DCS ADR236, BCBOTTLEAC25, DP142, ADR248, ADR230 Quick Guide
QUICK START GUIDE
Outdoor Kitchen Storage solutions
US CA NZ AU
Keep this document handy for easy reference.
Before using your product, make sure you read the full ‘Quick Start guide’, with special attention to the ‘Safety and warnings’ section.
For contact information or if you require service, assistance or replacement parts, see the end of this document or your ‘Service & warranty’
booklet.
SAFETY AND WARNINGS
WARNING!
Cut hazard
Take care - panel edges are sharp.
Failure to use caution could result in injury or cuts.
WARNING!
Crush hazard
Closing drawers may cause injury to your hands or
fingers.
Always close or open drawers using their handles.
Be sure to keep hands away from drawer edges when
opening or closing drawers.
Failure to use caution could result in injury or cuts.
IMPORTANT SAFETY INSTRUCTIONS!
Do not allow children or pets to play in or around your outdoor
accessories. Children could be seriously injured if they climb onto or into
these products.
DANGER: Risk of child entrapment. Before you throw away your old
pantry:
- take off the doors
- leave the shelves and drawers in place so that children may not easily
climb inside.
MODEL OVERVIEW
Children, or persons with a disability which limits their ability to
use the appliance, should have a responsible person to instruct
them in its use. The instructor should be satisfied that they can use
the appliance without danger to themselves or their surroundings.
To avoid personal injury or damage to the products, do not
overload the drawers or shelves. The maximum allowable weight
for a drawer is 75 lbs / 35 kg.
Your pantry and drawer units are not refrigerated. Do not store
perishable foods in them.
Ensure your beverage chiller has been correctly installed and
connected to a drainage system.
Do not store or use gasoline or other flammable vapors and liquids
inside or in the vicinity of these or any other appliances.
An LP cylinder not connected for use shall not be stored inside or in
the vicinity of these products.
After having unpacked the appliance, check to ensure that it is not
damaged.
Packing elements (eg plastic bags, polystyrene foam, nails, packing
straps, etc.) should not be left around within easy reach of children, as
these may cause serious injuries.
Follow the installation instructions. The manufacturer is not
responsible for any damage or defects arising from improper
installation.
Some products are supplied with protective film on steel and alumini-
um parts. This film must be removed before using the appliance.
Do not modify this appliance.
PANTRY ARRANGEMENT (DP42 ONLY)
Important!
Letting the pantry door open more than 105 degrees
could result in marking of the outer surface finish
Please exercise caution when opening the door and
make sure that is is not opened more than 105
degrees.
Shelves
There is a choice of 3 positions for the two supplied shelves.
Drawers
The drawer inserts are removable for ease of
cleaning.
To remove:
Open the drawer fully and carefully lift out the insert.
You may also remove the entire drawer if required.
See ‘Removing and replacing drawers’
WASTE BASKET (TB1-20 ONLY)
Important!
Do not use force to compact down trash as this may
damage the drawer glides.
The maximum total weight the waste baskets can hold
is 35 lbs / 16 kg each.
To avoid personal injury, caution should be used when lifting
full trash bins.
The drawer is soft closing, which requires less force to close.
BEVERAGE CHILLER (BC25 ONLY)
The condiment tray sits in the chiller as shown.
The four individual containers and lids may be
removed for cleaning / filling.
Condiment Trays
TDS1-20
TDD1-20
DRAWERS
TDT1-20
WASTE BASKET BEVERAGE CHILLER
TB1-20
PANTRY
DP1-42
BC25
BOTTLE HOLDER
BC-BOTTLEAC-25
Beverage chiller lid
Ensure the lid sits level and secure on top of the chiller.
The side of the lid with the shorter lip fits on the front
of the beverage chiller. This allows the lid to sit flat if
the bottle holder* is installed.
Drainage
We recommend plumbing your Beverage Chiller into
a permanent drainage system. The connection to
the drainage system must be made by a certified
plumber and compliant with local and national code
requirements.
New Zealand & Australia only:
Use the supplied drain adapter to plumb the chiller.
*Bottle holder (optional)
The bottle holder is permanently fitted to the front of
your beverage chiller. It comes with a removable drip
tray for ease of cleaning.
*purchased separately. Contact Customer Care or your
Authorised DCS dealer; part no 71036.
BEVERAGE CHILLER
BOTTLE HOLDER
REMOVING DRAWERS (SOME PRODUCTS ONLY)
CARE AND CLEANING
To remove the drawer(s)
1
Remove the drawers by pulling them
out until the slider latch is visible.
2
Carefully push the latch down on the
left side, while lifting up the latch on
the right side.
3
Pull the drawer out of the frame.
Note: to prevent damage to surfaces, place
the drawers on a stable surface on a
protective towel or table cloth.
REPLACING DRAWERS (SOME PRODUCTS ONLY)
To replace the drawer(s)
1
Extend both guide rails out.
2
Engage the drawer rails into the guide
rails. Pull the guide rails forward until
they ‘click’ into place.
3
Push the drawer all the way in (there
will be some resistance) to completely
engage the drawer.
Note: drawers in all products except
for the pantry unit are “soft closing”.
Extend guide rails Engage drawer rails
Left Slider latch
Right Slider latch
Important!
Do not use abrasive cleaners, steel soap pads or sharp objects on
stainless steel.
Note: Stainless steel tends to corrode in presence of chlorides and
sulfides especially in coastal areas. To ensure corrosion prevention,
wash all stainless steel surfaces every 3-4 weeks with fresh water and
stainless cleaner.
These stainless steel products are made of mold resistant materials.
However, to avoid staining or growth of mold, always empty, clean and
dry your product(s) when not in use.
Always use the mildest cleaning procedure first.
Wipe soiling off with a cloth using a mild household detergent and
wipe dry with a clean cloth.
Regularly clean the drawers using hot soapy water. Rinse and dry with
a clean soft cloth to avoid water marks.
To maintain the exterior appearance, apply a stainless steel polish to
the outside surfaces on a regular basis.
Always read the label of your stainless steel cleaner to ensure it does
not contain chlorine compounds.
Always rub the stainless steel in the direction of the grain.
FOR MORE INFO
For warranty information
If you…
have any questions or comments
need a DCS by Fisher & Paykel authorized
technician to service your product
need replacement parts or accessories
want to register your product
see your ‘Service and warranty’ booklet
see your ‘Service and warranty’ booklet or contact us
USA
toll-free, 24/7
www.dcsappliances.ca
Drawer maintenance
To maintain the smooth operation of the drawers, spray the bearing
areas with silicone spray lubricant annually.
Lubrication points
(use silicone spray
annually)
1 888 936 7872 www.dcsappliances.com
NZ
0800 372 273 www.fisherpaykel.co.nz/customercare
www.dcsgrills.co.nz
AU
1300 650 590 www.fisherpaykel.com.au/customercare
www.dcsgrills.com.au
590616C 03.15
Loading...