Dell EqualLogic PS4100X User Manual
Setting Up a PS Series Storage Array
PS Series Storage Arrays
PS4100 Installation
Before You Begin
This is a condensed reference. Read the safety instructions in your Safety, Environmental, and Regulatory Information booklet before you
begin. Also read the Installation and Setup manual for complete installation information.
Register for an EqualLogic Customer Support account.
If you do not have a customer service support account, go to support.dell.com and create one.
Download and read the Release Notes from the support site.
The PS Series Release Notes contain the latest product information.
Environmental Requirements.
Make sure the installation location meets the power, cooling, and ventilation requirements in the Installation and Setup manual, located in the
shipping box.
Networking Requirements.
Standard Ethernet and TCP/IP networking rules apply to a PS Series SAN. Gigabit Ethernet is recommended for optimal performance.
3
Install the Front Bezel
1. Hold the bezel with the array model number upright.
2. Hook the right end of the bezel onto the right side of the chassis.
3. Swing the left end of the bezel towards the left side of the chassis.
4. Press the bezel into place until the release latch closes.
5. Using the provided key, lock the front bezel. Store the key in a safe place.
Required Hardware (not supplied)
• Standard 19-inch, four-post rack.
• One to four network cables. Supported cables include Category 5E and Category 6 cables with RJ45 connectors. Use Category 5 cables
only if they meet the TIA/EIA TSB95 standard.
1
PS Series Storage Arrays
Software Configuration
Unpack the Shipping Box
Protect sensitive hardware. Make sure you use an electrostatic
wrist strap or similar form of protection when handling hardware.
Make sure the shipping box contains the following items:
1. Setup poster (this document)
2. Rail kit (if ordered)
3. Accessory box, which includes:
- All power cables
- Electrostatic wrist strap
- Translated documentation
- Translation CD-ROM
4. Documentation
5. PS4100 chassis
2
PS SERIES STORAGE ARRAYS
Installation & Setup Manual
4
5
Software Configuration Methods
PS Series Groups
Multi-Member PS Series Group
Step 1: Install the Host Integration Tools
Step 2: Collect Configuration Information
To configure the PS Series software, you need the information
Group1
in the following tables.
Step 3: Run the Remote Setup Wizard
Member name
Array IP address
Subnet mask
Array Configuration
Default gateway
RAID policy
RAID policy
Group name
Group IP address
Group Configuration
Administration
password
Membership
password
CHAP user name
CHAP password
Where to Go Next
Step 4: Start Using the SAN
1
3
4
Connect the Power Cables
Use the power cables shipped with the array to connect each power supply and cooling module to separate sources of
power, if possible. Use the hook and loop fastener to secure the power cables to the power supply modules so they
cannot be pulled out accidentally.
See the Installation and Setup manual for more information.
If the array was not shipped with power cables, see your PS Series support provider or reseller for power cable
information.
2
Install the Array in a Rack
Mount the array in a four-post, 19-inch rack. See the rack instructions that came
with the rail kit in your shipping box (if ordered).
The array is heavy. Do not attempt to lift the array without assistance.
Setting Up a PS Series Storage Array (continued)
5
Connect the Array to the Network
Recommended Configuration: For high performance and
availability, connect network cables to all the network
interfaces and distribute the connections across multiple
network switches. The switches must be connected with
interswitch links that have sufficient bandwidth.
Switch 0
CM0
Switch 1
CM1
6
Turn on Power to the Array
Before turning on power, allow enough time for the
array to adjust to ambient temperature and humidity
(for example, overnight).
The power switch on each power supply module is
located below the power plug. The switch is
oriented vertically. Turn on power to both power
supply modules (in any order).
Note: Batteries will start to charge and some
hardware components may start to synchronize
when power is turned on. Array LEDs will indicate
this normal activity.
Setting Up a PS Series Storage Array
Hardware Installation is Complete.
See the Installation and Setup guide to configure the array
software.
Information in this document is subject to change without
notice.
Reproduction in any manner whatsoever without the written
permission of Dell EqualLogic is strictly forbidden.
The Dell EqualLogic logo is a trademark of Dell, Inc.
Copyright 2011 Dell, Inc. All rights reserved.
Notes, Cautions, and Warnings
A NOTE indicates important information that helps you make
better use of your computer.
A CAUTION indicates potential damage to hardware or loss of
data if instructions are not followed.
A WARNING indicates a potential for property damage, personal
injury, or death.
Printed in U.S.A.
Printed on recycled paper.
R5DM1 rev.A00
Loading...