This document provides a list of RACADM subcommands and database objects that are applicable for various iDRAC
versions.
To pi cs :
•RACADM Subcommands
•RACADM Database Objects With get and set Commands
•RACADM Database Objects With getconfig and setconfig Commands
For detailed information about the subcommands and database objects, see the RACADM Command Line Reference Guide
applicable for a particular iDRAC version available at dell.com/esmmanuals.
For information on the older versions of iDRAC6 and iDRAC7, see the RACADM Support Matrix document for the
applicable versions available at dell.com/esmmanuals.
New In This Release
•Support for using a common iDRAC firmware across Dell’s 12th and 13th generation PowerEdge servers. You can apply
the same (2.10.10.10) version on a 13th generation of PowerEdge server with iDRAC8 and a 12th generation of PowerEdge
server with iDRAC7.
–Enables direct upgrade to version 2.10.10.10 from 2
–Supports features such as SNMPv3 traps, combined functionality of Tech Support Report with iDRAC Service
Module, security enhancements, and code stability are supported on the Dell 12th generation of PowerEdge servers.
However, it does not support features that are inherent to the 13th generation of PowerEdge servers and their system
board, such as Easy Restore, optional Quick Sync bezel and so on.
•Support for the following PowerEdge servers:
–PowerEdge FC430
–PowerEdge M830
–PowerEdge FC830
–PowerEdge FD332
•Support to switch the controller mode from RAID to HBA and back on PERC 9.1 and later controllers.
•Support for 256 bit or higher SSL encryption between client and server.
•Support for monitoring chassis events for PowerEdge FX2/FX2s chassis using iDRAC.
•Support for monitoring and inventorying PERC FD33xS and PERC FD33xD controllers on the Dell PowerEdge FD332
storage sled.
.xx.xx.xx
or 1
.xx.xx.
RACADM Subcommands
The following table provides a list of RACADM subcommands that are applicable for various iDRAC versions.
RACADM SubcommandName iDRAC6 VersioniDRAC7 VersioniDRAC8 Version
usercertupload Ye sYe s Yes YesYe sYe sYe sYe sYe s
usercertview YesYe s Yes YesYe sYe sYe sYe sYe s
vflashsd Ye sYe s Yes YesYe sYe sYe sYe sYe s
vflashpartition Ye sYe s Yes YesYe sYe sYe sYe sYe s
vmdisconnect Ye sYe s Yes YesYe sYe sYe sYe sYe s
RACADM Database Objects With getconfig and setconfig
Commands
The following table provides a list of RACADM database objects you can use with getconfig and setconfig commands that
are applicable for various iDRAC versions
RACADM Group
NameRACADM Object Name
cfgStaticLanNetw
orking
cfgRemoteHostscfgRhostsFwUpdateTftp
cfgU s erA d m inc f g Use r Admi n Ind e x Ye sYesYesYesYesYe sYe sYe sYe s
cfgN i cSta t icE n able N oNoYesYes Ye s Yes Yes Ye sYes
cfgN i cSta t icI P v 4En a ble N oN oYesYesYesYe sYe sYe sYe s
cfgN i cSta t icI p A ddre s s NoNoYe sYesYe sYesYesYe sYes
cfgN i cSta t icU s eDhc p NoNoYe sYe sYesYesYe sYe sYes
cfgN i cSta t icN e t mas k NoNoYe sYe sYesYesYe sYe sYes
cfgN i cSta t icG a t ewa y NoNoYe sYe sYesYesYesYe sYes
cfgDNSStaticServersFro
mDHCP
cfgDNSStaticServer1 NoNoYesYesYesYesYesYesYes
cfgDNSStaticServer2NoNoYesYesYesYesYesYesYes
cfgDNSStaticDomainNameN oN oYe sYesYe sYe sYe sYesYe s
cfgDNSStaticDomainNa
meFromDHCP
Enable
cfgRhostsFwUpdateIpAd
dr
cfgR h osts F wUp d a tePa th Ye sYe sYe sYesYe sYe sYesYesYes
cfgRhostsSmtpServerIpA
ddr
cfgR h osts S ysl o g Ena b le YesYe sYe sYesYe sYesYesYesYes
cfgR h osts S ysl o g Po r t YesYesYe sYesYe sYesYesYe sYes
cfgR h osts S ysl o g Ser v er1 Ye sYe sYesYesYe sYe sYe sYesYe s
cfgR h osts S ysl o g Ser v er2 Ye sYe sYesYesYe sYe sYe sYesYe s
cfgR h osts S ysl o g Ser v er3 Ye sYe sYesYesYe sYe sYe sYesYe s
cfgUserAdminIpmiLanPr
ivilege
cfgUserAdminIpmiSerial
Privilege
cfgU s erAd m inPri v ileg e YesYesYe sYesYesYesYe sYe sYes
cfgU s erAd m inU s e rNa m e YesYesYe sYe sYesYesYesYe sYes
cfgU s erAd m inPa sswo r d YesYesYe sYe sYesYesYe sYe sYes
cfgU s erAd m inE n a ble Ye sYesYesYesYesYe sYe sYe sYe s
cfgU s erAd m inS o l Ena b le YesYe sYe sYesYe sYesYesYesYes