Dell W-7200 SFP Installation Manual

Dell PowerConnect W-Series SFP/SFP+

arun_0110

Copper SFP
Form Factor

Fiber SFP
Form Factor

Installation Guide

Introduction

SFP modules, small form-factor pluggable modules, also known as mini-GBICs, are hot-swappable Gigabit
Ethernet optical transceivers. SFP+ modules, small form-factor pluggable modules, are hot-swappable 10 Gigabit
Ethernet optical transceivers.

 SFP-TX: conforms to 1000Base-T copper wiring Gigabit Ethernet standard

 SFP-SX: conforms to 1000Base-SX fiber optic Gigabit Ethernet standard

 SFP-LX: conforms to 1000Base-LX fiber optic Gigabit Ethernet standard

 SFP-10GE-SR: conforms to 10GEBase-SR fiber optic Gigabit Ethernet standard

 SFP-10GE-LR: conforms to 10GEBase-LR fiber optic Gigabit Ethernet standard

 SFP-10GE-LRM: conforms to 10GEBase-LRM fiber optic Gigabit Ethernet standard

NOTE: Approved optics are tested and supported within Dell controller systems. Non-approved, third party optics are not tested or
supported; therefore, proper functionality of non-approved, third party optics are not guaranteed. For a complete list of approved
optics, contact your Dell sales representative.

Specifications

Figure 1 shows the physical form factor of the copper and fiber based SFP modules.

Figure 1

SFP-TX

Table 1 describes the specifications for the SFP-TX module.

Parameter Specification

Connector Type RJ-45

Cable Type and Maximum Range Cat 5, 5E, 6/Range up to 100 m

SFP Module Form Factor

0510792-03 | February 2013 1

SFP-SX

Table 2 describes the specifications for the SFP-SX module.

Parameter Specification

Connector Type LC fiber optic

Cable Type and Maximum Range 62.5 m multi-mode fiber/Range up to 260 m (850 feet)

50 m multi-mode fiber/Range up to 550 m (1800 feet)

Input Wavelength 770 to 860 nm

Center Wavelength 830 to 860 nm

SFP-LX

Table 3 describes the specifications for the SFP-LX module.

Parameter Specification

Connector Type LC fiber optic

Cable Type and Maximum Range 9 m single-mode fiber/Range of 10 km (6.21 miles)

Input Wavelength 1260 nm to 1570 nm

Center Wavelength 1310 nm

SFP-10GE-SR

Table 4 describes the specifications for the SFP-10GE-SR module.

Parameter Specification

Connector Type LC fiber optic

Cable Type and Maximum Range 62.5 m multi-mode fiber with 160 MHz/km (FDDI) cable has a range of 26 m (85.3 feet)

62.5 m multi-mode fiber with 200 MHz/km (OM1) cable has a range of 33 m (108.3 feet)

50 m multi-mode fiber with 400 MHz/km cable has a range of 66 m (216.5 feet)

50 m multi-mode fiber with 500MHz/km (OM2) cable has a range of 82 m (269 feet)

50 m multi-mode fiber with 2000 MHz/km (OM3) cable has a range of 300 m (984.3 feet)

Input Wavelength 840 nm to 860 nm

Center Wavelength 850 nm

SFP-10GE-LR

Table 5 describes the specifications for the SFP-10GE-LR module.

Parameter Specification

Connector Type LC fiber optic

Cable Type and Maximum Range 9 m single-mode fiber/Range of 10 km (6.21 miles)

Input Wavelength 1280 nm to 1340 nm

2 Dell PowerConnect W-Series SFP/SFP+ | Installation Guide