Delfield F18RC52, F18RC72, F18RC60, F18RC82, F18RC91 Specification Sheet
...
Optional Accessories & Modifications
906A Stainless steel end
505H Stainless steel back
505F Laminate facing (full front)
906E Laminate end
905A Laminate back
1030A Cutting board (Sanalite or composite)
107F Tray rack
1027A Casters
102 Drawers
A-(2) 19” in lieu of one door
B-(2) 27” in lieu of one door
C-(2) 32” in lieu of one door
108 Locks
120F Cold pan drain
213 *220V/50 cycle
*Inclusion of this option will alter the
electrical specifications of the unit
Short Form Specifications
Exterior top is one-piece, 16-gauge stainless steel, with integral 2.12”
(5.4cm) high square nosing on front. Top has a mechanically cooled refrigerated raised rail at rear with openings to accommodate 1/6 size pans. Pans and
adapter bars are provided by others. Pans are recessed 3” (7.6cm) or 2”
(5.1cm) and set on adjustable stainless steel pan supports. Rail interior is 22gauge stainless steel. Raised rail openings have 20-gauge stainless steel removable lids. Unit is equipped with separate expansion valve and on/off switch for
refrigerated cold pan. Temperature in top opening to maintain 33°F (1°C) to
41°F (5°C) with pans recessed 3” (7.6cm) at 86° ambient room temperature,
meeting NSF7 requirements.
Exterior Back and Bottom are 24-gauge galvanized steel. Exterior ends are
finished with 18-gauge galvanized steel.
Base Interior has 22-gauge stainless steel back and bottom. Base interior
ends and door frames are thermoformed ABS plastic. Base is insulated with
1.5” (3.8cm) high density foamed in place polyurethane. End of base has a
machine compartment, standard on right, with condensing unit installed.
Door(s) have a 22-gauge stainless steel exterior front, with thermoformed
ABS plastic interior liner, black recessed handle and snap in magnetic gasket
which is easily replaceable. Each interior door section has (1) removable
epoxy coated wire shelf.
Refrigeration System uses HFC-404A refrigerant. Cabinet has a blower coil
assembly with expansion valve located behind door mullion. Base is equipped
with independently controlled thermostat, solenoid valve and condensate
evaporator. On/off switch for unit is located on panel above louver.
Refrigeration system in the base will maintain 36°F (2°C) to 40°F (4°C).
Unit is mounted on 6.13” (15.6cm) high adjustable stainless steel legs.
Electrical connections are 115 volt, 60 Hertz, single phase. Unit is wired
with 8’ (2.4m) cord and plug.
Model F18RC91
31.5” (80cm) Deep Self-Contained Refrigerated Reduced Height Rail
The Delfield Company, P.O. Box 470, Mt Pleasant, MI 48804-0470, U.S.A. • (800) 733-8821 • Fax (800) 669-0619 • www.delfield.com
Delfield reserves the right to make changes in design or specifications without prior notice. ©2001 The Delfield Company.All rights reserved. Printed in U.S.A.
PROJECT
ITEM #
QUANTITY DATE
APPROVAL
F18RC
®
F18RC
The Delfield Company, P.O. Box 470, Mt Pleasant, MI 48804-0470, U.S.A. • (800) 733-8821 • Fax (800) 669-0619 • www.delfield.com
Delfield reserves the right to make changes in design or specifications without prior notice. ©2001 The Delfield Company.All rights reserved. Printed in U.S.A.
31.5” (80cm) Deep Self-Contained Refrigerated Reduced Height Rail
19" (48.3cm)
19" (48.3cm)
REF'G
REF'G
1/4 HP 115V-60C-1PH
ELEVATION VIEW
F18RC52
27" (68.6cm)
REF'G
ELEVATION VIEW
14"
(35.6cm)
19" (48.3cm)
REF'G
27" (68.6cm)
REF'G
1/3 HP 115V-60C-1PH
ELEVATION VIEW
F18RC60
27" (68.6cm)
REF'G
1/2 HP 115V-60C-1PH 1/2 HP 115V-60C-1PH
18"
(45.7cm)
32" (81.3cm)
REF'G
32" (81.3cm)
REF'G
ELEVATION VIEW
F18RC72
F18RC82
14"
(35.6cm)
18"
(45.7cm)
27" (68.6cm)
REF'G
19" (48.3cm)
REF'G
27" (68.6cm)
REF'G
1/2 HP 115V-60C-1PH 3/4 HP 115V-60C-1PH
ELEVATION VIEW
F18RC91
18"
(45.7cm)
27" (68.6cm)
REF'G
27" (68.6cm)
REF'G
27" (68.6cm)
ELEVATION VIEW
F18RC99
REF'G
18"
(45.7cm)
Loading...