Page 1
De’Longhi; June 2004 Issue 1
333IDL/06.04
SAN MARCO LILAC AND TORCELLO
Electric Focal Point Fires
Instructions for use
Please retain for future reference
Page 2
Thank you for choosing to purchase a De’Longhi fire. Please read the
instructions carefully in order to enjoy your product fully.
GENERAL INSTRUCTIONS
Remove the fire from the packaging, checking that neither the fire nor the
power cable have been damaged during transport. Do not operate the fire
if damaged.
Accessories - pebbles
alternative light filter – (San Marco Lilac only)
Spare light bulb.
The pebbles are found in the bottom of the carton under the brown
cardboard layer, so ensure that the accessories are removed before
discarding the boxes.
INSTALLATION OF THE FIRE
Your fire is designed for use within an existing chimney, or as part of a
fireplace a mantel and surround suite. The rebate depth is standard at 2 3/4
inches (7 cm) which should fit perfectly. If however you wish to apply it flush
to the wall (with no surround) a spacer frame is required.
If your model requires a spacer frame, it can be ordered from the Customer
Services: dept on 0845 6006845.
Position the fire so that the plug socket is accessible.
IMPORTANT: Access must be allowed for the fire to be serviced,
which involves the heater being moved forward in order to access the
rear. Sufficient mains lead must be available to allow the fire to be
moved for access when servicing.
Should you wish to connect the fire to a fused spur, this must be carried
out by a competent electrician in accordance with the IEE wiring
regulations.
Where the inset fire is being used in an existing chimney, it is important
that the chimney is blocked off to prevent airflow problems within the fire.
Where a chimney is not blocked off sufficiently the heater may cut out and
the flame effect stop, or work poorly.
Light pattern colour – SAN MARCO LILAC ONLY
The fire comes with a coloured light pattern. An alternative light pattern is
also included in the San Marco Lilac. Should you wish to change the
colour to turquoise, first ensure the heater is not plugged into the mains,
then unscrew the knob at the bottom of the fret panel and remove the fret
and lilac filter. Then place the white backing filter followed by the turquoise
filter in place of the lilac. Replace the fret and screw the knob up tightly.
Light pattern colours – accessory packs
Accessory pack consisting of different coloured light patterns; bulbs and
coal etc, can be purchased from De’Longhi;
Please contact Customer Services (0845 6006845) for more information.
Pebbles
Once the fire is installed in the correct position, unpack the pebbles from
the accessory box. The pebbles are natural; therefore variation in size,
shape and colour will occur.
Now arrange the pebbles. Place them to your liking using as many as
your require.
We suggest you place a medium sized pebble in each corner and then add 3
larger pebbles along the front, filling the gaps with smaller pebbles and building
to a slightly higher level in the centre of the fire.
Page 3
OPERATING THE FIRE
Controls
The on/off push button switch is located on the top right hand side of the
fire. Pushed in, it will illuminate the fire with no heat, so that you may enjoy
the flame effect all year round. Pushed again the switch will return to its
outer position and turn the fire off.
To use the heating element (the heater element is under the hood), press
the button marked with two bars.
The fire is 2kW and is thermostatically controlled. The thermostat is
positioned next to the heat switch.
We suggest that you turn the thermostat up to the maximum. Then, once
the required room temperature is achieved, turn the thermostat towards
minimum until you hear a click and the heater turns off. The thermostat will
then regulate the room temperature automatically.
Please note that there can be several 0C drop or rise in temperature to
activate or deactivate the thermostat. The temperature is taken from near to
the fire and therefore some fluctuations may arise. Other situations such as
the size of the room, the airflow within the room, and the proximity to other
heat sources may cause fluctuations in the thermostat’s efficiency.
Automatic Safety Cut Out
This heater is fitted with an automatic cut out to prevent any damage due
to overheating. The heater will automatically cut out if the airflow is
obstructed. To reset the fire, switch off the fire, remove the cause of
overheating and allow a suitable cooling period then switch the fire back
on.
Noise
As with all fan driven appliances the fire will make some noise due to the
movements of air occurring, this is perfectly normal.
MAINTENANCE
Before any maintenance / cleaning is undertaken always disconnect
the fire from the power supply.
Replacing light bulbs
San Marco Lilac and Torcello fires come fitted with two 60W daylight
(craftlight) bulbs. Replacements are available from good hardware/large
DIY stores. Allow a suitable time for the bulbs to cool and remove all the
pebbles/ coal. Then unscrew the knob at the base of the fire and remove
the fret, filter(s), and wire mesh. Now the bulbs can be changed (use bulbs
as described above). Please note that replacement bulbs are not covered
by the guarantee of the product.
Cleaning
The fire can be cleaned with a soft damp cloth. If you need to remove
fingerprints from the stainless steel, use a special stainless steel cleaner,
or a little baby oil or WD40 on a soft cloth.
WARNINGS
• Do not use the fire in a bathroom or in the vicinity of bathtubs,
washbasins, showers or swimming pools.
• Never use the fire to dry laundry.
• Never install the fire directly underneath a fixed mains socket.
• Never for any reason cover the appliance during operation.
• If the power cable is damaged, it must be replaced by the
manufacturer or an authorised technical service centre.
• The use of an extension lead is not recommended.
• Do not use the fire in rooms which have a floor area as small as 4m
2
• As with any electrical appliance, whilst the instructions aim to cover
as many eventualities as possible, caution and common sense should
be applied when operating your appliance, particularly in the vicinity
of small children.
• Particular caution should be applied to ensure that young children do
not play with or swallow any pebbles/coal.
• Should you wish to connect the fire to a fused spur, this must be
carried out by a competent electrician in accordance with the IEE
wiring regulations.
Page 4
PROBLEM SOLVING
No power to the fire Check the wall socket and plug
and fuse
No Illumination / flame effect Check that fire is switched on.
Check that the bulbs are working.
Heater cuts out / poor or no flame
effect
Check that the chimney is
blocked off above the fire
Outer frame sits away from fire
on delivery
There is a normal tolerance of
2mm to 6mm where the outer
frame sits around the fire. If the
frame has become dislodged in
transit it may be removed by
pulling upward and off (it is
attached by magnets) then
replaced back on the fire.
GUARANTEE
Your fire is guaranteed for 1 year from the date of purchase. In the unlikely
event of a breakdown you have access to our customer services team.
Simply call 0845 600 6845.
ELECTRICAL CONNECTION (UK Only)
Your appliance comes fitted with a plug and will incorporate a 13 amp fuse. If it does not fit your socket, the plug
should be cut off from the mains lead and an appropriate one fitted as below.
WARNING: Very carefully dispose of the cut off plug after removing the fuse: do not insert in a 13 amp socket
elsewhere in the house as this could cause a shock hazard. With alternative plugs not incorporating a fuse the circuit
must be protected by a 15 amp fuse.
If the plug is a moulded-on type, the fuse cover must be refitted when changing the fuse using a 13amp Astra
approved fuse to BS1362. In the event of losing the fuse cover, the plug must not be used until a replacement fuse
cover can be obtained from your nearest electrical dealer. The colour of the correct replacement fuse cover is that
marked on the base of the plug.
WARNING- THIS APPLIANCE MUST BE
EARTHED
IMPORTANT
The wires in the mains lead are coloured in accordance with
the following code;
As the colours of the wires in the mains lead may not
correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The green and yellow wire must be connected to the
terminal in the plug marked with the letter E or the earth
symbol
or coloured green or green and yellow.
The blue wire must be connected to the terminal marked
with the letter N or coloured black.
The brown wire must be connected to the terminal
marked with the letter L or coloured red.
Green and yellow : EARTH
Blue: NEUTRAL
Brown: LIVE
Loading...