Dell 1100, ML 1610 User Manual

Remanufacturing Instructions

Dell 1100 / Samsung ML 1610

For Technical Support, please call Memphis, TN at [phone] or Nashua, NH at [phone].

1. On the end cap where the contacts are
located, remove the two screws that secure
the end cap (Fig. 1).

Reference Information: Oasis Products:

Dell # 3106640 Toner: D3TN1070
Samsung # ML1610 Drum: D3DR305
Wiper Blade: D3WB20
OEM Yields: Fuse: 99FZ10
2000 @ 5% coverage

Fig. 1

2. Using a small flat screw driver, release
the locking tab on the bottom side of the
end cap (Fig. 2).

Fig. 2

Remanufacturing Instructions

Dell 1100 / Samsung ML 1610

Memphis, TN [phone]

Nashua, NH [phone]

Technical Support

© 1998 Oasis Imaging Products, Inc. Page 1 of 9

3. Using a small flat screw driver, gently
pry and remove the end cap from the
cartridge (Fig. 3).

Fig. 3

4. Remove the two screws that secure the
waste bin to the cartridge (Fig. 4).

5. The waste bin is held in place by a post
that sits in a slot on the end cap. Push the
waste bin up towards the handle to remove
the post from the slot on this end cap. Set the
waste bin to the side (Fig. 5).

Fig. 4

Fig. 5

Remanufacturing Instructions

Dell 1100 / Samsung ML 1610

Memphis, TN [phone]

Nashua, NH [phone]

Technical Support

© 1998 Oasis Imaging Products, Inc. Page 2 of 9

6. Remove the two screws that hold the
opposite end cap in place (Fig. 6).

Fig. 6

7. Use a small flat screw driver to pry up the
end cap to remove it (Fig. 7).
Set the toner hopper to the side.

8. Remove the two screws that secure the
wiper blade to the waste bin (Fig. 8).

Fig. 7

Fig. 8

Remanufacturing Instructions

Dell 1100 / Samsung ML 1610

Memphis, TN [phone]

Nashua, NH [phone]

Technical Support

© 1998 Oasis Imaging Products, Inc. Page 3 of 9

9. Remove the wiper blade. Clean all residual
toner from the waste bin. Inspect the recovery
blade. Replace the wiper blade and set the
waste bin to the side for reassembly (Fig. 9).

Fig. 9

10. Remove the four gears from the side
of the toner hopper (Fig 10).

11. Remove the PCR by sliding it toward
the gear end of the cartridge and lifting the
post once clear from the Saddle (Fig. 11).
Clean PCR and set aside for Reassembly.

Fig.10

Fig. 11

Remanufacturing Instructions

Dell 1100 / Samsung ML 1610

Memphis, TN [phone]

Nashua, NH [phone]

Technical Support

© 1998 Oasis Imaging Products, Inc. Page 4 of 9

12. Remove the drum and replace during
reassembly (Fig. 12).

Fig. 12

13. Remove the fill plug and clean out
residual toner from the hopper.

Using a small flat screw driver, pry up the
locking tab that secures the developer roller
stabilizer plate (Fig. 13).

14. Lift up the end of the small spring
that comes in contact with the developer
roller end post, and then remove the
stabilizer plate (Fig.14).

Fig. 13

Fig. 14

© 1998 Oasis Imaging Products, Inc. Page 5 of 9

15. Remove the developer roller and clean
with compressed air and a lint free, wax free
wipe (Fig.15).

16. Remove the two screws that secure the
doctor blade to the toner hopper (Fig. 16).

17. The opposite end of the spring, that
rides on the developer roller post, sits in a
small notch on the doctor blade. Move the
spring to the end of the doctor blade, so not
to damage it during removal of the blade.

Make a note of the orientation of the spring
for reassembly (Fig. 17).

Fig. 15

Fig. 16

Fig. 17

Remanufacturing Instructions

Dell 1100 / Samsung ML 1610

Memphis, TN [phone]

Nashua, NH [phone]

Technical Support

© 1998 Oasis Imaging Products, Inc. Page 6 of 9

18. Remove the doctor blade, clean
thoroughly, and set to the side for
reassembly (Fig. 18).

Fig. 18

19. Clean the adder roller thoroughly with
compressed air, and then clean the toner
hopper of all residual toner (Fig. 19).

20. Clean, inspect and replace all
components. Add toner and reassemble
in reverse order (Fig. 20).

Fig. 19

Fig. 20

Remanufacturing Instructions

Dell 1100 / Samsung ML 1610

Memphis, TN [phone]

Nashua, NH [phone]

Technical Support

© 1998 Oasis Imaging Products, Inc. Page 7 of 9

21. Replace or add (starter carts have no
fuse) a fuse that is located on the right front
corner of the cartridge for the Dell 1100 (Fig.

21).

Fig. 21

Remanufacturing Instructions

Dell 1100 / Samsung ML 1610

Memphis, TN [phone]

Nashua, NH [phone]

Technical Support

Oasis and You … Succeeding Together!

New Hampshire Tennessee Texas Canada

[phone] [phone] [phone] [phone]
[phone] Fax: [phone] [phone] [phone]
Fax: [phone] Fax: [phone] Fax: [phone]

Illinois California North Carolina Europe

[phone] [phone] [phone]
[phone] [phone] [phone]
Fax: [phone] Fax: [phone] Fax: [phone]

© 2003 Oasis Imaging Products, Inc. Any attempt to reproduce any part of these instructions without the written cons ent of
Oasis Imaging Products, Inc. may result in legal action. All registered trademarks are the property of their respective owners.

Netherlands

011-31-24-388-2233
Fax: [phone]

© 1998 Oasis Imaging Products, Inc. Page 8 of 9

© 1998 Oasis Imaging Products, Inc. Page 9 of 9