Deni 3400 User Manual

Meat Grinder

550 Watts

					S
			U
	N
O						s
B
				e
			d
	lu
c						s
In
					e
			ip
		c
	e
R

Model #3400

IMPORTANT

Please keep these instructions and yourModeloriginal3200box packaging.

INSTRUCTIONS

FOR PROPER USE AND CARE

IMPORTANT SAFEGUARDS

When using this electrical appliance, safety precautions

■Read all of the instructions.

■To protect against risk of electrical shock do not put meat grinder in water, other liquid, or where water may flood the area.

■Place the meat grinder securely in the center of the counter or work space on a flat surface.

■Close adult supervision must be provided when this appliance is used by or near children. This appliance is not recommended for children.

■Unplug from outlet when not in use, before putting on or taking off parts, and before cleaning.

■Avoid contact with moving parts. Never feed food by hand. Always use food pusher. Keep hair, hands, clothing, and utensils away from moving plates while operating to reduce the risk of personal injury and/or damage to the meat grinder.

■Do not use fingers to scrape away food from discharge disc while appliance is operating. Injury may result.

CAUTION: DO NOT PUT YOUR FINGERS NEAR THE HOPPER OR HEAD WHILE IN OPERATION.

■Do not operate with a damaged cord, plug, after the appliance malfunctions, or if it is dropped or damaged in any manner. Return the meat grinder to Keystone Manufacturing Co., Inc. for examination, repair or electrical or mechanical adjustment.

■Using attachments not recommended or sold by Keystone Manufacturing Co., Inc. may cause hazards.should always be observed, including the following:

■Do not use outdoors, household use only.

■Do not let cord hang over edge of table or counter. Do not let cord come in contact with hot surfaces, including the stove.

■WARNING: The cutting blade is sharp. Handle with care when both using and cleaning.

■Do not place near hot gas, electric burner, in an oven, or in a dishwasher.

■Never leave meat grinder unattended while it is operating.

■If motor stalls, turn off immediately and unplug power unit. To avoid injury, first detach meat grinder head then disassemble and remove clogged pieces.

■Do not use an extension cord with this meat grinder. However, if one is used, it must have a rating equal to or exceeding the rating of this appliance.

■The meat grinder should always be in the off position before inserting or removing plug from a wall outlet.

■Do not pull on the power cord to disconnect, pull on the head of the plug.

■This meat grinder should not be used for other than the intended use.

■The Deni Meat Grinder has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way, as a safety feature. Reverse the plug if the plug does not fit fully in the outlet. Contact a qualified electrician if it still does not fit. Do not attempt to defeat this safety feature.

SAVE THESE INSTRUCTIONS 1

Meat Grinder

Features

Food Pusher

Hopper Tray

Grinder Head

Locking Knob

Sausage Stuffer

Grinding Plates

• Coarse

Operating Buttons

• Medium

• On

• Fine

• Off

• Reverse

Cap

Stainless Steel

Feed Screw

Motor Housing

Cutting Blade

2

Functions

Operating	Allows you to turn the unit ON, OFF and REVERSE the
Buttons:	direction of the feed screw if the unit jams.
Locking Knob:	Holds the grinder head tightly in place.
Motor Housing: Provides an outer shell for the motor mechanism.
Food Pusher:	Used to feed foods into the hopper opening.
Hopper Tray:	Holds food to be ground.
Grinder Head:	Holds feed screw, cutting blade, and cutting plates for
	grinding.
Feed Screw:	Rotates cutting blade to grind meat.
Cutting Blade:	Cuts the food before going through the grinding plates.
Cutting Plates:	Grinds meat into the desired texture; fine, medium, or coarse.
Sausage	Works as a funnel to fill sausage casings.
Stuffer:
Cap:	Holds the cutting blade and cutting plates in place during
	grinding.

3

Meat Grinder

Assembling

1.Make sure the unit is unplugged while assembling.

2.Insert the feed screw into the grinder tube, long end first. (Figure 1)

3.Position the cutting blade onto the feed screw with the flat surface of the blade

facing you. NOTE: If it is not

fitted properly, meat will not be ground and the cutting plate may be

damaged. (Figure 2)

4.Position the desired cutting plate onto the feed screw, against the flat sides of the cutting blade. Be sure the notches on the cutting plate fit into the slots in the grinder tube. (Figure 3)

5.Securely attach the cap to the end of the

grinder tube. (Figure 4)

6.Insert the grinder head into the opening of the motor housing. Turn slowly and push in, until it is firmly seated.

Note: You may need to loosen the locking knob to allow the grinder head to be fully inserted. (Figure 5)

7.Secure the grinder head by turning the

4	locking knob until tight. (Figure 6)

8.Place the hopper tray on the feed tube. (Figure 7)

9.Use the food pusher to push food gently, one piece at a time into the feeding tube. Do not force the food into the tube.

How To Assemble Sausage Maker

1.Insert feed screw into grinder tube.

2.Place the coarse grinding plate onto the feed screw.

3.Place wide end of sausage stuffer against the grinding plate. Hold in place while attaching the screw ring.

4.Insert grinder tube into the motor unit and tighten the locking knob to secure.

How To Operate

1.Before using for the first time, remove all packaging and wash parts. DO NOT place in dishwasher.

2.Place the unit on a sturdy work surface so the air-vents at the bottom and back are not blocked.

3.Make sure the unit is OFF. Plug the unit in.

4.Place a bowl or plate beneath the grinding tube to catch the ground meat.

5.Turn the grinder on. The ground meat will come out through the grinding plate in the head. Note: The grinder must be on BEFORE adding food.