Denon VD-A11 Owners Manual
ENTER
1
7
0
2
8
+
10
3
9
456
TOP MENU DISPLAY
MARKERRANDOM
PAGE
A-B
ZOOM
DIMMER PIC.ADJ
REPEAT
SETUP
NTSC / PAL
CALL RETURN
SKIP SLOW / SEARCH
POWER
ANGLE SUBTITLE AUDIO
SEARCH MODE
PLAY
STILL /
PAUSE
STOP
PROG / DIR
CLEAR
OPEN /
CLOSE
ON OFF
T. MENU
DISP.
MENU
ENTER
1
7
0
2
8
+
10
3
9
456
TOP MENU DISPLAY
MARKERRANDOM
PAGE
A-B
ZOOM
DIMMER PIC.ADJ
REPEAT
SETUP
NTSC / PAL
CALL RETURN
SKIP SLOW / SEARCH
POWER
ANGLE SUBTITLE AUDIO
SEARCH MODE
PLAY
STILL /
PAUSE
STOP
PROG / DIR
CLEAR
SRS.TS
OPEN /
CLOSE
RC-962
ON OFF
T. MENU
DISP.
MENU
1 2
9
8
763
B
SUPER AUDIO CD DVI
OPEN / CLOSE
5
PLAY STOP
STILL / PAUSE
¢ON / STANDBY
£OFF
DVD AUDIO-VIDEO / SUPER AUDIO CD PLAYER DVD-A11
DENON LINK IEEE 1394
AL24 PLUS
REMOTE SENSOR
MODE SELECT
MODE SET UP
PUSH ENTER
DVD AUDIO-VIDEO/SUPER AUDIO CD PLAYER
DVD-A11
OPERATING INSTRUCTIONS
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
ISTRUZIONI PER L’USO
INSTRUCCIONES DE OPERACION
GEBRUIKSAANWIJZING
BRUKSANVISNING
FOR ENGLISH READERS PAGE 004 ~ PAGE 039
FÜR DEUTSCHE LESER SEITE 040 ~ SEITE 135
POUR LES LECTEURS FRANCAIS PAGE 042 ~ PAGE 136
PER IL LETTORE ITALIANO PAGINA 045 ~ PAGINA 137
PARA LECTORES DE ESPAÑOL PAGINA 139 ~ PAGINA 234
VOOR NEDERLANDSTALIGE LEZERS PAGINA 141 ~ PAGINA 235
FOR SVENSKA LÄSARE SIDA 144 ~ SIDA 236
2
ENGLISHDEUTSCHFRANCAISITALIANO
NOTE ON USE / HINWEISE ZUM GEBRAUCH /
OBSERVATIONS RELATIVES A L’UTILISATION / NOTE SULL’USO
• Avoid high temperatures.
Allow for sufficient heat dispersion when installed on
a rack.
• Vermeiden Sie hohe Temperaturen.
Beachten Sie, daß eine ausreichend Luftzirkulation
gewährleistet wird, wenn das Gerät auf ein Regal
gestellt wird.
• Eviter des températures élevées
Tenir compte d’une dispersion de chaleur suffisante
lors de l’installation sur une étagère.
• Evitate di esporre l’unità a temperature alte.
Assicuratevi che ci sia un’adeguata dispersione del
calore quando installate l’unità in un mobile per
componenti audio.
• Handle the power cord carefully.
Hold the plug when unplugging the cord.
• Gehen Sie vorsichtig mit dem Netzkabel um.
Halten Sie das Kabel am Stecker, wenn Sie den Stecker
herausziehen.
• Manipuler le cordon d’alimentation avec précaution.
Tenir la prise lors du débranchement du cordon.
• Manneggiate il filo di alimentazione con cura.
Agite per la spina quando scollegate il cavo dalla presa.
• Keep the set free from moisture, water, and dust.
• Halten Sie das Gerät von Feuchtigkeit, Wasser und
Staub fern.
• Protéger l’appareil contre l’humidité, l’eau et lapoussière.
• Tenete l’unità lontana dall’umidità, dall’acqua e dalla
polvere.
• Unplug the power cord when not using the set for long
periods of time.
• Wenn das Gerät eine längere Zeit nicht verwendet
werden soll, trennen Sie das Netzkabel vom
Netzstecker.
• Débrancher le cordon d’alimentation lorsque l’appareil
n’est pas utilisé pendant de longues périodes.
• Disinnestate il filo di alimentazione quando avete
l’intenzione di non usare il filo di alimentazione per un
lungo periodo di tempo.
• Do not obstruct the ventilation holes.
• Die Belüftungsöffnungen dürfen nicht verdeckt werden.
• Ne pas obstruer les trous d’aération.
• Non coprite i fori di ventilazione.
* (For sets with ventilation holes)
• Do not let foreign objects in the set.
• Keine fremden Gegenstände in das Gerät kommen
lassen.
• Ne pas laisser des objets étrangers dans l’appareil.
• E’ importante che nessun oggetto è inserito all’interno
dell’unità.
• Do not let insecticides, benzene, and thinner come in
contact with the set.
• Lassen Sie das Gerät nicht mit Insektiziden, Benzin oder
Verdünnungsmitteln in Berührung kommen.
• Ne pas mettre en contact des insecticides, du benzène
et un diluant avec l’appareil.
• Assicuratevvi che l’unità non venga in contatto con
insetticidi, benzolo o solventi.
•
Never disassemble or modify the set in any way.
•
Versuchen Sie niemals das Gerät auseinander zu
nehmen oder auf jegliche Art zu verändern.
•
Ne jamais démonter ou modifier l’appareil d’une manière
ou d’une autre.
•
Non smontate mai, nè modificate l’unità in nessun
modo.
• DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product, to
which this declaration relates, is in conformity with the following
standards:
EN60065, EN55013, EN55020, EN61000-3-2 and EN61000-3-3.
Following the provisions of 73/23/EEC, 89/336/EEC and
93/68/EEC Directive.
• ÜBEREINSTIMMUNGSERKLÄRUNG
Wir erklären unter unserer Verantwortung, daß dieses Produkt,
auf das sich diese Erklärung bezieht, den folgenden Standards
entspricht:
EN60065, EN55013, EN55020, EN61000-3-2 und EN61000-3-3.
Entspricht den Verordnungen der Direktive 73/23/EEC,
89/336/EEC und 93/68/EEC.
• DECLARATION DE CONFORMITE
Nous déclarons sous notre seule responsabilité que l’appareil,
auquel se réfère cette déclaration, est conforme aux standards
suivants:
EN60065, EN55013, EN55020, EN61000-3-2 et EN61000-3-3.
D’après les dispositions de la Directive 73/23/EEC, 89/336/EEC et
93/68/EEC.
• DICHIARAZIONE DI CONFORMITÀ
Dichiariamo con piena responsabilità che questo prodotto, al
quale la nostra dichiarazione si riferisce, è conforme alle seguenti
normative:
EN60065, EN55013, EN55020, EN61000-3-2 e EN61000-3-3.
In conformità con le condizioni delle direttive 73/23/EEC,
89/336/EEC e 93/68/EEC.
QUESTO PRODOTTO E’ CONFORME
AL D.M. 28/08/95 N. 548
ATTENZIONE: QUESTO APPARECCHIO E’ DOTATO DI DISPOSITIVO
OTTICO CON RAGGIO LASER.
L’USO IMPROPRIO DELL’APPARECCHIO PUO’ CAUSARE
PERICOLOSE ESPOSIZIONI A RADIAZIONI!
CLASS 1 LASER PRODUCT
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPPARAT
ADVARSEL: USYNLIG LASERSTRÅLING VED ÅBNING, NÅR
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION.
UNDGÅ UDSAETTELSE FOR STRÅLING.
VAROITUS! LAITTEEN KÄYTTÄMINEN MUULLA KUIN TÄSSÄ
KÄYTTÖOHJEESSA MAINITULLA TAVALLA SAATTAA
ALTISTAA KÄYTTÄJÄN TURVALLISUUSLUOKAN 1
YLITTÄVÄLLE NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE.
VARNING- OM APPARATEN ANVÄNDS PÅ ANNAT SÄTT ÄN I
DENNA
BRUKSANVISNING SPECIFICERATS, KAN ANVÄNDAREN
UTSÄTTAS FÖR OSYNLIG LASERSTRÅLNING SOM
ÖVERSKRIDER GRÄNSEN FÖR LASERKLASS 1.
,
CLASS 1
LASER
PRODUCT
,
,,
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
CAUTION:
• The ventilation should not be impeded by covering
the ventilation openings with items, such as
newspapers, table-cloths, curtains, etc.
• No naked flame sources, such as lighted candles,
should be placed on the apparatus.
• Please be care the environmental aspects of
battery disposal.
• The apparatus shall not be exposed to dripping or
splashing for use.
• No objects filled with liquids, such as vases, shall
be placed on the apparatus.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
3
FRONT PANEL
FRONTPLATTE
PANNEAU AVANT
PANNELLO FRONTALE
PANEL DELANTERO
VOORPANEEL
FRONT PANELEN
REAR PANEL
RÜCKWAND
PANNEAU ARRIERE
IL PANNELLO POSTERIORE
PANEL TRASERO
ACHTERPANEEL
BAKSIDAN
1 2
9
8
763
B
SUPER AUDIO CD DVI
OPEN / CLOSE
5
PLAY STOP
STILL / PAUSE
¢ON / STANDBY
£OFF
DVD AUDIO-VIDEO / SUPER AUDIO CD PLAYER DVD-A11
DENON LINK IEEE 1394
AL24 PLUS
REMOTE SENSOR
MODE SELECT
MODE SET UP
PUSH ENTER
q w
e
u
i
o
!0
r
t
y
!4
!3
!2
!5
!6
!7 @0
!8
!9
!1
@1 @2 @3 @4
@6@7@8
@9 #1
#0 #2 #3@5
#4
ENGLISH DEUTSCH FRANCAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA
#3 For only European model
#3 Nur für europäisches Modell
#3 Pour le modèle d’Europe seulement
#3 Solo per modelli europei
#3 Sólo para el modelo europeo
#3 Alleen voor Europees model
#3 Endast på Europa-modellen
ENGLISH
4
— TABLE OF CONTENTS —
z
Features...........................................................4, 5
x
Discs ....................................................................5
c
Cautions on Handling Discs .................................6
v
Connections...................................................6~11
b
Part Names and Functions...........................11, 12
n
Remote Control Unit..........................................13
m
Loading Discs.....................................................14
,
Changing the Default Settings.....................14~23
.
Playback.......................................................24~26
⁄0
Using the Mode Set Up ...............................26, 27
⁄1
Adjusting the Picture Quality.......................27~29
⁄2
Using the On-Screen Display.............................29
⁄3
Playing Repeatedly.............................................30
⁄4
Playing Tracks in the Desired Order...................31
⁄5
Playing Tracks in the Random Order..................31
⁄6
Playing Back WMA ............................................32
⁄7
MP3 Playback ..............................................32, 33
⁄8
Playing Still Picture Files (JPEG format).......33, 34
⁄9
Using the Multiple Audio,
Subtitle and Angle Functions .......................35, 36
¤0
Using the Menus .........................................36, 37
¤1
Marking Scenes you want to see again.............37
¤2
Playing in the Zoom Mode.................................38
¤3
Troubleshooting .................................................38
¤4
Main Specifications............................................39
• ACCESSORIES
Please check to make sure the following items are included with the main unit in the carton:
q Audio cord …………………………………………1
w Video cord …………………………………………1
e AC cord ……………………………………………1
r DENON LINK cord ………………………………1
t IEEE 1394 cord ……………………………………1
y Remote control unit (RC-962) ……………………1
u R6P/AA batteries …………………………………2
i Operating instructions ……………………………1
o Service station list…………………………………1
qwe r
1. Digital transfer connectors
The DVD-A11 can be connected to another digital
transfer compatible Denon component (AV
amplifier, etc.) using a single cable (included) for
high quality digital sound with little transfer loss.
(1) Denon Link terminal
This terminal can be used for digital transfer of
not only DVD video signals, but also multichannel audio signals of DVD audio.
(2) IEEE 1394 terminal
This terminal can be used for digital transfer of
not only DVD video signals, but also DVD
audio signals, Super Audio CD signals and
other multi-channel audio signals.
2. Super Audio CD multi-channel playback
compatibility
In addition to playing DVD audio and video discs,
the DVD-A11 can play multi-channel Super Audio
CDs with a playback frequency range covering
100 kHz and a dynamic range of 120 dB or greater
within the audible frequency range, and a
maximum of 5.1 channels can be output.
3. AL24 Processing Plus at all channel
AL24 Processing Plus compensates the input
digital data to reproduce the sound with analog
waveforms as close as possible to those existing
in nature and with 24-bit quality. The result is
increased musical reproduction capabilities of
reverberations, etc., at low levels, for a sound that
seems to draw you into the concert hall.
Equipped for not only the front left and right
channels but also for the surround left and right,
center and subwoofer channels.
4. High precision 24-bit D/A converter
The audio playback circuit includes an advanced
segment type D/A converter with the top
technical specifications in the business,
manufactured by Burr-Brown, a company with an
established reputation for D/A converters. This
high performance D/A converter allows not only
input of the 24-bit/192 kHz data of DVD-Audio
discs, it also includes an analog pure FIR filter for
ideal DSD playback of Super Audio CDs.
Furthermore, the same DAC is used unsparingly
for the surround, center and LFE channels to
provide optimum sound quality during multichannel playback as well.
1
FEATURES
IMPORTANT TO SAFETY
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION:
1. Handle the power supply cord carefully
Do not damage or deform the power supply cord.
If it is damaged or deformed, it may cause electric
shock or malfunction when used. When removing
from wall outlet, be sure to remove by holding the
plug attachment and not by pulling the cord.
2. Do not open the top cover
In order to prevent electric shock, do not open the
top cover.
If problems occur, contact your DENON DEALER.
3. Do not place anything inside
Do not place metal objects or spill liquid inside the
DVD audio-video/Super audio CD player.
Electric shock or malfunction may result.
Please, record and retain the Model name and serial
number of your set shown on the rating label.
Model No. DVD-A11 Serial No.
NOTE:
This DVD audio-video/Super audio CD player uses the
semiconductor laser. To allow you to enjoy music at a
stable operation, it is recommended to use this in a
room of 10°C (50°F) ~ 35°C (95°F).
Copyrights
2 It is prohibited by law to reproduce, broadcast, rent
or play discs in public without the consent of the
copyright holder.
For European For Oceanian
model model
5. HDCD®(High Definition Compatible Digital®)
decoder (NOTE 1)
HDCD is an encoding/decoding technology that
greatly reduces the distortion occurring at the
time of digital recording while maintaining
compatibility with the conventional CD format.
HDCD allows 24-bit data to be converted into the
16-bit data of current CDs with no loss in sound
quality.
The use of this HDCD decoder makes it possible
to achieve the high resolution and low distortion
characteristic of HDCD when playing HDCDcompatible discs, and DENON’s digital technology
optimizes the high sound quality possibilities of
HDCD technology. Furthermore, normal CDs and
HDCD-compatible CDs are automatically
identified, and the optimum digital signal
processing for that type of disc is used.
6. Dolby Digital (AC-3)/DTS decoder (NOTES 2, 3)
The DVD-A11 is equipped with a built-in Dolby
Digital (AC-3) /DTS decoder, allowing you to
recreate the atmosphere of a movie theater or
concert hall when using the DVD-A11 in
combination with an AV amplifier and speakers.
7. Progressive Scan circuit “DCDi
TM
” (NOTE 4)
The DVD-A11 is equipped with a high precision
Progressive Scan circuit “DCDi™” allowing it to
reproduce movies and other images on DVDs with
a quality near that of the original.
8. 12-bit/216 MHz video D/A converter (NOTE 5)
The DVD-A11 uses a video D/A converter that
conducts D/A conversion of all video signals at 12
bits and allows 8X oversampling in the
progressive mode to achieve the high quality
picture that DVDs are meant to provide. In
addition, NSV technology reduces noise upon D/A
conversion.
9. Thorough vibration-resistant design
(1) Mechanism using a hybrid loader.
(2) The pickup mechanism is positioned at the
center to reduce the effects of external
vibrations.
(3) A heavyweight chassis and low center of
gravity make for a low vibration design.
tyu
5
ENGLISH
2
DISCS
• The types of discs listed on the table below can be
used on the DVD-A11.
The marks are indicated on the disc labels or jackets.
Usable
discs
Mark (logo)
Recorded
signals
Disc
size
DVD video
DVD audio
(NOTE 1)
DVD-R
DVD-RW
(NOTE 2)
Digital audio +
digital video
(MPEG2)
12 cm
8 cm
12 cm
8 cm
12 cm
8 cm
Digital audio +
digital video
(MPEG1)
Digital audio
MP3
Digital picture
(JPEG)
Video CD
(NOTE 1)
CD
CD-R
CD-RW
(NOTE 3)
Recordable
ReWritable
12 cmJPEGPicture CD
R
R
R
W
R
W
2 The following types of discs cannot be played
on the DVD-A11:
• For European model:
DVDs with region numbers other than “2” or “ALL”
For Oceanian, South American model:
DVDs with region numbers other than “4” or “ALL”
• DVD-ROM/RAMs
• CD-ROMs (unless MP3, JPEG, WMA Files)
• CVD/VSDs
• CDVs (Only the audio part can be played.)
• CD-Gs (Only the audio is output.)
• Photo CDs
NOTE 1: Some DVD audio, DVD video and video CD
discs do not operate as described in this
manual due to the intentions of the discs’
producers.
NOTE 2: Playing DVD-R and DVD-RW discs
DVD-R and DVD-RW discs recorded in video
format on a DVD recorder can be played on
the DVD-A11.
Discs that have not be finalized cannot be
played.
Depending on the disc’s recording status,
the disc may not be accepted or may not be
played normally (the picture or sound may
be not be smooth, etc.).
NOTE 3: According to recording quality, some CD-R/
RW cannot be played.
2 Disc terminology
• Groups and tracks (DVD-audios)
DVD-audios are divided into several large sections
called “groups” and smaller sections called
“tracks”.
Numbers are allotted to these sections. These
numbers are called “group numbers” and “track
numbers”.
For example:
Group 1 Group 2
Track 1 Track 2 Track 3 Track 1 Track 2
• Titles and chapters (DVD-videos)
DVD-videos are divided into several large sections
called “titles” and smaller sections called “chapters”.
Numbers are allotted to these sections. These
numbers are called “title numbers” and “chapter
numbers”.
For example:
Title 1 Title 2
Chapter 1 Chapter 2 Chapter 3 Chapter 1 Chapter 2
• Tracks (Super audio CDs, video and music CDs)
Super audio CDs, video and music CDs are divided
into sections called “tracks”.
Numbers are allotted to these sections. These
numbers are called “track numbers”.
For example:
Track 1 Track 2
Track 3
Track 4 Track 5
• Playback control (video CDs)
Video CDs including the words “playback control”
on the disc or jacket are equipped with a function
for displaying menus on the TV screen for selecting
the desired position, displaying information, etc., in
dialog fashion.
In this manual, playing video CDs using such menus
is referred to “menu playback”.
Video CDs with playback control can be used on the
DVD-A11.
NOTE:
• This DVD player is designed and manufactured to
respond to the Region Management Information
that is recorded on a DVD disc.
If the Region number described on the DVD disc
does not correspond to the Region number of this
DVD player, this DVD player cannot play this disc.
2
4
For European model:
The Region number for this DVD
player is 2.
For Oceanian, South American
model:
The Region number for this DVD
player is 4.
12 cmDigital audio
Super audio
CD
12 cm
12 cm
JPEG
Digital audio
Fujicolor
CD
WMA
(Windows
Media
Audio)
10.Multiple functions
(1) Still picture playback function
Kodak Picture CD (NOTE 6) and Fujifilm
Fujicolor CD (NOTE 7) can be played on the
DVD-A11.
Still images stored in JPEG format on CDR/RWs can also be played.
(2) Windows Media™ playback function (NOTE 8)
Windows Media™ CDs can be played on the
DVD-A11.
(3) Multiple audio function
Selection of up to 8 audio languages.
(The number of languages offered differs from
DVD to DVD.)
(4) Multiple subtitle function
Selection of up to 32 subtitle languages.
(The number of languages offered differs from
DVD to DVD.)
(5) Multiple angle function
The angle of view can be changed.
(For DVDs on which multiple angles are
recorded.)
(6) GUI (Graphical User Interface) function
The DISPLAY button on the remote control
unit can be used to display player and disc
information on the TV screen.
(7) Marker function
The positions of up to five scenes can be
stored in the memory, so you can watch your
favorite scenes whenever you want.
(8) Playback disable function
This function can be used to disable playback
of DVDs you do not want children to watch.
NOTES:
1.
®
, HDCD®, High Definition Compatible
Digital®and Microsoft®are either registered
trademarks or trademarks of Microsoft
Corporation, Inc. in the United States and/or other
countries. HDCD system manufactured under
license from Microsoft Corporation, Inc. This
product is covered by one or more of the
following: In the USA: 5,479,168, 5,638,074,
5,640,161, 5,808,574, 5,838,274, 5,854,600,
5,864,311, 5,872,531, and in Australia: 669114.
Other patents pending.
2. Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories. Confidential
Unpublished Work. ©1992 – 1998 Dolby
Laboratories, Inc. All rights reserved.
3. “DTS” and ”DTS Digital Surround” are registered
trademarks of Digital Theater Systems, Inc.
4. “DCDi™” is trademark of Faroodja, a division of
Genesis Microchip Inc.
5. “NSV” is a trademark of Analog Devices, Inc.
6. “KODAK” is a trademark of Eastman Kodak
Company.
7. “FUJICOLOR CD” is a trademark of Fuji Photo
Film Co, Ltd.
8. “Windows Media™”, “Windows™”are a
trademarks of Microsoft Corporation, Inc.
ENGLISH
3
CAUTIONS ON HANDLING DISCS
Discs
Only the discs including the marks shown on page 5
can be played on the DVD-A11.
Note, however, that discs with special shapes (heartshaped discs, hexagonal discs, etc.) cannot be played
on the DVD-A11. Do not attempt to play such discs,
as they may damage the player.
Holding Discs
Avoid touching the surface of discs when loading and
unloading them.
Be careful not to get
fingerprints on the signal
surface (the side which
shines in rainbow colors).
Cleaning Discs
2 Fingerprints or dirt on the disc may lower sound and
picture quality or cause breaks in playback. Wipe off
fingerprints or dirt.
2 Use a commercially available disc cleaning set or a
soft cloth to wipe off fingerprints or dirt.
Wipe gently from the
middle outwards.
Do not wipe with a circular
motion.
NOTE:
• Do not use record spray or antistatic. Also do not
use volatile chemicals such as benzene or thinner.
Record
spray
Thinner
Benzene
Cautions on Handling Discs
• Do not get fingerprints, grease or dirt on discs.
• Be especially careful not to scratch discs when
removing them from their cases.
• Do not bend discs.
• Do not heat discs.
• Do not enlarge the center hole.
• Do not write on the labeled (printed) side with a ballpoint pen or a pencil.
• Water droplets may form on the surface if the disc is
moved suddenly from a cold place to a warm one. Do
not use a hairdryer, etc., to dry the disc.
Cautions on Storing Discs
• Always eject discs after playing them.
• Keep discs in their cases to protect them from dust,
scratches and warping.
• Do not put discs in the following places:
1. Places exposed to direct sunlight for long periods
of time
2. Humid or dusty places
3. Places exposed to heat from heaters, etc.
Cautions on Loading Discs
• Only load one disc at a time. Loading one disc on top
of another may result in damage or scratch the discs.
• Load 8 cm discs securely in the disc guide, without
using an adapter. If the disc is not properly loaded, it
may slip out of the guide and block the disc tray.
• Be careful not to let your fingers get caught when
the disc tray is closing.
• Do not place anything but discs in the disc tray.
• Do not load cracked or warped discs or discs that
have been fixed with adhesive, etc.
• Do not use discs on which the adhesive part of
cellophane tape or glue used to attach the label is
exposed, or discs with traces of tape or labels that
have been peeled off. Such discs may get stuck
inside the player, resulting in damage.
6
VIDEO INS-VIDEO IN
AUDIO IN
L
R
4
CONNECTIONS
• Read the manuals of all the components when
making connections.
• Keep the power supply cord unplugged until all
connections have been completed.
• If the power is on when connections are made,
noise may be generated and damage the speakers.
NOTES:
• Be sure to connect the left and right channels
properly, L (left) to L, R (right) to R.
• Plug the power supply cord securely into the power
outlet. Incomplete connection may result in noise.
• Binding the power supply cord together with
connection cords may result in humming or noise.
(1) Connecting to a TV
• Use the included audio video cord to connect the TV’s video input connector and audio input connectors to the
DVD-A11’s VIDEO OUT or S-VIDEO OUT and AUDIO OUT.
DVD-A11
S-Video output connector
The video signals are divided into color (C) and brightness (Y) signals, achieving a
clearer picture.
If the TV is equipped with an S-Video input connector, we recommend connecting it
to the DVD-A11’s S-Video output connector using a commercially available SVideo connection cord.
To power outlet
TV
• Connect the DVD-A11’s video outputs to the TV
either directly or through an AV amplifier. Do not
connect it via a VCR (video cassette recorder).
Some discs contain copy prohibit signals. If such
discs are played via a VCR, the copy prohibit
system may cause disturbance in the picture.
• Set the “TV TYPE” in “VIDEO SETUP” in “SETUP“
to comply with your TV's video format. When the
TV is PAL formated, set to PAL. (See page 18.)
NOTES:
• To use with 2-channel audio output, set “2
CHANNEL” in “AUDIO CHANNEL” in “AUDIO
SETUP” in “SETUP” at the initial settings. (See
page 19.)
• Set the “TV ASPECT” in “VIDEO SETUP” in
“SETUP” to comply with your TV’s aspect. (See
page 18.)
• To use with video out or s-video output, set
“INTERLACED” in “VIDEO OUT” in “VIDEO
SETUP” in “SETUP” at the initial settings. (See
page 18.)
CAUTIONS ON INSTALLATION
For heat dispersal, leave at least 10 cm of space
between the top, back and sides of this unit and
the wall or other components.
B
10 cm or more
wall
10 cm or more
ENGLISH
(2) Connecting to a TV or Monitor Equipped with Color Component Input
Connectors
COMPONENT VIDEO IN
PR/CRPB/CBY
AUDIO IN
LR
Color component output connectors (PR/CR, PB/CB and Y)
The red (P
R/CR), blue (PB/CB) and brightness (Y) signals are output independently, achieving
more faithful reproduction of the colors.
• The color component input connectors may be marked differently on some TVs or monitors
(P
R, PB and Y/R-Y, B-Y and Y/CR, CB and Y, etc.). For details, refer to the TV’s operating
instructions.
• Connect in this way if your TV is compatible with Progressive Scan.
DVD-A11
To power outlet
NOTES:
• Use the three commercially available video cords to connect the DVD-A11’s color component output
connectors to the TV or monitor.
• Set the “TV TYPE“ in “VIDEO SETUP“ in “SETUP“ to comply with your TV's video format. When the TV
is PAL formated, set to PAL. (See page 18.)
• Set the “VIDEO OUT” in “VIDEO SETUP” in “SETUP” to comply with Progressive TV.
• To use with 2-channel audio output, set “2 CHANNEL” in “AUDIO CHANNEL” in “AUDIO SETUP” in
“SETUP” at the initial settings. (See page 19.)
• Set the “TV ASPECT” in “VIDEO SETUP” in “SETUP” to comply with your TV’s aspect. (See page 18.)
TV
CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE
WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF
525 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE
CONNECTION TO THE “STANDARD DEFINITION” OUTPUT.
7
(3) Connecting to a TV with 21-pin SCART Terminal (For only European model)
• Use the commercially 21-pin SCART cable to connect the TV’s 21-pin SCART terminal to the DVD-A11’s 21pin SCART terminal (AV1 / AV2).
DVD-A11
To power outlet
TV
21-pin SCART terminal
• Set the “TV TYPE“ in “VIDEO SETUP“ in
“SETUP“ to comply with your TV's video format.
When the TV is PAL formated, set to PAL. (See
page 18.)
NOTES:
•
Some discs contain copy prohibit signals. If such
discs are played via a VCR, the copy prohibit
system may cause disturbance in the picture.
• To improve picture quality, you can change the video signal output from the AV1 terminal from “Video“ to
either “S-Video“ or “RGB“ to suit the type of television you are using (See page 18).
• You can also connect other equipment to AV2.
AV1
AV2
AV1
AV2
VCR
SCART terminal
of TV set
This unit Video cassette recorder
Satellite receiver
or decoder
NOTES:
•
Set the DVD-A11 to the standby mode to output video or audio signals of another device connected to the
DVD-A11’s 21-pin SCART terminal.
(If the power is on, the DVD-
A11
’s video and audio signals are output. If the power is off, the signals of
the other device will not be output.)
• To use the 21-pin SCART terminal, set “AUDIO CHANNEL” under “AUDIO SETUP” at “SETUP” to “2
CHANNEL”.
ENGLISH
2
Connecting an optical fiber cable (commercially available) to the digital audio input connector (OPTICAL)
Dust cap Line up in proper direction
Remove the dust cap, line up the cable in the proper
directly, then insert it securely as far as it goes.
NOTE:
• Store the dust cap in a safe place, and be careful
not to lose it.
When not using the terminal, attach the cap to
protect the terminal from dust.
NOTES:
• Harsh noise that could harm your ears or damage the speakers is generated when a DVD recorded in DTS
is played while using a decoder, etc., that is not DTS-compatible.
• When playing copyright-protected linear PCM or packed PCM DVDs, in consideration of copyrights, no digital
signals are output for sources exceeding 48 kHz/16 bits. When playing such sources, either set “LPCM
(44.1 kHz/48 kHz)” under “AUDIO SETUP” at “SETUP” to “ON” (see page 20) or make analog connections.
(See page 9.)
• When making digital connections to an AV amplifier that is not compatible with 96 kHz/88.2 kHz signals, set
“LPCM (44.1 kHz/48 kHz)” under “AUDIO SETUP” at “SETUP” to “ON”. (See page 20.)
• With Super audio CDs, digital audio signals cannot be output. Use analog connections. (See page 9.)
8
2 Sound output from the DVD-A11’s digital audio output connectors
In the case of bit stream output
NORMALAudio recording format
Dolby Digital
DTS
MPEG Audio
DIGITAL OUT
2 channels PCM
(48 kHz / 16 bit)
2 channels PCM
(48 kHz / 16 bit)
2 channels PCM
(48 kHz / 16 bit)
PCM
DVD video
Dolby Digital bitstream
DTS bitstream
2 channels PCM
(48 kHz / 16 bit)
Settings
In the case of PCM output
OFF
DVD
audio
Audio recording format
Linear
PCM
Video CD
Music CD
MP3 CD
WMA CD
44.1 kHz / 16 bit PCM
44.1 kHz / 16 bit PCM
192 kHz / 16 ~ 24 bit
176.4 kHz / 16 ~ 24 bit
MPEG 1
44.1 kHz / 16 bit Linear PCM
MP3 (MPEG-1 Audio Layer 3)
WMA (Windows Media Audio)
96 kHz / 16 ~ 24 bit
88.2 kHz / 16 ~ 24 bit
48 kHz / 16 ~ 24 bit
44.1 kHz / 16 ~ 24 bit
96 kHz / 16 ~ 24 bit
48 kHz / 16 ~ 24 bit
LPCM SELECT
48 kHz / 16 bit PCM
44.1 kHz / 16 bit PCM
48 kHz / 16 bit PCM
44.1 kHz / 16 bit PCM
48 kHz / 16 bit PCM
44.1 kHz / 16 bit PCM
48 kHz / 16 bit PCM
48 kHz / 16 bit PCM
ON
DVD
video
44.1 kHz / 16 bit PCM
44.1 kHz / 16 bit PCM
No output data
No output data
No output data
No output data
No output data (*1)
No output data (*2)
No output data
No output data (*1)
44.1, 48 kHz / 16 bit PCM
44.1, 48 kHz / 16 bit PCM
Copy protection ON
88.2 kHz / 16 ~ 24 bit PCM
96 kHz / 16 ~ 24 bit PCM
88.2 kHz / 16 ~ 24 bit PCM
48 kHz / 16 ~ 24 bit PCM
96 kHz / 16 ~ 24 bit PCM
Copy protection OFF
44.1, 48 kHz / 16 bit PCM
44.1, 48 kHz / 16 bit PCM
48 kHz / 16 ~ 24 bit PCM
44.1 kHz / 16 ~ 24 bit PCM
96 kHz / 16 ~ 24 bit PCM
Linear PCM or
Packed PCM
Settings
*1 Only 48 kHz/16 bit sources are output.
*2 Only 44.1 kHz/16 bit sources are output.
*3 44.1 kHz/16-bit PCM signals are output during CD layer playback.
• Down-mixed to 2 channels for multi-channel PCM sources. (Only the front left and right channels are output for
sources for which down-mixing is prohibited.)
• When “OFF” is selected, digital signals are not output from the digital audio output at this time.
• Bitstream signals are signals that are compressed and converted into digital format. They are decoded into
multi-channel audio signals (5.1-channels, etc.) by the decoder.
• Linear PCM audio is a signal recording format used for music CDs.
While signals are recorded at 44.1 kHz/16 bit for music CDs, for DVDs they are recorded at 44.1 kHz/16 bit to
192 kHz/24 bit, providing higher sound quality than music CDs.
• Packed PCM signals are high sound quality compressed PCM signals that are decompressed with virtually no
loss of data.
Super
audio CD
No output data (*3)DSD (DIRECT STREAM DIGITAL)
No output data (*3)
(4) Connecting to a AV amplifier with a Built-in decoder
When DVDs recorded in Dolby Digital or DTS are played, Dolby Digital or DTS bitstream signals are output from
the DVD player’s digital audio output connectors. If a Dolby Digital or DTS decoder is connected, you can achieve
sound with the power and sense of presence of a movie theater or concert hall.
PHONES
DIRECT STEREO
ANALOG EXT. IN
DOLBY
SURROUND
DTS
SURROUND
WIDE
SCREEN
CINEMA /
MUSIC
6.1 / 7.1
SURROUND
VIDEO
ON / OFF
STATUS
M-ZONE 1
FUNCTION CONTROL
INPUT
MODE
5CH / 7CH
STEREO
DSP
SIMULATION
TONE
DEFEAT
MODE
SELECT
REC /
M-ZONE 2
SURROUND MODE
INPUT REC SELECT / M-ZONE
MULTI FUNCTION
DVD-A11
Digital audio input
connector
(OPTICAL)
Optical fiber cable
(commercially
available)
75 Ω/ohms
pin-plug cable
(commercially
available)
Front speaker (left)
Center speaker
Front speaker (right)
Digital audio
input connector
(COAXIAL)
Subwoofer
Surround speaker (left)
AV amplifier with a built-in decoder
(AV control center)
Surround speaker (right)
To power outlet
(or)
9
ENGLISH
(6) Connecting to a Digital Recorder (MD Recorder, DAT Deck, etc.)
89
B
✽ Set the “AUDIO SETUP” default setting as shown below. (See page 20.)
•“DIGITAL OUT” → “PCM”
“LPCM (44.1 kHz / 48 kHz)” → “ON”
Playing DVDs with incorrect settings may result noise that could damage your ears or the speakers.
DVD-A11
75 Ω/ohms pin-plug cable (commercially available)
Optical fiber cable (commercially available)
Digital audio
input
connector
(COAXIAL)
Digital audio input
connector (OPTICAL)
(7) Connecting to a Stereo Component
DVD-A11
Stereo component
NOTE:
• When connecting to a 2-channel audio stereo device, set “AUDIO CHANNEL” under “AUDIO SETUP” at
“SETUP” to “2 CHANNEL” (see page 19). For multi-channel sources, the signals are down-mixed into two
channels (analog).
(Only the front left and right channels are output for sources for which down-mixing is prohibited.)
(5) Connecting a basic 5.1-channel surround system
Analog 5.1-channel audio signals can be output from the DVD-A11.
The multichannel audio signals recorded in packed PCM and the multichannel Super audio CDs can be played
when an AV amplifier equipped with analog 5.1-channel audio inputs is connected.
PHONES
DIRECT STEREO
ANALOG EXT. IN
DOLBY
SURROUND
DTS
SURROUND
WIDE
SCREEN
CINEMA /
MUSIC
6.1 / 7.1
SURROUND
VIDEO
ON / OFF
STATUS
M-ZONE 1
FUNCTION CONTROL
INPUT
MODE
5CH / 7CH
STEREO
DSP
SIMULATION
TONE
DEFEAT
MODE
SELECT
REC /
M-ZONE 2
SURROUND MODE
INPUT REC SELECT / M-ZONE
MULTI FUNCTION
DVD-A11
To power outlet
Front speaker (left)
Center speaker
Front speaker (right)
Subwoofer
Surround speaker (right)
AV amplifier with 5.1-channel
input terminals
Surround speaker (left)
FRONT
SUBWOOFER
SURROUND
CENTER
NOTES:
• For multi-channel connections, set “AUDIO CHANNEL” under “AUDIO SETUP” at “SETUP” to “MULTI
CHANNEL” and make the “SPEAKER CONFIGURATION”, “CHANNEL LEVEL” and “DELAY TIME” settings.
(See pages 19, 20.)
• With the DVD-A11, we recommend turning the digital output off and only outputting analog signals in order
to keep interference from the digital output circuitry to the minimum and allow you to enjoy high bit, high
sampling frequency, high quality multi-channel sound.
NOTE:
• Digital audio signals cannot be output when playing Super Audio CDs. Use analog connections to record
Super Audio CDs.
(or)
10
ENGLISH
(8) Denon Link connections
High quality digital sound with reduced digital signal transfer loss can be enjoyed by connecting a separately
sold Denon Link compatible AV amplifier.
PHONES
DIRECT STEREO
ANALOG EXT. IN
DOLBY
SURROUND
DTS
SURROUND
WIDE
SCREEN
CINEMA /
MUSIC
6.1 / 7.1
SURROUND
VIDEO
ON / OFF
STATUS
M-ZONE 1
FUNCTION CONTROL
INPUT
MODE
5CH / 7CH
STEREO
DSP
SIMULATION
TONE
DEFEAT
MODE
SELECT
REC /
M-ZONE 2
SURROUND MODE
INPUT REC SELECT / M-ZONE
MULTI FUNCTION
DVD-A11
To power outlet
Front speaker (left)
Center speaker
Front speaker (right)
Subwoofer
Surround speaker (right)
AV amplifier with Denon Link input
terminals
Surround speaker (left)
DENON LINK
2 DENON LINK Second Edition:
• With the DENON LINK, Second Edition (2nd), the audio signals are transferred from the DVD player to the
AV amplifier in digital form, with the same quality as the signals recorded on the disc.
Digital transfer of the high quality multi-channel signals of DVD audio is possible for all discs. (A Second
Edition compatible DVD player and AV amplifier are required for this.)
2 Compatibility with previous models:
• With Second Edition, the format of the signals handled differs from that of the previous version of
DENON LINK.
Thus, digital audio signals output from a DENON LINK S.E. compatible DVD player can only be played
on a DENON LINK S.E. compatible AV amplifier (Playback with DENON LINK connections is not
possible when using a DENON LINK S.E. compatible DVD player in combination with an AV amplifier
that is not S.E. compatible.).
• If the DENON LINK connector on your AV amplifier is not S.E. compatible, please consult your authorized
DENON dealer.
•“S.E.” is indicated on the rear panel’s DENON LINK connector on DENON LINK S.E. compatible products.
2 DENON LINK S.E. settings:
• At “AUDIO SETUP” under “Default Settings”, set “DENON LINK” to “2nd”. (See pages 19 to 21.)
• If you connect the DENON LINK, set to “2nd”.
NOTES:
• When DENON LINK is set, the down-mixed audio signals are output from the only left and right terminals.
To use the analog terminals, cancel the DENON LINK setting (set to “OFF”).
•“AUDIO CHANNEL”, “DIGITAL OUTPUT”, “LPCM (44.1kHz/48kHz)”, “IEEE1394”, “SOURCE DIRECT”
and “BASS ENHANCER” cannot be set at “AUDIO SETUP” under “Default Settings” when using the
DENON LINK connector.
The “PURE DIRECT” “DIGITAL OFF” and “ALL OFF” settings cannot be made either. (See pages 26,
27.)
• The DVD-A11’s speaker settings are invalidated when the DENON LINK connector is connected.
• When the DENON LINK 2nd connection, Super Audio CD’s signals are not output from the DENON LINK
connector. Please use the analog audio output terminals.
(9) IEEE 1394 connections
The simple connection of one IEEE 1394 cable permits high quality digital transfer of the following between
devices having IEEE 1394 connectors: the audio of DVD video, DVD audio that up until now could only be
connected by 5-conductor audio cable in an analog connection, or Super Audio CD and other multi-channel
audio. (unless DENON LINK connections)
(IEEE 1394 is an international standard established by the Institute of Electrical and Electronics Engineers, Inc.
of the U.S.)
PHONES
DIRECT STEREO
ANALOG EXT. IN
DOLBY
SURROUND
DTS
SURROUND
WIDE
SCREEN
CINEMA /
MUSIC
6.1 / 7.1
SURROUND
VIDEO
ON / OFF
STATUS
M-ZONE 1
FUNCTION CONTROL
INPUT
MODE
5CH / 7CH
STEREO
DSP
SIMULATION
TONE
DEFEAT
MODE
SELECT
REC /
M-ZONE 2
SURROUND MODE
INPUT REC SELECT / M-ZONE
MULTI FUNCTION
DVD-A11
To power outlet
Front speaker (left)
Center speaker
Front speaker (right)
Subwoofer
Surround speaker (right)
AV amplifier with IEEE 1394 terminals
Surround speaker (left)
IEEE 1394
11
ENGLISH
NOTES:
• Please use the included IEEE 1394 cable. When using a cable other than the included IEEE 1394 cable,
please use a 4-pin IEEE 1394 cable with a length of 3.5 m or less for S400 or higher.
• The “IEEE 1394 audio signal (A&M protocol)” output from the DVD-A11’s IEEE 1394 connector not out
video signals, please connecting to a TV or Monitor with “component video output” or “S-video output”
or “Video output”. (See pages 6, 7).
• The “IEEE 1394 audio signal (A&M protocol)” output from the DVD-A11’s IEEE 1394 connector can only
be received on AV equipment equipped with an IEEE 1394 connector. Digital video (DV), personal
computer, and i-Link (a Sony trademark) audio signals cannot be sent and received. Incorrect connections
could lead to malfunction. Connect as instructed in the other device’s operating manual. Note that there is
no guarantee of the operation of the connection even between devices supporting IEEE 1394. Whether or
not data and control signals can be transmitted and received between devices supporting IEEE 1394
depends on the functions of the respective devices.
• When connecting using the IEEE 1394 connector, only connect one cord between the two devices. Never
connect two cords between the two devices (loop connection). If this is done, the signal output from one
device will return to the same device, resulting in malfunction.
• No audio signals are output from the DVD-A11’s analog connectors when IEEE 1394 is set.
To use the analog connectors, set the IEEE 1394 setting to “Cancel (Off)”.
• When using the IEEE 1394 mode, the “AUDIO CHANNEL”, “DIGITAL OUTPUT”, “LPCM (44.1 kHz/48
kHz)”, “SOURCE DIRECT” and “BASS ENHANCER” settings under “SETUP” – “AUDIO SETUP” cannot
be made.
The “PURE DIRECT” “DIGITAL OFF” and “ALL OFF” settings cannot be made either. (See pages 26,
27.)
• When the IEEE 1394 connector is connected, the DVD-A11’s speaker settings are disabled.
• During playback of a device supporting IEEE 1394, please do not disconnect the IEEE 1394 cable of the
other device, do not connect a new device, and do not switch the power on or off. Doing so may interrupt
the audio.
• Among the devices that support IEEE 1394, when the power is in the standby mode or off, some devices
are not able to relay data. Please see the operation manual of the connected device that supports IEEE
1394. This unit is not able to relay the IEEE 1394 data while in the standby mode.
• Devices that support IEEE 1394 have the maximum data transfer speed supported by that device marked
in the vicinity of the IEEE 1394 connector. The maximum transfer speed of IEEE 1394 is defined as
approximately 100/200/400 Mbps*, with 200 Mbps items having S200 inscribed and 400 Mbps items
having S400 inscribed. The maximum IEEE 1394 data transfer speed of this unit is 400 Mbps. The actual
transfer speed may be slower than 400 Mbps when S100 or S200 devices are connected, or depending
on the specifications of the device. Try to ensure that connections are made between devices that have
the same maximum data transfer speed.
* Mbps (Mega bps) is an abbreviation of “Mega bits per second” and indicates the volume of data that can
be communicated in 1 second. At 400 Mbps, 400 Mega bits of data is transferred in 1 second.
✽ The DVD-A11’s IEEE 1394 mode is designed based on IEEE Std. 1394a-2000, Standard for a High
Performance Serial Bus.
✽ IEEE 1394 network
The following types of connections can be made between devices handling IEEE 1394 audio signals (A&M
protocol):
q Daisy chain connections
Connect the sets in series using a single IEEE 1394 cord. Up to 15 sets can be connected.
w Tree (tower) connections
Connect the sets in parallel and in series using a single IEEE 1394 cord. Up to 63 sets can be connected.
Copyright Protection System
To play back through an IEEE 1394 connection the audio of Super Audio CD or DVD (except for discs that may
be copied freely), both the player and the amplifier are required to support a copyright protection system called
DTCP (Digital Transmission Content Protection). DTCP is copy protection technology comprising data encryption
and the authentication of the remote device. This unit supports DTCP. Please see the operation manual of your
amplifier for information about your amplifier.
5
PART NAMES AND FUNCTIONS
(1) Front Panel
See page 3.
q
Power button
• Press once to turn the power on.
• Press again to set to the “OFF” position and
turn the power off.
• Set the power to the standby mode by pressing
the POWER OFF button on the remote control
unit while the power is on.
• Turn the power on from the standby mode by
pressing the POWER ON button on the remote
control unit.
w
Power indicator
• This indicator lights when the power is on and
when the power is in the standby mode.
e
AL24 PLUS indicator
• This indicator lights when the audio signals of
a DVD, etc., are being processed digitally with
the AL24 processing Plus.
r
DENON LINK indicator
• This indicator lights when the audio signals are
transferred by DENON LINK connections.
t
IEEE 1394 indicator
• This indicator lights when the audio signals
are transferred by IEEE 1394 connections.
(See page 21.)
y
Disc tray
• Load discs here. (See page 14.)
• Press the OPEN/CLOSE button
!6 to open and
close the disc tray.
• The disc tray is also closed when the PLAY
button
u is pressed.
u
PLAY button (1)
• Press this button to play the disc. (See page 24.)
i
STOP button (2)
• Press this to stop the disc. (See page 25.)
o
Skip button (8)
• Press this to move back to the beginning of the
current track (or chapter).
• Press again to move back to the beginning of
the previous track (or chapter). (See page 25.)
!0
Skip button (9)
• Press this to move ahead to the beginning of
the next track (or chapter). (See page 25.)
!1
Remote control sensor
!2
SUPER AUDIO CD indicator
• This indicator lights when playing areas of
Super audio CDs recorded in DSD format
(STEREO/MULTI).
!3
DVI indicator
• This indicator lights when the video signals
output from the DVI-D output connector.
!4
Display
• Information on the disc that is currently playing
is shown on the display. (See page 12.)
!5
STILL/PAUSE button (3)
• Press this button to pause images or music or
to play images frame by frame. (See page 25.)
!6
OPEN/CLOSE button (5)
• Press this button to open and close the disc
tray.(See page 14.)
!7
MODE of MODE SETUP button
• Press this to set the MODE SETUP (@0).
(Super Audio CD / FILTER / PURE DIRECT
/ DVI SETUP / DVI BK LEVEL)
!8
Slow/Search button (6)
• Press this to set the slow play mode and to
search in the reverse direction. (See page 25.)
!9
Slow/Search button (7)
• Press this to set the slow play mode and to
search in the forward direction. (See page 25.)
@0
SELECT of MODE SETUP selector
• Use this to switch the area/layer of the Super
audio CDs played with priority, and turn the
circuitry other than the analog audio signal
circuitry on and off and to set the video signal
output from the DVI connector, etc.
• SUPER AUDIO CD SETUP
Use this to set the area/layer of the Super
audio CDs played with priority.
MULTI:
When playing Super audio CDs, the Multichannel area is played with priority.
STEREO:
When playing Super audio CDs, the stereo
area area is played with priority.
CD:
When playing Super audio CDs, the CDs layer
area is played with priority.
• FILTER:
This sets the low pass filter value when
playing Super Audio CDs.
50 kHz:
High frequencies of 50 kHz and higher are cut.
100 kHz:
High frequencies of 100 kHz and higher are
cut.
Set to 100 kHz when a high frequency
compatible AV amplifier, etc., is connected.
Lights when the audio signals can be down-mixed.
12
ENGLISH
• PURE DIRECT (AUDIO) MODE:
The circuits not being used (output signals)
can be turned off.
NORMAL:
This turns the PURE DIRECT mode off. All
signals are output.
VIDEO OFF:
This turns the video output off. Use this when
only using audio signals.
DIGITAL OFF:
This turns the digital output off.
ALL OFF:
This turns the digital output, display and video
output off.
• DVI (VIDEO output) SETUP MODE:
Use this to set the DVI connector’s video
signal output.
DVI OFF:
No signal from the DVI-D connector.
480P:
480P video signals are output from the DVI-D
connector.
720P:
720P video signals are output from the DVI-D
connector.
1080i:
1080i video signals are output from the DVI-D
connector.
✽ When the DVI-D connector output the
signals, no programme signals from the
component video connector.
• DVI BK (Black) LEVEL:
This switches the digital RGB video level (data
range) of the DVI-D terminal.
NORMAL:
Video level (data range): 16 (black) to 235
(white)
ENHANCED:
Video level (data range): 0 (black) to 246
(white)
✽ When the DVI-D terminal is connected,
the black may seem to stand out,
depending on the TV or Monitor you are
using. In this case, set this to
“ENHANCED”.
(2) Rear Panel
@1
DVI-D-Video output connector
(DVI-D OUT)
• Connect using DVI-D connection cord
(available in stores).
@2
Component video output connectors
(COMPONENT VIDEO OUT)
• Connect using video cords (available in
stores).
@3
S-Video output connector
(S-VIDEO OUT)
• Connect using an S-Video connection cord
(available in stores).
@4
Video output connector (VIDEO OUT)
• Connect using the included video cord.
@5
Digital output connector (IEEE 1394)
• This is for connection of a separately sold AV
amplifier equipped with a IEEE 1394
connector.
• Use it to achieve high quality digital sound
with low data loss.
@6
Digital output connector
(DENON LINK)
• This is for connection of a separately sold AV
amplifier equipped with a Denon Link
connector.
• Use it to achieve high quality digital sound
with low data loss.
@7
Digital audio output connector
(OPTICAL)
• Connect using an optical fiber cable (available
in stores).
• Digital data is output from this connector.
@8
Digital audio output connector
(COAXIAL)
• Connect using an digital audio cord. Connect a
commercially available 75 Ω/ohms pin-plug
cord.
• Digital data is output from this connector.
@9
Control connector (RS-232C)
• This is a terminal for future system expansion.
#0
Control input connector
(ROOM TO ROOM/IN)
• This is the input connector for wired remote
control.
Consult your DENON dealer if you wish to use
this connector.
#1
Control output connector
(ROOM TO ROOM/OUT)
• This is the output connector for wired remote
control.
Consult your DENON dealer if you wish to use
this connector.
#2
Audio output connectors
(AUDIO OUT)
• Connect using the included audio cord.
#3
21-pin SCART terminal (AV1/AV2)
(For only European model)
• Connect using a 21-pin SCART cable (available
in stores).
#4
Power input (AC IN)
• Connect to AC power supply using the
included power supply cord.
(3) Display
Lights during playback of multiple angles disc.
Lights to indicate the currently playing disc.
These light to indicate the names of the sections of the disc
being played.
Lights to indicate the currently playing audio format.
Lights to indicate the currently playing
audio channel.
L: Front left channel
C: Center channel
R: Front right channel
SL: Surround left channel
S: Mono surround channel
SR: Surround right channel
LFE: Low frequency effect
Lights to indicate the
currently playing video
type.
F: Film source
V: Video source
Lights during playback, flashes when the resume play memory function is activated.
Lights in the programmed play mode.
Lights in the still/pause mode.
Displays the title, track number
and elapsed time during
playback.
These light to indicate
the time display mode.
Lights when progressive video
signals are being output.
Lights in the repeat play mode.
Lights in the random play mode.
Loading...