6.00
16°C 16°C
20°C 20°C 20°C
18°C 18°C
8.00 11.00 13.00
17.00
23.000.00
P1
P2 P3 P4 P5 P6
TYBOX 217 - 227 - 237
327 - 337
www.deltadore.com
Important product
information (➋➍)
AUTO
2004/108/CE - 2006/95/CE
R&TTE 1999/5/CE
TYBOX 3x7
h (ON)
023
4
TYBOX follows the program.
Information button
i
Room temperature
Operating hours counter (boiler)
This meter can be reset (see installation guide)
Press time
Program «Once»
Weekly programming
2 daily programs (week + week-end)
PROG
PROG
x7
> 3s
6.00
16°C 16°C
20°C
23.000.00
P1
P6
PROG
TYBOX follows the program «Once».
PROG
5+2
Reset
Menu 2-17
Turn the selector dial to AUTO.
Your thermostat follows
the programme.
Depending on the configuration during installation,
your device will constantly display the temperature
setting or the room temperature.
To change these settings, refer to the "installation
guide" or contact your installation engineer.
In AUTO mode, pressing the i button displays the room temperature or the temperature
setting, depending on the configuration during installation.
Pressing the button a second time displays the number of hours for which the boiler has
operated, as well as the number of days remaining before boiler maintenance.
Interval before maintenance
of the boiler
Outdoor temperature
Temperature setting
Return to
automatic mode
*2703294_Rev2en*
1
31
1
12
0
23
0
59
2012 ...
EXIT
1
2
3
4
5
8
9
10
11
6
7
Time setting
1
31
5°C
15°C
18/02/2012
00.00
Absence mode
Enter the return date
Example
Countdown
Turn the selector dial to .
The days flash.
Press + or - to select the day, then press OK
to confirm and move on to the next setting.
Repeat the process to set
the hours and minutes.
This mode protects your home from frost if you are absent for several days.
Turn the selector dial and enter the return date.
Confirmation
Return to AUTO mode
at the end of the
countdown,
at 00:00,18/02.
The Frost
Protection
setting is
adjustable
STOP
This mode is used to switch your heating
installation off. Turn the selector dial to .
In this mode, the device displays the room
temperature.
To change the mode in progress, press OK again.
To cancel the current absence mode, turn the selector dial.
To exit the
"time setting" mode,
turn the selector dial.
1
7
P1
P6
5°C
30°C
00:00
23:45
6.00 8.00 11.00 13.00
17.00
23.000.00
P1
P2 P3 P4 P5 P6
PROG x7
6.00
16°C 16°C
19°C 20°C 20°C
18°C 18°C
8.00 11.00 13.00
17.00
23.000.00
P1
P2 P3 P4 P5 P6
16°C 16°C
20°C 20°C
18°C 18°C
PROG 5+2
1
2
3
1...5
6/7
1
2
3
4
5
6
7
8
9
1
3
2
PROG 5+2
EXIT
EXIT
PROG x 7
A
B
COPY
OR
>3s
1 2
3
PROG
E.g.
The program can be modified for each day.
Periods 2 to 5 can be disabled.
e.g. disabling of the midday slot (periods 3 and 4).
2 daily programmes: week (1 to 5) + weekend (6 and 7).
1 single programme for the 5 weekdays.
1 single programme for the weekend.
To change the programme, see above.
Confirm and continue on to the next day to program it
separately or confirm the program and copy it to the next day.
The programme may be weekly (PROG x7) or
daily (PROG 5+2). This choice is made using the switch
on the back of the device.
This programming can also be done in one-hour,
half-hour, or quarter-hour stages.
If you wish to change these settings, refer to the
"installation guide" or contact your installation engineer.
Select the programme stage to be disabled
(e.g.: P3)
Repeatedly press the
- button until the display shows "--:--"
Confirm by pressing OK
Repeat the operation for each time slot of
the programme that you wish to disable.
1
2
3
Programming can be done for one-hour, 30-minute or 15-minute
time slots (see "installation guide", menu 1-02).
Use the + and - buttons to make your choices.
Press OK to confirm and move on to the next setting
To exit the mode,
turn the selector dial.
To exit the mode,
turn the selector dial.
P1
P6
PROG (journée à la maison)
5°C
30°C
00:00
23:45
00:00
23:45
1
2
3
7.00
16°C 16°C20°C
23.000.00
P1
P6
EXIT
Replacing the batteries
6.00
16°C
16°C
20°C 20°C 20°C
18°C
8.00 11.00 13.00
13.54
17.00 23.000.00
P1
P2 P3 P4 P5 P6
13.54
AUTO
PROG
7.00
16°C 16°C20°C
23.000.00
P1
P6
21°C
18°C
Override
From AUTO mode or the "day at home" programme
Allows a given temperature setting to be applied until the next change of programme.
To apply a simplified program (two programmable periods, P1 and P6). This program can be modified.
You have approximately 30 seconds to change the
batteries before the time setting is reset
(if this happens, reprogramme the date and time).
When the batteries symbol appears. you have
approximately 1 month to change the batteries
(2 1.5 V LR03 or AAA alkaline batteries).
1
3
4
2
1,5V - LR03/AAA
(Alkaline)
1
Turn the selector dial to PROG
2
Press the - button to display the flashing symbol
Confirm by pressing OK
3
To exit the mode,
turn the selector dial.
Configure the "day at home" programme using the + and - buttons,
then press OK to confirm and move on to the next setting.
Loading...