Page 1
INSTALLATION INSTRUCTIONS
3" BULL BAR
2014 CHEVY SILVERADO1500/GMC SIERRA1500
Page 2
3" BULL BAR
Qty
Description
Qty
Description
1
Bull Bar
4
10-1.50mm x 30mm Hex Bolt
1
Driver/Left Mounting Bracket
14
10mm x 27mm OD x 3mm Flat Washer
1
Passenger/Right Mounting Bracket
10
10mm Lock Washer
2
10-1.50mm x 30mm Double Bolt Plates
10
10-1.50mm Hex Nut
2
10-1.50mm x 35mm Bolt Plates
Passenger/Right Frame
Mounting Bracket
Driver/Left Frame
Mounting Bracket
(2) 10mm x 35mm
Bolt Plates
(2) 10mm x 30mm
Double Bolt Plates
2014 CHEVY SILVERADO1500/GMC SIERRA1500
PARTS LIST:
PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY BEFORE STARTING INSTALLATION. CUTTING IS REQUIRED.
2. NOTE: It may be necessary to remove/relocate front license plate and license plate bracket. It is not
required, but strongly recommended. If local/state law requires a license plate, a license plate
relocation kit is available.
3. Start installation from under the front of the vehicle. Determine if the vehicle is equipped with tow
hooks.
Tow Hook equipped vehicles:
a. Remove the steel bumper and brackets to access the hardware securing the tow hook to the
frame channel.
b. Remove the factory tow hook from the end of each frame channel, (Figure 1). NOTE: This Bull
Bar is not compatible with tow hooks.
c. Cut out the opening in the plastic bumper insert to clear the Mounting Brackets, (Figure 1).
d. Reinstall the bumper after tow hooks have been removed and the openings have been cut out
and checked for clearance.
Vehicles without tow hooks:
a. Cut out the indented area in both sides of the plastic bumper insert to clear the Brackets as
pictured, (Figures 1 & 2). IMPORTANT: Make several small cuts for best fit. Do not cut through
the top edge of the panel. NOTE: The plastic panel is held in place with several small screws
that are difficult to reach and remove. If you prefer to remove the panel to cut out the openings,
it may be necessary to remove the steel bumper to access all of the small screws and clips.
b. Reinstall the bumper once openings have been cut out and checked for clearance.
4. Select the driver side Mounting Bracket. Insert the Bracket through the opening in the plastic bumper,
(Figure 3). Line up the (3) holes in the Bracket with the holes in the end of the frame channel.
5. Select the 10mm Double Bolt Plate, (Figure 4A). Insert the Bolt Plate into the end of the frame channel,
through the holes in the Bracket and out the side of the frame. Secure the Bolt Plate to the Brackets
with (2) 10mm Flat Washers, (2) 10mm Lock Washers and (2) 10mm Hex Nuts, (Figure 4B). Leave
loose at this time. Repeat this Step to install the 10mm x 35mm Bolt Plate, (Figure 5A), into the
remaining hole in the side of the Bracket and frame channel, (Figure 5B).
Page 1 of 3 7/10/13 (DP)
Page 3
6. Repeat Steps 4 & 5 to install the passenger side Mounting Bracket. If the bumper was removed, align
(Fig 2) Dotted line on Silverado
bumper pictured for example only
(Fig 1) Sierra pictured for example only
(Fig 3) Driver side of Silverado pictured without
plastic cover for instructions purposes only
7-1/2"
10mm Bolt Plate
10mm Double Bolt Plate
2-1/2"
Cut out area illustrated for example only. Due to
different models and options, actual area
required for bracket clearance to be determined
by installer. Start with a small opening and
enlarge until proper clearance for best results.
Do not cut through
top edge of panel
the bumper to the vehicle and tighten all factory hardware.
7. With assistance, position the Bull Bar up to the outside of the Mounting Brackets. Bolt the Bull Bar to
the Mounting Brackets using (4) 10mm x 30mm Hex Bolts, (8) 10mm Flat Washers, (4) 10mm Lock
Washers and (4) 10mm Hex Nuts, (Figure 6).
8. Align and adjust the Bull Bar and tighten all hardware.
9. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer
over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish.
For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap may be
used also to clean the Bull Bar.
For gloss black finishes: Mild soap may be used to clean the Bull Bar.
Driver Side Installation Pictured
3" BULL BAR
2014 CHEVY SILVERADO1500/GMC SIERRA1500
Page 2 of 3 7/10/13 (DP)
Page 4
3" BULL BAR
Fig 4B
Fig 4A
Fig 5B
(2) 10mm x 30mm Hex
Bolts
(4) 10mm Flat Washers
(2) 10mm Lock Washers
(2) 10mm Hex Nuts
Fig 5A
Fig 6
10mm Flat Washer
10mm Lock Washer
10mm Hex Nut
(2) 10mm Flat Washers
(2) 10mm Lock Washers
(2) 10mm Hex Nuts
Complete Installation
2014 CHEVY SILVERADO1500/GMC SIERRA1500
Driver Side Installation Pictured
Page 3 of 3 7/10/13 (DP)
Loading...