Delfield F18SR Service Manual

F18 SERIES

Service and Installation Manual

Please read this manual completely before attempting to install or operate this equipment! Notify carrier of damage! Inspect all
components immediately.

Refrigerated Work Tables, Salad Tables & Freezer Bases

IMPORTANT INFORMATION

READ BEFORE USE

September 2010

PLEASE SAVE THESE INSTRUCTIONS!

F18 Series Service and Installation Manual

Important Warning And Safety Information

WARNING Read This Manual Thoroughly Before Operating, Installing, Or Performing

Maintenance On The Equipment.

WARNING Failure To Follow Instructions In This Manual Can Cause Property Damage,

Injury Or Death.

WARNING Do Not Store Or Use Gasoline Or Other Flammable Vapors Or Liquids In The

Vicinity Of This Or Any Other Appliance.

WARNING Unless All Cover And Access Panels Are In Place And Properly Secured, Do

Not Operate This Equipment.

WARNING Do Not Clean With Water Jet.

CAUTION Observe the following:

Minimum clearances must be maintained from all walls and combustible

•
materials.

Keep the equipment area free and clear of combustible material.

•

Adequate clearance for air openings.

•

Operate equipment only on the type of electricity indicated on the

•
specification plate.

Retain this manual for future reference.

•

2

For customer service, call [phone], [phone], Fax [phone], www.delfield.com

F18 Series Service and Installation Manual

Contents

Serial Number Location ........................................................3

Receiving & Inspecting .........................................................3

Specifications .................................................................... 4-6

Installation ............................................................................7

Operation ..............................................................................8

Pressure Control Settings .....................................................8

Maintenance .................................................................... 9-10

Wiring Diagrams ........................................................... 11-12

Replacement Part Lists ................................................. 13-16

Replacement Part Assemblies ...................................... 17-20

Warranties..................................................................... 21-23

Serial Number Location

The serial number on all self-contained F18 Series refrigerated
work tables and freezer bases is located on the electrical
specifications tag affixed inside the compressor section next
to the pressure control.

On remote refrigerated bases with doors, the tag is inside the
unit on the coil side. On remote refrigerated bases with drawers,
the tag is affixed to the drawer divider. On remote freezer bases,
the tag is located on the inside back of the unit.

Always have the serial number of your unit available when
calling for parts or service. A complete list of authorized
Delfield parts depots is available at www.delfield.com.

©2010 The Delfield Company. All rights reserved. Reproduction without
written permission is prohibited. “Delfield” is a registered trademark of The
Delfield Company.

Receiving and Inspecting the Equipment

Even though most equipment is shipped crated, care should be
taken during unloading so the equipment is not damaged while
being moved into the building.

1. Visually inspect the exterior of the package an skid or
container. Any damage should be noted and reported to
the delivering carrier immediately.

2. If damaged, open and inspect the contents with the
carrier.

3. In the event that the exterior is not damaged, yet upon
opening, there is concealed damage to the equipment
notify the carrier. Notification should be made verbally as
well as in written form.

4. Request an inspection of the concealed equipment. This
should be done within 10 days from receipt of the
equipment.

5. Check the lower portion of the unit to be sure legs or
casters are not bent.

6. Also open the compressor compartment housing and

7. Freight carriers can supply the necessary forms upon

8. Retain all crating material until an inspection has been

Uncrating the Equipment

First cut and remove the banding from around the crate.
Remove the front of the crate material, use of some tools will
be required. If the unit is on legs remove the top of the crate as
well and lift the unit off the skid. If the unit is on casters it can
be "rolled" off the skid.

visually inspect the refrigeration package. Be sure lines are
secure and base is still intact.

request.

made or waived.

For customer service, call [phone], [phone], Fax [phone], www.delfield.com

3

F18 Series Service and Installation Manual

Specifications

Remote Refrigerated Work Tables

Model # Of Doors

F18WR31

F18WR39

F18WR44

F18WR52

F18WR60

F18WR70

F18WR79

F18WR87

(1) 19” & (1) 27” 70/124 15.12 6.51 115/60/1 3.0 686 120/6°

(2) 27” & (1) 19” 124/70 24.48 10.29 115/60/1 6.0 1050 240/4°

(1) 19” 70 7.56 2.56 115/60/1 3.0 383 120/3°

(1) 27” 124 10.23 3.95 115/60/1 3.0 465 120/4°

(2) 19” 70 12.14 5.12 115/60/1 3.0 605 120/5°

(2) 27” 124 18.10 7.90 115/60/1 3.0 768 120/6°

(2) 32” 140 21.23 9.64 115/60/1 3.0 869 120/7°

(3) 27” 124 27.46 11.85 115/60/1 6.0 1131 240/5°

Shelf Max
Load (lbs)

Self-Contained Refrigerated Work Tables

Model # Of Doors

F18WC39

F18WC47

F18WC52

F18WC60

F18WC68

F18WC78

F18WC87

F18WC95

(1) 19” & (1) 27” 70/124 15.12 6.51 115/60/1 8.0 686 1462 16 1/5 5-15P

(2) 27” & (1) 19” 124/70 24.48 10.29 115/60/1 10.0 1050 2261 16 1/4 5-15P

(1) 19” 70 7.56 2.56 115/60/1 8.0 383 1462 16 1/5 5-15P

(1) 27” 124 10.23 3.95 115/60/1 8.0 465 1462 16 1/5 5-15P

(2) 19” 70 12.14 5.12 115/60/1 8.0 605 1462 16 1/5 5-15P

(2) 27” 124 18.10 7.90 115/60/1 10.0 768 1462 16 1/4 5-15P

(2) 32” 140 21.23 9.64 115/60/1 10.0 869 1994 16 1/4 5-15P

(3) 27” 124 27.46 11.85 115/60/1 10.0 1131 2261 16 1/4 5-15P

Shelf Max
Load (lbs)

Base Storage

Cap. FT

Base Storage

Cap. FT

3

3

Shelf

Area FT

Shelf

Area FT

Volts/Hertz/

2

Phase Amps BTU Load EVAP. BTU/°TD

Volts/Hertz/

2

Phase Amps BTU Load BTU System Cap.

R-404A

oz. H.P.

NEMA

Plug

Remote Refrigerated Mega Top Salad Tables

Model # Of Doors

F18MR31A

F18MR44A

F18MR44D

F18MR52A

F18MR52D

F18MR52E

(1) 19” & (1) 27” 70/124 8.97 6 115/60/1 3.0 515/265 120/4°/12/22°

(1) 19” & (1) 27” 70/124 8.97 12 115/60/1 3.0 515/529 120/4°/22/25°

(1) 19” & (1) 27” 70/124 8.97 18 115/60/1 3.0 515/794 120/4°/31/26°

Shelf Max
Load (lbs)

(1) 19” 70 4.14 6 115/60/1 3.0 280/265 120/2°/12/22°

(2) 19” 70 7.15 6 115/60/1 3.0 444/265 120/4°/12/22°

(2) 19” 70 7.15 12 115/60/1 3.0 444/529 120/4°/22/25°

Base Storage

Cap. FT3# of Pans

Self-Contained Refrigerated Mega Top Salad Tables

Model # Of Doors

F18MC39A

F18MC39D

F18MC52A

F18MC52D

F18MC52E

F18MC60A

F18MC60D

F18MC60E

F18MC60F

(1) 19” & (1) 27” 70/124 8.97 6 115/60/1 10.0 515/265 2314/864 16 1/4 5-15P

(1) 19” & (1) 27” 70/124 8.97 12 115/60/1 10.0 515/529 2314/1141 16 1/4 5-15P

(1) 19” & (1) 27” 70/124 8.97 18 115/60/1 10.0 515/794 2314/1361 16 1/4 5-15P

(1) 19” & (1) 27” 70/124 8.97 24 115/60/1 10.0 515/1058 2314/1540 16 1/4 5-15P

Shelf Max
Load (lbs)

(1) 19” 70 4.14 6 115/60/1 10.0 280/265 1903/925 16 1/4 5-15P

(1) 19” 70 4.14 12 115/60/1 10.0 280/529 1903/1156 16 1/4 5-15P

(2) 19” 70 7.15 6 115/60/1 10.0 444/265 1903/925 16 1/4 5-15P

(2) 19” 70 7.15 12 115/60/1 10.0 444/529 1903/1156 16 1/4 5-15P

(2) 19” 70 7.15 18 115/60/1 10.0 444/794 1903/1321 16 1/4 5-15P

Base Storage

Cap. FT3# of Pans

Volts/Hertz/

Phase Amps

Volts/Hertz/

Phase Amps

BTU Load
Base/Rail

BTU Load
Base/Rail

EVAP. BTU/°TD

Base/Rail

BTU System Cap.

Base/Rail

R-404A

oz. H.P.

NEMA

Plug

4

For customer service, call [phone], [phone], Fax [phone], www.delfield.com

Specifications

Remote Refrigerated Salad Top Tables

Model # Of Doors

F18SR31A

F18SR44A

F18SR44B

F18SR44C

F18SR52A

F18SR52B

F18SR52C

F18SR52D

(1) 19” & (1) 27” 70/124 8.97 6 115/60/1 3.0 532/529 120/4°/13/21°

(1) 19” & (1) 27” 70/124 8.97 8 115/60/1 3.0 532/529 120/4°/16/22°

(1) 19” & (1) 27” 70/124 8.97 10 115/60/1 3.0 532/529 120/4°/19/23°

(1) 19” & (1) 27” 70/124 8.97 12 115/60/1 3.0 532/529 120/4°/23/23°

(1) 19” 70 4.14 6 115/60/1 3.0 280/265 120/2°/13/21°

(2) 19” 70 7.15 6 115/60/1 3.0 491/441 120/4°/13/21°

(2) 19” 70 7.15 8 115/60/1 3.0 491/441 120/4°/16/22°

(2) 19” 70 7.15 10 115/60/1 3.0 491/441 120/4°/19/23°

Shelf Max
Load (lbs)

Self-Contained Refrigerated Salad Top Tables

Model # Of Doors

F18SC39A

F18SC39B

F18SC52A

F18SC52B

F18SC52C

F18SC52D

F18SC60A

F18SC60B

F18SC60C

F18SC60D

(1) 19” & (1) 27” 70/124 8.97 6 115/60/1 10.0 515/265 2314/667 16 1/4 5-15P

(1) 19” & (1) 27” 70/124 8.97 8 115/60/1 10.0 515/353 2314/798 16 1/4 5-15P

(1) 19” & (1) 27” 70/124 8.97 10 115/60/1 10.0 515/441 2314/916 16 1/4 5-15P

(1) 19” & (1) 27” 70/124 8.97 12 115/60/1 10.0 515/529 2314/1023 16 1/4 5-15P

(1) 19” 70 4.14 6 115/60/1 10.0 280/265 1903/745 16 1/4 5-15P

(1) 19” 70 4.14 8 115/60/1 10.0 280/353 1903/867 16 1/4 5-15P

(2) 19” 70 7.15 6 115/60/1 10.0 444/265 1903/745 16 1/4 5-15P

(2) 19” 70 7.15 8 115/60/1 10.0 444/353 1903/867 16 1/4 5-15P

(2) 19” 70 7.15 10 115/60/1 10.0 444/441 1903/971 16 1/4 5-15P

(2) 19” 70 7.15 12 115/60/1 10.0 444/529 1903/1061 16 1/4 5-15P

Shelf Max
Load (lbs)

Base Storage

Cap. FT

Base Storage

Cap. FT

F18 Series Service and Installation Manual

# of

3

3

Pans

# of

Pans

Volts/Hertz/

Phase Amps

Volts/Hertz/

Phase Amps

BTU Load
Base/Rail

BTU Load
Base/Rail

Evap. BTU/°TD

Base/Rail

BTU System

Cap. Base/Rail

R-404A

oz. H.P.

NEMA

Plug

Remote Refrigerated Reduced Height Rail

Model # Of Doors

F18DR44

F18DR52

F18DR60

F18DR70

F18DR79

F18DR87

(1) 19” & (1) 27” 70/124 13.89 6.51 12 115/60/1 3.0 625/529 120/5°/23/23°

(1) 19” & (2) 27” 70/124 22.47 10.29 18 115/60/1 5.0 962/882 240/4°/36/25°

Shelf Max
Load (lbs)

(2) 19” 70 9.54 5.12 10 115/60/1 3.0 547/441 120/5°/19/23°

(2) 27” 124 16.64 7.9 16 115/60/1 5.0 703/617 120/6°/26/24°

(2) 32” 140 22.96 9.64 18 115/60/1 5.0 800/794 120/7°/32/24°

(3) 27” 124 25.22 11.85 22 115/60/1 5.0 1032/970 240/4°/39/25°

Base Storage

Cap. FT

3

Self-Contained Refrigerated Reduced Height Rail

Model # Of Doors

F18DC52

F18DC60

F18DC68

F18DC82

F18DC91

F18DC99

(1) 19” & (1) 27” 70/124 13.89 6.51 14 115/60/1 12.0 625/617 2314/1121 24 1/3 5-15P

(1) 19” & (2) 27” 70/124 22.47 10.29 22 115/60/1 14.0 962/1058 3807/1839 32 1/2 5-20P

Shelf Max
Load (lbs)

(2) 19” 70 9.54 5.12 12 115/60/1 10.0 547/529 1903/1061 16 1/4 5-15P

(2) 27” 124 16.64 7.9 18 115/60/1 12.0 703/794 2314/1544 24 1/3 5-15P

(2) 32” 140 22.96 9.64 20 115/60/1 14.0 800/882 3097/1648 32 1/2 5-20P

(3) 27” 124 25.22 11.85 24 115/60/1 14.0 1032/1147 3807/1839 32 1/2 5-20P

Base Storage

Cap. FT

3

Shelf

Area FT

Shelf

Area FT

# of

Pans

# of

Pans

Volts/Hertz/

Phase Amps

Volts/Hertz/

Phase Amps

2

2

BTU Load
Base/Rail

BTU Load
Base/Rail

Evap. BTU/°TD

Base/Rail

BTU System

Cap. Base/Rail

R-404A

oz. H.P.

NEMA

Plug

For customer service, call [phone], [phone], Fax [phone], www.delfield.com

5

F18 Series Service and Installation Manual

Specifications

Remote Refrigerated Reduced Height Rail

Model # Of Doors

F18RR44

F18RR52

F18RR60

F18RR70

F18RR79

F18RR87

(1) 19” & (1) 27” 70/124 11.81 6.51 115/60/1 3.0 625/529 120/5°/23/23° 12

(1) 19” & (2) 27” 70/124 18.68 10.29 115/60/1 5.0 962/882 240/4°/36/25° 18

(2) 19” 70 9.49 5.12 115/60/1 3.0 547/441 120/5°/19/23° 10

(2) 27” 124 14.14 7.9 115/60/1 5.0 703/617 120/6°/26/24° 16

(2) 32” 140 17.05 9.64 115/60/1 5.0 800/794 120/7°/32/24° 18

(3) 27” 124 21.30 11.85 115/60/1 5.0 1032/970 240/4°/39/25° 22

Shelf Max
Load (lbs)

Self-Contained Refrigerated Reduced Height Rail

Model # Of Doors

F18RC52

F18RC60

F18RC68

F18RC82

F18RC91

F18RC99

(1) 19” & (1) 27” 70/124 11.81 6.51 115/60/1 12.0 625/617 2314/1121 14 24 1/3 5-15P

(1) 19” & (2) 27” 70/124 18.68 10.29 115/60/1 14.0 962/1058 3807/1839 22 32 1/2 5-20P

(2) 19” 70 9.49 5.12 115/60/1 10.0 547/529 1903/1061 12 16 1/4 5-15P

(2) 27” 124 14.14 7.9 115/60/1 12.0 703/794 2314/1544 16 24 1/3 5-15P

(2) 32” 140 17.05 9.64 115/60/1 14.0 800/882 3097/1648 20 32 1/2 5-20P

(3) 27” 124 21.30 11.85 115/60/1 14.0 1032/1147 3807/1839 24 32 1/2 5-20P

Shelf Max
Load (lbs)

Base Storage

Cap. FT

Base Storage

Cap. FT

3

3

Shelf

Area FT

Shelf

Area FT

Volts/Hertz/

2

Phase Amps

Volts/Hertz/

2

Phase Amps

BTU Load
Base/Rail

BTU Load
Base/Rail

Evap. BTU/°TD

Base/Rail

BTU System

Cap. Base/Rail

# of

Pans

# of

Pans

R-404A

oz. H.P.

NEMA

Plug

Remote Freezer Base

Model # Of Doors

F18FR35

F18FR50

F18FR58

F18FR66

F18FR76

(1) 19” 70 5.58 2.56 115/60/1 10.0 943 160/6°

(2) 19” 70 12.21 5.12 115/60/1 10.0 1471 160/9°

(1) 19” & (1) 27” 70/124 15.00 6.51 115/60/1 10.0 1844 160/10°

(2) 27” 124 17.79 7.9 115/60/1 10.0 2020 160/11°

(2) 32” 140 21.28 9.64 115/60/1 10.0 2437 160/13°

Self-Contained Freezer Base

Model # Of Doors

F18FC43

F18FC62

F18FC70

F18FC78

F18FC88

(1) 19” 70 5.58 2.56 115/60/1 10.0 943 1558 1/3 24 5-15P

(2) 19” 70 12.21 5.12 115/60/1 12.0 1471 1776 1/2 40 5-15P

(1) 19” & (1) 27” 70/124 15.00 6.51 115/60/1 16.0 1647 2713 3/4 56 5-20P

(2) 27” 124 17.79 7.9 115/60/1 16.0 1824 2713 3/4 56 5-20P

(2) 32” 140 21.28 9.64 115/60/1 16.0 2045 2713 3/4 56 5-20P

Self-Contained Dual Rails

Model # Of Doors

F18PD48

F18PD72

(1) 27”

(2) 27”

Shelf Max
Load (lbs)

Shelf Max
Load (lbs)

Shelf Max
Load (lbs)

124

124

Base Storage

Base Storage

Base Storage

3

Cap. FT

3

Cap. FT

3

Cap. FT

9.38 3.95

16.64 7.90

Shelf

Area FT

Shelf

Area FT

Shelf

Area FT

Volts/Hertz/

2

Phase Amps

Volts/Hertz/

2

Phase Amps

Volts/Hertz/

2

Phase Amps

115/60/1 10.0 424/1058 2001/1865 1/5, 1/3 40 5-20P

115/60/1 12.7 703/1588 2001/3174 1/5. 1/2 48 5-20P

BTU Load
Base/Rail Evap. BTU/°TD

BTU Load
Base/Rail

BTU Load
Base/Rail

BTU System

Cap. Base/Rail H.P.

BTU System

Cap. Base/Rail H.P.

R-404A

oz.

R-404A

oz.

NEMA

Plug

NEMA

Plug

6

For customer service, call [phone], [phone], Fax [phone], www.delfield.com

CAUTION

Installation

F18 Series Service and Installation Manual

Location

These units are intended for indoor use only. Be sure the
location chosen has a floor strong enough to support the
total weight of the cabinet and contents. A fully loaded 72”
(183cm) long model may weigh as much as 1500 pounds
(680kg)! Reinforce the floor as necessary to provide for
maximum loading.

It is very important to allow for proper air flow, both inside
and outside.

Avoid hot corners and locations near stoves, ovens and
other pieces of cooking equipment.

It is recommended that the unit be installed no
closer than 1” (2.54cm) from any wall. Do not
install the unit near any combustible material or
object affected by heat or moisture.

PDL models also require 14" (36cm) clearance
at the top and 6" (15cm) clearance at the bottom
(casters).

Leveling

A level cabinet looks better and will perform better because
the drain pan will drain properly, the doors will line up with
the frames properly, and the cabinet will not be subject to
undue strain.

A unit on legs will have an adjustable bullet foot on each
leg, adjust each for a level unit. A unit on casters will not
be adjustable. Be sure the unit is on a level floor, make
necessary changes to the floor for proper level.

Lock all front casters to ensure the stability of the unit.

Plumbing

Self-contained models are standard with a condensate evaporator.
If, for some reason a unit does not have a condensate evaporator,
or if the evaporator fails, the unit’s drain must have an outlet to
an appropriate drainage area or container. A refrigerated rail
will have a 1" (2.54cm) drain which will need to be run to an
appropriate floor drain or container. The drain will be stubbed
to the bottom of the machine compartment. Either run drain
to a floor drain or add a valve to the base of the machine
compartment and drain the rail to a container when convenient.
The LiquiTec option will NOT have a drain available.

Moisture collecting from improper drainage can
create a slippery surface on the floor and a hazard
to employees. It is the owner’s responsibility to
provide a container or outlet for drainage.

Electrical connection

Refer to the specification pages amperage data, the serial tag,
your local code or the National Electrical Code to be sure the unit
is connected to the proper power source. A protected circuit of
the correct voltage and amperage must be run for connection of
the line cord, or permanent connection of the unit.

Self-contained units with a cord and plug have an ON/OFF
switch located directly behind the louvered panel covering the
compressor section. Simply turn the switch to ON to begin
operation.

The power switch must be turned to OFF and the
unit disconnected from the power source whenever
performing service or maintenance functions.

Never operate the unit without the louvered panel
in place!

If electrical receptacles are to be mounted in the unit’s
backsplash, they must be wired independently from the
existing unit wiring.

For customer service, call [phone], [phone], Fax [phone], www.delfield.com

7

F18 Series Service and Installation Manual

Operation

After turning the ON/OFF switch to ON the unit’s compressor
will begin operating. Delfield refrigerated bases are designed
to maintain an operational temperature of 36°F to 40°F (2°C to
4°C). Temperature in the salad top and refrigerated rail opening
is 33°F to 41°F (0°C to 5°C) with pans recessed 2” (5.1cm) on
a standard wrapped refrigerated rail or flush with the LiquiTec
option at 86°F (30°C) ambient room temperature. Freezer
bases are designed to maintain an operational temperature of
0°F (-18°C).

Do not place hot pans on/against the blue ABS liner.
Do not throw items into the storage area. Failure
to heed these recommendations could result in
damage to the interior of the cabinet or to the
blower coil.

Overloading the storage area, restricting the air
flow, and continuous opening and closing of the
doors and drawers will hamper the units ability to
maintain operational temperature.

Refrigerated rail units

Product in the rail should be removed to the refrigerated base
at the end of the day. This allows you to turn the rail off at night
to save energy and the rail will have time to defrost as needed.
It also helps maintain product quality. The standard wrapped
refrigerated units are controlled by the pressure control which
is set to maintain the proper rail temperature. An on/off switch
is also provided for the rail and is required to be shut off at
night. The rail switch shuts off the rail only. With a LiquiTec rail
a thermostat is provided to maintain rail temperature as well as
the rail on/off switch. The LiquiTec rail is required to be shut
off at night as well to allow for defrosting. To ensure product
quality in the rail it is recommended that product be rotated
every four hours.

If adding any item to the unit, be sure to keep
in mind the location of the refrigeration lines on
wrapped rail units. A refrigeration leak in a rail
is extremely difficult and costly to repair. In some
cases it cannot be repaired at all.

Pressure Control Settings

Factory recommended low-pressure control settings are:

HFC-404A refrigerators: 85psi (5.86bar) cut-in and 65psi

(4.48bar) cut-out to maintain
approximate interior temperature of
38°F (3°C).
Differential setting of 20psi (1.38bar).

HFC-404A freezers: 32psi (2.21bar) cut-in and 8psi (.552bar)

cut-out to maintain approximate
interior temperature of 0°F to 5°F
(-18°C to -15°C).
Differential setting of 24psi (1.65bar).

HFC-404A refrigerators with LiquiTec Rail:

20psi (1.38bar) cut-in and 10psi

(.689bar) cut-out
Differential setting of 10psi (.689bar)
Temperature control for LiquiTec Rail,

25°F (-4°C) cut in and 18°F (-8°C) cut-

out.

Pressure control settings are measured in pressure,
not temperature.

8

For customer service, call [phone], [phone], Fax [phone], www.delfield.com