Deep SEA Electronics 7560 User Manual

ACCESSING THE FRONT PANEL CONFIGURATION EDITOR

.

•

EDITING A PARAMETER

Deep Sea Electronics Plc.

Web:

www.deepseaplc.com

Deep Sea Electronics inc.

Deep Sea Electronics Plc.

TYPICAL WIRING DIAGRAM

DEEP SEA ELECTRONICS

7560 I NS TALL AT ION INSTR UC TI ON S

• Press the Stop/Reset and Info buttons simultaneously.

• If a module security PIN has been set, the PIN number request is then

shown :

053-054

ISSUE 4

Tel:[phone]

Fax: [phone]

LO CALL (from UK BT landlines) :

Telephone [phone]

Email: [e-mail]

Phone: [phone]

Fax: [phone]

TOLL FREE (USA only) : Tel: [phone]

Email: [e-mail]

Web: www.deepseausa.com

(Far East)

Tel:[phone]

Fax: [phone]

Email: [e-mail]

Web: www.deepseaplc.com

• Press

• Press (right) when the first digit is correctly entered. The digit you have just entered will now

show ‘#’ for security.

•

Repeat this process for the other digits of the PIN number. You can press
move back to adjust one of the previous digits.

•

When is pressed after editing the final PIN digit, the PIN is checked for validity. If the number is
not correct, you must re-enter the PIN.

(up) or

(down) to adjust it to the correct value.

(left) if you need to

If the PIN has been successfully entered (or the module PIN has not been
enabled), the editor is displayed :

• Enter the editor as described above.

• Press the left or right buttons to cycle to the section you wish to view/change.

• To edit the parameter, press to enter edit mode. The parameter begins to flash to indicate that

you are editing the value.

• Press the up or down buttons to change the parameter to the required value.

• Press to save the value. The parameter ceases flashing to indicate that it has been saved.

• To exit the editor at any time, press the button.

NOTE: When the editor is visible, it is automatically exited after 5 minutes of inactivity to
ensure security.
NOTE: The PIN number is automatically reset when the editor is exited (manually or
automatically) to ensure security.
NOTE: More comprehensive module configuration is possible using the 75xx series PC
configuration software. Please contact us for further details
NOTE: The contents of the tables overleaf may differ depending on the actual module
configuration.

ADJUSTABLE PARAMETERS.

Section

Parameter

as shown on

Values

Timers

Mains

System

Misc

AC System

3 phase 4 wire

3 phase 4 wire3 phase 4 wire

3 phase 4 wire

0.1%-100% (

2.0%)

2.0%)2.0%)

2.0%)

ACCESSING THE ‘RUNNING’ CONFIGURATION EDITOR

EDITING A PARAMETER

Voltage adjust

Frequency adjust

DIMENSIONS

PANEL CUTOUT

Front Panel Configuration Editor

Mains Transient Delay

Start Delay

Transfer Delay

Return Delay

Low battery Delay

High battery Delay

Mains Under Voltage Alarm 50V-360V ph-N (184V)

Mains Over Voltage Alarm 50V-360V ph-N (276V)

Mains Under Frequency 0Hz-75Hz (45Hz)

Mains Over Frequency 0Hz-75Hz (55Hz)

Plant Battery Under Volt Alarm 0-40V (10V)

Plant Battery Over Alarm 0-40V (30V)

Language English, Other

Alternative Frequency Enable Disable

Alternative Voltage Enable Disable

Contrast

Date and Time dd mmm yyyy hh:mm

Auto Scroll Time 0-10s (2s)

Mains CT Primary Rating 5A- 6000A (600A)

Mains CT Secondary Rating 1A, 5A (5A)

Load Ramp Rate

(Factory default settings are shown in bold italicised text)

0 -10s (2s)
0– 60m (5s)

0– 10s (0.7s)
0– 60m (30sa0
0– 10m (1m)

0– 10m (1m)`

(10V)

(10V)(10V)

(30V)

(30V)(30V)

Single phase 2 Wire
3 phase 3 wire
2 phase 3 wire L1 & L2
3 phase 4 wire ED
2 phase 3 wire L1 & L3

 l 

(2s)

(2s)(2s)

(% per sec)

(184V)

(184V)(184V)

(276V)

(276V)(276V)

(45Hz)

(45Hz)(45Hz)

(55Hz)

(55Hz)(55Hz)

Disable

DisableDisable

Disable

DisableDisable

(600A)

(600A)(600A)

(5A)

(5A)(5A)

• The ‘running’ editor can be entered while the engine is running. All protections remain active if the
engine is running while the running editor is entered.

• Press and hold the button to enter the running editor.

• Enter the editor as described above.

• Press the left or right buttons to cycle to the section you wish to view/change.

• Press the up

• To save paremeters scroll to `save changes and exit followed by the down buttton

• To cancel changes scroll to `Abandon changes and exit followed by the down

button

or down

buttons to change the parameter to the required value.

ADJUSTABLE PARAMETERS (Running editor)

Running Editor

Section Parameter as shown on display

DISPLAY Contrast

Language

Load power factor

Load parallel power

Enable commissioning screens

(manual mode only engine running bus breaker open)

(manual mode only engine running bus breaker open)

Enable mains decoupling

Abandon changes and exit

Save changes and exit

Factory Settings

 l 

English
%
%
No
Raise Steady Lower
Raise Steady Lower
No

240.0mm x 181.1mm x 41.7mm (9.4” x 7.1” x 1.6”)

:

220mm x 160mm (8.7” x 6.3”)