DeLonghi DEDW60SI User Manual

De’Longhi Dishwasher

Model
DEDW60SI

© 2011 De’Longhi Australia Pty Ltd.

USER GUIDE

Please read this user guide carefully and retain for future reference

Contents Warranty Information

Parts and Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 03

De’Longhi Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . 04

Dishwasher Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . 05

Installation Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . 07

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 08

- Cabinet Preparation

- Aesthetic Fascia Panel Dimensions and Installation

- Tension Adjustment of the door

- Cold Water Connection

- Drain Hose Connection

- Positioning the Appliance

Using your Dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

- Before Starting the Dishwasher

- Prior to using for the first time

- Loading the Dishwasher Basket

- Starting a Washing Program

- Control Panel

- Turning on the Appliance

- Change the Program

- Forget to add a Dish?

- At the end of the Wash Cycle

The De’Longhi Dishwasher is warranted against faults
resulting from manufacturing or material defects. The
warranty period for normal domestic installation and use is
two years from the date of purchase. In non-domestic use
De’Longhi limits the voluntary warranty to 6 months.

De’Longhi undertakes to repair or replace the Dishwasher
at our discretion if the product is found to be defective due
to a manufacturing fault during the warranty period.

This warranty excludes any damage caused by misuse,
neglect, shipping accident, or incorrect installation.
Normal wear and tear is also expressly excluded. The
warranty claim is void if no fault is found with the product
or if work is carried out by anyone other than an authorised
De’Longhi Service Agent.

In Australia, this warranty is additional to the conditions
and guarantees which are mandatory as implied under the
Trade Practices Act 1974 and State and Territory
legislation.

How to contact us about a warranty claim

Talk to a De’Longhi representative for further warranty
or product information please call the number in your
country:

Australia

www.delonghi.com.au

Phone: [phone]

New Zealand

www.delonghi.co.nz

Phone: [phone]

Care and Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

- Filtering System

- Filter Assembly

- Cleaning the Filter

- Caring for the Dishwasher

- Protect against Freezing

- Cleaning the Spray Arms

- How to keep your Dishwasher in shape

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Help us Help You. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

NOTE: Warranty is determined by unit serial number and
date of purchase.

Page 2

Page 27

Help us Help You Parts and Features

Read this guide carefully, it is intended to help you
operate and maintain your new Dishwasher properly.

Keep it handy to answer your questions. If you don't
understand something or you need more assistance,
please call the De’Longhi Helpline.

Model: DEDW60SI

To help us provide prompt answers to your queries,
please record your Dishwasher model and serial
numbers. You’ll find them on a plate located on the
rear outside wall of the Dishwasher.

Dishwasher details

6

1

2

3

4

5

Components:

1. Upper Basket

2. Spray Arms 8. Coarse Filter

3. Lower Basket 9. Rinse Aid Dispenser

4. Main Filter 10. Drain Pipe Connector

5. Detergent Dispenser 11. Inlet Pipe Connector

6. Cup Shelf

7. Cutlery Basket

7

8

9

10 11

Before you call for service

Check the Troubleshooting Section on page 24. It lists
causes of minor operating problems that you can
correct yourself.

580

600

1135

850

Dimensions:

Height 850mm
Width 600mm
Depth 580mm

Voltage connected Load: see rating label
Water pressure: 0.04-1.0MPa
Hot water connection: max 60°C
Power supply: see rating label
Capacity: 12 place settings

Page 3Page 26

De’Longhi’s Safety Precautions Troubleshooting

De’Longhi pride themselves on their innovative range
of the highest quality consumer products.

De’Longhi ensures all of its products are 100% safe
through quality design and manufacture. All products
meet or exceed stringent laboratory-tested safety
requirements.

It is necessary for anyone using an electrical appliance
to be safety conscious. The following precautions are
essential for the safe use of an electrical appliance.
Carefully read all of the instructions provided with your
appliance:

Always turn the power off at the power outlet before

Ÿ

you insert or remove a plug. Remove by grasping
the plug, do not pull on the cord.

Do not use your appliance with an extension cord

Ÿ

unless this cord has been checked and tested by a
qualified technician or service person. The
extension cord must be a VDE-Listed, 3-wire
grounding extension cord that has a grounding
plug and outlet and that the electrical rating of the
cord is 220-240 volts and at least 10 amperes.

Always use your appliance from a power outlet of

Ÿ

the voltage (A.C. only) marked on the appliance.

Do not use an appliance for any purpose other than

Ÿ

its intended use.

Do not attempt to repair an electrical appliance.

Ÿ

Return a damaged or malfunctioning appliance to a
qualified service centre for adjustment or repair if
required.

The appliance must be positioned so the AC plug is

Ÿ

accessible.

This appliance is designed exclusively for

Ÿ

household use. All other uses are strictly forbidden.

The appliance is not intended for use by persons

Ÿ

(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.

If the power cable is damaged, it must be replaced

Ÿ

by the manufacturer, an authorised service centre
or a qualified electrician in order to eliminate all risk.

Problem Possible Causes Solution

The dishes
are not clean

Cloudiness
on glassware

Unsatisfactory washing result

Black or gray
marks on dishes

Detergent lef t in
dispenser cup s

The dishes are
not dr yi ng

Unsatisfactory

drying results

The dishes were not
loaded correctly.

The progr am w as
not powerful en ough.

Not enough dete rgent
was dispensed .

Items are b lo cking
the path of spray a rm s.

The filter comb ination
in t he base of wash
cabinet is not cl ea n or
is n ot correc tly fitted.
This may cause
the spray arm jet s
to g et blocked.

Combination o f soft
water and too muc h
detergent.

Aluminum uten sils have
rubbed agains t dishes.

Dishes block
detergent cup s.

Imprope r lo ading

Too li ttle rinse- ai d

Dishes are removed
too soon

Wrong p rogram
has been select ed

Use of cutlery wi th
a lo w-quality c oating

See notes in " Load in g the Dishwas he r Baskets ".

Select a more i ntensive program.
See" Wa sh Cycle Table ".

Use more de te rgent, or cha ng e your deterg en t.

Rearrange the i tems so that the sp ra y can rotat e freely.

Clean and/or fi t th e filter comb in ation correctly.
Clean the spray a rm j ets. See "Cle an ing the Spray
Arms".

Use less deterg ent if you have sof t wa ter and selec t
a sh ortest cycl e to w ash the glass wa re and to get
them clean.

Use a mild abrasi ve c leaner to eli mi nate those ma rk s.

Re-loading th e dishes prop erly.

Load the dishwa sher as suggest ed i n the direc tions.

Increas e th e amount of rin se -aid/re fill the rinse- aid
dispenser.

Do n ot empty your d is hwasher imm ed iately afte r
washing. Open t he d oor slightl y so t hat the steam c an
escape. Begin u nloading the di shwasher only o nce t
he d ishes are b arely war m to t he touch. Emp ty t he low
basket first. T his preve nt s water form dropping off
dishes in the upp er b asket.

In s hort prog ram the washi ng t emperature is lower.
This also lower s cl eaning perf ormance. Choo se
a program w it h a long washing ti me.

Water d rainage is more diffic ult with these it ems.
Cutlery or dish es o f this type are not suitable f or
washing in the di sh washer.

ERROR CODES

When some malfunctions occur, the appliance will display error codes to warn you:

Codes Meanings Possible Causes

E1 Longer inlet time. Faucets is not opened, or water intake is restricted, or water

pressure is too low.

E3 Longer heating time, but not Malfunction of temperature sensor or of heating element.

reaching required temperature.

E4 Overfilled. Too much inlet water.

E6 Failure of temperature sensor. Open circuit or break of temperature sensor.

E7 Failure of temperature sensor. Short circuit or break of temperature sensor.

WARNING!

If overflow occurs, turn off the main water supply before calling a service.

Ÿ

If there is water in the base pan because of an overfill or small leak, the water should be removed before restarting

Ÿ

the dishwasher.

Page 25Page 4

Troubleshooting

Before Calling for Service, review the following troubleshooting tips.

Problem Possible Causes Solution

Dishwas he r
doesn’t start

Fuse blown, or th e
circuit b reaker acte d

Replace fuse or reset circ uit break er. Remo ve any other
appliances sh aring the same ci rcuit with th e dishwasher

Dishwasher Safety Precautions

Wat er n ot pumped

Technical problems

from dishwa sher

Suds in the tub

Stained tub int er io r

White film on
inside surface

There are rust
stains on cutle ry

General problems

Knockin g noise
in the wash cab inet

Rattling nois e
in the wash cab inet

Noise

Knockin g noise
in the water pi pes

Power supply is n ot
turn ed on

Error cod e: E1;
Water p ressure is low

Door of dishwas he r
not prope rl y closed.

Kink in drain hos e

Filter clogge d

Kitchen sink cl og ged

Imprope r de tergent

Spilled rinse -aid

Detergent wit h
colourant was u se d

Hard wate r mi nerals

The affec te d items are
not corro si on resist ant.

A program w as n ot
run after dishw as her
salt was added. Traces
of s alt have gott en
into the wash cyc le .

The lid of the soft er
is l oose

A sp ray arm is
knocking agai nst
an i tem in a basket

Items of croc kery
are loose i n th e
wash cabinet

This may be cause d
by o n-site inst al lation
or t he cross- section
of t he piping.

Make sure t he d ishwasher is tu rn ed o n and the door is
closed securely.

Make sure t he p ower cord i s properly pl ugged into the
wall socket.

Check that the wa te r supply is conne cted prop erly and
the water is turned on.

Make sure t o cl ose the door properly and latc h it.

Check drain hos e.

Check coarse th e fi lter
(see section ti tled " Cleaning T he F ilter ")

Check the kitch en s ink to make sure it is drainin g we ll.
If t he proble m is the kitchen si nk n ot draining , yo u may
need a plumber ra th er than a service man for dishwas hers.

Use only the spec ia l dishwashe r de tergent to av oi d
suds. If this occ ur s, open the dishw asher and let sud s
evaporate. Ad d 1 ga llon of cold wate r to the tub. Close
and latch the dis hw asher, then Start the " so ak" wash
cycle to drain ou t th e water . Repeat if n ecessary.

Always wipe up ri ns e-aid spill s im mediately.

Make sure t ha t the detergent i s the one without
colourant.

To cle an the interior, use a damp s po nge with
dishwasher de tergent and wea r ru bber gloves .
Never use any oth er c leaner than d is hwasher
detergent for t he r isk of foamin g or s uds.

Always run the qu ic k wash prog ram .
without any crockery in the di shwasher and
without selec ting the Tur bo function ( if p resent) ,
after adding di sh washer salt .

Check the lip .En su re the fix is f in e.

Interrupt the p rogram, a nd rearrang e th e items
which are o bs tructing the sp ray arm.

Interrupt the p rogram,
and rearr an ge the items of crockery.

This has no influ en ce on the dishwas her function.
if i n doubt, cont ac t a suitably qual ified plumber.

Your safety and the safety of others is very important.
Safety messages are displayed in this manual and on
your appliance.

Read and obey these safety messages as they will alert
you to potential hazards and tell you how to reduce the
chance of injury.

DANGER

WARNING

CAUTION

Safety Alert Symbol

This symbol alerts you to potential hazards.

Danger

Danger indicates a high level of risk to yourself and others.
Ensure that care is taken to avoid severe injury or even
death.

Warning

Warning indicates a moderate level of risk to yourself, others
and the product. Ensure that care is taken to avoid extensive
product damage or serious injury.

Caution

Caution indicates a level of risk to yourself, others and the
product. Ensure care is taken to avoid moderate product
damage or injuries.

Page 5Page 24

Dishwasher Safety Precautions

Care and Cleaning

Before the appliance is used, it must
be properly positioned and installed
as described in this manual, so read
the manual carefully. To reduce the
risk of fire, electrical shock or injury
when using the appliance, follow
basic precaution, including the
following:

DANGER

Grounding Instructions

This appliance must be grounded. In the event of a

Ÿ

malfunction or breakdown, grounding will reduce
the risk of an electric shock by providing a path of
least resistance of electric current. This appliance is
equipped with a cord having an equipment­grounding conductor and a grounding plug. The
plug must be plugged into an appropriate outlet
that is installed and grounded in accordance with all
local codes and ordinances.

Improper connection of the equipment-grounding

Ÿ

conductor can result in the risk of an electric shock.

Check with a qualified electrician or service

Ÿ

representative if you are in doubt whether the
appliance is properly grounded. Do not modify the
plug provided with the appliance; If it does not fit
the outlet. Have a proper outlet installed by a
qualified electrician.

WARNING

Do not abuse, sit on, or stand on the door or dish

Ÿ

rack of the dishwasher.

Do not touch the heating element during or

Ÿ

immediately after use. (This instruction is only
applicable to machines with a visual heating
element.)

Do not operate your dishwasher unless all

Ÿ

enclosure panels are properly in place. Open the
door very carefully if the dishwasher is operating,
there is a risk of water squirting out.

Do not place any heavy objects on or stand on the

Ÿ

door when it is open. The appliance could tip
forward.

When loading items to be washed:

Ÿ

1. Locate sharp items so that they are not likely to
damage the door seal;

2. Warning: Knives and other utensils with sharp
points must be loaded in the basket with their
points down or placed in a horizontal position.

Check that the detergent compartment is empty

Ÿ

after completion of the wash cycle.

WARNING

When using your dishwasher, you should prevent

Ÿ

plastic items from coming into contact with the
heating element.(This instruction is only applicable
to machines with a visual heating element.)

Do not wash plastic items unless they are marked

Ÿ

dishwasher safe or the equivalent. For plastic items
not so marked, check the manufacturer's
recommendations.

Use only detergent and rinse additives designed for

Ÿ

an automatic dishwasher.

Never use soap, laundry detergent, or hand

Ÿ

washing detergent in your dishwasher. Keep these
products out of the reach of children.

Keep children away from detergent and rinse aid,

Ÿ

keep children away from the open door of the
dishwasher, there could still be some detergent left
inside.

This appliance is not intended for use by persons

Ÿ

(including children )with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.

Children should be supervised to ensure that they

Ÿ

do not play with the appliance.

Dishwasher detergents are strongly alkaline, they

Ÿ

can be extremely dangerous if swallowed. Avoid
contact with skin and eyes and keep children away
from the dishwasher when the door is open.

The door should not be left open, since this could

Ÿ

increase the risk of tripping.

If the supply cord is damaged, it must be replaced

Ÿ

by the manufacturer or its service agent or a
similarly qualified person in order to avoid a hazard.

Remove the door to the washing compartment

Ÿ

when removing an old dishwasher from service or
discarding it.

Please dispose of packing materials properly.

Ÿ

Use the dishwasher only for its intended function.

Ÿ

During installation, the power supply must not be

Ÿ

excessively or dangerously bent or flattened.

Do not tamper with controls.

Ÿ

The appliance is to be connected to the water

Ÿ

mains using new hose sets and that old hose-sets
should not be reused.

The maximum number of place settings to be

Ÿ

washed is 12.

The maximum permissible inlet water pressure is

Ÿ

1Mpa.

The minimum permissible inlet water pressure is

Ÿ

0.04Mpa.

Protect against Freezing

Please take frost protection measures on the
dishwasher in winter. After washing cycles, please
operate as follows:

1. Cut off the electrical power to the dishwasher.

2. Turn off the water supply and disconnect the water
inlet pipe from the water valve.

3. Drain the water from the inlet pipe and water valve.
(Use a pan to catch the water)

4. Reconnect the water inlet pipe to the water valve.

5. Remove the filter at the bottom of the tub and use a
sponge to soak up water in the sump.

NOTE: If your dishwasher cannot work because of
the ice, please contact professional service persons.

Cleaning the Spray Arms

It is necessary to clean the spray arms regularly for
hard water chemicals will clog the spray arm jets and
bearings.

To remove the upper spray arm, screw off the nut
clockwise then remove the arm.

To remove the lower spray arm, pull out the spray arm
upward.

Wash the arms in soapy and warm water and use a
soft brush to clean the jets. Replace them after rinsing
them thoroughly.

UNSCREW

PULL OUT

How to keep your Dishwasher in shape

After every wash, turn off the water supply to the

Ÿ

appliance and leave the door slightly open so that
moisture and odours are not trapped inside.

Before cleaning or performing maintenance,

Ÿ

always remove the electrical plug from the socket.

To clean the exterior and rubber parts of the

Ÿ

dishwasher, do not use solvents or abrasive
cleaning products. Only use a cloth with warm
soapy water.

To remove spots or stains from the surface of the

Ÿ

interior, use a cloth dampened with water an a little
vinegar, or a cleaning product made specifically for
dishwashers.

When not in Use for a long time

It is recommend that you run a wash cycle with the
dishwasher empty and then remove the plug from the
socket, turn off the water supply and leave the door of
the appliance slightly open. This will help the door
seals to last longer and prevent odours from forming
within the appliance.

Moving the Appliance

If the appliance must be moved, try to keep it in the
vertical position. If absolutely necessary, it can be
positioned on its back.

Seals

One of the factors that cause odours to form in the
dishwasher is food that remains trapped in the seals.
Periodic cleaning with a damp sponge will prevent
this from occurring.

Page 23Page 6

Installation Safety PrecautionsCare and Cleaning

STEP 3: Lift the Fine Filter up.

3

NOTES:

When following this procedure from step 1 to step

Ÿ

3, the filter system will be removed; when following
it from Step 3 to Step 1, the filter system will be
installed.

Inspect the filters for blocking after every time the

Ÿ

dishwasher has been used.

By unscrewing the coarse filter, you can remove the

Ÿ

filter system. Remove any food remnants and clean
the filters under running water.

The entire filter assembly should be cleaned once a

Ÿ

week.

Cleaning the Filter

To clean the coarse filter and the fine filter, use a
cleaning brush. Reassemble the filter parts as shown
in the figures on the last page and reinsert the entire
assembly in the dishwasher, positioning it in its seat
and pressing downwards.

Caring for the Dishwasher

The control panel can be cleaned by using a lightly
dampened cloth. After cleaning, make sure to dry it
thoroughly.

For the exterior, use a good appliance polish wax.

Never use sharp objects, scouring pads or harsh
cleaners on any part of the dishwasher.

Cleaning the Door

To clean the edge around the door, you should use
only a soft warm, damp cloth.

To avoid penetration of water into the door lock and
electrical components, do not use a spray cleaner of
any kind.

WARNING!

Never use a spray cleaner to clean the door panel

Ÿ

as it may damage the door lock and electrical
components.

Abrasive agents or some paper towels should not

Ÿ

be used because of the risk of scratching or leaving
spots on the stainless steel surface.

Electrical Connection

This appliance should be properly grounded for

Ÿ

your safety. The power cord of this appliance is
equipped with a three-prong plug which mates
with standard three prong wall outlets to minimise
the possibility of electrical shock.

DO NOT UNDER ANY CIRCUMSTANCES CUT

Ÿ

OR REMOVE THE EARTHING CONNECTION
FROM THE POWER CORD SUPPLIED. FOR
PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED.

Please look at the rating label to know the rating

Ÿ

voltage and connect the dishwasher to the
appropriate power supply. Use the required fuse
10 amp, time delay fuse or circuit breaker
recommended and provide separate circuit
serving only this appliance.

Ensure the voltage and frequency of the power

Ÿ

being used corresponds to those on the rating
plate. Only insert the plug into an electrical socket
which is earthed properly. If the electrical socket to
which the appliance must be connected is not
appropriate for the plug , replace the socket, rather
than using a adaptors or the like as they could
cause overheating and burns.

The cord should be secured behind the appliance

Ÿ

and not left exposed or dangling to prevent
accidental injury.

The appliance should always be plugged into its

Ÿ

own individual electrical outlet which has a voltage
rating that matches the rating label on the
appliance. This provides the best performance and
also prevent overloading house wiring circuits that
could cause a fire hazard from overheated. Never
unplug the appliance by pulling the power cord.
Always grip the plug firmly and pull straight out
from the receptacle. Repair or replace immediately
all power cords that have become frayed or
otherwise damaged. Do not use a cord that shows
cracks or abrasion damage along its length or at
either end. When moving the appliance, be careful
not to damage the power cord.

Extension Cord

WARNING: DO NOT USE AN EXTENSION CORD

Ÿ

OR AN ADAPTER PLUG WITH THIS APPLIANCE.

Grounding Instructions

This appliance must be earthed. In the event of a

Ÿ

malfunction or breakdown, earthing will reduce the
risk of electric shock by providing a path of least
resistance for the electric current. This appliance
is equipped with a cord having an equipment­earthing conductor and an earthing plug. The plug
must be plugged into an appropriate outlet that is
installed and earthed in accordance with all local
standards and requirements.

WARNING

Improper connection of the equipment earthing

Ÿ

conductor can result in the risk of an electric shock.
Check with a qualified electrician or service

Ÿ

representative if you are in doubt whether the
appliance is properly earthed.

Do not modify the plug provided with the

Ÿ

appliance. If the plug does not fit properly to the
outlet, please have a qualified electrician to install a
proper outlet.

Page 7Page 22

Installation

90° 90°

820mm

580mm

80

100

600mm

Electrical, drain

and water supply

line entrances

Space between cabinet

bottom and floor

Care and Cleaning

Cabinet Preparation

Choose a place near the sink to facilitate the

Ÿ

installation of inlet and drain hoses.
Cabinet dimensions less than 5mm between the

Ÿ

top of dishwasher and cabinet and the outer door
aligned to cabinet.

Minimum space between the door and adjacent

Ÿ

cabinet when the door is opened is 50mm.

Aesthetic Fascia Panel Dimensions and
installation

The aesthetic fascia panel should be processed

Ÿ

according to the diagram below.

568

46.5

10-Ø2

370

MAX 587

38

30

254 250

592

Front View

Filtering System

The filter prevents larger remnants of food or other
objects from getting inside the pump.

The residue may block the filter, in this case they must
be removed.

The filter system consists of a coarse filter, a flat (Main
filter) and a microfilter (Fine filter).

MAIN FILTER: Food and soil particles trapped

1

in this filter are pulverized by a special jet on the
lower spray arm and washed down the drain.

COARSE FILTER: Larger items, such as

2

pieces of bones or glass, that could clog the
drain are trapped in the coarse filter. To remove
an item caught in this filter, gently squeeze the
taps on the top of this filter and lift it out.

FINE FILTER: This filter holds soil and food

3

residues in the sump area and prevents it from
being redeposit on the dishes during a cycle.

2

Filter Assembly

The filter efficiently removes food particles from the
wash water, allowing it to be recycled during the cycle.

For best performance and results, the filter must be
cleaned regularly. For this reason, it is a good idea to
remove the larger food particles trapped in the filter
after each wash cycle by rinsing the semicircular filter
and cup under running water.

To remove the filter device, pull the cup handle in the
upward direction.

WARNING!

The dishwasher must never be used without the

Ÿ

filters.

Improper replacement of the filter may reduce the

Ÿ

performance level of the appliance and damage
dishes and utensils.

STEP 1: Turn the filter in anti-clockwise direction, then
lift it up.

Open

1

Dishwasher

Dishwasher

Door

Min. space

of 50mm

Cabinet

Ø2

Side View

10~17

5~12

1

3

STEP 2: Lift the Main Filter up.

2

Page 8

Page 21

Using Your Dishwasher

Installation

NOTE:

If you open the door during a wash cycle, the machine
will pause. The LED Display Window will stop blinking
and the buzzer will sound every minute unless you
close the door. After you close the door, the
dishwasher will continue working after 10 seconds.

If display window shows error codes after a warning
sound (see page 25 for “ERROR CODES"), that
indicates the machine is out of order, please turn off
the main power and water supply before calling for
service.

FORGET TO ADD A DISH?

A forgotten dish can be added at any time before the
detergent cup opens.

1. Open the door a little to stop the washing.

2. After the spray arms stop working, you can open
the door completely.

3. Load the forgotten dishes.

4. Close the door, the dishwasher will start running
again after 10 seconds.

WARNING! It is dangerous to open the door when
washing, because the hot water may scald you.

AT THE END OF THE WASH CYCLE

When the working cycle has finished, the buzzer of the
dishwasher will sound for 8 seconds, then stop. Turn
off the appliance using the ON/OFF button, shut off
the water supply and open the door of the dishwasher.
Wait for a few minutes before unloading the
dishwasher to avoid handling the dishes and utensils
while they are still hot and more susceptible to
breakage. They will also dry better.

Switch off the Dishwasher

When the digital display shows ‘-:--’ (remaining
program time), the program has ended.

1. Switch off the dishwasher by pressing the ON/OFF
button.

2. Turn off the water tap!

Open the door carefully

The dishes should be allowed to cool down around 15
minutes before removing from the appliance.

Open the dishwasher's door, leave it ajar and wait a
few minutes before removing the dishes. Dishes will
be cooler and the drying will be improved.

Unloading the Dishwasher

It is normal that the dishwasher is wet inside.

Empty the lower basket first and then the upper one.
This will avoid water dripping from the upper Basket
onto the dishes in the lower one.

Install the hook on the aesthetic fascia panel and

Ÿ

put the hook into the slot of the outer door of
dishwasher (see below).

Outer Door

The hook is lifted from position 1 to the appropriate place,
then pushed right to position 2, making the panel and the
outer door align.

2

1

After positioning of the panel, fix the panel onto the

Ÿ

outer door by screws and bolts (See following
diagrams).

2

1

ST4 screw

Cover

Spacer for aesthetic panel

ST4 screw

Hook for aesthetic panel

Outer door of
dishwasher

Tension adjustment of the door

The door springs are set at the factory to the

Ÿ

proper tension for the outer door. If an aesthetic
fascia panel is installed, you will have to adjust the
door spring tension. Rotate the adjusting screw to
drive the adjustor to strain or relax the steel cable
(see below).

Adjust the door spring tension until the door

Ÿ

remains balanced in the fully-opened position.

Aesthetic panel

Page 20

A A

B B

Hook for
aesthetic
panel

relax

Page 9

Installation Using Your Dishwasher

Cold Water Connection

Connect the cold water supply hose to a threaded

Ÿ

3/4(inch) connector and make sure that it is
fastened tightly in place.

If the water pipes are new or have not been used for

Ÿ

an extended period of time, let the water run to
make sure that the water is clear. This precaution is
needed to avoid the risk of the water inlet getting
blocked and damaging the appliance.

WARNING!
In order to avoid water staying in the inlet hose,
please close the hydrant after using. (Not applicable
to appliances without aqua-stop.)

Drain Hose Connection

Insert the drain hose into a drain pipe with a

Ÿ

minimum diameter of 4cm, or let it run into the sink,
making sure to avoid bending or crimping it. Use
the special plastic support that comes with the
appliance . The top of the hose must be at a height
between 40 and 100cm. The free end of the hose
must not be immersed in water to avoid the back
flow of it.

SINK

DISHWASHER

Min 400 mm

Min 100 mm

Inlet pipe
connector

FRONT VIEW

Drain pipe
connector

POWER
OUTLET

Positioning the Appliance

Position the appliance in the desired location. The

Ÿ

back should rest against the wall behind it, and the
sides, along the adjacent cabinets or walls. The
dishwasher is equipped with water supply and
drain hoses that can be positioned either to the
right or the left sides to facilitate proper installation.

Put the dishwasher on the slide rails supplied.

Ÿ

Affix the condensation strip under the cabinet

Ÿ

bench top. Ensure the condensation strip is flush
with the edge.

Water Outlet

Connect the water drain hose. The drain hose must

Ÿ

be correctly fitted to avoid water leaks. Ensure that
the water drain hose is not kinked or squashed.

Extension Hose

If you need a drain hose extension, make sure to

Ÿ

use a similar drain hose.
It must be no longer than 4 metres; otherwise the

Ÿ

cleaning effect of the dishwasher could be
reduced.

Syphon Connection

The waste connection must be at a height of

Ÿ

between 40 cm (minimum) and 100 cm (maximum)
from the bottom of the dish. The water drain hose
should be fixed by a hose clip. The free end of the
hose must not be immersed in water.

WARNING!

Max 100 0mm

DO NOT BEND IN ANY WAY!

CONTROL PANEL

Delay 1/

2

6 57 4 3 2 1

Power indicator light: To show the power

1

supply.

Power switch: To turn on/off the power supply.

2

Start/Pause button: To start the selected

3

washing program or pause the washing
program when the machine is working.

Program Button: To select your desired

4

program from the seven washing programs.

TURNING ON THE APPLIANCE

Starting a wash cycle:

1. Draw out the lower and upper basket, load the
dishes and push them back. It is recommended to
load the lower basket first, then the upper one (see
the section entitled “Loading the Dishwasher”).

2. Pour in the detergent (see Page 13).

3. Insert the plug into the socket. The power supply is
220-240 VAC /50 HZ, the specification of the
socket is 10A 250VAC. Make sure that the water
supply is turned on to full pressure.

4. Close the door, press the ON/OFF button, and the
ON/OFF light will turn on.

5. Press the program button to select your desired
program, then press the Start/Pause button, the
dishwasher begins to start.

NOTE: When you press the Start/Pause button to
pause during washing, the LED Display Window will
stop blinking and the dishwasher will moo every
minute unless you press the Start/Pause button to
start.

Prog. Start/Pause

Half load functions Button: To select Half load

5

On/ Off

functions. (Half load function means that the
lower spray arm does not run, so you should
load the upper basket only).

Delay Button: To Press the button to delay.

6

Display window: Display the program, program

7

remaining time, delay time, fault codes and etc.

CHANGE THE PROGRAM

Premise:

1. A cycle that is underway can only be modified if it
has only been running for a short time. Otherwise,
the detergent may have already been released, and
the appliance may have already drained the wash
water.

If this is the case, the detergent dispenser must be

refilled (see the section entitled "Adding
Detergent").

2. Press the Start/Pause button, then press the
program button more than 3 seconds , the machine
will be in standby mode, then you can change the
program to the desired cycle setting (see the
section entitled " Starting a wash cycle. . .").

NOTE: During delay mode, press the Start/Pause
button, then you can change the program and
delay time.

3. The LED display shows the state of the dishwasher:

a) LED shows '-:--' -- Stand by

b) LED shows 'H:MM' and not blinking--Being paused

c) LED shows 'H:MM' and blinking--Running

Page 19Page 10

Using Your Dishwasher

Rubber Cover

Screw

Installation

STARTING A WASHING PROGRAM

Wash Cycle Table

NOTE: Star ( ) means the need to fill rinse into the Rinse Aid Dispenser.

Program

Cycle Selection

Information

Description

of Cycle

Detergent

pre/main

(Hrs/Mins)

Pre-w ash（50°C）
wash（50°C）
rinse（70° C）
drying

Pre-w ash(50° C)
Pre-w ash
Was h (65°C)
Rinse
Rinse
Rinse (55 °C)
Drying

Pre-w ash(50° C)
Was h (50°C)
Rinse
Rinse (65 °C)
Drying

Was h (55°C)
Rinse
Rinse
Rinse (52 )
Drying

Was h (40°C)
Rinse
Rinse (70 °C)
Drying

Was h (40°C)
Rinse
Rinse (45 °C)

Pre-w ash

°C

3in1

5/25g

5/25g

5/25g

/

20g.

/

3-in-1

Intensive

Heavy

Normal

(AS/NZ S 200 7. 1 )

Rinse

Rapid

Soak

For norma lly soile d loads,
such as pot s, plates ,glasses
and light ly soiled p ans.
standard daily c ycle.

For the hea viest soi led loads,
such as pot s,pans, casserole
dishes an d dishes th at have
been sitt ing with dr ied food
on them for a w hile.

For heavy s oiled loa ds,
such as pot s, plates ,
glasses a nd lightl y soiled
pans. sta ndard d aily cycl e.

For norma l soiled lo ads,
such as pla tes, glas ses,
bowls and l ightly so iled
pans.

For dishe s that need t o be
rinsed an d dried onl y.

A shorter w ash for lig htly
soiled lo ads that do n ot
need dryi ng.

To rinse dish es that you
plan to was h later tha t day.

Running

time

2:30

1:10

1:30

1:05 0.87 11.8

1:20

30

8

Energy

(Kwh)

1.2

1.4

1.2

0.8

0.45

0.01

Water

(L)

12

22

16

8

12

4

Rinse

Aid

Aquasafe Connection

The Aquasafe System is a safety valve system,

Ÿ

preventing you from water leaks. If the water inlet
hose starts to leak during a wash cycle, the safety
valve cuts off the running water. Do not immerse
the water inlet hose or the safety valve in water,
because the electrical cable for the safety valve is in
the double-walled water inlet hose.

If water inlet hose or the safety valve is damaged,

Ÿ

remove the main plug immediately.

Do not enlarge or shorten the inlet hose because it

Ÿ

contains electric parts.

Levelling the Dishwasher

Once the appliance is positioned for levelling, the

Ÿ

height of the dishwasher may be altered via
adjustment of the screwing level of the feet. In any
case, the appliance should not be inclined more
than 2 °.

The rear feet can be adjusted from the front of the

Ÿ

dishwasher by turning the screws on the left and
right hand side of the cabinet. To adjust the front
feet, use a wrench and turn the front feet until the
dishwasher is level.

Place level on door and rack track inside the tub as

Ÿ

shown to check that the dishwasher is level.

Check level
Front to Back.

Check level side to side.

Securing the Dishwasher

The dishwasher must be secured in place using either
of the following methods:

Normal work surface - secure to the work surface

Ÿ

by using two woodscrews e nsuring the
dishwasher weight is not being hit by the surface.

Marble or granite work top - secure the bracket to

Ÿ

the side panel of the dishwasher and secure the
dishwasher to the furniture housing. Put the rubber
cap over the screw.

NOTE:

* AS/NZS 2007.1: This program is the test cycle.

The information for comparability test in accordance with AS/NZS 2007.1, as follows:

Capacity: 12 setting

Ÿ

Position Upper basket: In position 1 (Page 15)

Ÿ

Rinse aid setting: 3

Ÿ

Open the door slightly 50mm to assist in drying of the dishes after every wash

Ÿ

Page 11Page 18

Using Your Dishwasher

Using Your Dishwasher

BEFORE STARTING THE DISHWASHER

The following things should be checked before
starting the dishwasher.

1. That the dishwasher is level and fixed properly.

2. That the inlet valve is open .

3. That there is no leakage at the connections of the
conducts.

4. The wires are tightly connected and the power is
switched on.

5. That the inlet and drain hoses are not knotted or
kinked.

6. All packing materials should be taken out of the
dishwasher.

PRIOR TO USING FOR THE FIRST TIME

Before using your dishwasher for the first time:

Fill the Rinse Aid Dispenser

The rinse aid is released during the final rinse to
prevent water from forming droplets on your dishes,
which can leave spots and streaks. It also improves
drying by allowing water to roll off the dishes. Your
dishwasher is designed to use liquid rinse aids. The
rinse aid dispenser is located inside the door next to
the detergent dispenser. To fill the dispenser, open the
cap and pour the rinse aid into the dispenser until the
level indicator turns completely black. The volume of
the rinse aid container is about 140ml.

Function of the Rinse Aid

Rinse aid is automatically added during the last rinse,
ensuring thorough rinsing, and spot and streak free
drying.

WARNING!

Only use branded rinse aid for dishwasher. Never fill
the rinse aid dispenser with any other substances
(e.g. Dishwasher cleaning agent, liquid detergent).
This would damage the appliance.

When to refill the Rinse Aid Dispenser

If there is no rinse-aid warning light in the control
panel, you can judge the amount of rinse-aid by the
color of the optical level indicator "C" located next to
the cap. When the rinse-aid container is full, the whole
indicator will be dark. As the rinse-aid diminishes, the
size of the dark dot decreases. You should never let
the rinse aid get below 1/4 full.

As the rinse aid diminishes, the size of the black dot
on the rinse aid level indicator changes, as illustrated
below.

Full

C (Rinse-Aid indicator)

3/4 Full

1/2 Full

1/4 Full

(Should refill to
eliminate spotting)

MIN

MA

X

Empty

How to fill the Rinse Aid Dispenser

1. To open the dispenser, turn the cap to the "open"
(left) arrow and lift it out.

2. Pour the rinse aid into the dispenser, being careful
not to overfill.

3. Replace the cap by inserting it aligned with "open"
arrow and turning it to the closed (right) arrow.

1 2

3

Be careful not to overfill the dispenser, because this
could cause over sudsing. Wipe away any spills with a
damp cloth. Don't forget to replace the cap before you
close dishwasher door.

ATTENTION! Clean up any rinse aid split during filling
with an absorbent cloth to avoid excess foaming
during the next wash.

WARNING!

Do not let any item extend

Ÿ

through the bottom.

Always load sharp utensils with

Ÿ

the sharp point down!

Suitability of items for use in your Dishwasher

NOT SUITABLE FOR USE

Cutlery with wooden, horn china or m o t h e r - o f -

Ÿ

pearl handles.

Plastic items that are not heat resistant.

Ÿ

Older cutlery with glued parts that are not

Ÿ

temperature resistant.

Bonded cutlery items or dishes.

Ÿ

Pewter or copper items.

Ÿ

Crystal glass.

Ÿ

Steel items subject to rusting.

Ÿ

Wooden platters.

Ÿ

Items made from synthetic fibres.

Ÿ

LIMITED SUITABILITY

Some types of glasses can become dull after a

Ÿ

large number of washes.

Silver and aluminum parts have a tendency to

Ÿ

discolour during washing.

Glazed patterns may fade if machine washed

Ÿ

frequently.

NOTE:

Do not put in items that are dirty with cigarette ash,

Ÿ

candle wax, lacquer or paint.

If you buy new dishes please make sure that they

Ÿ

are suitable for dishwashers.

Please do not overload your dishwasher. Do not

Ÿ

use dishes that are not suitable for dishwashers.
This is important for good results and for
reasonable energy consumption.

Before loading the dishes, you should:

Remove large food particles.

Ÿ

Soften remnants of burnt food in pans.

Ÿ

When loading the dishes and cutlery, please note:

Dishes and cutlery must not impede the rotation of

Ÿ

the spray arms.

Load hollow items such as cups, glasses, pans etc.

Ÿ

with the opening downwards so that water cannot
collect in the container or a deep base.

Dishes and items of cutlery must not lie inside one

Ÿ

another, or cover each other.

To avoid damage to glasses, they must not touch.

Ÿ

Load large items which are most difficult to clean

Ÿ

into the lower rack.

The upper rack is designed to hold more delicate

Ÿ

and lighter dishware such as glasses, coffee and
tea cups.

ATTENTION!

Long bladed knives stored in an upright position are

Ÿ

a potential hazard!

Long and/or sharp items of cutlery such as carving

Ÿ

knives must be positioned horizontally in the upper
basket.

Damage to glassware and other dishes

Possible Causes

Type of glass or manufacturing process. Chemical

Ÿ

composition of detergent.

Water temperature and duration of dishwasher

Ÿ

program.

Suggested remedy:

Use glassware or porcelain dishes that have been

Ÿ

marked dishwasher-proof by the manufacturer

Use a mild detergent that is described as kind of

Ÿ

dishes If necessary, seek further information from
detergent manufacturers.

Select a program with as low a temperature.

Ÿ

To prevent damage, take glass and cutlery out of

Ÿ

the dishwasher as soon as possible after the
program has ended. as possible after the program
has ended.

Page 12 Page 17

Using Your Dishwasher

Using Your Dishwasher

NOTE: The upper rack has side flaps (pictured at left
above basket). There are 4 (2 on each side). These
can be adjusted into 2 positions = position 1 (high)
and position 2 (low).

To move the flaps between these positions, locate the
large hinges clip each flap to the upper rack. There are
two of these at either end of each flap. Gently pull
both clips off the wire rack and move the flap to the
desired position.

Position 1

The upper position will accommodate items such as
glass tumblers (placed beneath flap) and wine
glasses. Wine glasses can be placed upside down so
that the neck rests in the grooves at side of flap with
the base of the glass facing upward.

Position 2

When the flaps are moved to the lower position, they
can be used to hold additional tumblers, cups and
mugs. Always check that you are only placing items
on the flaps that will clear the ceiling height of your
dishwasher when you push the rack back in. Be
particularly careful with long-stemmed glassware
such as champagne glasses breakage hazard!

Loading the Lower Basket

We recommend that you place large items which are
most difficult to clean into the lower basket: pots,
pans, lids, serving dishes and bowls, as shown in the
figure below.

It is preferable to place serving dishes and lids on the
side of the racks in order to avoid blocking the rotation
of the top spray arm.

Pots, serving bowls, etc. must always be placed

Ÿ

top down.
Deep pots should be slanted to allow water to flow

Ÿ

out.
The bottom basket feature fold down tine rows so

Ÿ

that larger or more pots and pans can be loaded.

5

6

IN

3 - Saucers

4 - Dessert dishes

5 - Dinner plates

6 - Soup plates

7 - Cutlery basket

Folding spikes

For better stacking of pots and pans, the spikes can
be folded down as show in the picture below.

Cutlery Basket

Cutlery should be placed in the cutlery basket with the
handles at the bottom. If the rack has side baskets, the
spoons should be loaded separately into the appropriate
slots, especially long utensils should be placed in the
horizontal position at the front of the upper basket as shown
in the picture.

2

3

1
1
1

1
1
1

1
1
1

1
1

1

3

5
5
5

5
5
5

5
5
5

5
5
5

2

3

2

3

3

2

3

2

3

3

2

2

3

3

2
2

3

3

2
2
2

1

4
4
4

4
4
4

4
4

4

4
4

4

Forks

Soup spoons2

Adjusting the Rinse Aid Dispenser

The rinse aid dispenser has four scales. Always start
with the dispenser set on "3". If spots and poor drying
are a problem, increase the amount of rinse aid
dispensed by removing the dispenser lid and rotating
the dial to "4". The recommended setting is "3".
(Factory value is "3".)

NOTE: Increase the dose if there are drops of water or
lime spots on the dishes after washing. Reduce it if
there are sticky whitish stains on your dishes or a
bluish film on glassware or knife blades.

Adjust lever
(Rinse)

Detergents

There are 3 sorts of detergents:

1. With phosphate and with chlorine

2. With phosphate and without chlorine

3. Without phosphate and without chlorine

Normally new pulverised detergent is without
phosphate. Thus the water softener function of
phosphate is not given. In this case we recommend to
fill salt in the salt container even when the hardness of
water is only 6 °dH. If detergents without phosphate
are used in the case of hard water often white spots
appear on dishes and glasses. In this case please add
more detergent to reach better results. Detergents
without chlorine do only bleach a little. Strong and
coloured spots will not be removed completely. In this
case please choose a program with a higher
temperature.

Concentrated Detergent

Based on their chemical composition, detergents can
be split in two basic types:

Conventional, alkaline detergents with caustic

Ÿ

components
Low alkaline concentrated detergents with natural

Ÿ

enzymes

concentrated detergents are used can achieve the
same results that can otherwise only be achieved
using “intensive” programs.

Detergent Tablets

Detergent tablets of different brands dissolve at
different speeds. For this reason some detergent
tablets cannot dissolve and develop their full cleaning
power during short programs. Therefore please use
long programs when using detergent tablets, to
ensure the complete removal of detergent residuals.

Detergent Dispenser

The dispenser must be refilled before the start of each
wash cycle following the instructions provided in the
wash cycle table. Your dishwasher uses less
detergent and rinse aid t han Conventional
dishwasher. Generally, only one tablespoon of
detergent is needed for a normal wash load. More
heavily soiled items need more detergent. Always add
the detergent just before starting the dishwasher,
otherwise it could get damp and will not dissolve
properly.

Adding detergent to Dishwasher

If the lid is closed: press release button. The lid will

Ÿ

spring open.
Always add the detergent just before starting each

Ÿ

wash cycle.
Only use branded detergent aid for dishwasher.

Ÿ

1

Push latc h to open

2

5 7 4

4

3

3 Dessert spoons

Teaspoons4

5

Knives

The use of“normal” washing programs in combination
with concentrated detergents reduces pollution and is
good for your dishes; these wash programs are
specifically matched to the dirt-dissolving properties
of the enzymes of the concentrated detergent. For this
reason “normal”wash programs in which

Page 13Page 16

Using Your Dishwasher

Using Your Dishwasher

WARNING! Dishwasher detergent is poisonous! Take
care to keep it out of reach of children.

Proper Use of Detergent

Only use detergent specifically made for the use in

Ÿ

dishwashers. Keep your detergent fresh and dry.
Don't put powdered detergent into the dispenser

Ÿ

until you're ready to wash dishes.

Fill the detergent dispenser with detergent. The
marking indicates the dosing levels, as shown below:

Location of main wash cycle detergent.

A

Location of pre-wash cycle detergent.

B

A

B

Please observe the manufacturers dosing and
storage recommendations as stated on the detergent
packaging.

Close the lid and press until it locks in place.

If the dishes are heavily soiled, place an additional
detergent dose in the pre-wash detergent chamber.
This detergent will take effect during the pre-wash
phase.

NOTE: See information about the amount of
detergent for the single programs on page 18. Please
be aware, that according to the level soiling and the
specific hardness of water differences are possible.

P l e a s e o b s e r v e t h e m a n u f a c t u r e r ' s
recommendations on the detergent packaging.

Use of “2-in-1”, 3-in-1”, “4-in-1” and “5-in-1”
Combination / Compact Detergents.

These products are detergents with integrated and
combined detergent/rinse aid and salt functions.
Before using these products you should first check
that the water hardness in your supply is compatible
with the use of these products as per the detergent
manufacturers (on the product packaging).

These products should be strictly used according to
the detergent manufacturer's instructions. In general
detergents that include rinse aid or water softener are
only able to serve good results under certain
conditions: rinse aid and water softener can not
adapted to specific conditions. For this reasons in
some cases there might be unwanted cleaning or
drying results.

Please ask the detergent manufacturer to inform you
about the best consume conditions. If you encounter
problems when using these products for the first time
then please contact the detergent manufacturers care
line. The manufacturer of your dishwasher is not liable
for damages caused by compact detergents nor gives
warranty if you use compact detergents.

NOTE: When using “2-in-1”,“3-in-1”,“4-in-1” or “5­in-1” Combination / Compact Detergents, please pay
attention to make sure that the size of the
Combination Detergents is fitted to the dispenser so
that Combination Detergents can be easy to put in the
dispenser and dispenser would not be broken.

ATTENTION! Keep all detergents in a safe place out
of children's reach.

Always add the detergent in the dispenser just before
starting the dishwasher.

How to use the 3-in-1 Program

Your dishwasher has a 3-in-1 program which needs
no salt and rinse aid but a 3-in-1 tablet. This
dishwasher comes with a 3-in-1 tablet container as an
accessory.

NOTE: Only the 3-in-1 program can be used with 3­in-1 tablets. If you use 3-in-1 tablets in other
programs, the appliance will not achieve a good
performance.

1. The figure below shows how to hang the 3-in-1

tablet container on the upper basket.

2. Rotate the upper spray arm and change the
location of the container to ensure the upper spray
arm is not obstructed by the 3-in-1 tablet container.
Refer to the figure below for reference.

3. Put the 3-in-1 tablet into the container, then start
the 3-in-1 program.

NOTE:

When using 3-in-1 combination / compact
Detergents, please pay attention to make sure that the
size of the combination detergents fits to the
dispenser so that combination detergents can be
easily put into the dispenser, and the dispenser would
not be broken.

LOADING THE DISHWASHER BASKET

For best performance of the dishwasher, follow these
loading guidelines. Features and appearance of
baskets and cutlery baskets may vary from your
model.

Attention before or after Loading the Dishwasher
Baskets.

Scrape off any large food particles. Soften remnants of
burnt food in pans.

It is not necessary to rinse the dishes under running
water. Place objects in the dishwasher in following
way:

1. Items such as cups, glasses, pots/pans, etc. are
faced downwards.

2. Curved items, or ones with recesses, should be
loaded aslant so that water can run off.

3. All utensils are stacked securely and can not tip
over.

4. All utensils are placed in the way that the spray
arms can rotate freely during washing.

Very small items should not be washed in the
dishwasher as they could easily fall out of the baskets.

Loading the Upper Basket

The upper basket is designed to hold more delicate
and lighter dishware such as glasses, coffee and tea
cup and saucers, as well as plates, small bowls and
shallow pans (as long as they are not too dirty).

Position the dishes and cookware so that they do not
get moved by the spray of water.

11

2

1

IN

3

2

2

2

1

1 - Cups 2 - Glasses 3 - Saucers

NOTE: The upper basket is adjusted in the position 1.

Adjusting the Upper Basket

Your dishwasher comes with an adjustable top rack
(basket) illustrated below. Its height can be adjusted
by lifting the handle in a downward or upward direction
(please see the photos below showing position 1 &
position 2).

NOTE: Ensure the
metal rod is located
in its correct position.

POSITION 1

1

Removing the Dishes

To prevent water dripping from the upper basket into
the lower basket, we recommend that you empty the
lower basket first and then the upper basket.

POSITION 2

Page 15Page 14