Other Davis Boat Pole Accessories:
#5141
®
REPLACEMENT BOAT HOOK KIT
BOAT HOOK END ONLY
A direct replacement for all Davis and Davis Team® boat hooks.
Also fits EEz-In
diameter, .035" wall thickness (2.5 and 3.2 cm dia., .89 mm wall).
The World's Strongest Boat Hook End!
®
boat hooks and others using tubing 1" and 11/4"
THREADED DECK BRUSH
Fits Team Boat Hook. Extra long
synthetic bristles resist most
cleaning chemicals. 8 × 21/2"
(20.3 × 6.3 cm). #R5120
THREADED DECK MOP
Fits Team Boat Hook. Super
absorbent. Rot and mildew
resistant. #R5123
3/4" (19 mm) Acme Thread
accepts brushes, mops, etc.
Extra Thick Neck
and Body add to
durability.
Ribbed Hook and Unbreakable
® —
Lexan
than (brittle) metal alloy ends.
All Team® boat hooks float!
tougher by design, lighter
Bright Orange Vinyl Tip
protects boat's finish, aids visibility
and eye-hand coordination.
Hole Molded in Tip for securing
hook or attaching small line for use
with tarps or awnings.
Curved Head
for fending off stanchions
and lines.
3465 Diablo Ave., Hayward, CA 94545 U.S.A.
(510) 732-9229 • (510) 732-9188 Fax
info@davisnet.com www.davisnet.com
05141.050, Rev. D April 2008
INSTALLATION
INSTRUCTIONS
Use method appropriate for
your type of original pole.
REPLACEMENT KIT INCLUDES:
Boat Hook
Tip
METHOD A
Plastic
Adapter
Sleeve
Stainless Steel
Drive Rivets
Davis w.
black hook
®
EEz-In
METHOD B
All Davis and Team® products with
with black plastic hook
With Davis Versapoles™ this method
is a permanent replacement.
For a removable replacement boat hook,
contact Davis Customer Service
at 800-678-3669.
All EEz-In® boat hooks
with grey metallic-looking hooks
on 1" (25.4 mm) diameter poles
All Davis and Team® boat hooks and
paddle boat hooks
Davis w.
white hook
with white plastic hook
1. Using a pliers or “vise-grip” tool, remove both
drive screws securing the old boat hook tip.
Tightly grip the sides of the drive screws before
turning them counter-clockwise.
If, for some reason, you cannot get a good
grip to back them out, try Method B.
2. Pull out stub of broken boat hook tip.
3. If telescoping pole:
Insert new boat hook tip into the adapter sleeve
and then insert both into tube.
If fixed length pole:
Insert new boat hook tip directly into tube.
4. Using a #24 or 5/32" (4 mm) drill bit, drill a hole through each
old screw hole into the new boat hook fitting.
5. Locate the drive screws furnished in the repair kit. They are a special type
of screw that is installed with a hammer. One or two solid taps is all that is
needed to seat them. Insert new drive screws into old screw holes and
hammer them home. Do not use excessive force.
Other
1 or 11/4"
poles
All other poles having a tube
outside diameter of
1" or 11/4" (25.4 or 32.0 mm)
and a wall thickness of .035" (.89 mm)
1. Use a tube cutter or hacksaw to cut off the
old or broken boat hook tip 11/2" (38 mm) from
end of tube. Be careful to make the cut as
square as possible. CAUTION: Extend
telescoping section before cutting.
1
1
/2"
(38 mm)
2. Deburr cut as necessary to insert
replacement boat hook tip.
3. If EEz-In
Insert new boat hook tip directly into cut end of tube.
If outside diameter 11/4" (32.0 mm):
Insert new boat hook tip into the adapter sleeve and then insert both
into cut end of tube.
®
or any brand with outside tube diameter 1" (25.4 mm):
4. Using a #24 or 5/32" (4 mm) drill bit,
drill through aluminum tube and boat
hook tip about 3/8" (10 mm) from end
of tube.
3/8"
(10 mm)
5. Locate the drive screws furnished in
the repair kit. This is a special type
of screw that is installed with a
hammer. One or two solid taps is all
that is needed to seat them.
Insert new drive screws into screw holes
and hammer them home. Do not use
excessive force.
Old
Hook
Cut
Here
New
Hook