Delfield F17FR66 User Manual

Long Form Specifications

Top is constructed of 18-gauge stainless steel, with integral front marine edge nosing and rear backsplash. Spline bars are made of 12-gauge stainless steel and run front to back on both the left and right stainless steel sides for support and spline purposes. Interior sub-top made of 22 gauge 2BF stainless steel is made integral with the top by injecting 2.00” of high density polyurethane foam between the exterior and interior tops. As a standard 14-gauge cutting board brackets are attached to each side and house a 1.25” thick x 9.5” deep maple cutting board.

Refrigerated base interior back and bottom is constructed of 22-gauge 2BF stainless steel. Exterior sides are constructed of 18-gauge stainless steel. Bottom and back are made of 22 gauge galvanized steel. Both left and right interior sides are formed of ABS plastic. The base is injected with 2.00” of high density polyurethane foam between the exterior and interior. Refrigerated base fronts are made of .095” thick ABS thermoformed plastic and backed up by ridged polyurethane water blown injection molded frames. The frames are an excellent thermo-break and superior structural material for fastening doors and drawers. Exterior machine compartment side is constructed with 18-gauge galvanized steel.

Single units are supplied with wall-mounted bracket and threaded rod to allow installation of the unit against a solid surface. Units shipped, as part of a line-up do not come standard with a wall mounted bracket assembly.

Full Extension Plus drawer system is a complete drawer system, which can operate independent of the unit it’s installed in. Drawer system is sized to hold 12 x 20 x 4 “ deep hotel pans and smaller fractional pans. Drawer system is all stainless steel construction for maximum durability. Outer drawer track is made of 11-gauge stainless and held in place with 12-gauge up right and cross supports. Drawer track rollers are made of Delrin™ 100 NC-10 and do not require grease for operation. Intermediate tracks are removable without tools and house Delfield’s “anti-friction binary roller system”. Drawer boxes are designed with “easy pan grip flanges”. Tracks are designed with a stay shut feature that holds the drawer gasket tight to the base front on uneven floors. Exterior drawer fronts are made of 22-gauge stainless steel; and an interior made of ABS plastic with formed in channels to house the snap-in dart style santoprene gasket. A 12-gauge galvanized brace is foamed in place to be an integral part of the drawer front assembly. Each drawer front is injected with 1.87” of high density polyurethane foam between the exterior and interior. Handles are recessed black plastic and held in with a positive lock system.

PROJECT

ITEM #

QUANTITY DATE

APPROVAL

F17FR

Remote Freezer Base Equipment Stands

Model F17FR58

Unit is supported with two 14-gauge leg rails that run the entire length of the unit. Leg rails are welded to the bottom side of the unit and are tied together with two 12-gauge braces running front to back. Caster/leg boxes are welded inside the leg rail and 6.12” adjustable stainless steel legs are mounted as standard with (4) 5/16” bolts.

Remote models have a digital thermometer installed in the machine compartment (standard on right) removable access panel. Units are equipped with a thermostat, defrost timer and solenoid valve. Remote models must be hard wired at the installation site.

Freezer system components are HFC-404A. Interior cabinet is cooled with mullion style blower coils (coated) mounted between each door/ drawer section for very even air and temperature control. Electrical connections are 115V-60H-1PH.

Optional Accessories and Modifications

505B Stainless steel back

906A Stainless steel end

505F Laminate facing (drawers only)

905A Laminate back

906E Laminate end

1027A Casters

104 Doors, except 32"

108 Locks

213 *220V/50 cycle electrical * Inclusion of this option will alter electrical specifications.

The Delfield Company, 980 S. Isabella Rd., Mt Pleasant, MI 48858, U.S.A. • (800) 733-8821 • Fax (800) 669-0619 • www.delfield.com

32" (81.3cm) FRZR.

48" [121.9cm]

58" [147.3cm]

30.74"

[78.1cm]

66" [167.6cm]

76" [193cm]

9.5"

[24cm]

10"

[25.4cm]

19" (48.3cm) FRZR.

27" (68.6cm) FRZR.

[15.2cm]

ELEVATION VIEW

F17FR76

ELEVATION VIEW

F17FR48

ELEVATION VIEW

F17FR58

ELEVATION VIEW

F17FR66

PLAN VIEW

ALL MODELS

MECHANICAL ACCESS

RIGHT SIDE OF UNIT

J = JUNCTION BOX

R = REFRIGERATION LINE 1/4" LIQUID, 3/8" SUCTION

D = DRAINS 1/2"

74"

(188cm)

46"

(116.8cm)

56"

(142.2cm)

64"

(162.6cm)

F17FR

Remote Freezer Base Equipment Stands

26.08" (66.24cm)

(19", 24", 32" drawers)

28.18 (71.57cm) (27" drawers)

END VIEW

ALL MODELS

Mechanical Data–Standard Unit

MODEL NUMBER PAN* RECOM. VOLTS, HERTZ BTU DESIGN EVAP. CAP. SHIP

NUMBER OF DRAWERS CAPACITY H.P. PHASE AMPS LOAD BTU/°TD WEIGHT

F17FR48 F17FR58

F17FR66

F17FR76

*12” x 20” x 4” deep pans not included.

The Delfield Company, 980 S. Isabella Rd., Mt Pleasant, MI 48858, U.S.A. • (800) 733-8821 • Fax (800) 669-0619 • www.delfield.com

(2) 19 & (2) 27” 6 3/4 115/60/1 10.0 1461 160/17 400 lbs/ 181 kg

(2) 32” 4 1/2 115/60/1 10.0 1242 160/11 360 lbs/ 163 kg

(4) 27” 8 3/4 115/60/1 10.0 1647 160/17 475 lbs/ 215 kg

(4) 32” 8 3/4 115/60/1 10.0 1879 160/17 560 lbs/ 254 kg

30.74"

78.07cm

2.00"

5.08cm

6.13"

15.57cm

64.77cm

7.62"

19.38cm

26.00"

66.04cm

25.50"

DS17FR 04/03

36.00"

91.44cm

40.00"

101.6cm