INSTRUCTION MANUAL
6" Variable Speed
Bench Jointer
(Model 37-070)
PART NO. 901609 (013)
Copyright © 2001 Delta Machinery
ESPAÑOL: PÁGINA 21
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call
1-800-223-7278 (In Canada call 1-800-463-3582).
2
SAFETY RULES
Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there
are certain hazards involved with the operation of the product. Using the machine with respect and caution will
considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored,
personal injury to the operator may result. Safety equipment such as guards, push sticks, hold-downs, featherboards,
goggles, dust masks and hearing protection can reduce your potential for injury. But even the best guard won’t make
up for poor judgment, carelessness or inattention. Always use common sense and exercise caution in the workshop.
If a procedure feels dangerous, don’t try it. Figure out an alternative procedure that feels safer. REMEMBER: Your
personal safety is your responsibility.
This machine was designed for certain applications only. Delta Machinery strongly recommends that this machine not
be modified and/or used for any application other than that for which it was designed. If you have any questions relative
to a particular application, DO NOT use the machine until you have first contacted Delta to determine if it can or should
be performed on the product.
Technical Service Manager
Delta Machinery
4825 Highway 45 North
Jackson, TN 38305
(IN CANADA: 505 SOUTHGATE DRIVE, GUELPH, ONTARIO N1H 6M7)
WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY
1. FOR YOUR OWN SAFETY, READ INSTRUCTION
MANUAL BEFORE OPERATING THE TOOL. Learn the
tool’s application and limitations as well as the specific
hazards peculiar to it.
2. KEEP GUARDS IN PLACE and in working order.
3. ALWAYS WEAR EYE PROTECTION.
4. REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that keys and adjusting
wrenches are removed from tool before turning it “on”.
5. KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
6. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t
use power tools in damp or wet locations, or expose them
to rain. Keep work area well-lighted.
7. KEEP CHILDREN AND VISITORS AWAY. All children
and visitors should be kept a safe distance from work area.
8. MAKE WORKSHOP CHILDPROOF – with padlocks,
master switches, or by removing starter keys.
9. DON’T FORCE TOOL. It will do the job better and be
safer at the rate for which it was designed.
10. USE RIGHT TOOL. Don’t force tool or attachment to
do a job for which it was not designed.
11. WEAR PROPER APPAREL. No loose clothing, gloves,
neckties, rings, bracelets, or other jewelry to get caught in
moving parts. Nonslip footwear is recommended. Wear
protective hair covering to contain long hair.
12.
ALWAYS USE SAFETY GLASSES. Wear safety
glasses. Everyday eyeglasses only have impact resistant
lenses; they are not safety glasses. Also use face or dust
mask if cutting operation is dusty. These safety glasses
must conform to ANSI Z87.1 requirements. Note:
Approved glasses have Z87 printed or stamped on
them.
13. SECURE WORK. Use clamps or a vise to hold work
when practical. It’s safer than using your hand and frees
both hands to operate tool.
14. DON’T OVERREACH. Keep proper footing and
balance at all times.
15. MAINTAIN TOOLS IN TOP CONDITION. Keep tools
sharp and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.
16. DISCONNECT TOOLS before servicing and when
changing accessories such as blades, bits, cutters, etc.
17. USE RECOMMENDED ACCESSORIES. The use of
accessories and attachments not recommended by Delta
may cause hazards or risk of injury to persons.
18. REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure switch is in “OFF” position before
plugging in power cord.
19. NEVER STAND ON TOOL. Serious injury could occur
if the tool is tipped or if the cutting tool is accidentally
contacted.
20. CHECK DAMAGED PARTS. Before further use of the
tool, a guard or other part that is damaged should be
carefully checked to ensure that it will operate properly and
perform its intended function – check for alignment of
moving parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that may affect its
operation. A guard or other part that is damaged should be
properly repaired or replaced.
21. DIRECTION OF FEED. Feed work into a blade or
cutter against the direction of rotation of the blade or cutter
only.
22. NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN POWER OFF. Don’t leave tool until it comes to a
complete stop.
23. DRUGS, ALCOHOL, MEDICATION. Do not operate
tool while under the influence of drugs, alcohol or any
medication.
24. MAKE SURE TOOL IS DISCONNECTED FROM
POWER SUPPLY while motor is being mounted,
connected or re-connected.
25. THE DUST GENERATED by certain woods and wood
products can be injurious to your health. Always operate
machinery in well ventilated areas and provide for proper
dust removal. Use wood dust collection systems whenever
possible.
26.
WARNING: SOME DUST CREATED BY
POWER SANDING, SAWING, GRINDING, DRILLING,
AND OTHER CONSTRUCTION ACTIVITIES contains
chemicals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals
are:
· lead from lead-based paints,
· crystalline silica from bricks and cement and other
masonry products, and
· arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as
those dust masks that are specially designed to filter out
microscopic particles.
SAVE THESE INSTRUCTIONS. Refer to them
often and use them to instruct others.
3
1. DO NOT OPERATE the tool until it is completely
assembled and installed according to the instructions.
2. IF YOU ARE NOT thoroughly familiar with the oper-
ation of jointers, obtain advice from your supervisor,
instructor or other qualified person.
3. KEEP cutterhead sharp and free of all rust and pitch.
4. BEFORE starting machine, check cutterhead and
drive guards to be sure they are in place and in proper
operating condition.
5. ALWAYS make sure exposed cutterhead behind the
fence is guarded, especially when jointing near the edge.
6. NEVER perform jointing or planing operations with
the cutterhead guard or drive guard removed.
7. MAKE CERTAIN the infeed table is tightened before
starting the machine.
8. NEVER start the jointer with the workpiece
contacting the cutterhead.
9. ALWAYS hold the workpiece firmly against the
tables and fence.
10. NEVER perform any operation “free-hand” which
means using your hands to support or guide the workpiece. ALWAYS use the fence to position and guide the
work.
11. AVOID awkward operations and hand positions
where a sudden slip could cause your hand to move into
the cutterhead.
12. ALWAYS use hold-down/push blocks for jointing
material less than 3 inches in height or planing material
thinner than 3 inches.
13. DO NOT perform jointing operations on material
shorter than 10 inches, narrower than 3/4 inch or less
than 1/2 inch thick.
14. DO NOT perform planing operations on material
shorter than 10 inches, narrower than 3/4 inch, wider
than 6 inches or less than 1/2 inch thick.
15. NEVER make jointing or planing cuts deeper than
1/8 inch. On cuts more than 1-1/2 inches wide, adjust
depth of cut to 1/16 inch or less to avoid overloading
machine and to minimize chance of kick-back (work
thrown back toward you).
16. MAINTAIN the proper relationship of infeed and
outfeed table surfaces and cutterhead knife path.
17. SUPPORT the workpiece adequately at all times
during operation; maintain control of the work at all
times.
18. DO NOT back the workpiece toward the infeed
table.
19. DO NOT attempt to perform an abnormal or little-
used operation without study and the use of adequate
hold-down/push blocks, jigs, fixtures, stops, etc.
20. SHUT OFF power before servicing or adjusting
tool and in the event of a power failure.
21. DISCONNECT tool from power source and clean the
machine before leaving it.
22. MAKE SURE the work area is clean before leaving
the machine.
23. SHOULD any part of your tool be missing, damaged,
or fail in any way, or any electrical component fail to
perform properly, shut off switch and remove plug from
power supply outlet. Replace missing, damaged or failed
parts before resuming operation.
24. THE USE of attachments and accessories not rec-
ommended by Delta may result in the risk of injuries.
25. IMPORTANT: When the tool is not in use, the
switch should be locked in the “OFF” position to
prevent unauthorized use.
26. ADDITIONAL INFORMATION regarding the safe
and proper operation of this product is available from the
National Safety Council, 1121 Spring Lake Drive, Itasca,
IL 60143-3201 in the Accident Prevention Manual for
Industrial Operation and also in the Safety Data Sheets
provided by the NSC. Please also refer to the American
National Standard Institute ANSI 01.1 Safety Requirements for Woodworking Machinery and the U.S. Department of Labor OSHA 1910.213 Regulations.
ADDITIONAL SAFETY RULES FOR JOINTERS
4
CONNECTING TOOL TO POWER SOURCE
POWER CONNECTIONS
A separate electrical circuit should be used for your tools. This circuit should not be less than #12 wire and should be
protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3prong grounding type plugs and 3-hole receptacles which accept the tool’s plug. Before connecting the motor to the
power line, make sure the switch is in the “OFF” position and be sure that the electric current is of the same
characteristics as indicated on the tool. All line connections should make good contact. Running on low voltage will
damage the motor.
MOTOR SPECIFICATIONS
Your tool is wired for 120 volt, 60 HZ alternating current. Before connecting the tool to the power source, make sure
the switch is in the “OFF” position. The no-load speed of the motor is 6000 - 11000 RPM.
GROUNDING INSTRUCTIONS
WARNING: THIS TOOL MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM
ELECTRIC SHOCK.
Fig. AA Fig. BB
GROUNDED OUTLET BOX
CURRENT
CARRYING
PRONGS
GROUNDING BLADE
IS LONGEST OF THE 3 BLADES
GROUNDED OUTLET BOX
GROUNDING
MEANS
ADAPTER
2. Grounded, cord-connected tools intended for use on
a supply circuit having a nominal rating less than 150
volts:
This tool is intended for use on a circuit that has an outlet
that looks like the one illustrated in Fig. AA. The tool has a
grounding plug that looks like the plug illustrated in Fig.
AA. A temporary adapter, which looks like the adapter
illustrated in Fig. BB, may be used to connect this plug a
2-hole receptacle as shown in Fig. BB if a properly
grounded outlet is not available. The temporary adapter
should be used only until a properly grounded outlet can
be installed by a qualified electrician. The green-colored
rigid ear, lug, and the like, extending from the adapter
must be connected to a permanent ground such as a
properly grounded outlet box. Whenever the adapter is
used, it must be held in place with a metal screw.
NOTE: In Canada, the use of a temporary adapter is not
permitted by the Canadian Electric Code.
WARNING: IN ALL CASES, MAKE CERTAIN THE
RECEPTACLE IN QUESTION IS PROPERLY
GROUNDED. IF YOU ARE NOT SURE HAVE A
QUALIFIED ELECTRICIAN CHECK THE RECEPTACLE.
1. All grounded, cord-connected tools:
In the event of a malfunction or breakdown, grounding
provides a path of least resistance for electric current to
reduce the risk of electric shock. This tool is equipped
with an electric cord having an equipment-grounding
conductor and a grounding plug. The plug must be
plugged into a matching outlet that is properly installed
and grounded in accordance with all local codes and
ordinances.
Do not modify the plug provided - if it will not fit the outlet,
have the proper outlet installed by a qualified electrician.
Improper connection of the equipment-grounding
conductor can result in risk of electric shock. The
conductor with insulation having an outer surface that is
green with or without yellow stripes is the equipmentgrounding conductor. If repair or replacement of the
electric cord or plug is necessary, do not connect the
equipment-grounding conductor to a live terminal.
Check with a qualified electrician or service personnel if
the grounding instructions are not completely
understood, or if in doubt as to whether the tool is
properly grounded.
Use only 3-wire extension cords that have 3-prong
grounding type plugs and 3-hole receptacles that accept
the tool’s plug, as shown in Fig. AA.
Repair or replace damaged or worn cord immediately.
HOLES
HOLES
Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord which
has a 3-prong grounding type plug and a 3-hole receptacle which will accept the tool’s plug. When using an extension
cord, be sure to use one heavy enough to carry the current of the tool. An undersized cord will cause a drop in line
voltage, resulting in loss of power and overheating. Fig. DD, shows the correct gauge to use depending on the cord
length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
EXTENSION CORDS
OPERATING INSTRUCTIONS
FOREWORD
Delta Model 37-070 is a 6" Variable Speed Bench Jointer with designed cutting capacity of 6" (152mm) width and 1/8"
(3mm) depth. Unit includes; 10 amp, 120 volt motor with variable speed range from 6000 to 11,000 rpm and cutting
speed range from 12,000 to 22,000 cpm, dust chute, center-mounted fence, two-knife cutterhead, cutterhead guard and
lock, wrenches and push blocks.
UNPACKING AND CLEANING
Carefully unpack the tool and all loose items from the shipping container(s). Remove the protective coating from all
unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline
or lacquer thinner for this purpose). After cleaning, cover the unpainted sufaces with a good quality household floor paste
wax.
5
Fig. DD
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC TOOLS
Ampere Volts Total Length of Gauge of
Rating Cord in Feet Extension Cord
0-6 120 up to 25 18 AWG
0-6 120 25-50 16 AWG
0-6 120 50-100 16 AWG
0-6 120 100-150 14 AWG
6-10 120 up to 25 18 AWG
6-10 120 25-50 16 AWG
6-10 120 50-100 14 AWG
6-10 120 100-150 12 AWG
10-12 120 up to 25 16 AWG
10-12 120 25-50 16 AWG
10-12 120 50-100 14 AWG
10-12 120 100-150 12 AWG
12-16 120 up to 25 14 AWG
12-16 120 25-50 12 AWG
12-16 120
GREATER THAN 50 FEET NOT RECOMMENDED
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC TOOLS
Ampere Volts Total Length of Gauge of
Rating Cord in Feet Extension Cord
0-6 240 up to 50 18 AWG
0-6 240 50-100 16 AWG
0-6 240 100-200 16 AWG
0-6 240 200-300 14 AWG
6-10 240 up to 50 18 AWG
6-10 240 50-100 16 AWG
6-10 240 100-200 14 AWG
6-10 240 200-300 12 AWG
10-12 240 up to 50 16 AWG
10-12 240 50-100 16 AWG
10-12 240 100-200 14 AWG
10-12 240 200-300 12 AWG
12-16 240 up to 50 14 AWG
12-16 240 50-100 12 AWG
12-16 240
GREATER THAN 100 FEET NOT RECOMMENDED
Fig. DD
6
DEFINITIONS OF
JOINTING AND PLANING OPERATIONS
Fig. 2
Fig. 3
1. JOINTING OPERATIONS – Jointing cuts or edge
jointing are made to square an edge of a workpiece. The
workpiece is positioned on the jointer with the narrow
edge of the workpiece on the infeed table and the major
flat surface of the workpiece against the fence, as shown
in Fig. 2. The workpiece is moved from the infeed table,
across the cutterhead to the outfeed table.
2. PLANING OPERATIONS – Planing or surfacing are
identical to the jointing operation except for the position
of the workpiece. For planing, the major flat surface of
the workpiece is placed on the infeed table of the jointer
with the narrow edge of the workpiece against the fence,
as shown in Fig. 3. The workpiece is moved from the
infeed table, across the cutterhead to the outfeed table.
Use push blocks when performing planing operations
whenever possible.
7
Fig. 4
1 - Jointer
2 - Fence
3 - Fence Sliding Bracket
4 - Special Nut (for assembling Fence Sliding Bracket to Fence Mounting Bracket)
5 - Flat Washer (for assembling Fence Sliding Bracket to Fence Mounting Bracket)
6 - Spring Loaded Lock Handle (for assembling Fence Sliding Bracket to Fence Mounting Bracket)
7 - 5/8" long Socket Button Head Screw (for assembling Fence to Fence Sliding Bracket) -(2)
8 - T-Nut (for assembling Fence to Fence Sliding Bracket) -(2)
9 - Fence Mounting Bracket
10 - 5/8" long Socket Button Head Screw (for assembling Fence Mounting Bracket to Jointer Base)- (4)
11 - Push Blocks - (2)
12 - Cutterhead Guard
13 - Cutterhead Lock
14 - 7/16" long Socket Button Head Screw (for assembling Cutterhead Lock to Jointer Base)
15 - 7/16" long Socket Button Head Screw (for assembling Cutterhead Guard to Jointer Base) - (2)
16 - Allen Wrenches - (2)
1
2
3
4
5
6
7
8
9
11
12
13
16
15
14
10
8
Fig. 5
Fig. 6
Fig. 7
Fig. 8
2. Assemble the fence sliding bracket (C) Fig. 7, to
mounting bracket (A) using the lockhandle (D), flat
washer (E) and special nut (F) Fig. 8.
ASSEMBLING FENCE
1. Assemble the fence mounting bracket (A) Fig. 5, to
the jointer base using the four 5/8" long socket button
head screws (B) Fig. 6.
ASSEMBLY INSTRUCTIONS
WARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE TOOL TO THE POWER
SOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED AND YOU HAVE READ AND
UNDERSTAND THE ENTIRE OWNERS MANUAL.
A
B
B
C
D
E
A
F
9
9
Fig. 9
Fig. 10
Fig. 11
Fig. 12
6. Tighten two screws (G) Fig. 12.
5. Position fence (L) Fig. 11, so that rounded section
(M) on bottom of fence is over cutterhead opening as
shown.
4. Slide groove of fence (L) Fig. 10, over T-nuts (J) as
shown.
3. Assemble 5/8" long socket button head screw (G)
Fig. 9, to fence tilting bracket (H) and thread T-nut (J)
onto threaded end of screw (G) as shown. DO NOT
COMPLETELY TIGHTEN SCREW (G) AT THIS TIME.
Assemble screw and T-nut to opposite end of tilting
bracket in the same manner.
H
J
G
L
J
M
L
G
G
10
Fig. 13
Fig. 14
Fig. 15
Fig. 16
ASSEMBLING
CUTTERHEAD GUARD
1. Thread the two 7/16" long socket button head
screws (A) Fig. 13, into the two threaded holes in front
side of jointer base. DO NOT COMPLETELY TIGHTEN
SCREWS (A) AT THIS TIME.
2. Assemble guard mounting bracket (B) Fig. 14, to the
two screws (A) as shown, and tighten the two screws (A).
ASSEMBLING
CUTTERHEAD LOCK
1. Assemble cutterhead lock (A) Fig. 15, to the front
side of the jointer base, using the 7/16" long socket
button head screw (B). NOTE: THE CUTTERHEAD
LOCK (A) IS TO BE ENGAGED WITH THE
CUTTERHEAD SHAFT AS SHOWN IN FIG. 15. ONLY
WHEN SETTING KNIVES. ALL OTHER TIMES THE
CUTTERHEAD LOCK (A) SHOULD BE DISENGAGED
FROM THE CUTTERHEAD, AS SHOWN IN FIG. 16.
A
B
A
A
A
B
A
11
Fig. 22
Fig. 21
FASTENING JOINTER TO SUPPORTING SURFACE
If during operation, there is any tendency for the jointer
to tip over, slide or walk on the supporting surface, the
jointer must be secured to the supporting surface with
fasteners through the four holes, two of which are
shown at (A) Fig. 20, in the jointer base.
STARTING AND
STOPPING JOINTER
The on/off switch (A) Fig. 21, is located on the front of the
jointer cabinet. To turn the machine “ON,” move the
switch (A) to the up position. To turn the machine “OFF,”
move the switch (A) to the down position.
OPERATING CONTROLS AND ADJUSTMENTS
LOCKING SWITCH IN
THE “OFF” POSITION
IMPORTANT: When the tool is not in use, the switch
should be locked in the “OFF” position to prevent
unauthorized use. Grasp the switch toggle (B) and pull
it out as shown in Fig. 22. With the switch toggle (B)
removed, the switch will not operate. However, should
the switch toggle be removed while the machine is
running, it can be turned “OFF” once, but cannot be
restarted without inserting the switch toggle (B).
A
B
Fig. 20
A
A
12
VARIABLE SPEED CONTROL
Your jointer is supplied with a variable speed control
knob (A) Fig. 23, that enables you to operate the machine
at cutterhead speeds between 6000 and 11,000 RPM.
Speed indicators of 1-2-3-4 and 5 are provided on the
speed dial as shown. When the pointer (B) is pointing to
1, the cutterhead speed will be 6000 RPM; 2 – 7250
RPM; 3 – 8800 RPM; 4 – 9750 RPM; and 5 – 11,000
RPM.
SPEED CONTROL CHART
A speed control chart (C) Fig. 23, indicates the recommended cutterhead speed setting when jointing plastics,
soft woods and hard woods from 1-1/2" to 6" wide.
DEPTH OF
CUT ADJUSTMENT
The jointer can be set to cut any depth from a very thin
shaving to 1/8" deep. A dual English/Metric scale (A)
Fig. 24, and pointer (B) are provided to indicate the depth
of cut. To adjust for depth of cut, loosen lock knob (C)
and turn adjusting knob (D) clockwise to lower and counterclockwise to raise the infeed table. After the infeed
table is at the desired setting, tighten lock knob (C).
NOTE: For best results, final positioning of the infeed
table should always be made from the bottom to the up
position.
FENCE ADJUSTMENTS
The fence can be moved across the table and can be
tilted up to 45 degrees to the right, as follows:
1. To move the fence across the table, loosen lock lever
(A) Fig. 25, slide the fence to the desired position on the
table and tighten lever (A). NOTE: Lock lever (A) is spring
loaded and can be repositioned by pulling up on the
lever and repositioning it on the nut located underneath
the lever.
2. To tilt the fence, loosen lever (B) Fig. 25, and tilt the
fence to the desired angle. Then tighten lever (B). NOTE:
Lever (B) is spring loaded and can be repositioned by
pulling out on the lever and repositioning it on the nut
located underneath the lever.
Fig. 23
Fig. 24
Fig. 25
C
A
B
D
C
A
B
A
B
13
Fig. 26
Fig. 27
Fig. 28
Fig. 29
3. The fence features adjustable positive stops at the
most used fence positions of 90 degrees and 45 degrees
to the right. To check and adjust the positive stops,
proceed as follows:
4. Place a square (C) Fig. 26, on the table with one end
of the square against the fence as shown. Adjust the
fence until it is exactly 90 degrees to the table.
5. Turn set screw (D) Fig. 27, until it contacts stop (E).
6. Using a square (C) Fig. 28, tilt the table to the 45
degree position and make sure the fence is 45 degrees
to the table. Adjust the fence if necessary.
7. Turn set screw (F) Fig. 29, until it contacts stop (G).
8. These positive stops enable you to rapidly position
the table to the 90 and 45 degree settings.
CAUTION: MAKE SURE THE FENCE IS IN LEVEL
CONTACT WITH THE SURFACE OF THE OUTFEED
TABLE.
C
D
E
C
G
H
14
Fig. 30
ADJUSTING KNIVES
When it becomes necessary to adjust the knives due to
replacement or wear, proceed as follows:
1. DISCONNECT THE TOOL FROM THE POWER
SOURCE AND REMOVE CUTTERHEAD GUARD.
2. Rotate cutterhead and loosen four screws (A) Fig.
30. NOTE: Do not overly loosen the screws (A). Loosen
one half turn or only enough so knife can slide between
locking plate and cutterhead.
3. Rotate cutterhead and engage cutterhead lock (B)
Fig. 31, on cutterhead shaft as shown. This will position
knives for proper adjustment to the outfeed table.
4. Place a straight edge (C) Fig. 31, on the outfeed table
extending out over the knife as shown. Using wrench (D)
supplied, turn screw (E) until knife just touches straight
edge. Adjust knife at far end of cutterhead in the same
manner turning screw (F). Tighten four screws (A) Fig. 30,
after adjustment is made.
5. Adjust remaining knife in the same manner and
MAKE SURE CUTTERHEAD LOCK (B) IS DISENGAGED AFTER ADJUSTMENT IS COMPLETED AND
REPLACE CUTTERHEAD GUARD.
Fig. 32
6. The following are examples of what will happen if the
knives are not adjusted properly.
7. If the knives are set too low, the result will be as
shown in Fig. 32, and the finished surface will be curved.
KNIVES
SET TOO LOW
OUT-FEED
TABLE
IN-FEED TABLE
CUTTER
A
MATERIAL
Fig. 31
C
B
D
F
E
15
Fig. 36
Fig. 35
Fig. 34
Fig. 33
CORD STORAGE
A cord storage bracket (A) Fig. 36, is provided on jointer
base for storage of the cord when machine is not in use.
CHIP AND DUST CHUTE
A chip and dust chute (A) Fig. 35, is provided on the
outfeed end of the jointer base for efficient chip removal.
CAUTION: KEEP HANDS OUT OF CHIP AND DUST
CHUTE AT ALL TIMES.
9. As a final check, run a piece of work slowly over the
knives for 6 to 8 inches. The wood should rest firmly on
both tables as shown in Fig. 34, with no open spaces
under the finished cut.
8. If the knives are set too high, the work will be gouged
at the end of the cut, as shown in Fig. 33.
KNIVES
SET TOO HIGH
IN-FEED TABLE
OUT-FEED
TABLE
CUTTER
IN-FEED TABLE
CUTTER
OUT-FEED
TABLE
KNIVES AT
CORRECT HEIGHT
A
A
GOUGE
MATERIAL
MATERIAL
16
Fig. 39 Fig. 39A
PUSH BLOCKS
A set of push blocks (A) Fig. 37, is supplied with your
jointer and should be used whenever possible to
minimize all danger to your hands. Fig. 37, illustrates
using the push blocks properly.
JOINTING AN EDGE
This is the most common operation for the jointer. Set the guide fence square with the table.
Depth of cut should be the minimum required to obtain a straight edge. Hold the best face of the
piece firmly against the fence throughout the feed as shown in Fig. 39.
DO NOT PERFORM JOINTING OPERATIONS ON MATERIAL SHORTER THAN 10 INCHES,
NARROWER THAN 3/4 INCH, OR LESS THAN 1/2 INCH THICK (REFER TO FIG. 39A).
OPERATION
The following directions will give the beginner a start on jointer operations. Use scrap pieces of lumber to check the
settings and to get the feel of the operations before attempting regular work.
WARNING: ALWAYS USE CUTTERHEAD GUARD AND KEEP HANDS AWAY FROM CUTTERHEAD. USE
PUSH BLOCKS WHENEVER POSSIBLE.
PLACEMENT OF HANDS
DURING FEEDING
At the start of the cut, the left hand holds the work firmly
against the infeed table and fence, while the right hand
pushes the work toward the knives. After the cut is underway, the new surface rests firmly on the outfeed table
as shown in Fig. 38. The left hand should then be moved
to the work on the outfeed table, at the same time
maintaining flat contact with the fence. The right hand
presses the work forward, and before the right hand
reaches the cutterhead it should be moved to the work
on the outfeed table. CAUTION: NEVER PASS HANDS
DIRECTLY OVER THE CUTTERHEAD.
Fig. 38
OUT-FEED
TABLE
IN-FEED TABLE
CUTTER
3/4" MINIMUM
10" MINIMUM
MINIMUM JOINTING DIMENSIONS
1/2"
MINIMUM
Fig. 37
A
MATERIAL
17
Fig. 42
Fig. 41
Fig. 40A
PLANING WARPED PIECES
If the wood to be planed is dished or warped, take light cuts until the surface is flat. Avoid forcing such material down
against the table; excessive pressure will spring it while passing the knives, and it will spring back and remain curved
after the cut is completed.
PLANING SHORT
OR THIN WORK
When planing short or thin pieces, always use push
blocks to minimize all danger to the hands. Fig. 40,
illustrates using the Push Blocks properly.
DO NOT PERFORM PLANING OPERATIONS ON
MATERIAL SHORTER THAN 10 INCHES, NARROWER
THAN 3/4 INCH, WIDER THAN 6 INCHES, OR LESS
THAN 1/2 INCH THICK (REFER TO FIG. 40A).
DIRECTION OF GRAIN
Avoid feeding work into the jointer against the grain as
shown in Fig. 41. The result will be chipped and
splintered edges. Feed with the grain as shown in Fig.
42, to obtain a smooth surface.
CORRECT FEED - WITH THE GRAIN
IN-FEED TABLE
OUT-FEED
TABLE
CUTTER
IN-FEED TABLE
OUT-FEED
TABLE
CUTTER
WRONG FEED - AGAINST THE GRAIN
MINIMUM AND MAXIMUM PLANING DIMENSIONS
1/2"
MINIMUM
3/4" MINIMUM
6" MAXIMUM
10" MINIMUM
Fig. 40
MATERIAL
MATERIAL
18
MAINTENANCE
BELT REPLACEMENT
When it becomes necessary to replace the belt on your
jointer, proceed as follows:
1. DISCONNECT THE TOOL FROM THE POWER
SOURCE.
2. Remove screw (A) Fig. 43, using Allen wrench
supplied, and remove belt guard (B).
3. Loosen three screws (C) Fig. 44, to release belt
tension and remove belt (D) from pulleys.
4. Assemble new belt to the cutterhead and motor
pulleys. Press down on motor pulley (E) Fig. 44, to
tension belt and tighten three screws (C).
5. Replace belt guard (B) Fig. 44.
Fig. 43
Fig. 44
B
A
D
E
C
C
C
B
Delta Building Trades and Home Shop Machinery
Two Year Limited Warranty
Delta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory which
in normal use has proven to be defective in workmanship or material, provided that the customer returns the product
prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two
years and provides Delta with reasonable opportunity to verify the alleged defect by inspection. Delta may require that
electric motors be returned prepaid to a motor manufacturer’s authorized station for inspection and repair or replacement.
Delta will not be responsible for any asserted defect which has resulted from normal wear, misuse, abuse or repair or
alteration made or specifically authorized by anyone other than an authorized Delta Service facility or representative. Under
no circumstances will Delta be liable for incidental or consequential damages resulting from defective products. This
warranty is Delta’s sole warranty and sets forth the customer’s exclusive remedy, with respect to defective products; all
other warranties, express or implied, whether of merchantability, fitness for purpose, or otherwise, are expressly
disclaimed by Delta.
PARTS, SERVICE OR WARRANTY ASSISTANCE
All Delta Machines and accessories are manufactured to high quality standards and are serviced by a network
of Porter-Cable • Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional
information regarding your Delta quality product or to obtain parts, service, warranty assistance, or the location
of the nearest service outlet, please call 1-800-223-7278 (In Canada call 1-800-463-3582).
ACCESSORIES
A complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers, and
Delta Authorized Service Stations. Please visit our Web Site www.deltamachinery.com for a catalog or for the name
of your nearest supplier.
WARNING: Since accessories, other than those offered by Delta, have not been tested
with this product, use of such accessories could be hazardous. For safest operation, only
Delta recommended accessories should be used with this product.
37-108 Push Blocks
19
20
NOTES
The following are trademarks of PORTER-CABLE DELTA Corporation (Las siguientes son marcas registradas de PORTER-CABLE S.A.):
BAMMER
®
, INNOVATION THAT WORKS®, JETSTREAM®, LASERLOC®, OMNIJIG®, POCKET CUTTER®, PORTA-BAND®, PORTA-PLANE®,
PORTER-CABLE®, QUICKSAND®, SANDTRAP®, SAW BOSS®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR-EASE®, THE
PROFESSIONAL EDGE
®
, THE PROFESSIONAL SELECT®, TIGER CUB®, TIGER SAW®, TORQBUSTER®, WHISPER SERIES®, DURATRONIC™,
FLEX™, FRAME SAW™, MICRO-SET™, MORTEN™, NETWORK™, RIPTIDE™, TRU-MATCH™, WOODWORKER’S CHOICE™.
Trademarks noted with ® are registered in the United States Patent and Trademark Office and may also be registered in other countries.
Las Marcas Registradas con el signo de ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden
estar registradas en otros países.
PORTER-CABLE DELTA SERVICE CENTERS
(CENTROS DE SERVICIO DE PORTER-CABLE
DELTA)
Parts and Repair Service for Porter-Cable/Delta Power Tools are Available at These Locations
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable Delta)
Authorized Service Stations are located in many large cities. Telephone 800-487-8665 or 731-541-6042 for assistance locating one.
Parts and accessories for Porter-Cable Delta products should be obtained by contacting any Porter-Cable Delta Distributor,
Authorized Service Center, or Porter-Cable Delta Factory Service Center. If you do not have access to any of these, call 888-848-5175
and you will be directed to the nearest Porter-Cable Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están
ubicadas en muchas grandes ciudades. Llame al 800-487-8665 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las
piezas y los accesorios para los productos Porter-Cable Delta deben obtenerse poniéndose en contacto con cualquier distribuidor
Porter-Cable Delta, Centro de Servicio Autorizado o Centro de Servicio de Fábrica Porter-Cable Delta. Si no tiene acceso a ninguna
de estas opciones, llame al 888-848-5175 y le dirigirán al Centro de Servicio de Fábrica Porter-Cable Delta más cercano.
ARIZONA
Tempe 85282 (Phoenix)
2400 West Southern Avenue
Suite 105
Phone: (602) 437-1200
Fax: (602) 437-2200
CALIFORNIA
Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: (909) 390-5555
Fax: (909) 390-5554
San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: (510) 357-9762
Fax: (510) 357-7939
FLORIDA
Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
Phone: (954) 321-6635
Fax: (954) 321-6638
Tampa 33609
4538 W. Kennedy Boulevard
Phone: (813) 877-9585
Fax: (813) 289-7948
GEORGIA
Forest Park 30297 (Atlanta)
5442 Frontage Road,
Suite 112
Phone: (404) 608-0006
Fax: (404) 608-1123
ILLINOIS
Addison 60101 (Chicago)
311 Laura Drive
Phone: (630) 628-6100
Fax: (630) 628-0023
Woodridge 60517 (Chicago)
2033 West 75th Street
Phone: (630) 910-9200
Fax: (630) 910-0360
MARYLAND
Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: (410) 799-9394
Fax: (410) 799-9398
MASSACHUSETTS
Braintree 02185 (Boston)
719 Granite Street
Phone: (781) 848-9810
Fax: (781) 848-6759
Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: (508) 520-8802
Fax: (508) 528-8089
MICHIGAN
Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: (248) 597-5000
Fax: (248) 597-5004
MINNESOTA
Minneapolis 55429
4315 68th Avenue North
Phone: (763) 561-9080
Fax: (763) 561-0653
MISSOURI
North Kansas City 64116
1141 Swift Avenue
P.O. Box 12393
Phone: (816) 221-2070
Fax: (816) 221-2897
St. Louis 63119
7574 Watson Road
Phone: (314) 968-8950
Fax: (314) 968-2790
NEW YORK
Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: (718) 225-2040
Fax: (718) 423-9619
NORTH CAROLINA
Charlotte 28270
9129 Monroe Road, Suite 115
Phone: (704) 841-1176
Fax: (704) 708-4625
OHIO
Columbus 43214
4560 Indianola Avenue
Phone: (614) 263-0929
Fax: (614) 263-1238
Cleveland 44125
8001 Sweet Valley Drive
Unit #19
Phone: (216) 447-9030
Fax: (216) 447-3097
OREGON
Portland 97230
4916 NE 122 nd Ave.
Phone: (503) 252-0107
Fax: (503) 252-2123
PENNSYLVANIA
Willow Grove 19090
520 North York Road
Phone: (215) 658-1430
Fax: (215) 658-1433
TEXAS
Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: (972) 446-2996
Fax: (972) 446-8157
Houston 77055
West 10 Business Center
1008 Wirt Road, Suite 120
Phone: (713) 682-0334
Fax: (713) 682-4867
WASHINGTON
Renton 98055 (Seattle)
268 Southwest 43rd Street
Phone: (425) 251-6680
Fax: (425) 251-9337
Printed in U.S.A.
ALBERTA
Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
Phone: (403) 735-6166
Fax: (403) 735-6144
BRITISH COLUMBIA
8520 Baxter Place
Burnaby, B.C.
V5A 4T8
Phone: (604) 420-0102
Fax: (604) 420-3522
MANITOBA
1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
Phone: (204) 633-9259
Fax: (204) 632-1976
ONTARIO
505 Southgate Drive
Guelph, Ontario
N1H 6M7
Phone: (519) 836-2840
Fax: (519) 767-4131
QUÉBEC
1515 ave.
St-Jean Baptiste,
Québec, Québec
G2E 5E2
Phone: (418) 877-7112
Fax: (418) 877-7123
1447, Begin
St-Laurent, (Montréal), Québec
H4R 1V8
Phone: (514) 336-8772
Fax: (514) 336-3505
Loading...