Desa CDCFTP User Manual

UNVENTED (VENT-FREE) GAS COMPACT CLASSIC HEARTH®

DUAL BURNER FIREPLACE

OWNER’S OPERATION AND INSTALLATION MANUAL

Shown with Optional Cabinet Mantel/Hearth Base Accessory

THERMOSTAT MODELS

CDCFTN, CDCFTP, VDCFTN, VDCFTP, FDCFTN, FDCFTP

REMOTE-READY MODELS

VDCFRN, VDCFRP, FDCFRN, FDCFRP, CDCFNR, CDCFPR

WARNING: If the information in this manual is not followed exactly, a ﬁre or explosion may result causing property damage, personal injury, or loss of life.

— Do not store or use gasoline or other ﬂammable

vapors and liquids in the vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

•

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁre department.

—

Installation and service must be performed by a qualiﬁed installer, service agency, or the gas supplier.

Save this manual for future reference.

For more information, visit www.desatech.com

WARNING: Improper installation, adjustment, alteration, service, or maintenance can cause injury or property damage. Refer to this manual for correct installation and operational procedures. For assistance or additional information consult a qualiﬁed installer, service agency, or the gas supplier.

WARNING: This is an unvented gas-ﬁred heater. It uses air (oxygen) from the room in which it is installed. Provisions for adequate combustion and ventilation air must be provided. Refer to Air for Combustion and Ventilation section on page 6 of this manual.

This appliance may be installed in an aftermarket,* permanently located, manufactured (mobile) home, where not prohibited by local codes.

This appliance is only for use with the type of gas indi cated on the rating plate. This appliance is not convertible for use with other gases.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

TABLE OF CONTENTS

Safety Information ............................................... 3

Product Identiﬁcation ...........................................

Optional Remote Control Accessories .................

Local Codes ........................................................ 5

Product Features ................................................. 5

Unpacking ........................................................... 5

Hood Assembly ...................................................

Air for Combustion and Ventilation ......................

Installation ........................................................... 9

Operating Fireplace ........................................... 22

Inspecting Burners ............................................ 27

Cleaning and Maintenance ................................ 28

Wiring Diagram .................................................. 29

Troubleshooting .................................................

Speciﬁcations ....................................................

Replacement Parts ............................................ 35

Service Hints ..................................................... 35

Technical Service ..............................................

Illustrated Parts Breakdown and Parts List ....... 36

Accessories ....................................................... 44

30 34

www.desatech.com

111244-01D

SAFETY INFORMATION

WARNING: This product contains and/or generates chemicals known to the State of California to cause cancer or birth defects, or other reproductive harm.

IMPORTANT: Read this owner’s manual carefully and completely before trying to assemble, operate, or service this ﬁreplace. Improper use of this ﬁreplace can cause serious injury or death from burns, fire, explosion, electrical shock, and carbon monoxide poisoning.

DANGER: Carbon monoxide poisoning may lead to death!

Carbon Monoxide Poisoning:

monoxide poisoning resemble the ﬂu, with head aches, dizziness, or nausea. If you have these signs, the ﬁreplace may not be working properly. Get fresh air at once! Have ﬁreplace serviced. Some people are more affected by carbon monoxide than others. These include pregnant women, people with heart or lung disease or anemia, those under the inﬂuence of alcohol, and those at high altitudes.

Natural and Propane/LP Gas: Natural and pro-

pane/LP gases are odorless. An odor-making agent is added to the gas. The odor helps you detect a gas leak. However, the odor added to the gas can fade. Gas may be present even though no odor exists.

Make certain you read and understand all warnings. Keep this manual for reference. It is your guide to safe and proper operation of this ﬁreplace.

Early signs of carbon

WARNING: Do not allow fans to blow directly into the ﬁreplace. Avoid any drafts that alter burner ﬂame patterns. Ceiling fans can create drafts that alter burner ﬂame patterns. Altered burner patterns can cause sooting.

Due to high temperatures, the appliance should be located out of trafﬁc and away from furniture and draperies.

Do not place clothing or other ﬂammable material on or near the appliance. Never place any objects on the heater.

Fireplace front and screen become very hot when running heater. Keep children and adults

away from hot surfaces to avoid burns or clothing ignition. Fireplace will remain hot for a time after shutdown. Allow surfaces to cool before touching.

Carefully supervise young children when they are in the room with ﬁreplace. When using the hand-held remote accessory (Remote-Ready Models Only), keep selector switch in the OFF position to prevent children from turning on burners with remote.

WARNING: Any change to this ﬁreplace or its controls can be dangerous.

You must operate this ﬁreplace with the ﬁreplace screen in place. Make sure ﬁreplace screen is closed before running ﬁreplace.

WARNING: Do not use a blower insert, heat exchanger insert, or other accessory not approved for use with this ﬁreplace.

111244-01D 3

www.desatech.com

Keep the appliance area clear and free from combustible ma terials, gasoline, and other ﬂam mable vapors and liquids.

SAFETY INFORMATION

Continued

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.

2. Do not place propane/LP supply tank(s) inside any structure. Locate propane/LP supply tank(s) outdoors.

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not use

any phone in your building

• immediately call your gas supplier from a

neighborʼs phone. Follow the gas supplierʼs instructions

• if you cannot reach your gas supplier, call

the ﬁre department

4. This ﬁreplace shall not be installed in a bed room or bathroom.

5. Do not use this ﬁreplace as a wood-burning ﬁreplace. Use only the logs provided with the ﬁreplace.

6. Do not add extra logs or ornaments such as pine cones, vermiculite, or rock wool. Using these added items can cause sooting. Do not add lava rock around base. Rock and debris could fall into the control area of ﬁreplace.

7. This ﬁreplace is designed to be smokeless. If logs ever appear to smoke, turn off ﬁreplace and call a qualiﬁed service person. Note: During initial operation, slight smoking could occur due to log curing and ﬁreplace burning manufacturing residues.

8. To prevent the creation of soot, follow the instructions in Cleaning and Maintenance, page 28.

9. Before using furniture polish, wax, carpet cleaner, or similar products, turn ﬁreplace off. If heated, the vapors from these products may create a white powder residue within burner box or on adjacent walls or furniture.

10. This ﬁreplace needs fresh air ventilation to run properly. This ﬁreplace has an Oxygen Deple tion Sensing (ODS) safety shutoff system. The ODS shuts down the ﬁreplace if not enough fresh air is available. See Air for Combustion and Ventilation, page 6. If ﬁreplace keeps shutting off, see Troubleshooting, page 30.

11. Do not run ﬁreplace

• where ﬂammable liquids or vapors are used

or stored.

• under dusty conditions.

www.desatech.com

12. Do not use this ﬁreplace to cook food or burn paper or other objects.

13. Never place any objects in the ﬁreplace or on logs.

14. Do not use ﬁreplace if any part has been under water. Immediately call a qualiﬁed service technician to inspect the room ﬁreplace and to replace any part of the control system and any gas control which has been under water.

15. Turn off and unplug ﬁreplace and let cool before servicing. Only a qualiﬁed service person should service and repair ﬁreplace.

16. Operating ﬁreplace above elevations of 4,500 feet could cause pilot outage.

17. Do not operate ﬁreplace if log is broken. Do not operate ﬁreplace if log is chipped (dimesized or larger).

18.

To prevent performance problems, do not use propane/LP fuel tank of less than 100 lbs. capacity.

19. Prov ide adeq ua te clearan ce s around air openings.

PRODUCT

IDENTIFICATION

Fireplace Cabinet

Hood

Screen

Log

Ignitor Button

Fireplace

Hood

Logs

Ignitor Button

Remote Control (Optional)

Control Knob

Figure 1 - Vent-Free Compact Dual Flame

Fireplace

Cabinet

111244-01D

Control Knob

OPTIONAL REMOTE

CONTROL ACCESSORIES

(For Remote-Ready Models Only)

There are four optional remote controls that can be purchased separately for Remote-Ready Models only:

• wall switch •

• wall thermostat

See Accessories, page 44.

hand-held ON/OFF remote

• hand-held thermostat remote

LOCAL CODES

Install and use ﬁreplace with care. Follow all local codes. In the absence of local codes, use the lat est edition of The National Fuel Gas Code ANSI

Z223.1/NFPA 54

*Available from:

American National Standards Institute, Inc.

National Fire Protection Association, Inc.

1430 Broadway

New York, NY 10018

Batterymarch Park

Quincy, MA 02269

PRODUCT FEATURES

SAFETY PILOT

This ﬁreplace has a pilot with an Oxygen Depletion Sensing (ODS) safety shutoff system. The ODS/pilot is a required feature for vent-free room ﬁreplaces. The ODS/pilot shuts off the ﬁreplace if there is not enough fresh air.

PIEZO IGNITION SYSTEM

This ﬁreplace has a piezo ignitor. This system requires no matches, batteries, or other sources to light ﬁreplace.

THERMOSTATIC HEAT CONTROL FOR THERMOSTAT-CONTROLLED MODELS

Thermostat-Controlled models have a thermostat sensing bulb and a control valve. The thermostat will automatically modulate the heat output to maintain a consistent room temperature. This results in greater ﬁreplace comfort. This can also result in lower gas bills.

UNPACKING

WARNING: Ceramic brick liners for Models CDCFNR and CDCFPR are located behind upper louver and must be removed before lighting ﬁreplace.

1. Remove fireplace and hood from carton. Log is wrapped and inside ﬁreplace. Do not remove at this time.

2. Remove all protective packaging applied to ﬁreplace for shipment.

3. Make sure your ﬁreplace includes one hard ware packet.

4. Check ﬁreplace for any shipping damage. If ﬁreplace is damaged, promptly inform dealer where you bought ﬁreplace.

Models CDCFNR/PR only

1. Remove screws from top louver and carefully remove louver (see Figure 2).

2. Remove ceramic brick liners with protective packaging. The brick liners will be installed later.

3. Remove yellow sticker from top of ﬁrebox.

4. Replace top louver using screws removed in step 1.

Wrapped Brick Liners

Top Louver

Screws

Figure 2 - Removing Brick Liners From

CDCFNR/PR

111244-01D 5

www.desatech.com

HOOD ASSEMBLY

WARNING: Always have screen in place before operating ﬁreplace. This prevents excessive temperatures on ﬁreplace surfaces.

WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts speciﬁcally approved with this ﬁreplace may result in property damage or personal injury.

Tools Required:

• Phillips screwdriver • slotted screwdriver

• 5/16" hex wrench • scissors

1. Models with one-piece screen only: Lift ﬁreplace screen up and pull out to remove (see Figure 3). Set screen aside until installation has been completed.

2. Cut two plastic straps to remove the log from the ﬁrebox cavity. Set log aside.

3. An optional blower is available. See sories, page 44. Install optional blower now. Follow installation instructions provided with blower and see page 14 or 15, depending on your installation.

4. Locate four black phillips sheet metal screws in hardware packet.

5. Slide hood between louver and ﬁrebox top and align screw holes.

6. Insert screws as shown in Figure 4. Tighten screws ﬁrmly.

Shoulder Screw

Screen

Acces-

Sheet Metal Screws

Hood

Figure 4 - Assembling Hood

Louver

Firebox Top

AIR FOR COMBUSTION

AND VENTILATION

WARNING: This ﬁreplace shall not be installed in a conﬁned space or unusually tight construction unless provisions are provided for adequate combustion and ventilation air. Read the following instructions to in sure proper fresh air for this and other fuel-burning appliances in your home.

Todayʼs homes are built more energy efﬁcient than ever. New materials, increased insulation, and new construction methods help reduce heat loss in homes. Home owners weather strip and caulk around windows and doors to keep the cold air out and the warm air in. During heating months, home owners want their homes as airtight as possible.

While it is good to make your home energy efﬁ cient, your home needs to breathe. Fresh air must enter your home. All fuel-burning appliances need fresh air for proper combustion and ventilation.

Exhaust fans, ﬁreplaces, clothes dryers, and fuel burning appliances draw air from the house to operate. You must provide adequate fresh air for these appliances. This will insure proper venting of vented fuel-burning appliances.

Figure 3 - Removing and Installing

Screen

www.desatech.com

111244-01D

AIR FOR COMBUSTION

AND VENTILATION

Continued

PROVIDING ADEQUATE VENTILATION

The following are excerpts from National Fuel Gas Code, ANSI Z223.1/NFPA 54, Section 5.3, Air for Combustion and Ventilation.

All spaces in homes fall into one of the three fol lowing ventilation classiﬁcations:

1. Unusually Tight Construction

2. Unconﬁned Space

3. Conﬁned Space

The information on pages 6 through 8 will help you classify your space and provide adequate ventilation.

Unusually Tight Construction

The air that leaks around doors and windows may provide enough fresh air for combustion and ventilation. However, in buildings of unusually tight construction, you must provide additional fresh air.

Unusually tight construction is deﬁned as construction where:

a. walls and ceilings exposed to the out

side atmosphere have a continuous water vapor retarder with a rating of one perm (6 x 10 less with openings gasketed or sealed and

b. weather stripping has been added on

openable windows and doors and

c. caulking or sealants are applied to

areas such as joints around window and door frames, between sole plates and ﬂoors, between wall-ceiling joints, between wall panels, at penetrations for plumbing, electrical, and gas lines, and at other openings.

If your home meets all of these three

criteria, you must provide additional fresh air. See Ventilation Air From Outdoors, page 8.

If your home does not meet all of the three criteria above, proceed to Determining Fresh-Air Flow For Fireplace Location.

Conﬁned and Unconﬁned Space

The National Fuel Gas Code, ANSI Z223.1/NFPA 54 deﬁnes a conﬁned space as a space whose

volume is less than 50 cubic feet per 1,000 Btu per hour (4.8 m

-11

kg per pa-sec-m2) or

per kw) of the aggregate input

rating of all appliances installed in that space and an unconﬁned space as a space whose volume is not less than 50 cubic feet per 1,000 Btu per hour (4.8 m3 per kw) of the aggregate input rating of all appliances installed in that space. Rooms com municating directly with the space in which the appliances are installed*, through openings not furnished with doors, are considered a part of the unconﬁned space.

* Adjoining rooms are communicating only if

there are doorless passageways or ventilation grills

between them.

DETERMINING FRESH-AIR FLOW FOR FIREPLACE LOCATION

Determining if You Have a Conﬁned or Unconﬁned Space

Use this work sheet to determine if you have a conﬁned or unconﬁned space.

Space: Includes the room in which you will install ﬁreplace plus any adjoining rooms with doorless passageways or ventilation grills between the rooms.

1. Determine the volume of the space (length x

width x height).

Length x Width x Height =__________cu. ft.

(volume of space)

Example: Space size 16 ft. (length) x 14 ft.

(width) x 8 ft. (ceiling height) = 1792 cu. ft. (volume of space)

If additional ventilation to adjoining room is

supplied with grills or openings, add the volume of these rooms to the total volume of the space.

2. Multiply the space volume by 20 to determine

the maximum Btu/Hr the space can support.

__________ ( vo l u me o f s p ac e ) x 20 =

(Maximum Btu/Hr the space can support) Example: 1792 cu. ft. (volume of space) x 20 =

35,840 (maximum Btu/Hr the space can support)

3. Add the Btu/Hr of all fuel burning appliances in

the space.

Vent-free ﬁreplace ___________

Gas water heater* ___________

Gas furnace ___________

Vented gas heater ___________

Gas ﬁreplace logs ___________

Other gas appliances* + ___________

Total = ___________

* Do not include direct-vent gas appliances. Di

rect-vent draws combustion air from the outdoors and vents to the outdoors.

Example:

Gas water heater ___________

Vent-free ﬁreplace ___________

Total ___________

30,000

+ 10,000

= 40,000

Btu/Hr

111244-01D 7

www.desatech.com

Outlet Air

Ventilated Attic

Outlet

Inlet Air

Ventilated

Crawl Space

Crawl

Space

To Attic

Or Remove Door into Adjoining

Room, Option

Ventilation Grills

Into Adjoining Room,

Option 2

ntilation Grills

Into Adjoining

Room,

Option 1

12"

AIR FOR COMBUSTION

AND VENTILATION

Continued

4. Compare the maximum Btu/Hr the space can

support with the actual amount of Btu/Hr used.

_______

_______ Example: 35,840 Btu/Hr (maximum the space

40,000 Btu/Hr (actual amount of

The space in the above example is a conﬁned space because the actual Btu/Hr used is more than the maxi mum Btu/Hr the space can support. You must provide additional fresh air. Your options are as follows:

A. Rework worksheet, adding the space of an adjoin

ing room. If the extra space provides an unconﬁned space, remove door to adjoining room or add ventilation grills between rooms. See Ventilation

Air From Inside Building.

B. Vent room directly to the outdoors. See Ventila

tion Air From Outdoors.

C. Install a lower Btu/Hr ﬁreplace, if lower Btu/Hr

size makes room unconﬁned.

If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconﬁned space. You will need no additional fresh air ventilation.

which the ﬁreplace may be operated is smaller than that deﬁned as an unconﬁned space or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of the methods described in the National Fuel Gas Code,

ANSI Z223.1/NFPA 54 Section 5.3

or applicable local codes.

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining unconﬁned space. When ventilating to an adjoining unconﬁned space, you must provide two permanent openings: one within 12" of the ceiling and one within 12" of the ﬂoor on the wall connecting the two spaces (see options 1 and 2, Figure 5). You can also remove door into adjoining room (see option 3, Figure 5). Fol low the National Fuel Gas Code, ANSI Z223.1/NFPA

54, Section 5.3, Air for Combustion and Ventilation

for required size of ventilation grills or ducts.

Btu/Hr (maximum the space can support)

Btu/Hr (actual amount of Btu/Hr used)

can support)

Btu/Hr used)

WARNING: If the area in

www.desatech.com

Figure 5 - Ventilation Air from Inside

Building

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills or

ducts. You must provide two permanent openings: one within 12" of the ceiling and one within 12" of the ﬂoor. Connect these items directly to the outdoors or spaces open to the outdoors. These spaces include attics and crawl spaces. Follow the

National Fuel Gas Code, ANSI Z223.1/NFPA 54, Section 5.3, Air for Combustion and Ventilation for

required size of ventilation grills or ducts. IMPORTANT: Do not provide openings for inlet

or outlet air into attic if attic has a thermostatcontrolled power vent. Heated air entering the attic will activate the power vent.

Figure 6 - Ventilation Air from Outdoors

111244-01D

INSTALLATION

NOTICE: This heater is intended for use as supplemental heat. Use this heater along with your primary heating system. Do not install this heater as your pri mary heat source. If you have a central heating system, you may run system’s circulating blower while using heater. This will help circulate the heat throughout the house. In the event of a power outage, you can use this heater as your primary heat source.

WARNING: A qualiﬁed service person must install ﬁre place. Follow all local codes.

WARNING: Never install the ﬁreplace

• in a bedroom or bathroom

• in a recreational vehicle

• where curtains, furniture,

clothing, or other ﬂammable objects are less than 36 inches from the front, top, or sides of the ﬁreplace

• as a ﬁreplace insert

• in high trafﬁc areas

• in windy or drafty areas

WARNING: Never install in a bedroom or bathroom. Any heat ing product with a Btu/Hr rating over 10,000 cannot be used in a bedroom.

CAUTION: This ﬁreplace creates warm air currents. These currents move heat to wall surfaces next to ﬁreplace. Installing ﬁreplace next to vinyl or cloth

wall coverings or operating

ﬁreplace where impurities (such as, but not limited to, tobacco smoke, aromatic candles, cleaning ﬂuids, oil or kerosene lamps, etc.) in the air exist, may discolor walls or cause odors.

IMPORTANT: Vent-free ﬁreplaces add moisture to the air. Although this is beneﬁcial, installing ﬁreplace in rooms without enough ventilation air may cause mildew to form from too much moisture. See Air for

Combustion and Ventilation,

Note: Your ﬁreplace is designed to be used in zero clearance installations. Wall or framing material can be placed directly against any exterior surface on the rear, sides, or top of your ﬁreplace, except where standoff spacers are integrally attached. If standoff spacers are attached to your ﬁreplace, these spacers can be placed directly against wall or framing materials.

Note: When installing ﬁreplace directly on carpeting, tile or other combustible material, other than wood ﬂooring, the ﬁreplace shall be installed on a metal or wood panel extending the full width and depth of the ﬁreplace.

Use the dimensions shown for rough openings to create the easiest installation (see Built-In Fire place Installation, page 10).

CHECK GAS TYPE

Use the correct gas type (natural or propane/LP) for your unit. If your gas supply is not correct, do not install ﬁreplace. Call dealer where you bought

ﬁreplace for proper type ﬁreplace.

page 6.

WARNING: This appliance is equipped for (natural or propane/LP) gas. Field conversion is not permitted.

111244-01D 9

www.desatech.com

INSTALLATION

Continued

INSTALLATION ITEMS

Before installing ﬁreplace, make sure you have the items listed below.

• external regulator (supplied by installer, for propane/LP units only)

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• equipment shutoff valve *

• test gauge connection*

• ground joint union

• sediment trap

• tee joint

• pipe wrench

* A CSA design-certiﬁed equipment shutoff valve with 1/8” NPT tap is an acceptable alternative to test gauge connection. Purchase the optional CSA design-certiﬁed equipment shutoff valve from your dealer. See Accessories, page 44.

Note: If desired, purchase a four-sided brass trim kit for built-in installations. See Accessories, page 44.

FIREPLACE CLEARANCES

WARNING: Maintain the minimum clearances shown in Figure 7. If you can, provide greater clearances from ﬂoor, ceiling, and joining wall.

If your ﬁreplace is to be used with an optional mantel, the installation instructions included with your mantel shows an CSA approved method of attaching the ﬁreplace/mantel system to a wall. IMP ORTANT: Only use optional cabinet or corner mantels speciﬁed in this manual. Purchase the optional mantel from your dealer (see sories, page 44).

If your ﬁreplace is to be recessed into the wall, see Built-In Fireplace Installation to secure your ﬁreplace into the wall.

CAUTION: If you install the ﬁreplace in a home garage

• ﬁreplace pilot and burner must

be at least 18 inches above ﬂoor.

• locate ﬁreplace where moving

vehicle will not hit it.

Acces-

For convenience and efﬁciency, install ﬁreplace

• where there is easy access for operation, inspec tion, and service

• in coldest part of room

An optional blower kit is available from your dealer. See Accessories, page 44. If planning to use blower, follow instructions provided with blower for power source.

Minimum Clearances For Side Combustible Material, Side Wall, and Ceiling

A. Clearances from the side of the fireplace

cabinet to any combustible material and wall should follow diagram in Figure 7.

Example: The face of a mantel, bookshelf,

etc. is made of combustible material and protrudes 3 1/2" from the wall. This combustible material must be 4" from the side of the ﬁreplace opening (see Figure 7).

Clearances from the top of the ﬁreplace opening to the ceiling should not be less than 36 inches.

For mantel clearances, see Figure 11, page 12.

MINIMUM CLEARANCE TO

COMBUSTIBLE MATERIALS

Top Left and Bottom Right Sides and Rear

36" 6" 0"

Example

*Minimum 16 inches from Side Wall

Figure 7 - Minimum Clearance for

Combustible to Wall

BUILT-IN FIREPLACE INSTALLATION

Built-in installation of this fireplace involves installing ﬁreplace into a framed-in enclosure. This makes the front of ﬁreplace ﬂush with wall. An optional brass trim kit accessory is available (see Accessories, page 44). Brass trim will extend past sides of ﬁreplace approximately 1/2 inch. This will cover the rough edges of the wall opening. If installing a built-in mantel above the ﬁreplace, you must follow the clearances shown in Figure 12, page 12. Follow the instructions below to install the ﬁreplace in this manner.

www.desatech.com

111244-01D

INSTALLATION

16"

3/4" Off The Floor Minimum

Continued

Actual Framing Height 26" 26

Front Width 26 Depth 14

Frame in rough opening. Use dimensions shown

/4" 26 7/8"

/4" 15 1/4"

in Figure 8 for the rough opening. If installing in a corner, use dimensions shown in Figure 10 for the rough opening. The height is 26 which is the same as the wall opening above.

2. If installing GA3450TA blower accessory, do so at this time. Follow instructions included with blower accessory.

Note: If not installing blower accessory, you

may wish to run electrical wiring to your ﬁreplace for future blower installation (see Accessories, page 44). Use only approved three-wire electrical wiring.

WARNING: If pre-wiring, do not connect wiring to any electrical source at this time.

Install ﬁreplace electrical outlet and connect wiring to outlet before connecting to electrical source. The ﬁreplace electrical outlet is included with the GA3450TA blower accessory.

Only use the ﬁreplace electrical outlet supplied with the GA3450TA blower accessory.

/8"

Note: A qualiﬁed installer should make all electrical connections.

3. Install gas piping to ﬁreplace location. This installation includes an approved ﬂexible gas line (if allowed by local codes) after the equip ment shutoff valve. The ﬂexible gas line must be the last item installed on the gas piping.

4. If you have not installed hood, follow instruc tions on page 6.

5. Carefully set ﬁreplace in front of rough opening with back of ﬁreplace inside wall opening.

6. Attach ﬂexible gas line to ﬁreplace gas regula tor. See Connecting Equipment Shutoff Valve

to Heater Control,

page 17.

7. Bend four nailing ﬂanges on outer casing with pliers (see Figure 10).

Attach ﬁreplace to wall studs using nails or wood screws through holes in nailing ﬂange.

Check all gas connections for leaks. See Check- ing Gas Connections, page 17.

10. If using optional brass trim kit, install the trim after ﬁnal ﬁnishing and/or painting of wall. See instructions included with brass trim ac cessory for attaching brass trim.

IMPORTANT:

When finishing your firebox,

combustible materials such as wall board, gypsum board, sheet rock, drywall, plywood, etc. may be butted up next to the sides and top edge of the ﬁrebox. Combustible materials should never overlap the ﬁrebox front facing.

WARNING: Do not allow any combustible materials to overlap the ﬁrebox front facing.

IMPORTANT: Noncombustible materials such as brick, tile, etc. may overlap the front facing, but should never cover any necessary openings like louvered slots.

Wall Studs

Figure 8 - Rough Opening for Installing

in Wall

Nails or Wood Screws

Figure 9 - Rough Opening for Installing

111244-01D 11

in Corner

www.desatech.com

Figure 10 - Attaching Fireplace to Wall

Studs

Nailing Flanges

INSTALLATION

15"

18"

21"

23"

2 1/2"

10"

Note:

All vertical measurements are from top of fireplace opening to bottom of mantel shelf. All measurements are in inches.

Continued

WARNING: Do not allow noncombustible materials to cover any necessary openings like louvered slots.

WARNING: Never modify or cover the louvered slots on the front of the ﬁrebox.

WARNING: Use only noncombustible mortar or adhesives when overlapping the front facing with noncombustible facing material.

Mantel Clearances for Built-In Installation

If placing mantel above built-in ﬁreplace, you must meet minimum clearance between mantel shelf and top of ﬁreplace opening.

NOTICE: Surface temperatures of adjacent walls and mantels become hot during operation. Walls and mantels above the ﬁrebox may become hot to the touch. If installed properly, these temperatures meet the requirement of the national product standard. Follow all minimum clearances shown in this manual.

Mantel Shelf

NOTICE: If your installation does not meet the minimum clear

ances shown, you must do one of the following:

• raise the mantel to an accept-

able height

• remove the mantel

OPTIONAL MANTEL INSTALLATION

Note: Refer to instructions provided with the mantel for assembly instructions. Refer to the following instructions for system installation. Refer to instructions on page 6 for hood assembly. Blower accessory should be installed if it is being used (see Installing Optional Blower Accessory

GA3450TA,

1. Unscrew four screws that attach top louver to

2. Place base assembly next to wall at installation

4. Place mantel around ﬁreplace on base (see

5. Assemble perimeter trim kit. See

6. Firmly snap perimeter trim kit on shoulder

7. Align perimeter trim kit for ﬂush ﬁt around

8. Center mantel left to right on base making sure

page 13).

ﬁreplace. Remove louver from ﬁreplace and set aside (see Figure 12).

location.

Place ﬁreplace on wood base (see Figure 13, page 13).

Figure 13, page 13).

Assembling

Perimeter Trim,

page 13.

screws. Shoulder screws are located on ﬁre place cabinet (see Figure 13, page 13).

opening.

mantel is ﬂush against wall.

Side of Firebox

Figure 11 - Minimum Mantel Clearances

for Built-In Installation

www.desatech.com

Top Louver

Bottom Louver

Figure 12 - Removing Top Louver and

Opening Bottom Louver

111244-01D

16.

INSTALLATION

Continued

9. Use two 3" wood screws provided and attach base of ﬁreplace to wooden mantel base (see Figure 13).

10. Remove perimeter trim kit and mantel. Be careful not to damage wall or mantel.

11. Cut an access hole in base to run ﬂexible gas line to ﬁreplace (see Figure 13). Make sure to locate access hole so mantel will cover it when installed. ﬂoor using wood screws. Countersink screw heads and putty over.

12. Install gas line. See Connecting To Gas Sup ply, page 16.

13. Check for leaks. See Checking Gas Connec tions, page 17.

14. Place mantel around ﬁreplace. Be careful not to damage wall or mantel.

15. Place perimeter trim kit on the shoulder screws located on the side and top of the ﬁreplace. Firmly snap trim over shoulder screws on ﬁreplace (see Figure 13).

Note: You can secure base to

Adjust assembly to remove any gaps. Attach remaining two 3" wood screws from hardware pack through openings inside of ﬁreplace sides into the mantel. The openings are located at top behind the area for top louver (see Figure 13).

17. Reinstall top louver.

Assembling Perimeter Trim (Perimeter trim shipped with mantel)

1. Remove packaging from three remaining pieces of trim.

2. Locate two adjusting plates with set screws, and two shims in the hardware packet.

3. Align shim under adjusting plate as shown in Figure 14.

Slide one end of adjusting plate/shim in slot on mitered edge of top brass trim (see Figure 14).

5. Slide other end of adjusting plate/shim in slot on mitered edge of side perimeter trim (see Figure 14).

6. While ﬁrmly holding edges of perimeter trim together, tighten both set screws on the adjust ing plate with slotted screwdriver.

7. Repeat steps 1 through 6 for other corner.

8. Set perimeter trim assembly aside for later installation.

Set Screws

Slot

Top Brass Trim

Mitered Edge

Side Brass Trim

Figure 14 - Assembling Brass Trim

Shoulder Screw

Mantel Base

Hole for 3" Wood Screw for Attaching Fireplace to Mantel

Gas Line Access Hole

Adjusting Plate

Shim

INSTALLING OPTIONAL BLOWER ACCESSORY GA3450TA

Removing Upper Louver

To install the blower accessory, you must ﬁrst remove the upper louver.

1. Lift screen off ﬁreplace and remove log set if installed.

2. Remove 4 screws from upper louver (see Figure 12, page 12). Save these screws.

Pull upper louver straight out from the cabinet. Be

3. careful not to scratch the paint. Set louver aside.

4. Open lower louver door by swinging door down (see Figure 12, page 12).

Assembled Brass Trim

Figure 13 - Attaching Brass Trim to

Hole for 3" Wood Screw for Attaching Fireplace to Wooden Base

Shoulder Screws

Fireplace

111244-01D 13

www.desatech.com

INSTALLATION

3 2 1

Red

Fan Switch�

(Auto/Off/On)

Blue

Thermostat�

Switch

�

(N.O.)

Green

White

Green

White

110/115 �

V.A.C.

Blower�

Motor

Black

Off

Auto

Continued

Installing Blower Accessory

CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and danger ous operation.

CAUTION: Verify proper operation after servicing.

Note: If you are using a mantel with your ﬁreplace, use the following instructions. If your ﬁreplace is built-in, see For Built-In Installation, page 15.

1. Install snap bushings found in blower kit into hole in left side of outer casing and into one of the holes in rear of remote/blower bracket.

Make sure the wire harness is ﬁrmly connected to the terminals on the blower bracket assembly.

3. Note the wire locations on back of AUTO/ OFF/ON switch. The terminals on back of switch are numbered 1, 2, and 3. Carefully remove red wire from terminal 3 and blue wire from terminal 1. Black wire can remain on middle terminal 2 (see Figure 15).

4. Carefully disconnect green and white wires at their insulated connectors (see Figure 16).

5. In top of the ﬁreplace cabinet, locate the four mounting holes on the outer casing. Align these four holes with those on the blower bracket assembly. Attach blower bracket assembly to the outer casing with 4 #10 screws provided (see Figure 15).

6. Route the wire harness through the hole in left side of bafﬂe and between ﬁrebox wrapper and outer casing.

Insert the 4 wire harnesses from behind the remote/blower bracket through hole in rear of bracket with bushing and through the left rectangular hole to front of fireplace (see Figure 15).

8. Reconnect red wire to switch position 3. Reconnect blue wire to switch position 1. Reconnect green and white wires.

Install the switch plate on the remote/blower bracket with 2 #10 screws provided (see Figure

17). Route power cord out of the cabinet by inserting it through the bushing on the outer casing (see Figure 15). Plug fan kit into 120Volt grounded power supply and test operation. Note: When switch is in the AUTO position, the fan will start after the ﬁreplace has run for a few moments. The fan will continue to run for several moments after the ﬁreplace has been turned off. When switch is in the ON position, the fan will run until turned to OFF.

10. Reinstall upper louver beginning with bottom screws (see Figure 12, page 12). Close lower louver door.

Blower Bracket Assembly

Wiring Routing Hole in Bafﬂe

Wire Harness

Screw

Switch

Power Cord

Switch Plate

Wire Harness

Figure 15 - Installing Blower Bracket

Assembly (Remote-Ready Unit Shown)

Remote/ Blower Bracket

Lower Louver Door

Blower Mounting Holes

Figure 16 - Wiring Diagram For Blower

Accessory Standard Installation

Switch Plate

Screw

Figure 17 - Installing Switch Plate to

www.desatech.com

Remote/ Blower Bracket

Remote/Blower Bracket

111244-01D

INSTALLATION

3 2 1

Red

Fan Switch

(Auto/Off/On)

Blue

Thermostat

Switch (N.O.)

Green

White

Green

White

110/115

V.A.C.

Blower

Motor

Black

Off

Auto

Continued

For Built-In Installation

WARNING: A licensed electrician must connect the wiring harness to electrical supply following all local codes. Electrician must provide a clamp on the box cover to secure the wiring. Wiring should be routed through the bushing in the hole on the outer casing of ﬁreplace.

1. Install snap bushing from blower kit into one hole on rear of remote/blower bracket (see Figure 18). The other hole is for a strain relief clamp (not supplied) to secure incoming electrical supply.

2. Follow steps 2 through 6 in Installing Blower Accessory, page 14.

3. A licensed electrician must follow the wiring diagram to connect incoming electrical supply to fan kit wiring harness (see Figure 19).

4. Plug power cord to outlet receptacle (not provided) as shown in Figure 18. Wind extra cable of power cord and tie up with plastic wire strap (see Figure 18). Set cable bundle between the remote/blower bracket and outer casing, away from the burner.

Blower Bracket Assembly

Wire Harness

Test to make sure blower is working properly.

6. Reinstall upper louver beginning with bottom screws (see Figure 12, page 12) and close lower louver.

Figure 19 - Wiring Diagram For Blower

Accessory Built-In Installation

Extension Cord

Use extension cord if needed. The cord must have a three-prong, grounding plug and a three-hole receptacle. Make sure cord is in good shape. It must be heavy enough to carry the current needed. An undersized cord will cause a drop in line voltage. This will result in loss of power and overheating. Use a No. 16 AWG cord for lengths less than 50 feet.

Screw

Switch

Power Cord

Clamp Connector (not included)

Outlet Receptacle (not included)

Remote/ Blower Bracket

Switch Plate

111244-01D 15

Plastic Wire Strap

Figure 18 - Installing Blower Bracket Assembly

Wire Harness

Lower Louver Door

www.desatech.com

+ 33 hidden pages