Dell PowerConnect B-RX4, PowerConnect W-IAP130 Series, PowerConnect W-AP135 Installation Manual
Dell PowerConnect W-IAP130 Series Instant Access Point
Installation Guide
0511016-01 | January 2012 1
The Dell PowerConnect W-Series W-AP134 and W-AP135 Instant access points support the IEEE 802.11n
standard for high-performance WLAN. These access points use MIMO (Multiple-in, Multiple-out) technology
and support existing 802.11a/b/g/n wireless services.
The Dell W-AP130 Series access points provide the following capabilities:
Virtual Controller technology
Wireless transceiver
Protocol-independent networking functionality
IEEE 802.11a/b/g/n operation as a wireless access point
IEEE 802.11a/b/g/n operation as a wireless air monitor
Compatibility with IEEE 802.3at PoE
Minimum Software Requirements
The W-AP130 Series access point requires Dell PowerConnect W-Instant 6.1.2.3-2.0.0.0 or later.
Package Contents
W-AP134 or W-AP135 access point
Installation guide (this document)
Dell PowerConnect W-Instant Quick Start Guide
9/16” Ceiling Rail Adapter
15/16” Ceiling Rail Adapter
NOTE: Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including the
original packing materials. Use these materials to repack and return the unit to the supplier if needed.
NOTE: Additional mounting kits for use with the W-AP130 Series access points are sold separately. Contact your Dell sales
representative for details.
2 Dell PowerConnect W-IAP130 Series Instant Access Point | Installation Guide
Device Overview
Figure 1 W-AP130 Series Access Points (W-AP134 Shown)
LEDs
The W-AP130 Series access point is equipped with five LEDs that indicate the status of various components of
the device.
PWR—Indicates the whether or not the W-AP130 Series is powered on and its status.
ENET 0—Indicates the status and activity of Ethernet port 0
ENET 1—Indicates the status and activity of Ethernet port 1
11b/g/n—Indicates the status of the 2.4 GHz radio
11a/n—Indicates the status of the 5.0 GHz radio
For more information about the LEDs and their behavior, see Table 3 on page 8.
External Antenna Connectors
The W-AP134 is designed for use with external antennas. The W-AP135 is equipped with internal antennas. For
more information about antenna types and configurations, visit dell.com.
AP-134_003
134
Antenna Connectors (W-AP134 Only)
LED Status Indicators
Dell PowerConnect W-IAP130 Series Instant Access Point | Installation Guide 3
Figure 2 W-AP130 Series Access Point Rear
Console Port
Use the console port to connect to a terminal for direct local management.
Ethernet Ports
W-AP130 Series access points are equipped with two 10/100/1000Base-T (RJ-45) auto-sensing, MDI/MDX wirednetwork connectivity ports. These ports support IEEE 802.3at Power over Ethernet (PoE) compliance, accepting
56 VDC as a standard defined Powered Device (PD) from a Power Sourcing Equipment (PSE) such as a PoE
midspan injector, or network infrastructure that supports PoE.
DC Power Socket
If PoE is not available, an optional Dell power adapter kit (sold separately) can be used to power the
access point.
Reset Button
The reset button can be used to return the access point to factory default settings. To reset the access point:
1. Power off the W-IAP130 Series by removing the Ethernet cable (POE) or power adapter cable.
2. Press and hold the reset button using a small, narrow object, such as a paperclip.
3. Power-on the access point without releasing the reset button. The power LED will flash within 5 seconds.
4. Release the reset button.
AP-134_002
CONSOLE
ENET 1
ENET 0
Reset Button
DC Power Socket
Kensington Security Slot
NOTE: Use the ENET 0 port for uplink connections to a switch or router. The ENET 1 port does not provide wired connectivity.
4 Dell PowerConnect W-IAP130 Series Instant Access Point | Installation Guide
The power LED will flash again within 15 seconds indicating that the reset is completed. The access point will
now continue to boot with the factory default settings.
Kensington Lock Slot
The access point is equipped with a Kensington security slot for additional security.
Before You Begin
Pre-Installation Checklist
Before installing your access point, be sure that you have the following:
For the W-AP134—External antennas as specified in the network deployment plan
CAT5 or better UTP cable of required length
One of the following power sources:
IEEE 802.3at-compliant Power over Ethernet (PoE) source
The POE source can be any power source equipment (PSE)
Dell 12 power adapter kit (sold separately)
Summary of the Setup Process
Successful setup of an access point consists of five tasks, which must be performed in this order:
1. Verify pre-installation connectivity.
2. Identify the specific installation location for each AP.
3. Install each IAP.
4. Verify post-installation connectivity.
CAUTION: FCC Statement—Improper termination of access points installed in the United States configured to non-US model
controllers will be in violation of the FCC grant of equipment authorization. Any such willful or intentional violation may result in a
requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80).
CAUTION: EU Statement:
Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the Dell PowerConnect W-Series Dell
PowerConnect W-Instant 6.1.2.3-2.0.0.0 User Guide for details on restrictions.
Produit réseau local radio basse puissance operant dans la bande fréquence 2.4 GHz et 5 GHz. Merci de vous referrer au Dell
PowerConnect W-Series Dell PowerConnect W-Instant 6.1.2.3-2.0.0.0User Guide pour les details des restrictions.
Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet. Weitere Informationen bezlüglich Einschränkungen
finden Sie im Dell PowerConnect W-Series Dell PowerConnect W-Instant 6.1.2.3-2.0.0.0 User Guide.
Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare riferimento alla Dell PowerConnect W-Series Dell
PowerConnect W-Instant 6.1.2.3-2.0.0.0 User Guide per avere informazioni detagliate sulle restrizioni.
NOTE: It is important that you verify the items listed under Pre-Installation Checklist before you attempt to set up and install an
AP.
Dell PowerConnect W-IAP130 Series Instant Access Point | Installation Guide 5
5. Configure each IAP.
Identifying Specific Installation Locations
You can mount the access point on a ceiling rail (using the included adapter) or on a wall (using the wall mount
adapter, sold separately). Each location should be as close as possible to the center of the intended coverage area
and should be free from obstructions or obvious sources of interference. These RF absorbers/reflectors/
interference sources will impact RF propagation and should have been accounted for during the planning phase
and adjusted for in RF plan.
Unidentified Known RF Absorbers/Reflectors/Interference Sources
Identifying known RF absorbers, reflectors, and interference sources while in the field during the installation
phase is critical. Make sure that these sources are taken into consideration when you attach an AP to its fixed
location. Examples of sources that degrade RF performance include:
Cement and brick
Objects that contain water
Metal
Microwave ovens
Wireless phones and headsets
CAUTION: Access points are radio transmission devices and as such are subject to governmental regulation. Network
administrators responsible for the configuration and operation of access points must comply with local broadcast regulations.
Specifically, access points must use channel assignments appropriate to the location in which the access point will be used.
NOTE: Dell, in compliance with governmental requirements, has designed the access points so that only authorized network
administrators can change the settings. For more information about AP configuration, see theDell PowerConnect W-Series Instant
Access Point Quick Start Guide and Dell PowerConnect W-Series Dell PowerConnect W-Instant 6.1.2.3-2.0.0.0 User Guide
at
support.dell.com.
Loading...