Dee Zee DZ372211 User Manual
(W)
INSTALLATION INSTRUCTIONS
3" ROUND & 4" OVAL SIDEBAR (90-DEG BENT END)
DODGE RAM 2500/3500 REG. CAB 10-12 / RAM 1500 REG. CAB 09-12
PART # DZ 372211/DZ 372212/DZ 372213
Qty
Description
Qty
Description
1
Driver/Left Sidebar
4
1/2” X 1-1/2” OD x 1/8" flat washers
1
Passenger/Right Sidebar
4
12mm x 35mm Bolt/10mm Nut Plates
1
Driver/Left Front Mounting Bracket
2
12mm x 40mm Bolt Plates
1
Passenger/Right Front Mounting Bracket
6
12mm x 32mm OD x 3mm Flat Washers
1
Driver/Left Front Support Bracket
6
12mm Lock Washers
1
Passenger/Right Front Support Bracket
6
12mm Hex Nuts
1
Driver/Left Rear Mounting Bracket
6
12mm Plastic Retainers
1
Passenger/Right Rear Mounting Bracket
4
10-1.50mm x 35mm Hex Bolts
4
1/2” x 2” Hex Bolts
4
10mm x 30mm OD x 2.5mm flat washers
4
1/2” Lock Washers
4
10mm Lock Washers
Passenger Side
Rear Mounting
Bracket
Passenger
Side Front
Mounting
Bracket
Driver Side
Rear
Mounting
Bracket
Driver Side
Front
Mounting
Bracket
12mm x 35mm Bolt/10mm Nut
Plate (pictured with Plastic
Retainer installed for example)
12mm x 40mm Bolt Plate
(pictured with Plastic
Retainer and hardware)
Passenger Side Front
Support Bracket
Driver Side Front
Support Bracket
Passenger/Right Sidebar
Driver/Left Sidebar
Front of Sidebar
PARTS LIST:
PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY BEFORE STARTING INSTALLATION.
2. Starting at the passenger side-front of the vehicle, remove the tape covering the factory oval holes in
the inner body panel located by the front tire.
3. Select (1) 12mm Bolt Plate and partially thread a Plastic Retainer onto it, (Fig 1A). Insert the Bolt Plate
into the oval hole, (Fig 1B). Once the Bolt Plate is inserted, hold the Bolt end with one hand and tighten
the Plastic Retainer with your other hand until it is tight against the body panel. IMPORTANT: The
Plastic Retainer is designed to prevent the Bolt Plate from falling into the body cavity and to aid in
installing the Mounting Bracket.
4. Next, partially thread a Plastic Retainer onto the threaded end of a Bolt and Nut Plate, (Fig 1C).
Insert the Bolt and Nut Plate with Plastic Retainer into the factory oval hole, (Figure 1B).
5. Select the passenger side front Mounting Bracket. Position the Mounting Bracket onto the (2) Bolt
Plates. Secure the Bracket to the Bolt Plates with (2) 12mm Flat Washers, (2) 12mm Lock Washers
and (2) 12mm Hex Nuts, (Figure 2). Do not tighten at this time. Rotate the Bolt and Nut plate until the
threaded Nut end lines up with the remaining hole in the Mounting Bracket and body. Thread (1) 10mm
x 35mm Hex Bolt, (1) 10mm Flat Washer and (1) 10mm Lock Washer into the threaded nut plate. Snug
but do not tighten hardware at this time.
6. Remove the passenger side front factory body bolt. Select the passenger side Front Support Bracket.
Page 1 of 3 1/12/09 Rev 1(DP)
Insert the factory body bolt through the Support Bracket and up into its original position, (Figure 2).
3" ROUND & 4" OVAL SIDEBAR (90-DEG BENT END)
DODGE RAM 2500/3500 REG. CAB 10-12 / RAM 1500 REG. CAB 09-12
Loading...