DeWalt D0855, D0820, D0821, D0822, D0830 Instruction Manual

LULU

C3£3
<69

-----W

.JI--

'0 Z

n<
>-0

O>
OF-

'"E

6969
LUz

123--

69w

©F-

Em

z t.t.l

1.1.169

o<

_t.l.l

Z_j

'S,i

rr z

WLIJ

a-_d

oQ:E

ujIJJ

n
©<©
> rr

V-<a_

O'F- J

_zLIJ

rr<
69<

z_69

7

.E

@

>

L,.

0 e-

eOLf) U)'_

_m_o

_E

o_OE

_ _=

eo eo ,_,,

tO _o _ _o

ooo_,

OtO00

DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286

Part No. 658028-00 DC820, etc. Copyright © 2007, 2008 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black
color scheme; the "D" shaped air intake grill; the array of pyramids on the handgrip; the kit box
configuration; and the array of lozenge-shaped humps on the surface of thetool.

F -y

Definitions: Safety Guidelines

The definitions below describe the level of severity for each signal word. Please read
the manual and pay attention to these symbols.
_,DANGER: Indicates an imminently hazardous sfuation which, if not avoided, will

result in death or serious injury.
_, WARNING: Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
_CAUTION: Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates a potentially hazardous

__situation which, if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,
CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258).

_ WARNING: To reduce the risk of read the instruction manual.

injury,

General Power Tool Safety Warnings

A ARNIN!! Read all safety warnings and instructions Failure to follow the warnings

and instructions may result in electric shock, fire and/or serious injury,

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tooL

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools create sparks which may ignite the dust

or fumes.

c) Keep children and bystanders away while operating a power tooL Distractions can

cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not

use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your body is
earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the

power tooL Keep cord away from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) ff operating a power tool in a damp location is unavoidable, use a ground fault

circuit interrupter (GFCl) protected supply. Use of a GFCI reduces the risk of electric
shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention while operating power tools may
result in serious personal injury,

b) Use personal protective equipment. Always wear eye protection. Protective

equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off position before

connecting to power source and/or battery pack, picking up or carrying the tool
Carrying power tools with your finger on the switch or energising power tools that have
the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A wrench or

a key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables better

control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and

gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in
moving parts.

g) ff devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used. Use of dust collection can
reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tooL Use the correct power tool for your application. The

correct power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power tool

that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the power

tool before making any adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the power tool accidentally,

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool Power
tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misallgnment or binding of moving parts, breakage

of parts and any other condition that may affect the power tool's operation. If
damaged, have the power tool repaired before use. Many accidents are caused by
poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier to control

g) Use the power tool, accessories and tool bits, etc. in accordance with these

instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended could
result in a hazardous situation.

5) BATTERY TOOL USE AND CARE

a) Recharge only with the charger specified by the manufacturer. A charger that is

suitable for one type of battery pack may create a risk of fire when used with another
battery pack.

b) Use power tools only with specifically designated battery packs. Use of any other

battery packs may create a risk of injury and fire.

c) When battery pack is not in use, keep it away from other metal objects like paper

clips, coins, keys, nails, screws, or other small metal objects that can make a
connection from one terminal to another. Shorting the battery terminals together may
cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from the battery; avoid contact, ff

contact accidentally occurs, flush with water, ff liquid contacts eyes, additionally
seek medical help. Liquid ejected from the battery may cause irritation or burns.

6) SERVICE

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

Additional Specific Safety Rules

• Hold power tools by insulated gripping surfaces when performing an operation where
the cutting tool may contact hidden wiring or its own cord. Contact witha "live" wire will

make exposed metal parts of the tool "live" and shock the operator.

• Use clamps or other practical way to secure and support the workpiece to a stable
platform. Holding the work by hand or against your body is unstable and may lead to loss of

control

• Wear safety goggles or other eye protection. Hammering and drilling operations cause
chips to fly, Flying particles can cause permanent eye damage.

• Bits, sockets and tools get hot during operation. Wear gloves when touching them.

• Do not operate this tool for long periods of time. Vibration caused by tool action may be

harmful to your hands and arms. Use gloves to provide extra cushion and limit exposure by
taking frequent rest periods.

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses.
Also use face or dust mask if cutting operation is dusty, ALWAYS WEAR CERTIFIED SAFETY
EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI $12.6 ($3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work.
To reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter out
microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with
soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote
absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust, which may cause serious
and permanent respiratory or other injury, Always use NIOSH/OSHA approved respiratory
protection appropriate for the dust exposure. Direct particles away from face and body,

WARNING: Always wear proper personal hearing protection that conforms to ANSI
$12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product
may contribute to hearing loss.

CAUTION: When not in use, place tool on its side on a stable surface where it will not
cause a tripping or falling hazard. Some tools with large battery packs will stand upright on
the battery pack but may be easily knocked over.

• The label on your tool may include the following symbols. The symbols and their definitions

are as follows:

V...................... volts

Hz.................... hertz

min .................. minutes

.... ............... direct current

@ .................... Class I Construction

(grounded)

[] .................... Class II Construction

(double insulated)

.../min ............. per minute

IPM .................. impacts per minute

A...................... amperes

W..................... watts

* ................... alternating current

................... alternating or direct current

no .................... no load speed

.................... earthing terminal

_, .................... safety alert symbol

BPM ................ beats per minute

RPM ................ revolutions per minute

Important Safety Instructions for All Battery Packs

When ordering replacement battery packs, be sure to include catalog number and voltage.
Consult the chart at the end of this manual for compatibility of chargers and battery packs.
The battery pack is not fully charged out of the carton. Before using the battery pack and
charger, read the safety instructions below. Then follow charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Inserting or removing the battery from the charger may

ignite the dust or fumes.

• NEVER force battery pack into charger. DO NOT modify battery pack in any way
to fit into a non-compatible charger as battery pack may rupture causing serious
personal injury. Consult the chart at the end of this manual for compatibility of batteries and
chargers.

• Charge the battery packs only in DEWALT chargers.

• DO NOT splash or immerse in water or other liquids.

• Do not store or use the tool and battery pack in locations where the temperature may
reach or exceed 105°F (40°C) (such as outside sheds or metal buildings in summer).

ADANGER: Electrocution hazard. Never attempt to open the battery pack for any reason.
If battery pack case is cracked or damaged, do not insert into charger. Do not crush, drop or
damage battery pack. Do not use a battery pack or charger that has received a sharp blow,
been dropped, run over or damaged in any way (i.e., pierced with a nail, hit with a hammer,
stepped on). Electric shock or electrocution may result. Damaged battery packs should be
returned to service center for recycling.

NOTE: Battery storage and carrying caps are provided for use whenever the
battery is out of the tool or charger. Remove cap before placing battery in charger
or tool.

WARNING: Fire hazard. Do not store or carry battery so that metal
objects can contact exposed battery terminals. For example, do not place
battery in aprons, pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws,
keys, etc. without battery cap. Transporting batteries can possibly cause fires if the battery
terminals inadvertently come in contact with conductive materials such as keys, coins,
hand tools and the like. The US Department of Transportation Hazardous Material Regulations
(HMR) actually prohibit transporting batteries in commerce or on airplanes (i.e., packed in
suitcases and carry-on luggage) UNLESS they are properly protected from short circuits. So
when transporting individual batteries, make sure that the battery terminals are protected and
well insulated from materials that could contact them and cause a short circuit.

SPECIFIC SAFETY INSTRUCTIONS FOR NICKEL CADMIUM (NiCd) OR NICKEL METAL
HYDRIDE (NiMH)

• Do not incinerate the batterypack even flit is severely damaged or is completely worn

out. The battery pack can explode in a fire.

• A small leakage of liquid from the battery pack cells may occur under extreme usage

or temperature conditions. This does not indicate a failure.
However, if the outer seal is broken:

a. and the battery liquid gets on your skin, immediately wash with soap and water for several

minutes.

b. and the battery liquid gets into your eyes, flush them with clean water for a minimum of

10 minutes and seek immediate medical attention. (Medical note: The liquid is 25-35%

solution of potassium hydroxide.)

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (LI-ION)

• Do not incinerate the battery pack even if it is severely damaged or is completely

worn out. The battery pack can explode in a fire. Toxic fumes and materials are created
when lithium ion battery packs are burned.

• ff battery contents come into contact with the skin, immediately wash area with

mild soap and water, ff battery liquid gets into the eye, rinse water over the open eye for
15 minutes or until irritation ceases, ff medical attention is needed, the battery electrolyte is
composed of a mixture of liquid organic carbonates and lithium salts.

• Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If

symptoms persists, seek medical attention.

WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame.

The RBRC TM Seal

The RBRC TM (Rechargeable Battery Recycling Corporation) Seal on the nickel
cadmium, nickel metal hydride or lithium ion batteries (or battery packs) indicate
that the costs to recycle these batteries (or battery packs) at the end of their useful
life have already been paid by DEWALT. In some areas, it is illegal to place spent
nickel cadmium, nickel metal hydride or lithium ion batteries in the trash or
municipal solid waste stream and the RBRC program provides an environmentally
conscious alternative.
RBRC TM in cooperation with DEWALT and other battery users, has established programs in
the United States and Canada to facilitate the collection of spent nickel cadmium, nickel metal
hydride or lithium ion batteries. Help protect our environment and conserve natural resources
by returning the spent nickel cadmium and nickel cadmium, nickel metal hydride or lithium ion
batteries to an authorized DEWALT service center or to your local retailer for recycling. You may
also contact your local recycling center for information on where to drop off the spent battery.
RBRC TM is a registered trademark of the Rechargeable Battery Recycling Corporation.

Important Safety Instructions for All Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important safety and operating instruc-
tions for battery chargers.

• Before using charger, read all instructions and cautionary markings on charger, batterypack,

and product using battery pack.
@,DANGER: Electrocution hazard. 120 volts are present at charging terminals. Do not probe
with conductive objects. Electric shock or electrocution may result.
_ WARNING: Shock hazard. Do not allow any liquid to get inside charger. Electric shock may
result.
_ CAUTION: Burn hazard. To reduce the risk of injury, charge only DEWALT rechargeable
batteries. Other types of batteries may burst causing personal injury and damage.
A CAUTION: Under certain conditions, with the charger plugged in to the power supply, the
exposed charging contacts inside the charger can be shorted by foreign material Foreign
materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any

buildupofmetallicparticlesshouldbekeptawayfromchargercavities.Alwaysunplugthe
chargerfromthepowersupplywhenthereisnobatterypackinthecavity.Unplugcharger
beforeattemptingtoclean.

• DO NOT attempt to charge the battery pack with any chargers other than the ones in

this manual The charger and batter y pack are specifically designed to work together.

• ThesechargersarenotintendedforanyusesotherthanchargingDEWALTrechargeable
batteries. Any other uses may result in risk of fire, electric shock or electrocution.

• Do not expose charger to rain or snow.

• Pull by plug rather than cord when disconnecting charger. This will reduce risk of
damage to electric plug and cord.

• Make sure that cord is located so that it will not be stepped on, tripped over, or

otherwise subjected to damage or stress.

• Do not use an extension cord unless it is absolutely necessary. Use of improper
extension cord could result in risk of fire, electric shock, or electrocution.

• When operating a power tool outdoors, use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

• An extension cord must have adequate wire size (AWG or American Wire Gauge) for
safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that
is 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating. When using more than one extension to
make up the total length, be sure each individual extension contains at least the minimum
wire size. The following table shows the correct size to use depending on cord length and
nameplate ampere rating, ff in doubt, use the next heavier gauge. The smaller the gauge
number, the heavier the cord.

Recommended Minimum Wire Size for Extension Cords

Total Length of Cord

25 ft. 50 ft. 75 ft. 100 ft. 125 ft. 150 ft. 175 ft.

7.6 m 15.2 m 22.9 m 30.5 m 38.1 m 45.7 m 53.3 m

Wire Size AWG

18 18 16 16 14 14 12

• Do not place any object on top of charger or place the charger on a soft surface that
might block the ventilation slots and result in excessive internal heal Place the charger

in a position away from any heat source. The charger is ventilated through slots in the top and
the bottom of the housing.

• Do not operate charger with damaged cord or plug.

• Do not operate charger ff it has received a sharp blow, been dropped, or otherwise
damaged in any way. Take it to an authorized service center.

• Do not disassemble charger; take # to an authorized service center when service or
repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution or
fire.

• Disconnect the charger from the outlet before attempting any cleaning. This will
reduce the risk of electric shock. Removing the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

• The charger is designed to operate on standard 120V household electrical power. Do
not attempt to use it on any other voltage. This does not apply to the vehicular charger.

Using Automatic Tune-Up TM Mode

The automatic Tune-Up TM Mode equalizes or balances the individual cells in the battery pack
allowing it to function at peak capacity. Battery packs should be tuned up weekly or after
10 charge/discharge cycles or whenever the pack no longer delivers the same amount of work.
To use the automatic Tune-Up TM, place the battery pack in the charger and leave it for at least 8
hours. The charger will cycle through the following modes.

1. The red light will blink continuously indicating that the 1-hour charge cycle has started.

2. When the 1-hour charge cycle is complete, the light will stay on continuously and will no
longer blink. This indicates that the pack is fully charged and can be used at this time.

3. If the pack is left in the charger after the initial 1-hour charge, the charger will begin the
Automatic Tune-Up TM mode. This mode continues up to 8 hours or until the individual cells
in the battery pack are equalized. The battery pack is ready for use and can be removed at
any time during the Automatic Tune-Up TM mode.

4. Once the Automatic Tune-Up TM mode is complete, the charger will begin a maintenance
charge; the red indicator will remain lit.

Chargers

Your tool uses a DEWALT 7.2, 9.6, 12, 14,4 or 18 volt charger. Be sure to read all safety
instructions before using your charger. Consult the chart at the end of this manual for compatibility
of chargers and battery packs.

Charging Procedure

A DANGER: Electrocution hazard. 120 volts present at charging terminals. Do not probe with
conductive objects. Danger of electric shock or electrocution.

1. Plug the charger into an appropriate outlet before inserting battery pack.

2. Insert the battery pack into the charger. The red (charging) light will blink continuously
indicating that the charging process has started.

3. The completion of charge will be indicated by the red light remaining ON continuously. The
pack is fully charged and may be used at this time or left in the charger.

Indicator Light Operation

PACK CHARGING ................... m m _ _ _ _ m _

PACK CHARGED .....................

HOT/COLD PACK DELAY ........ _ [] _ [] _ []

REPLACE PACK ...................... ® O®OOOOOOOOOO®®

PROBLEM POWER LiNE ........ • ® ® ® ® ® ® • • •

Charge Indicators

Some chargers are designed to detect certain problems that can arise with battery packs.
Problems are indicated by the red light flashing at afast rate. If this occurs, re-insert battery pack
into the charger. If the problem persists, try a different battery pack to determine ifthe charger is
OK. If the new pack charges correctly, then the original pack is defective and should be returned
to a service center or other collection site for recycling. If the new battery pack elicits the same
trouble indication as the original, have the charger tested at an authorized service center.

HOT/COLD PACK DELAY
Some chargers have a Hot/Cold Pack Delay feature: when the charger detects a battery that is
hot, it automatically starts a Hot Pack Delay, suspending charging until the battery has cooled.
After the battery has cooled, the charger automatically switches to the Pack Charging mode.
This feature ensures maximum battery life. The red light flashes long, then short while in the Hot
Pack Delay mode.
PROBLEM POWER LINE
Some chargers have a Problem Power Line indicator. When the charger is used with some
portable power sources such as generators or sources that convert DC to AC, the charger may
temporarily suspend operation, flashing the red light with two fast blinks followed by a

pause. This indicates the power source is out of limits.
LEAVING THE BATTERY PACK IN THE CHARGER
The charger and battery pack can be left connected with the red light glowing indefinitely. The

charger will keep the battery pack fresh and fully charged.
NOTE: A battery pack will slowly lose its charge when kept out of the charger. If the battery pack
has not been kept on maintenance charge, it may need to be recharged before use. A battery
pack may also slowly lose its charge if left in a charger that is not plugged into an appropriate

AC source.
WEAK BATTERY PACKS: Chargers can also detect a weak battery pack. Such batteries are
still usable but should not be expected to perform as much work. The charger will indicate to

replace battery pack.

Important Charging Notes

1. Longest life and best performance can be obtained if the battery pack is charged when the
air temperature is between 65°F and 75°F (18 °- 24°C). DO NOT charge the battery pack in
an air temperature below +40°F (+4.5°C), or above +105°F (+40.5°C). This is important and
will prevent serious damage to the battery pack.

2. The charger and battery pack may become warm to touch while charging. This is a normal
condition, and does not indicate a problem. To facilitate the cooling of the battery pack after
use, avoid placing the charger or battery pack in a warm environment such as in a metal
shed, or an uninsulated trailer.

3. If the battery pack does not charge properly:
a. Check current at receptacle by plugging in a lamp or other appliance;
b. Check to see if receptacle is connected to a light switch which turns power off when you

turn out the lights;

c. Move charger and battery pack to a location where the surrounding air temperature is

approximately 65°F - 75°F (18 °- 24°C);

d. If charging problems persist, take the tool, battery pack and charger to your local service

center.

4. The battery pack should be recharged when it fails to produce sufficient power on jobs which
were easily done previously. DO NOT CONTINUE to use under these conditions. Follow the
charging procedure. You may also charge a partially used pack whenever you desire with no
adverse affect on the battery pack.

5. Under certain conditions, with the charger plugged into the power supply, the exposed
charging contacts inside the charger can be shorted by foreign material. Foreign materials
of a conductive nature such as, but not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles should be kept away from charger cavities.
Always unplug the charger from the power supply when there is no battery pack in the cavity.
Unplug charger before attempting to clean.

6. Do not freeze or immerse charger in water or any other liquid.

i_ WARNING: Shock hazard. Don't allow any liquid to get inside charger. Electric shock may

result.
_ CAUTION: Never attempt to open the battery pack for any reason, ff the plastic housing of
the battery pack breaks or cracks, return to a service center for recycling.

Storage Recommendations

1. The best storage place is one that is cool and dry away from direct sunlight and excess heat
or cold.

2. Long storage will not harm the battery pack or charger. Under proper conditions, they can
be stored for 5 years or more.

SAVE THESE INSTRUCTIONS FOR FUTURE USE

Motor

Voltage decrease of more than 10% will cause loss of power and overheating. All DEWALT tools
are factory tested; if this tool does not operate, check your battery pack.

FIG. 1 FIG. 2

FIG. 3

J
K

FIG. 4

E

D

FIG. 5

COMPONENTS (Fig. 3)

i_ WARNING: Never modify the power tool or any part of it. Damage or personal injury could
result.

A. Trigger switch F. Detent pin
B. Rocker switch (DW059) G. Anvil
C. Forward/reverse button H. Battery release buttons
D. Sleeve I. Worklight

E. 1/4" hex quick-release chuck J. Belt hook (optional accessory)
INTENDED USE
These heavy-duty impact wrench/drivers are designed for professional impact screwdriving
applications. The impact function makes this tool particularly useful for driving fasteners in wood,
metal and concrete. DO NOT use under wet conditions or in presence of flammable liquids or
gases.
These heavy-duty impact wrench/drivers are professional power tools. DO NOT let children
come into contact with the tool. Supervision is required when inexperienced operators use this

tool.

Belt Hook (Optional Accessory)

i_ WARNING: Toreduce the risk of serious personal injury, DO NOT suspend tool overhead
or suspend objects from the belt hook. ONLY hang tool's belt hook from a work belt.
i_ WARNING: To reduce the risk of serious personal injury, ensure the screw (K) holding the
belt hook is secure.

The belt hook (J) can be be attached to either side of the tool to accommodate left- or right-
handed users. If the hook is not desired at all, it can be removed from the tool.
To move belt hook, remove the screw (K) that holds the belt hook in place then reassemble on
the opposite side.

OPERATION

i_ WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect
battery pack before making any adjustments or removing/installing attachments or
accessories.

Installing and Removing the Battery Pack

NOTE: Make sure your battery pack is fully charged.
To install the battery pack into the tool handle, align the base of the tool with the notch inside
the tool's handle (Fig. 2) and slide the battery pack firmly into the handle until you hear the lock
snap into place.
To remove the battery pack from the tool, press the release buttons (H) and firmly pull the
battery pack out of the tool handle. Insert it into the charger as described in the charger section

of this manual.

Switch - DW059 (Fig. 3)

Pressing the BOTTOM part of the rocker switch (B) runs the tool in forward (right hand thread)
direction. Pressing the TOP of the switch reverses motor direction. This allows "rocking"
fasteners to break them loose.

Variable Speed Trigger Switch (Fig. 3)

To turn the tool on, squeeze the trigger switch (A). To turn the tool off, release the trigger
switch. Your tool is equipped with a brake. The chuck will stop as soon as the trigger switch is
fully released. The variable speed switch enables you to select the best speed for a particular
application. The more you squeeze the trigger, the faster the tool will operate. Use lower speeds
for starting holes without a center punch, drilling in metals or plastics, or driving screws. For
maximum tool life, use variable speed only for starting holes or fasteners.
NOTE: Continuous use in variable speed range is not recommended. It may damage the switch
and should be avoided.

Forward/Reverse Control Button (Fig. 3)

Aforward/reverse control button (C) determines the direction of the tool and also serves as a lock
off button. To select forward rotation, release the trigger switch and depress the forward/reverse
control button on the right side of the tool. To select reverse, depress the forward/reverse control
button on the left side of the tool. The center position of the control button locks the tool in the OFF
position. When changing the position of the control button, be sure the trigger is released.
NOTE: The first time the tool is run after changing the direction of rotation, you may hear aclick
on start up. This is normal and does not indicate a problem.

Worklight (Fig. 3)

There is a worklight (I) located just above the trigger switch (A). The worklight will be activated
when the trigger switch is squeezed.
NOTE: The worklight is for lighting the immediate work surface and is not intended to be used
as a flashlight.

Quick.Release Chuck (Fig. 4)

D0825, D0827, D0835, D0845, D0855
NOTE: The chuck accepts 1/4" (6.35 mm) hex accessories only.
Place the switch in the locked off (center) position or remove battery pack before changing

accessories.
To install an accessory, pull the chuck collar (D) away from the front of the tool, insert the

accessory and release the collar. The accessory is locked in place.
To remove an accessory, pull the chuck collar away from the front of the tool. Remove the
accessory and release the collar.

Anvil With Detent Pin (Fig. 5)

D0820, D0821, D0822, D0823, D0830, D0840, DW059
Place the switch in the locked off (center) position or remove battery pack before changing
accessories.
To install a socket on the anvil, align the hole in the side of the socket with the detent pin (F) on
the anvil (G). Press the socket on until the detent pin engages inthe hole. Depression of detent
pin may be necessary to aid installation of socket.
_ CAUTION: Use only impact sockets. Non-impact sockets may break and cause a hazardous

condition. Inspect socket prior to use to ensure that it contains no cracks.

To remove a socket, depress the detent pin through the hole and pull the socket off.

Usage

Your impact tool generates the following output torque:

Cat # Ft.-Lbs. In.-Lbs. Nm Cat # Ft.-Lbs. In.-Lbs. Nm
DC820 145 1740 195 DC835 103 1240 140
DC821 160 1920 215 DC840 120 1440 160
DC822 145 1740 195 DC841 105 1260 145
DC823 120 1440 160 DC845 96 1150 130
DC825 111 1330 150 DC855 80 960 110
DC827 111 1330 150 DW059 300 3600 405
DC830 135 1620 180

_ CAUTION: Ensure fastener and/or system will withstand the level of torque generated by the

tooL Excessive torque may cause breakage and possible personal injury.

1. Place the socket on the fastener head. Keep the tool pointed straight at the fastener.

2. Press switch to start operation. Always check torque with a torque wrench, as the fastening
torque is affected by many factors including the following:

• Voltage: Low voltage, due to a nearly discharged battery, will reduce fastening torque.

• Socket size: Failure to use the correct socket size will cause a reduction in fastening
torque.

• Bolt Size: Larger bolt diameters generally require higher fastening torque. Fastening
torque will also vary according to length, grade, and torque coefficient.

• Bolt: Ensure that all threads are free of rust and other debris to allow proper fastening
torque.

• Material'. The type of material and surface finish of the material will affect fastening
torque.

• Fastening Time: Longer fastening time results in increased fastening torque. Using a
longer fastening time than recommended could cause the fasteners to be overstressed,
stripped or damaged.

MAINTENANCE

_ WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect
battery pack before making any adjustments or removing/installing attachments or
accessories.

Cleaning

A WARNING: Blow dirt and dust out of all air vents with clean, dry aft at least once a week.
To minimize the risk of eye injury, always wear ANSI Z87. 1 approved eye protection when
performing this.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts
of the tooL These chemicals may weaken the plastic materials used in these parts. Use a cloth
dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse
any part of the tool into a liquid.

CHARGER CLEANING INSTRUCTIONS
_,WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning.

Dirt and grease may be removed from the exterior of the charger using a cloth or soft
non-metallic brush. Do not use water or any cleaning solutions.

Accessories

_WARNING: Since accessories, other than those offered by DEWALT, have not been tested
with this product, use of such accessories with this tool could be hazardous. Toreduce the risk
of injury, only DEWALT, recommended accessories should be used with this product.

Recommended accessories for use with your tool are available at extra cost from your local
service center. If you need any assistance in locating any accessory, please contact DEWALT
Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-DEWALT
(1-800-433-9258) or visit our website www.dewalt.com.
,&CAUTION: Use only impact sockets. Non-impact sockets may break and cause a

hazardous condition. Inspect socket prior to use to ensure that it contains no cracks.

Repairs

The charger is not serviceable. There are no serviceable parts inside the charger.
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustments (including
brush inspection and replacement) should be performed by a DEWALT factory service center,
a DEWALT authorized service center or other qualified service personnel. Always use identical
replacement parts.

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty materials or workmanship for
three years from the date of purchase. This warranty does not cover part failure due to normal
wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit
www.dewalt.com or call 1-800-4-DEWALT (1-800-433-9258). This warranty does not apply to
accessories or damage caused where repairs have been made or attempted by others. This
warranty gives you specific legal rights and you may have other rights which vary in certain
states or provinces.

In addition to the warranty, DEWALT tools are covered by our:

1 YEAR FREE SERVICE
DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any time
during the first year after purchase.

2 YEARS FREE SERVICE ON DEWALT BATTERY PACKS
DC9071, DC9091, DC9096, DC9280, DC9360 and DC9180

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your DEWALT Power Tool, Laser, or
Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt
for a full refund - no questions asked.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products
sold in Latin America, see country specific warranty information contained either in the
packaging, call the local company or see website for warranty information.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1-800-4-DEWALT for a free replacement.

BCXXX

T0 REDUCE THE RiSK OF INJURY,
USER MUST READ INSTRUCTION

MANUAL USE ONLY WITH

DEWALTBATTERIES. ALWAYS USE PROPER EYE AND
RESPIRATORY PROTECTION.

BEWALTINOOSTRiALTOOLCO,,BALTIMORE,MB 21286O,S,A,

FORSERVICEiNFORMATION,CALL1-800-¢.DEWALTwww.D_WALT=com

r

Ddfinitions : lignes directrices en matidre

de sdcuritd

Les d6finitions ci-dessous d6crivent le niveau de danger pour chaque mot-
indicateur employ& Lire le mode d'emploi et porter une attention particuli_re &
ces symboles.
i_DANGER : indique une situation dangereuse imminente qui, si elle n'est pas
6vit6e, entrainera la mort ou des blessures graves

i_4VERTISSEMENT : indique une situation potentiellement dangereuse qui, si
elle n'est pas 6vit6e, pourrait entraTner la mort ou des blessures graves
_4TTENTION : indique une situation potentiellement dangereuse qui, si elle
n'est pas 6vit6e, pourrait entraTner des blessures legeres ou moderees.
ATTENTION : utilis6 sans le symbole d'alerte de s6curit6, indique une situation
potentiellement dangereuse qui, si elle n'est pas 6vit6e, pourrait entraTner des
dommages materiels.

J

POUR TOUTE QUESTION OU REMARQUE AU SUJET DE CET OUTIL OU DE TOUT
AUTRE OUTIL DEWALT, COMPOSEZ LE NUMERO SANS FRAIS • 1-800-4-DEWALT
(1-800-433-9258).

_ VERTISSEMENT : afin de r6duire le risque de blessures, lire le mode d'emploi de

IbutiL

Avertissements de sdcuritd gdndraux pour les outils

dlectriques

_ AVERTISSEMENT! Life tousles avertissements de securite et toutes les directives.

Le non-respect des avertissements et des directives pourrait se solder par un choc
61ectrique, un incendie et/ou une blessure grave.

CONSERVER TOUS LES AVERTISSEMENTS ET TOUTES

LES DIRECTIVES POUR UN USAGE ULTERIEUR

Le terme _ outi161ectrique _, cit6 dans les avertissements se rapporte a votre outi161ectrique
alimentation sur secteur (avec ill) ou par piles (sans ill).

1) S#CURIT# DU LIEU DE TRAVAIL

a) Tenir I'aire de travail propre et bien eclairee. Les lieux encombr6s ou sombres sont

propices aux accidents.

b) Ne pas faire fonctionner d'outils electriques clans un milieu deflagrant, tel qu'en

presence de liquides, de gaz ou de poussieres inflammables. Les outils 61ectriques
produisent des 6tincelles qui pourraient enflammer la poussibre ou les vapeurs.

c) Eloigner les enfants et les personnes a proximite pendant I'utilisation d'un outil

electrique. Une distraction pourrait en faire perdre la mMtrise a I'utilisateur.

2) SI_CURITI_ EN MATIERE D'I_LECTRICITI_

a) Les fiches des outils electriques doivent correspondre a la prise. Ne jamais

modifier la fiche d'aucune faFon. Ne jamais utiliser de fiche d'adaptation avec un
outil electrique mis a la terre. Le risque de choc 61ectrique sera r6duit par I'utilisation de
fiches non modifi#es correspondant a la prise.

b) E:viter tout contact physique avec des surfaces mises a la terre comme des tuyaux,

des radiateurs, des cuisinieres et des refrigerateurs. Le risque de choc #lectrique est
plus #lev# si votre corps est mis a la terre.

c) Ne pas exposer les outils electriques a la pluie ou a I'humidite. La p#n#tration de

I'eau dans un outil #lectrique augmente le risque de choc #lectrique.

d) Ne pas utiliser le cordon de faFon abusive. Ne jamais utiliser le cordon pour

transporter, tirer ou debrancher un outil electrique. Tenir le cordon eloigne de
la chaleur, de I'huile, des bords tranchants et des pieces mobiles. Les cordons
endommag#s ou enchev#tr#s augmentent les risques de choc #lectrique.

e) Pour I'utilisation d'un outil electrique a I'exterieur, se servir d'une rallonge

convenant a cette application. L'utilisation d'une rallonge con_ue pour I'ext#rieur r#duira
les risques de choc #lectrique.

f) S'il est impossible d'eviter I'utilisation d'un outil electrique clans un endroit

humide, brancher I'outil clans une prise ou sur un circuit d'alimentation dotes d'un
disjoncteur de fuite a la terre (GFCl). L'utilisation de ce type de disjoncteur r#duit les
risques de choc #lectrique.

3) SI_CURITI_ PERSoNNELLE

a) F:tre vigilant, surveiller le travail effectue et faire preuve de jugement Iorsqu'un outil

electrique est utilise. Ne pas utiliser d'outil electrique en cas de fatigue ou sous
I'influence de drogues, d'alcool ou de medicaments. Un simple moment d'inattention
en utilisant un outil #lectrique peut entrafner des blessures corporelles graves.

b) Utiliser des equipements de protection individuelle. Toujours porter une protection

oculaire. L'utilisation d'#quipements de protection comme un masque antipoussibre, des
chaussures antid#rapantes, un casque de s#curit# ou des protecteurs auditifs Iorsque la
situation le requiert r#duira les risques de blessures corporelles.

c) EmpOcher les demarrages intempestifs. S'assurer que I'interrupteur se trouve a la

position d'arrOt avant de relier I'outil a une source d'alimentation et/ou d'inserer un
bloc-piles, de ramasser ou de transporter I'outil. Transporter un outi/ #/ectrique a/ors
que le doigt repose sur I'interrupteur ou brancher un outil _lectrique dont I'interrupteur est

la position de marche risque de provoquer un accident.

d) Retirer toute cle de reglage ou cle avant de demarrer I'outil. Une cl# ou une cl# de

r#glage attach#e a une partie pivotante de I'outil #lectrique peut provoquer des blessures
corporelles.

e) Ne pas trop tendre les bras. Conserver son equilibre en tout temps. Cela permet de

mieux mMtriser I'outil #lectrique dans les situations impr#vues.

f) S'habiller de maniere appropriee. Ne pas porter de vOtements amples ni de bijoux.

Garder les cheveux, les vOtements et les gants a I'ecart des pieces mobiles. Les

v_tements amples, les bijoux ou les cheveux longs risquent de rester coinc_s dans les

pibces mobiles.

g) Sides composants sont fournis pour le raccordement de dispositifs de depoussierage

et de ramassage, s'assurer que ceux-ci sont bien raccordes et utilises. L'utilisation
d'un dispositif de d#poussi#rage peut r#duire les dangers engendr#s par les poussibres.

4) UTILISATION ET ENTRETIEN D'UN OUTIL #LECTRIQUE

a) Ne pas forcer un outil electrique. Utiliser I'outil electrique approprie a I'application.

L'outil #lectrique appropri# effectuera un meilleur travail, de fa_on plus sore eta la vitesse
pour laquelle il a#t# congu.

b) Ne pas utiliser un outil electrique dont I'interrupteur est defectueux. Tout outil

#lectrique dont I'interrupteur est d#fectueux est dangereux et doit _tre r#par#.

c) Debrancher la fiche de la source d'alimentation et/ou du bloc-piles de I'outil

electrique avant de faire tout reglage ou changement d'accessoire ou avant de
ranger I'outil. Ces mesures preventives r#duisent les risques de d#marrage accidentel
de I'outil #lectrique.

d) Ranger les outils electriques hors de la portee des enfants et ne permettre

aucune personne n'etant pas familiere avec un outil electrique ou son mode
d'emploi d'utiliser cet outil. Les outils #lectriques deviennent dangereux entre les mains
d'utilisateurs inexp#riment#s.

e) Entretien des outils electriques. Verifier si les pieces mobiles sont mal alignees ou

coincees, si des pieces sont brisees ou presentent toute autre condition susceptible
de nuire au bon fonctionnement de I'outil electrique. En cas de dommage, faire
reparer I'outil electrique avant toute nouvelle utilisation. Beaucoup d'accidents sont
causes par des outils #lectriques mal entretenus.

f) S'assurer que les outils de coupe sont aiguises et propres. Les outils de coupe

bien entretenus et affDt#s sont moins susceptibles de se coincer et sont plus faciles
ma ftrise r.

g) Utiliser I'outil electrique, les accessoires, les forets, etc. conformement aux

presentes directives en tenant compte des conditions de travail et du travail
effectuer. L'utilisation d'un outil #lectrique pour toute operation autre que celle pour
laquelle il a#t# con_u est dangereuse.

5) UTILISATION ET ENTRETIEN DU BLOC-PILES

a) Ne recharger I'outil qu'au moyen du chargeur precise par le fabricant. L'utilisation

d'un chargeur qui convient a un type de bloc-piles risque de provoquer un incendie s'il est
utilis# avec un autre type de b Ioc-piles.

b) Utiliser les outils electriques uniquement avec les blocs-piles conFus a cet effet.

L'utilisation de tout autre bloc-piles risque de causer des blessures ou un incendie.

c) Lorsque le bloc-piles n'est pas utilise, le tenir eloigne des objets metalliques,

notamment des trombones, de la monnaie, des cles, des clous, des vis ou autres

petits objets metalliques qui peuvent etablir une connexion entre les deux bornes.
Le court-circuit des bornes du bloc-piles risque de provoquer des brEflures ou un
incendie.

d) En cas d'utilisation abusive, le liquide peut gicler hors du bloc-piles; eviter tout

contact avec ce liquide. Si un contact accidentel se produit, laver a grande eau. Si
le liquide entre en contact avec les yeux, obtenir egalement des soins medicaux. Le

liquide qui gicle hors du bloc-piles peut provoquer des irritations ou des brE_lures.

6) R#PARATION

a) Faire reparer I'outil electrique par un reparateur professionnel en n'utilisant que des

pieces de rechange identiques. Ce/a permettra de maintenir une uti/isation s_curitaire
de I'outil _lectrique.

R_gles de s_curit_ particuli_res

• Tenir I'outil par les surfaces de saisie isolees pour les travaux ob I'outil de coupe
risque de toucher a des ills dissimules. Tout contact avec un fil "sous tension" provoquera

"l'#lectrisation" des parties m#talliques expos#es et I'#lectrocution de I'utilisateur.

• Utiliser des brides de fixation ou tout autre dispositif de fixation permettant de soutenir
et de retenir la piece sur une plate-forme stable. Tenir la pibce avec la main ou contre son
corps est instable et risque de provoquer une perte de maftrise de I'outiL

• Toujours porter des lunettes de protection ou toute autre protection oculaire. Lots du
martelage ou du per_age, des d#bris sont rejet#s dans I'air. Ces derniers peuvent causer des
dommages oculaires permanent.

• Meches, douilles ou outils peuvent chauffer pendant leur utilisation. Toujours porter des
gants avant de les manipuler.

• Ne pas utiliser cet outil pendant des periodes prolongees. Les vibrations caus_es par
I'outil peuvent poser des risques pour les mains ou les bras. Porter des gants pour amortir les

vibrations, et pour limiter les risques faire des pauses fr#quentes.
_&AVERTISSEMENT : TOUJOURS porter des lunettes de s#curit#. Les lunettes de vue
ne constituent PAS des lunettes de s#curit#. Utiliser #galement un masque facial ou anti-
poussibre si I'op#ration de d#coupe g#nbre de la poussibre. TOUJOURS UTILISER DE

L'EQUIPEMENT DE PROTECTION HOMOLOGUE :

• protection oculaire conforme a la norme ANSI Z87.1 (CAN/CSA Z94.3),

• protection auditive conforme a la norme ANSI $12.6 ($3.19) et

• protection des voies respiratoires conformes aux normes NIOSH/OSHA.
_AVERTISSEMENT : Certaines poussibres cr##es par le pon_age, le sciage, le meulage et
le forage m#caniques ainsi que d'autres activit#s de construction contiennent des produits
chimiques reconnus pour causer le cancer, des anomalies cong#nitales ou d'autres anomalies
li#es a la reproduction. Parmi ces produits chimiques, citons notamment :

• le plomb provenant des peintures au plomb ;

• la silice cristalline provenant des briques, du b#ton et d'autres mat#riaux de

ma_onnerie ;

• I'arsenic et le chrome provenant du bois trait# (ars#niate de cuivre et de chrome).
Le risque associ# aces expositions varie selon la fr#quence de ces types de travaux. Pour
r#duire I'exposition aux produits chimiques : travailler dans un local bien ventil# et utiliser du
materiel de s#curit# approuv#, comme les masques antipoussibres sp#cialement con_us pour
filtrer les particules microscopiques.

• Eviter le contact prolonge avec la poussiere provenant du ponFage, du sciage, du

meulage et du forage mecanique ainsi que d'autres activites de construction. Porter
des v_tements de protection et laver lee parties exposees au savon et a I'eau. La

poussibre qui pourrait p_n_trer clans la bouche et les yeux ou se d_poser sur la peau peut

favoriser I'absorption de produits chimiques nocifs.
_&AVERTISSEMENT : Cet outil peut produire et r#pandre de la poussibre susceptible de
causer des dommages s#rieux et permanents au systbme respiratoire. Toujours utiliser un
appareil respiratoire anti-poussibres approuv# par le NIOSH ou I'OSHA. Diriger les particules
dans le sens oppos# du visage et du corps.
_AVERTISSEMENT : TOUJOURS porter une protection auditive appropriee conformement

la norme ANSI $12.6 (S3.19) Iors de I'utilisation du produit. Dans certaines conditions et

selon la dur#e d'utilisation, le bruit #mis par ce produit peut contribuer a une perte auditive.

_ATTENTION : Apres utilisation, ranger I'outil sur son cote sur une surface stable la ob
il ne pourra faire ni trebucher ni tomber personne. Certains outils _quip_s d'un large bloc-

pile peuvent tenir a la verticale sur ce dernier mais ils sont alors facilement d_stabilis_s.

• L'#tiquette appos#e sur votre outil peut comprendre les symboles suivants. Les symboles et

leurs d#finitions sont indiqu#s ci-aprbs :

V.................. volts

Hz................ hertz

min .............. minutes

.... ........... courant continu

@ ................ Construction de classe I

(mis a la terre)

[] ................ Construction de classe II

(a double isolation)

RPM ............ rotations ou alternance

par minute

A................. ampbres

W................ watts

"_ .............. courant alternatif

_-, .............. courant alternatif ou continu

no ............... vitesse a vide

................ borne de terre

i_, ............... symbole d'alerte a la s#curit#

BPM ........... coups par minute

.../min ......... par minute

IPM ............. impacts par minute

Directives de sdcuritd importantes pour tous
les blocs-piles

Pour la commande d'un bloc-piles de rechange, s'assurer d'inclure le num6ro de catalogue
et la tension. Consulter le tableau figurant & la fin du pr6sent mode d'emploi pour connaftre la
compatibilit6 des chargeurs et des blocs-piles.
Le bloc-piles n'est pas compl_tement charg6 & la sortie de I'emballage. Avant d'utiliser le bloc-
piles et le chargeur, lire les directives de s6curit6 ci-apr_s. Respecter ensuite les consignes de
chargement d6crites.

LIRE TOUTES LES DIRECTIVES

• Ne pas charger ou utiliser un bloc-piles clans un milieu deflagrant, en presence

de liquides, de gaz ou de poussiere inflammables. InsUrer ou retirer un bloc-piles du

chargeur peut enflammer de la poussibre ou des _manations.

• NE JAMAIS forcer I'insertion d'un bloc-piles clans le chargeur. Ne pas modifier un

bloc-piles de quelque faFon que ce soit pour I'inserer clans un chargeur incompatible,

car il risque de se rompre et de provoquer de graves blessures corporelles. Consulter

le tableau figurant a la fin du present manuel pour connaftre la compatibilit# des piles et des

chargeurs.

• Charger les blocs-piles uniquement au moyen de chargeurs DEWALT.

• NE PAS #clabousser le bloc-piles ni I'immerger dans I'eau ou dans tout autre liquide.

• Ne pas ranger ni utiliser I'outil et le bloc-piles a un endroit ob la temperature peut

atteindre ou depasser les 40 °C (105 °F) (comme clans les remises exterieures ou les

b&timents metalliques I'ete).

,&DANGER : Risque d'_lectrocution. Ne jamais ouvrir le bloc-piles pour quelque raison que
ce soit. Si le bo#ier du bloc-piles est fissur# ou endommag#, ne pas I'ins#rer clans un chargeur.
Ne pas #craser, faire tomber ou endommager le bloc-piles. Ne pas utiliser un bloc-piles ou un
chargeur qui a regu un choc violent, qui est tomb#, a #t# #cras# ou est endommag# de quelque
manibre que ce soit (p. ex. perc# par un clou, frapp# d'un coup de marteau, pitting). En effet,
il y a risque de choc #lectrique ou d'#lectrocution. Les blocs-piles endommag#s doivent 6tre
envoy#s au centre de r#paration pour 6tre recycles.

REMARQUE : un boftier sp6cial et des capuchons de s6curit6 sont fournis
avec le bloc-piles pour utilisation chaque fois qu'on le retire de I'outil ou du
chargeur pour le ranger ou le transporter. Enlever le capuchon avant de remettre
le bloc-piles dans le chargeur ou I'outil.
_AVERTISsEMENT : Risque d'incendie. Ne pas ranger ni ne transporter les piles de

maniere a ce que des objets metalliques puissent entrer en contact avec les bornes
exposees des piles. On ne doit pas mettre, par exemple, le bloc-piles sans capuchon clans
un tablier, une poche, une bofte a outils, une bofte de n#cessaire de produit, un tiroir, etc. avec
des clous, des vis, des cl#s, etc. Le transport des piles peut causer un incendie si les
bornes des piles entrent en contact involontairement avec des matieres conductrices
comme des cles, de la monnaie, des outils manuels et d'autres elements semblables. La
Hazardous Material Regulations (r#glementation sur les produits dangereux) du d#partement
am#ricain des transports interdit en fait le transport des blocs-piles pour le commerce et dans les
avions (c.-a-d. clans des valises et les bagages a main) A MOINS qu'ils ne soient bien proteges
contre les courts-circuits. Pour le transport de piles individuelles, on doit donc s'assurer que les
bornes sont protegees et bien isol#es contre toute matibre pouvant entrer en contact avec elles
et provoquer un court-circuit.