Deep SEA Electronics 710 User Manual

(

TYPICAL WIRING DIAGRAM

DEEP SEA ELECTRONICS

053-013 ISSUE 1

Model 710 Configuration and installation instructions

ACCESSING THE CONFIG EDITOR

Press the Stop/Reset

and Info buttons

simultaneously.

• The LED beside the AUTO button will flash continuously to indicate that configuration mode has been entered.

• The first configuration

setting is displayed:

From the configuration table, this example is displaying Start Delay (parameter 0). It is currently set to 5 seconds.

EDITING A PARAMETER

• Enter the editor as described above.

• Press + / - to scroll through the parameters to

the one you want to change.

• Press 9 to enter edit mode. The

will flash on the display to indicate that edit mode has been entered.

• Press + / - to change the value to the desired parameter.

• Press 9 to save the value and exit edit mode for this parameter.

• The symbol will be removed from the display to indicate that edit mode has been exited.

• To select another value to edit, press the + / buttons. Continuing to press the + and – buttons will cycle through the adjustable parameters as shown in the following lists.

symbol

SETTINGS

Factory default settings are in bold italicised text.

Timers

0 - Start Delay 0-60m (5s) 1 - Preheat 0-60s (0s) 2 - Cranking Time 3-60s (10s) 3 - Crank Rest Time 3-60s (10s) 4 - Safety On Delay 8-60s (8s) 5 - Warm Up Time 0-10m (0s) 6 - Gen transient delay 0-10s (0s) 7 – Return Delay 0-60m (30s) 8 - Cooling Time 0-30m (1m) 9 - ETS Hold Time 0-60s (0s) 10 - Fail To Stop Delay Time 10-60s (60s) 11 - Low DC Voltage Alarm Delay 0-60m (5m)

NOTE:- Setting a timer to 0 will disable it (where applicable)

Generator

12 - Under Frequency 0-60Hz (40Hz) 13 - Loading Frequency 20-60Hz (47Hz) 14 - Over Frequency 50-72Hz (57Hz) 15 - Loading Voltage 50-333V (212V) 16 - Over Current Alarm 50-120% (110%) 17 - Over Current Alarm Type 0 - Warning 1 - Shutdown 2 - Electrical Trip

Engine

18 - Low DC Voltage Alarm 0-25V (8V) 19 - Charge Fail Voltage Alarm 0-25V (8V)

Fixed Input settings

20 - Low Oil Pressure 5-150PSI (15 PSI) 21 - High Engine Temperature 22 - Remote Start input 0 - Remote start

90-150°C

close to activate

1 - Remote start,

open to activate

95°C)

NOTE: To exit the front panel configuration editor at any time, press the Stop/Reset button.

Ensure you have saved any changes you have made by pressing the 9 button first

Deep Sea Electronics Plc.

Highfield House, Hunmanby Industrial Estate,

North Yorkshire. YO14 0PH. ENGLAND

Tel:+44 (0)1723 890099.

Fax: +44 (0)1723 893303.

Email: sales@deepseaplc.com

Web: www.deepseaplc.com

Deep Sea Electronics inc.

3230 Williams Avenue

Rockford, IL 61101-2668. U.S.A.

Phone: +1 (815) 316-8706

Fax: +1 (815) 316-8708

Email: dsesales@deepseausa.com

Web: www.deepseausa.com

DIMENSIONS

MOUNTING

PANEL CUT-OUT

209mm x 146mm (8.23” x 5.75”)

Mounting holes suitable for 4 x 4mm screws Mounting Hole spacing 196.0mm x 103.5mm (7.717” x 4.075”)

182mm x 137mm (7.17” x 5.39”) Maximum panel thickness – 8mm (0.3”)

Factory default settings are in bold italicised text.

Auxiliary Input settings

23 - Input 1 0 - Delayed, warning, close to activate 2 - Immediate, warning, close to activate

3 - Immediate, warning, open to activate 4 - Delayed, shutdown, close to activate 5 - Delayed, shutdown, open to activate 6 - Immediate, shutdown, close to activate 7 - Immediate, shutdown, open to activate 8 - Lamp test, close to activate 9 - Lamp test, open to activate 24 - I/P 1 delay 0-10s (0s) 25 - Input 2 0 - Delayed, warning, close to activate

2 - Immediate, warning, close to activate 3 - Immediate, warning, open to activate 4 - Delayed, shutdown, close to activate 5 - Delayed, shutdown. Open to activate 6 - Immediate, shutdown, close to activate 7 - Immediate, shutdown, open to activate 8 - Electrical trip, close to activate 9 - Electrical trip, open to activate 26 - I/P 2 delay 0-10s (0s)

1 - Delayed, warning, open to active

Outputs

27 - Output 1 0 - Unused 2 - Air Flap

3 - Close Generato 4 - Energise to sto 5 - Engine Runnin 6 - Shutdown Alarm 7 - System in auto 8 - Auxiliary input 1 active 9 - Auxiliary input 2 active 10 - Preheat mode 1 11 - Preheat mode 2 12 - Preheat mode 3 13 - Warning Alarm 14 - Common Alarm 15 - Fail to start 28 - Output 2 0 - Unused

2 - Air Flap 3 - Close Generato 4 - Energise to sto 5 - Engine Runnin 6 - Shutdown Alarm 7 - System in auto 8 - Auxiliary input 1 active 9 - Auxiliary input 2 active 10 - Preheat mode 1 11 - Preheat mode 2 12 - Preheat mode 3 13 - Warning Alarm 14 - Common Alarm 15 - Fail to start

1 - Preheat Mode 0

Outputs cont’d

29 - Output 3 0 - Unused

1 - Preheat Mode 0 2 - Air Flap 3 - Close Generator 4 - Energise to stop 5 - Engine Running 6 - Shutdown Alarm 7 - System in auto 8 - Auxiliary input 1 active 9 - Auxiliary input 2 active 10 - Preheat mode 1 11 - Preheat mode 2 12 - Preheat mode 3 13 - Warning Alarm 14 - Common Alarm 15 - Fail to start 30 - Output 4 0 - Unused

LCD Indicators

31 - Indicator 1 0 - Unused

Factory default settings are in bold italicised text.

LCD Indicators cont’d

32 - Indicator 2 0 - Unused

Misc

35 - Full Load Current Rating 36 - Current Transformer Primary 37 - Alternator Poles 2,4,6,8 (4) 38 - AC Topology 0 - 3 phase, 4 wire

39 - Oil Pressure Display Units

40 - Oil pressure sender type 1 - Digital closed for low oil

2 - Digital open for low oil 3 - VDO 5 bar

4 - VDO 10 bar 5 - Datcon 5 bar 6 - Datcon 10 bar 7 - Datcon 7 bar 8 - Murphy 7 bar 9 - User configured 41 - Coolant temperature sender type 2 - Digital open for high

4 - Datcon high 5 - Datcon low 6 - Murphy 7 - Cummins 8 - PT100 9 - User configured

NOTE:- The ‘preheat modes’ selectable for configurable outputs and LCD indicators perform the following actions :

• Preheat mode 0 - Preheat during preheat timer,

ceasing at end of preheat timer.

• Preheat mode 1 - Preheat during preheat timer

and continue until engine stops cranking.

• Preheat mode 2 - Preheat during preheat timer

and continue until the safety delay timer has expired.

• Preheat mode 3 - Preheat during preheat timer

and continue until the warming timer has expired.

In addition, in all preheat modes, preheat takes place during the crank rest timer between crank cycles.

5-6000A (500A) 10-6000A (500A)

1 - Single phase, 2 wire

0 - Bar / PSI

1 - Kpa

0 - Not used

pressure pressure

1 - Digital closed for high temperature

temperature 3 - VDO 120