Defi Link Display User Manual

De-Link Display Operations Manual　　　　

DF05101

This display is a valuable additional meter for providing information to automobile users about engine conditions and other important factors. When installing and operating this product, be sure to read the cautionary items of this operations manual as well as those given in the operations manual for the vehicle in which this display will be installed. Obtain a full understanding of the cautionary items and use the product accordingly. In this manual, the degree of hazard arising from actions such as improper operation is separated into the 2 levels “Warning” and “Caution.” In addition, instructions that must be followed for safe and proper use of this product as well as practices that must be maintained are marked with a “Check” heading. Please read and become familiar with these sections. In the event that this product (or the vehicle in which it is installed) is lent to or transferred to another person, please be sure this operations manual accompanies the product.

Danger

Warning

Caution

Confirmation

Before Installation (for installation personnel)

Be sure to follow all instructions in this manual to ensure safe installation and operation of the product.

Carefully consider the installation location and driver’s operation of the product before installation. Be

sure not to install the unit where it could fall. Improper installation or operation could cause the product to fall and damage the vehicle or present the severe danger of impeding driving of the vehicle.

Do not disassemble or modify this product. Such actions can not only damage or destroy the product

but will also void the warranty.

Do not perform installation of this product immediately after the engine has been switched o. The

engine and exhaust system are extremely hot at this time and can cause burns if touched.

Ensure that the wiring of this product does not have an adverse impact on the other wiring of the vehicle. The controller or

other electronic components of the vehicle could be damaged.

Please keep children and infants away from the installation area. Children may swallow small parts or be injured in other

ways.

This product is designed for use on 12V vehicles. Do not install this product on vehicles with 24V

systems.

Do not install the display in a location with much moisture or dust, or where it will be in direct sunlight,

or in an area around heater exhaust vents.

Wear gloves to avoid burns when soldering and cuts when working with wiring.

When the negative (-) battery terminal is disconnected, equipment such as clocks and audio

components having internal memory may lose their memory data. Follow the operations manual of each component to reset data after installation of this product.

After installation is complete, return this operations manual to the customer along with the warranty.

About Installation and Operation

Please have this product installed by the retail store or dealer where it was purchased. Installation by

the customer will void the warranty.

Do not disassemble or modify this product. Such actions can not only damage or destroy the product

but will also void the warranty.

In order to ensure safe driving, check the information on this display only for short periods of time.

Looking at the display for long periods of time could distract adequate attention from the road and result in an accident.

Discontinue use of this product if nothing is displayed, water gets into the unit, or smoke or a strange odor comes from the

unit. If such a condition occurs, contact the sales outlet or installation personnel as soon as possible. Continued use while the condition exists could result in an accident or re.

The De-Link Display will not operate without connection to De-Link Control Unit II or De-Link Control Unit.

When De-Link Meters or De-Link BF Meters are connected, a maximum of 7 components can be connected, including

De-Link Display.

See the De-Link System operations manual for installation of De-Link sensors.

Only the Speed Mode will be shown on the De-Link Display when no other sensors are connected to De-Link Control

Unit II or De-Link Control Unit. In that case, PEAK Mode and REPLAY Mode will not be available.

Be sure the speed signal wire is connected when using this display.

Main Features (for customer)

This product is a multi-purpose monitor for connection to De-Link Control Unit II or De-Link Control Unit. It uses an

organic light emitting diode made by Nippon Seiki.

The monitor’s display uses optimal technology for instant readability without afterimages or icker even when seen from

the passenger’s seat or in daylight.

Real-time digital information includes speed, oil temperature, water temperature, oil pressure, fuel pressure and exhaust

temperature.

Vehicle performance data and peak values are placed in memory for 3 minutes, allowing examination of data after running

the vehicle.

* De-Link Control Unit II has a 3 minute memory. De-Link Control Unit has a 40 second memory.

When the RPM signal wire is connected to De-Link Control Unit II or De-Link Control Unit, 2 warning levels can be set in

addition to the warning setting made by Control Unit II or Control Unit, enabling the setting of a total of 3 warning levels. (Tachometer Triple Warning Mode)

When the water temperature sensor is connected, the warm-up condition can be monitored.

A graphic animation plays after the ignition is turned on or o. (Opening Mode/Ending Mode)

An easily recognizable graphic on each setting screen helps guide easy setting of warnings for De-Link Meters and Step

Graph. (Setting Assistance function)

The Warning LED lights when the set warning value is exceeded for oil temperature, water temperature, exhaust

temperature and engine RPM. The Warning LED lights when measured value drops below the set warning value for oil pressure and fuel pressure.

Trouble locations are shown by graphics so that connection problems can be quickly corrected. (Self-Diagnosis function)

The structure of the mounting base allows height and angle adjustment so that it can match the shape of the instrument

panel.

The De-Link Indicator (sold separately) can be connected to the display.

indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

indicates a potential hazardous situation which, if not avoided, could result in death or serious injury.

indicates a potentially hazardous situation which not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices.

Indicates an instruction that must be performed or practice that must be maintained.

Warning

disassemble/

modify

Caution

24 V

Conrmation

(for customer and installation personnel)

Warning

disassemble/

modify

Caution

Parts List (for customer and installation personnel)

The following parts are included with this product. Conrm that all parts are present before installing the product. In addition, these parts are sold separately for part replacement, so contact your retailer for further information.

De-Link Display

Installation Stay

Meter Wire (25cm)

Speed Signal Wire (2m)

Set Screw Solderless Connector

Part Names (for customer and installation personnel)

* Organic Light Emitting Diode Display (32 x 80 Full Dot)

Warning LED

Mounting Bracket

Product Specications (for customer and installation personnel)

Power Supply Voltage 8.5 V to 13.5 VDC

(For 12 V vehicles, voltage supplied by De-Link Control Unit II or De-Link Control

Current Consumption ILM ON MAX 0.2 A

ILM OFF MAX 0.2 A

Operational Temperature Range -20 to +60 C, +14 to +140 F (under 80% relative humidity)

Storage Temperature Range -40 to +80 C, -22 to +176 F (under 80% relative humidity)

Display Range • Speedometer 0 to 400 km/h, 0 to 240 MPH

• Oil Temperature Meter 50 to 150 C, 122 to 302 F

• Water Temperature Meter 20 to 120 C, 68 to 248 F

• Oil Pressure Meter 0 to 1,000 kPa, 0 to 145 PSI

• Fuel Pressure Meter 0 to 600 kPa, 0 to 87 PSI

• Exhaust Temperature Meter 200 to 1,100 C, 390 to 2,010 F

Corresponding Speed Pulse 2, 4, 8, 16, Pulse Free

Dimensions (mm) 34 (W) x 103 (D) x 46 (H) (not including mounting base)

Gross Weight 290g, 2/3 lb (including display, wires, mounting bracket, packaging)

Troubleshooting (for customer and installation personnel)

If operation of the product seems unusual, inspect the product to conrm that it is not malfunctioning. If an operational

problem has occurred, it could result in an accident.

* In addition to a general inspection of the product, use the following table to conrm proper operation of the unit.

Condition Possible Cause Corrective Action

• Does not display.

• Triple Warning Mode cannot be set.

• Cannot adjust illumination of display.

• A line does not light in the display.

• A button does not operate.

• A dot that should not light is lighting.

• Speed is not being recorded.

QuantityPart Name

Included Parts Set for Meters

(double-sided tape, buer, mounting bracket,

M4 bolt & nut, washer)

Operations Manual

Part Name Quantity

MODE SELECT Button

SET UP

(Front Side) (Rear Side)

Button

ENTER Button

Unit.)

Set Screw

Installation Stay

Warning

• Wiring is improper.

• Display is connected to Meter Output 2 of De-Link Control Unit II.

• Display is connected to Meter Output 1 of De-Link Control Unit II.

• De-Link Display is damaged.

• The REC button of De-Link Control Unit II or REC/PLAY button of De-Link Control Unit has been pressed while the vehicle is stopped.

• Check wiring as per instructions in De-Link Control Unit II or De-Link Control Unit operations manual.

• Connect Display to Meter Output 1 of De-Link Control Unit II.

• Connect Display to Meter Output 2 of De-Link Control Unit II.

• Contact the retail outlet where the unit was purchased.

• This is normal for the product.

Press REC button or REC/PLAY button while

the vehicle is moving.

2 Pin Connector for Speed

4 Pin Connectors for Meter Wire

(Doesn't matter which is connected.)

* LICENSED PRODUCT by KODAK

Signal Wire

Installation (for installation personnel)

[Wiring Diagram]

Carefully read the “Before Installation” and “About Installation and Operation” sections of the manual concerning installation and

operation. Then install the product properly and safely.

Installation in an unsuitable location or improper installation can result in the product falling from its position or damage to the vehicle.

Warning

Installing the Mounting Bracket

1. Cut the supplied double-sided tape. [Figure 1]

2. Insert the protrusions of the mounting bracket into the slots of the meter holder, then secure with the supplied bolt and nut. [Figure 2]

3. Attach the supplied double-sided tape to the underside of the mounting bracket. Align the mounting bracket with the location for unit installation, then bend the mounting bracket to the shape of the location while pressing down so the tape will adhere. To prevent the unit from falling o, secure the mounting bracket with commercially available self-tapping screws.

* Open terminals are used for inspection of the product, so never connect wiring to these terminals. Connection to these terminals can

damage the product.

Caution

Be sure to connect the speed signal wire to this product. If the speed signal wire is not connected, the display will stay in

the Special Display Mode.

When connected to De-Link Control Unit II

The display can be connected to any of De-Link Control Unit II(see gure below), De-Link Meter and De-Link Meter BF. Switching the lighting between the daytime mode and nighttime mode is interlocked with the illumination switch of the vehicle.

Speed Signal Wire

To De-Link Indicator

Solderless Connector

Adjusting the height of the installation stay.

To Sensors

M-WARNING

Control Unit II

To P ower Source

To De-Link Meter

Meter Wire

To De-Link Meter BF

* When connected to Meter Output 1, turning the Illumination

on will reduce screen brightness by 1 level.

When connected to Meter Output 2, screen brightness can be

adjusted independently for daytime by 5 levels and nighttime

by 5 levels.

Speed signal wire of engine

computer unit of the vehicle (ECU)

ECU

Caution

When installing or working with the display, be sure to follow the applicable instructions for either De-Link Control Unit II

or De-Link Control Unit as shown in their corresponding manuals.

3 Pin Connector for

De-Link Indicator

Connector Colors

M-WARNING

Sensor Wire Installation Positions

TACHOMETER

WATER TEMP.

EXHAUST TEMP.

OIL TEMP.

FUEL PRESS.

OIL PRESS.

TURBO (BOOST)/ INTAKE MANIFOLD PRESS.

DC SOURCE

METER OUTPUT 1

METER OUTPUT 2

(white)

(blue)

(black)

(white)

(blue)

(black)

(white)

(black)

Control Unit II

(Rear Side Enlarged Diagram)

When connected to De-Link Control Unit

The display can be directly connected to either the Control Unit (see gure below) or De-Link Meters.

Control Unit

Red wire - Battery

(To 12V battery wire)

Orange wire - IGN

(To 12V wire when ignition on)

White wire - Illumination

(To 12V wire when small lamp on)

(To ground, negative battery terminal)

Black wire - GND

Control Unit II

De-Link Meter

De-Link Meter BF

To Power Source

YellowBlack

OrangeWhite

Meter Wire

White

Black

Power Wire

Meter Wires

To Sensors

Orange

Yellow

Empty

Red

Speed Signal Wire

To De-Link Indicator

To De-Link Meter

Speed signal wire of engine

computer unit of the vehicle(ECU)

White

Power Wire

Yellow

Orange

Meter Wire

Orange

Black

White

Red wire - Battery

(To 12V battery wire)

Orange wire - IGN

(To 12V wire when ignition on)

White wire - Illumination

(To 12V wire when small lamp on)

Black wire - GND

(To ground, negative battery terminal)

Orange White

Yellow Black

Solderless Connector

* When illumination is on, screen brightness will be

reduced by 1 level.

Sensor Wire Installation Positions

Control Unit (Rear Side)

Black

Orange

White

Empty

Red

Enlarged Diagram

ECU

Connector Colors

Meter Wire

TACHOMETER

WATER TEMP.

EXHAUST TEMP.

OIL TEMP.

FUEL PRESS.

OIL PRESS.

TURBO (BOOST)/ (White) INTAKE MANIFOLD PRESS.

DC SOURCE

(White)

(Blue)

(Black)

(White)

(Blue)

(Black)

(White)

[Operational Status Transition Diagram]

Illustration of set modes and functions.

[Figure 1]

[Figure 2] [Figure 3]

Conrmation

Before attaching the mounting bracket to the dashboard, thoroughly clean the mounting surface with a commercial

dashboard cleaner to remove dust, dirt and oils.

Turn the set screw to adjust position on the installation stay so the display is easy to see. (Position can shift up or down by

9.5mm.)

Max of 9.5mm up/down shift possible.

Caution

Be sure to secure the installation stay in place with the set screw.

If the screw is tightened up without the stay being placed between, it can damage the parts and cause failure of the

product.

Operation (for customer)

Opening Mode

SET UP Button

Warm-Up Mode

MODE SELECT Button

* When water temperature sensor is connected.

Gauge ModeSpeed ModeTriple Warning Mode

• Warning Settings

• Peak

• Replay

• Warning Settings

• Peak

• Replay

• Warning Settings

• Peak

• Replay

Ending Mode

After completion of Opening Mode, Warm-Up Mode elapses and the unit shifts to Triple Warning Mode/Speed Mode/

Gauge Mode. The initial setting is Gauge Mode. Each time the MODE SELECT button is pressed, the mode changes

consecutively to Gauge Mode Þ Speed Mode Þ Triple Warning Mode.

* Triple Warning Mode is not available when connected to De-Link Meter BF.

* Only Speed Mode is available if there are no sensors connected to the De-Link Control Unit II or

De-Link Control Unit. In addition, Peak Mode and Replay Mode will not function.

* Be sure to connect the speed signal wire when using this product.

Set Up Mode

Operation (for the customer)

1. Set Up Mode (Screen for setting units and display data parameters.)

Be sure to make preparatory settings. The unit will not operate properly without settings being made.

When changing the factory settings shown below, pressing the SET UP button after the Opening Mode has completed will bring up the setting mode for speed units.

Item

Speed Units

Pressure/Temperature Units

Speed Pulse

Special Display

Warm-Up

Gauge Display

Tachometer Warning 1

Tachometer Warning 2

* In Set Up Mode, the item to be set changes each time the ENTER button is pressed. When adjustment of a particular

setting is not needed, press the ENTER button to skip that item.

Speed Units Æ 2

Pressure Units Æ 3

Setting Speed Units Use the MODE SELECT button to select Speed Units, then press ENTER to set the desired units.

km/h € MPH

Setting Pressure/Temperature Units Use the MODE SELECT button to select units for the oil pressure/fuel pressure/ oil temperature/water temperature gauges, then press ENTER to set the desired units.

kPa/C € PSI/F

Setting Speed Pulse Use the MODE SELECT button to select the speed pulse number, then press ENTER to set the selection.

4 ﬁ 8 ﬁ 16 (pulse) ﬁ 2 ﬁ FREE (pulse free)

Speed Pulse Number: The speed pulse number diers by model of vehicle.Consult your local car dealer if you are not

certain of the speed pulse number for your vehicle.

Pulse Free Setting: For vehicles having a speed pulse outside 2, 4, 8, 16 pulse, the speed pulse can be set by

switching to the “Free” screen and then by pressing and holding the ENTER button while the vehicle is moving at 60 km/h or 40 MPH. After 2 seconds of holding the button, the screen will change and the speed pulse will be set.

kPa/C, PSI/F

Speed Pulse Æ 4

Press and hold

Conrmation

Setting Range

km/h, MPH

2, 4, 8, 16, FREE

ON, OFF

20 to 120C, 68 to 248F

Single, Dual

1000 to 11000 RPM

Warning 1 to 11000 RPM

Special Display Æ 5

Tachometer Warning 2 ¨ 7 Tachometer Warning 1

Display Units

km/h or MPH

kPa/C or PSI/F

—

C or F

—

RPM

Warm-Up Æ 6 Gauge Display

Factory Setting

km/h

kPa/C

4 pulse

40C

Single

7000 RPM

8000 RPM

to change units

to set the units

3. Gauge Mode

(This screen displays actual vehicle data and speed data for meters connected to De-Link Control Unit II or De-Link Control Unit.) * Does not display Turbo Meter data or Tachometer data.

O. TEMP : Oil Temperature Meter W. TEMP : Water Temperature Meter OIL P. : Oil Pressure Meter FUEL P. : Fuel Pressure Meter EXT. T. : Exhaust Temperature Meter

Press ENTER to select and adjust the displayed meter.

With the ignition on, a “　” will be displayed for meters with connected sensors. A “/” will be displayed for meters without connected sensors, and selection/adjustment will be unavailable.

1 Single Gauge Mode

Each time the MODE SELECT button is pressed, the displayed meter will change. Press ENTER to set the meter for display.

O. TEMP ﬁ W. TEMP ﬁ OIL P. ﬁ FUEL P. ﬁ EXT. T.

Normal

2 Dual Gauge Mode

With Warning generated

Warning LED

Each time the MODE SELECT button is pressed, the displayed meter will change. The upper display is set rst, then the lower display. Press ENTER to set the meter for display.

O. TEMP ﬁ W. TEMP ﬁ OIL P. ﬁ FUEL P. ﬁ EXT. T. ﬁ SPEED

* For O. TEMP, W. TEMP and EXT T. warnings, if the set warning value is exceeded for the displayed meter, the Warning

LED will light and the corresponding display value will have reverse lighting.

For OIL P. and FUEL P. warnings, if actual value drops below the set warning value, the Warning LED will light and the

corresponding display value will have reverse lighting.

Normal

With Warning generated

Warning LED

* The upper display has priority when REC, PLAY or PEAK is displayed.

4. Speed Mode (This screen displays the vehicle speed.)

Pressing the MODE SELECT button while in Gauge Mode will bring up the Speed Mode. Along with display of current vehicle speed, the maximum speed is always monitored and recorded.

Operation (for the customer)

2 When connected to De-Link Control Unit.

• REC (Recording)

Care must be used in operation because De-Link Control Unit operation diers from De-Link Display; De-Link Display determines if it should record/play according to vehicle’s running/stopped condition.

Button to Press

REAL Mode

REC/PLAY button

PEAK Mode

REC/PLAY button

Vehicle’s

Condition

Running Stopped Running Stopped

Pressing the Control Unit REC/PLAY button in either Gauge Mode, Speed Mode or Triple Warning Mode will start recording of all data for meters connected to Control Unit and speed data for a maximum of 40 seconds. When 40 seconds elapses, the unit will return to the mode used before recording started. To stop recording before the 40 second maximum elapses, press the REC/PLAY button again, and the unit will return to the mode used before recording started. Speed can be recorded during vehicle running by pressing the REC/PLAY button. * Recording of speed data will be interrupted if wiring disconnection or short circuit occurs during recording. * The unit cannot record while the vehicle is stopped even if the REC/PLAY button is pressed.

After 40 seconds

Sensor Data Connected

to Control Unit

Record Record

Play Play

Speed Data Displayed on

De-Link Display

Record

Play

Record

Play

(Record)

(Play)

9. Self-Diagnosis Function

(This screen displays serial errors, opens and shorts for each sensor of meters connected to De-Link Control Unit II or De-Link Control Unit when ignition is on. If an error message is displayed, check the item and take appropriate action.)

1 Serial Error Function

This function noties of communications that have been interrupted between the meter and the Control Unit.

2 Disconnection (Open) Check Function

This function noties that a wire disruption, disconnection or improper wiring connection has occurred at the sensor or in the sensor wire.

3 Short Circuit Check Function

This function noties that a short circuit has occurred somewhere at the sensor or in the sensor wire.

10. Opening Mode (This screen appears when the ignition is turned on.)

Factory setting is for switch to Warm-Up Mode after Opening Mode is complete.

Opening Complete

11. Ending Mode (This screen appears when the ignition is turned o.)

When connected to Meter Output 2 of Control Unit II, display of the Ending Mode screen is about 2 seconds longer than when connected to Meter Output 1 of Control Unit II or when connected to Control Unit.

* If the speed units are changed while using Pulse Free, it is necessary to repeat the pulse free

setting steps.

Setting Special Display Use the MODE SELECT button to select the special display setting, then press ENTER to set the selection.

On € O

Setting Warm-Up (only available when water temperature sensor is connected) Use the MODE SELECT button to select On or O, then press ENTER to set the selection.

On € O

used to

On selection

select used to

Warm-Up Setting

* When On is selected, each time the MODE SELECT button is pressed, the temperature value setting will increase by 1C and

each time the button is pressed and held, the value will increase by 5C. When the desired temperature value is reached, it is set by pressing the ENTER button.

Setting Gauge Display

set

Temperature Setting

pressed once raises value by 1C pressed and held raises value by 5C

used to set value

Use the MODE SELECT button to select display data format, then press ENTER to set the selection.

Single Gauge € Dual Gauge

used to select used to

Gauge Setting

Setting Tachometer Warning 1 Setting Tachometer Warning

set

Single Dual

Use the MODE SELECT button to select warning value, then press ENTER to set the value. Each time the MODE SELECT button is pressed, the value will increase by 100 RPM.

1000 ﬁ 1100 ﬁ . . . ﬁ 10900 ﬁ 11000 RPM

Each time the MODE SELECT button is pressed and held, the value will increase by 500 RPM.

1000 ﬁ 1500 ﬁ . . . ﬁ 10500 ﬁ 11000 RPM

TA Triple Warning

* Only when TA signal

is connected

WARN. 1 Lighted

pressed once raises value by 100 RPM pressed and held raises value by 500 RPM

used to set value. Then WARN. 2 will light.

* WARN. 1 setting range: 1000 to 11000 RPM * WARN. 1 factory setting: 7000 RPM

TA Triple Warning

pressed once raises value by 100 RPM pressed and held raises value by 500 RPM

used to set value. Then WARN. 1 will light.

* WARN. 2 setting range: WARN.1 WARN. 2 11000 RPM

2. Warning Setup Mode

(This screen allows setting of warnings for meters connected to De-Link Control Unit II or De-Link Control Unit.)

Item

Turbo Meter

Exhaust Temp. Meter

Oil Press. Meter

Fuel Press. Meter

Oil Temp. Meter

Water Temp. Meter

Tachometer

* Each time the WARN SET button of De-Link Control Unit II or the SELECT button of De-Link Control Unit is

pressed, the meter available for setting will change in the Warning Setup Mode.

The value of the setting is adjusted by pressing the UP button or DOWN button of De-Link Control Unit II or De-Link Control Unit. * The resolution of the UP button or DOWN button is adjusted to the analog meter. Because of the dierence in step values, the Display value changes dierently in each meter. Pressing and holding the button will accelerate the adjustment rate for easier use.

Turbo Meter Æ 2 Exhaust Temp. Meter Æ 3 Oil Press. Meter Æ 4 Fuel Press. Meter

≠ Ø

Tachometer ¨

-100 to 200 kPa or -14.5 to 29.0 PSI

200 to 1100C or 390 to 2010F

0 to 1000 kPa or 0 to 145 PSI

0 to 600 kPa or 0 to 87 PSI

50 to 150C or 122 to 302F

20 to 120C or 68 to 248F

0 to 11000 RPM

Setting Range

Water Temp. Meter ¨ 5 Oil Temp. Mete

Display Units

kPa or PSI

C or F

kPa or PSI

C or F

RPM

TURBO

5. Triple Warning Mode

(This screen displays a warning when the Tachometer exceeds the engine RPM set warning value.)

Pressing the MODE SELECT button while in Speed Mode will bring up the Triple Warning Mode when the RPM signal wire is connected to De-Link Control Unit II or De-Link Control Unit. * This mode is not available when connected to De-Link Meter BF.

When De-Link Indicator is connected, the indicator ashes being interlocked

No Warning

Under 9000RPM

Warning 1

Over 9000 RPM

Warning 2

Over 10000 RPM

The Warning LED lights up when the Tachometer exceeds the warning value set up by De-Link Control Unit II or De-Link Control Unit.

Warning LED

Warning 3

with the Warning LED.

6. REPLAY Display, PEAK Display

(This screen records vehicle data for meters connected to De-Link Control Unit II or De-Link Control Unit or it replays the recorded data or displays data peaks.) * Does not display data for Turbo Meter or Tachometer.

1 When connected to De-Link Control Unit II.

Care must be used in operation because De-Link Control Unit II operation diers from De-Link Display; De-Link Display determines if it should record/play according to vehicle’s running/stopped condition.

Button to Press

REC button

PLAY button

Vehicle’s

Condition

Running Stopped Running Stopped

Sensor Data Connected to

Control Unit II

Record Record

Play Play

• REC (Recording)

Pressing the Control Unit II REC button in either Gauge Mode, Speed Mode or Triple Warning Mode will start recording of all data for meters connected to Control Unit II and speed data for a maximum of 3 minutes. When 3 minutes elapses, the unit will return to the mode used before recording started. To stop recording before the 3 minute maximum elapses, press the REC button again, and the unit will return to the mode used before recording started. Speed can be recorded during vehicle running by pressing the REC button.

After 3 minutes

• PLAY

Pressing the Control Unit II PLAY button in either Gauge Mode, Speed Mode or Triple Warning Mode will start playing of all recorded meter data or speed data for a maximum of 3 minutes. When playing is completed, or when the PLAY button is pressed again, the unit will return to the mode used before playing started. * If PAUSE is pressed during playback, the time counter display will disappear. Speed can be played by pressing the PLAY button when the vehicle is stopped. If PAUSE is pressed during speed playback, the unit will return to Real Mode.

After 3 minutes

• PEAK Display

Pressing the Control Unit II PEAK button in either Gauge Mode, Speed Mode or Triple Warning Mode will display recorded peak values from all meter data or speed data. Pressing the PEAK button again will return the unit to the mode used before peak display started. Pressing the UP button of Control Unit II while a peak value is displayed will reset the peak value.

Peak Peak Reset

Speed Data Displayed on

De-Link Display

Record

Play

Record

Play

(Record)

(Play)

• PLAY

After recording, pressing the Control Unit REC/PLAY button when PEAK values are being displayed will start playing of all recorded meter data or speed data for a maximum of 40 seconds. When playing is completed, or when the REC/PLAY button is pressed again, the unit will return to the mode used before playing started. Speed can be played by pressing the REC/PLAY button while in PEAK Mode when the vehicle is stopped. If PAUSE is pressed during speed playback, the unit will return to Real Mode. * Recording of speed data will be interrupted if wiring disconnection or short circuit occurred during recording. * The unit cannot play while the vehicle is running even if the REC/PLAY button is pressed.

After 40 seconds

* If PAUSE is pressed during playback, the time counter display will disappear.

• PEAK Display

Pressing the Control Unit PEAK/RESET button in either Gauge Mode, Speed Mode or Triple Warning Mode will display recorded peak values from all meter data or speed data. Pressing the PEAK/RESET button again will return the unit to the mode used before peak display started. Pressing the Control Unit PEAK/RESET button for 2 seconds while a peak value is displayed will reset the peak value.

Peak Peak Reset

7. Special Display Mode

(This screen is displayed when speed is 0 Km/h or 0 MPH for more than 10 seconds.)

* Turbo Meter and Tachometer are not displayed.

When Special Display is turned on in Set Up Mode, the peak values for meters having connected sensors are displayed from the time ignition is on while in Gauge Mode or Speed Mode.

When Special Display is turned o in Set Up Mode, the digital display disappears and the Warning LED ashes at a steady interval.

Warning LED

Steady Flash

8. Warm-Up Mode

* If the Warning LED is lighted while in Gauge Mode, the Special Display Mode cannot be

activated.

(This screen monitors water temperature until it reaches a set value.)

When Warm-Up is turned on in Set Up Mode and the water temperature sensor is connected to Control Unit II or Control Unit, the Warm-Up Mode activates after Opening Mode is completed. The “Warm-up” notice and current water temperature are displayed until the temperature reaches the set value. When the temperature reaches the set value, the warm-up completed “Ready” notice is displayed for 5 seconds and the unit returns to the display mode used before the ignition was turned o (Speed Mode, Gauge Mode or Triple Warning Mode). Factory setting is Gauge Mode.

* REC, PLAY and PEAK display cannot be used during

Warm-Up Mode.

Warm-Up CompletedDuring Warm-Up

Water temperature of 20C (68F) or below is displayed as “ - - -”.

If the MODE SELECT button or SET UP button is pressed before water temperature reaches the set value, the unit will switch to the other mode (except for Warning Setup Mode or Set Up Mode) and a “C” symbol will appear in the upper left corner of the screen until the temperature reaches the set value.

Displaying Oil Press./Water Temp.Displaying Speed

* REC, PLAY and PEAK display can be used while the “C” symbol is displayed.

Optional Parts (for customer)

De-Link Indicator Model number DF01801

The indicator ashes red when a meter being displayed on the De-Link Display reaches the set warning value.

[Indicator Installation Method (for installation personnel)]

• When used as an indicator for a connected meter.

1. Attach the supplied double-sided tape to the bottom of the indicator body. (Attach 2 layers of double-sided tape for ø4 1/8" (80 mm) or ø4 1/2" (115 mm) size meters.)

2. Connect the supplied wire.

3. Attach the Indicator to the meter or the instrument panel.

De-Link Sensor Set

Sensor sets include the meter sensor and sensor wire for connection to De-Link Control Unit II or De-Link Control Unit. If one of the following sensor sets is connected to De-Link Control Unit II or De-Link Control Unit, De-Link Display can be used for displaying values even without a meter.

Item

De-Link OIL PRESS. Sensor Set

De-Link FUEL PRESS. Sensor Set

De-Link OIL TEMP. Sensor Set

De-Link WATER TEMP. Sensor Set

De-Link EXHAUST TEMP. Sensor Set

Model Number

PDF00713SS

PDF00806SS

PDF00908SS

PDF01006SS

PDF01114SS

Double-sided tape

02.9-0.3k

wire

Defi Link Display User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual