximité des évents car ils cachent des pièces mobiles.

• ARRIMER LA PIÈCE À TRAVAILLER. Utiliser des colliers de serrage pour maintenir

le travail lorsque c’est utile (particulièrement pour couper avec un espacement nul de plaquette de renfort/plaque de lumière). C’est plus sûr que de le faire manuellement et cela laisse les mains libres pour utiliser l’outil.

+ 36 hidden pages