Dell KB813 User Manual

Dell™ KB813 Smart Card Keyboard

User Guide

Content

Introduction Setup Using the Keyboard Troubleshooting Speciﬁcations Regulatory Certiﬁcations

Information in this document is subject to change without notice. © 2012 Dell Inc. All rights reserved. Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden. Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc. Microsoft®, Windows®, and Windows Vista® are either trademarks or registered trademarks of Microsoft Corporation in the United States and / or other countries. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

Introduction

Back to Contents Page

Overview

Congratulations on the purchase of your new Dell Smart Card Keyboard.

This user's guide has been developed to provide information that will assist you in the setup and operation of your new smart card keyboard.

The Dell Smart Card Keyboard can be used on PC systems running Windows 2000, Windows XP (32/64 bit), Windows Vista (32/64 bit), Windows 7 (32/64 bits), Window 8 (32/64 bits), Windows Server 2003, Windows Server 2008, Windows Server 2008 R2, Windows Server 2012, Linux Ubuntu, OpenSuse and RedHat.

This product can be used for banking transactions, identiﬁcation systems, secure web applications, and secure logon. This smart card interface can be used with all microprocessor smart cards.

For more details see Features.

Overview | System Requirement | Features

Back to Contents Page

Setup

NOTE: The drivers are already factory installed if the keyboard is purchased with computer. This section is included in case you have to re-load your operating system.

Install the Keyboard

Connect the Keyboard to any USB port on the computer. The USB port shown in the diagram is at the rear of the computer. USB ports may also be located at the front.

Follow the instructions in Install the driver section.

Overview | System Requirement | Features

Back to Contents Page

System Requirements

In order to properly install and operate your Dell Smart Card Keyboard, the following system requirements are necessary:

• Windows 2000, Windows XP (32/64 bit), Windows Vista (32/64 bit), Windows 7 (32/64 bit), Windows 8 (32/64 bit), Windows Server 2003, Windows Server 2008, Windows Server 2008 R2, Windows Server 2012, Linux Ubuntu, OpenSuse, and RedHat.

• The Smart Card Keyboard Driver CD

• One free USB port

Features

• Reads from and writes to all ISO7816-1/2/3/4 microprocessor

smart cards (T=0, T=1) up to 826Kbds (TA1=17) @4.8Mhz depending on smart card

• Supports 3 V, 5 V, and 1.8 V cards

• Powers o automatically when the card is removed

• Smart Card secure PIN entry

• PC/SC 2.0 driver up to Windows 8

Overview | System Requirement | Features

Back to Contents Page

Install the Windows XP driver

1. When the Dell Smart Card Keyboard is plugged into a USB port, the following window will appear:

2. Then the following window will appear:

Back to Contents Page

3. The installation wizard will install the driver. After a successful installation, the system will prompt you with the following message:

4. Select Finish. Your Smartcard Keyboard is now ready for use.

Back to Contents Page

Install the Vista driver

1. When the Dell Smart Card Keyboard is plugged into a USB port, the following window will appear:

2. Wizard will install driver. After a successful installation, the system will prompt you with the following message:

Back to Contents Page

Install the Windows 7 driver

1. When the Dell Smart Card Keyboard is plugged into a USB port the following window will appear:

2. The installation Wizard will install driver. After a successful installation, the system will prompt you with the following message:

Back to Contents Page

Install the Windows 8 driver

1. When the Dell Smart Card Keyboard is plugged into a USB port, the following window will appear:

2. The installation Wizard will install driver. During installation, the system will prompt you with the following window:

3. When installation is completed, your device is ready to use.

Back to Contents Page

Update the Windows XP driver

1. With the Smart Card reader connected, the old driver that is built in inside the operating system will be installed automatically.

2. From the Start Menu, open the Control Panel.

Back to Contents Page

Update the Windows XP driver

3. Double click System. The following window will be shown:

4. Select Hardware. The following screen displays:

Back to Contents Page

Update the Windows XP driver

5. Select Device Manager.

6. The following screen will be shown. Select Smart card readers.