Datavideo HS-2850-12 Instructions

Download

Page 1

HD/SD 12-CHANNEL PORTABLE VIDEO STUDIO

HS-2850

( 8 / 12 CHANNEL )

Instruction manual

Page 2

FCC COMPLIANCE STATEMENT ........................................................................................................................ 4

WARNINGS AND PRECAUTIONS ....................................................................................................................... 4

WARRANTY ...................................................................................................................................................... 5

STANDARD WARRANTY ............................................................................................................................................ 5

THREE YEAR WARRANTY ........................................................................................................................................... 5

DISPOSAL ......................................................................................................................................................... 6

CHAPTER 1 INTRODUCTION ...................................................................................................................... 7

1.1 FEATURES ................................................................................................................................................. 7

1.2 SYSTEM DIAGRAM ...................................................................................................................................... 9

CHAPTER 2 CONNECTIONS AND CONTROLS ............................................................................................ 10

2.1 MAIN UNIT – REAR PANEL OVERVIEW ......................................................................................................... 10

2.1.1 Rear Panel Connections .................................................................................................................. 10

2.2 CONTROL PANEL OVERVIEW ....................................................................................................................... 14

2.2.1 Video Switching ............................................................................................................................... 14

Program and Preset rows .......................................................................................................................................... 14

Background ............................................................................................................................................................... 15

2.2.2 Video Transitions ............................................................................................................................ 15

Transition Selection ................................................................................................................................................... 15

Triggering the Transition ........................................................................................................................................... 16

2.2.3 Logo and Clock ................................................................................................................................ 17

2.2.4 Picture-in-Picture and Downstream Key ......................................................................................... 17

2.2.5 Frame Store and Audio Control ....................................................................................................... 19

2.2.6 Crosspoint ........................................................................................................................................... 20

2.2.7 OSD MENU Options ......................................................................................................................... 20

2.2.8 PC Control – SE Remote Control Software ...................................................................................... 24

SET Function .............................................................................................................................................................. 25

REC & PLAY Functions ............................................................................................................................................... 26

Software-based Macro Functions.............................................................................................................................. 26

TIME Function ........................................................................................................................................................... 26

2.3 INTERCOM & MONITOR CONTROL PANEL ..................................................................................................... 27

2.3.1 Intercom Function ........................................................................................................................... 27

2.3.2 Monitor Function ............................................................................................................................ 28

2.3.3 Monitor Menu Options ................................................................................................................... 29

MAIN ADJUST ............................................................................................................................................................ 30

COLOR ....................................................................................................................................................................... 30

Information ............................................................................................................................................................... 31

Special Function ........................................................................................................................................................ 31

Factory Reset ............................................................................................................................................................. 31

CHAPTER 3 SWITCHER CONFIGURATION UTILITY (SECONFIG SOFTWARE)............................................... 32

3.1 NETWORK SETUP ..................................................................................................................................... 32

3.2 CONNECTING THE SECONFIG SOFTWARE TO THE SWITCHER ..................................................................................... 35

3.2.1 Change the Switcher IP Address ...................................................................................................... 37

3.3 SWITCHER TAB ......................................................................................................................................... 38

3.3.1 Profiles ............................................................................................................................................ 38

3.4 SETTINGS TAB .......................................................................................................................................... 38

3.4.1 Inputs tab ........................................................................................................................................ 39

3.4.2 Audio Tab ........................................................................................................................................ 40

Page 3

3.4.3 Video XPT Tab ................................................................................................................................. 43

3.4.4 Common Setup ................................................................................................................................ 45

3.4.5 Outputs Tab .................................................................................................................................... 48

3.5 IMAGES UPLOAD TAB ................................................................................................................................ 49

3.5.1 Still Pictures ..................................................................................................................................... 49

3.5.2 Logos ............................................................................................................................................... 50

3.5.3 Dynamic Logo ................................................................................................................................. 51

3.6 MULTI SCREEN WINDOW SIGNS (LABELS) TAB ................................................................................................. 52

3.7 MULTIVIEW LAYOUT TAB ........................................................................................................................... 53

3.8 MULTIVIEW UPLOAD TABS (A / B / C) ......................................................................................................... 54

CHAPTER 4 SWITCHER VIDEO .................................................................................................................. 55

4.1 HDMI MULTI-VIEW ................................................................................................................................. 55

4.2 VIDEO LAYERS ......................................................................................................................................... 56

CHAPTER 5 AUDIO FUNCTION ................................................................................................................. 58

5.1 OVERVIEW .............................................................................................................................................. 58

5.2 AUDIO MENU OPTIONS – DE-EMBEDDING SDI OR HDMI AUDIO ...................................................................... 58

5.3 AUDIO MENU OPTIONS – MONITORING THE AUDIO LEVELS .............................................................................. 60

5.4 AUDIO MENU OPTIONS – CHANGING THE AUDIO INPUT LEVEL .......................................................................... 61

5.5 WORKING WITH A FIXED OR SINGLE AUDIO SOURCE ......................................................................................... 61

5.6 SWITCHING BETWEEN DIFFERENT EMBEDDED AUDIO SOURCES ........................................................................... 61

5.7 AUDIO DELAY .......................................................................................................................................... 62

CHAPTER 6 APPLICATIONS ...................................................................................................................... 63

6.1 PICTURE-IN-PICTURE FUNCTION ................................................................................................................. 63

6.2 DOWN STREAM KEYER .............................................................................................................................. 64

6.3 HS-2850 AND CG SETUP .......................................................................................................................... 65

CHAPTER 7 APPENDICES.......................................................................................................................... 68

APPENDIX 1 UPGRADING HS-2850 TO 12 CHANNELS ............................................................................................. 68

APPENDIX 2 TALLY OUTPUTS .............................................................................................................................. 70

APPENDIX 3 GPI / GPO CONNECTIONS ................................................................................................................ 71

APPENDIX 4 FIRMWARE UPDATE ......................................................................................................................... 72

Keyboard Firmware Update ......................................................................................................................... 72

T-Bar Re-Calibration ..................................................................................................................................... 75

Monitor Firmware Update ........................................................................................................................... 76

APPENDIX 5 FREQUENTLY-ASKED QUESTIONS ........................................................................................................ 77

APPENDIX 6 DIMENSIONS & WEIGHT ................................................................................................................... 78

APPENDIX 7 SPECIFICATIONS............................................................................................................................... 79

SERVICE AND SUPPORT .................................................................................................................................. 81

Disclaimer of Product & Services

The information offered in this instruction manual is intended as a guide only. At all times, Datavideo Technologies will try to give correct, complete and suitable information. However, Datavideo Technologies cannot exclude that some information in this manual, from time to time, may not be correct or may be incomplete. This manual may contain typing errors, omissions or incorrect information. Datavideo Technologies always recommend that you double check the information in this document for accuracy before making any purchase decision or using the product. Datavideo Technologies is not responsible for any omissions or errors, or for any subsequent loss or damage caused by using the information contained within this manual. Further advice on the content of this manual or on the product can be obtained by contacting your local Datavideo Office or dealer.

Page 4

FCC Compliance Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause

undesired operation.

Warnings and Precautions

1. Read all of these warnings and save them for later reference.

2. Follow all warnings and instructions marked on this unit.

3. Unplug this unit from the wall outlet before cleaning. Do not use liquid or aerosol cleaners.

Use a damp cloth for cleaning.

4. Do not use this unit in or near water.

5. Do not place this unit on an unstable cart, stand, or table. The unit may fall, causing serious

damage.

6. Slots and openings on the cabinet top, back, and bottom are provided for ventilation. To

ensure safe and reliable operation of this unit, and to protect it from overheating, do not block or cover these openings. Do not place this unit on a bed, sofa, rug, or similar surface, as the ventilation openings on the bottom of the cabinet will be blocked. This unit should never be placed near or over a heat register or radiator. This unit should not be placed in a built-in installation unless proper ventilation is provided.

7. This product should only be operated from the type of power source indicated on the

marking label of the AC adapter. If you are not sure of the type of power available, consult your Datavideo dealer or your local power company.

8. Do not allow anything to rest on the power cord. Do not locate this unit where the power

cord will be walked on, rolled over, or otherwise stressed.

9. If an extension cord must be used with this unit, make sure that the total of the ampere

ratings on the products plugged into the extension cord do not exceed the extension cord rating.

10. Make sure that the total amperes of all the units that are plugged into a single wall outlet

do not exceed 15 amperes.

11. Never push objects of any kind into this unit through the cabinet ventilation slots, as they

may touch dangerous voltage points or short out parts that could result in risk of fire or electric shock. Never spill liquid of any kind onto or into this unit.

12. Except as specifically explained elsewhere in this manual, do not attempt to service this

product yourself. Opening or removing covers that are marked “Do Not Remove” may expose you to dangerous voltage points or other risks, and will void your warranty. Refer all service issues to qualified service personnel.

13. Unplug this product from the wall outlet and refer to qualified service personnel under

the following conditions:

a. When the power cord is damaged or frayed; b. When liquid has spilled into the unit; c. When the product has been exposed to rain or water; d. When the product does not operate normally under normal operating conditions.

Adjust only those controls that are covered by the operating instructions in this manual; improper adjustment of other controls may result in damage to the unit and

Page 5

may often require extensive work by a qualified technician to restore the unit to normal operation;

e. When the product has been dropped or the cabinet has been damaged; f. When the product exhibits a distinct change in performance, indicating a need for

service.

Warranty

Standard Warranty

• Datavideo equipment are guaranteed against any manufacturing defects for one year

from the date of purchase.

• The original purchase invoice or other documentary evidence should be supplied at the

time of any request for repair under warranty.

• Damage caused by accident, misuse, unauthorized repairs, sand, grit or water is not

covered under warranty.

• Viruses and malware infections on the computer systems are not covered under warranty.

• Any errors that are caused by unauthorized third-party software installations, which are

not required by our computer systems, are not covered under warranty.

• All mail or transportation costs including insurance are at the expense of the owner.

• All other claims of any nature are not covered.

• Cables and batteries are not covered under warranty.

• Warranty only valid in the country or region of purchase.

• Your statutory rights are not affected.

Three Year Warranty

• All Datavideo products purchased after July 1st, 2017 are qualified for

a free two years extension to the standard warranty, providing the product is registered with Datavideo within 30 days of purchase.

• Certain parts with limited lifetime expectancy such as LCD panels, DVD drives, Hard Drive,

Solid State Drive, SD Card, USB Thumb Drive, Lighting, Camera module, PCIe Card are covered for the first 10000 hours, or 1 year (whichever comes first).

Any three-year warranty claims must be made to your local Datavideo office or one of its authorized Distributors before the extended warranty expires.

Page 6

Disposal

For EU Customers only - WEEE Marking

This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and

electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

CE Marking is the symbol as shown on the left of this page. The letters "CE" are the abbreviation of French phrase "Conformité Européene" which literally means "European Conformity". The term initially used was "EC Mark" and it was officially replaced by "CE Marking" in the Directive

93/68/EEC in 1993. "CE Marking" is now used in all EU official documents.

Page 7

Chapter 1 Introduction

The HS-2850 is an 8 channel 10-bit 1920 x 1080i & cost-effective, broadcast-quality mobile hand carry switcher. Featuring 8 digital, it is designed for live events and TV programs that need to blend a variety of video and audio sources. HS-2850 is light weight, portable and powerful features for mobile switcher solution.

As a complete AV package, the HS-2850 HD mobile studio enables users to switch seamlessly between video and audio sources and blend high-quality digital content on the fly.

Advanced features include a 17.3-inch multi-image video monitor which displays multiple sources, as well as preview and program.

The system is equipped with an eight way intercom system and is supplied with four belt packs for effective communication between the whole production crew.

The HS-2850 is ideal for TV and video professionals working in outside broadcast or temporary video studios, such as theatres or conference centres. The HS-2850 is also a great value solution for the worship, education and AV market.

That’s Datavideo, sharing the value!

1.1 Features

Supports 8 or 12 HD or SD Inputs in a variety of configurations:

• HD Mode

- 8 / 12 HD-SDI

- 6 / 9 HD-SDI + 2 / 3 HDMI

• SD Mode

- 8 / 12 SD-SDI

- 6 / 9 SDI + 2 / 3 HDMI

- 4 SDI

- 4 SDI + 2 HDMI

• 3 SDI Outputs assignable to:

- AUX

- Program (PGM)

- Preview (PVW)

- PGM clean

• 1 HDMI outputs for multi view monitoring

• Audio I/O

- Input: 4 analogue balanced XLR

- Output: 2 analogue balanced XLR.

- Supports embedded audio SDI output from 4-CH XLR Audio input

Page 8

• Dual PIP displays with user-defined borders and positions

• Two DSK with a setup choice of basic Luma Key or Alpha Channel

• Built-in title overlay system (TC-200) that works with CG systems

• Cut, Mix and Wipe with borders

• Logo and Clock on screen

• Cross Point Assignment (XPT)

• Audio delay for each de-embedded audio source

• OSD SMPTE/ EBU Audio options

• Black burst PAL or Tri-Level Sync Reference

• Countdown counter on multi screen

• Tally, GPI interface and RJ45 for firmware upgrade

• Built-in 8 Channel Intercom System

• DC 12V operation voltage, available for mobile use

• One 17.3-inch monitor with a resolution of 1600x900 dots

Page 9

1.2 System Diagram

Page 10

Chapter 2 Connections and Controls

Input 1 – SD / HD-SDI

14.

User Defined SDI Outputs 1~3

Input 2 – SD / HD-SDI

15.

Sync Output / Ref Loop

Input 3 – SD / HD-SDI

16.

User Defined Multi view Output

Input 4 – SD / HD-SDI / HDMI

17.

Ethernet port for PC control & updates

Input 5 – SD / HD-SDI

18.

Tally Output connector

Input 6 – SD / HD-SDI

19.

GPI connector

Input 7 – SD / HD-SDI

20.

RS-422 connector (not currently used)

Input 8 – SD / HD-SDI / HDMI

21.

4pin XLR Power Input connector

Input 9 – SD / HD-SDI**

22.

Power Switch

10.

Input10 – SD / HD-SDI**

23.

3pin XLR Audio Inputs

11.

Input11 – SD / HD-SDI**

24.

3pin XLR Audio Outputs

12.

Input12 – SD / HD-SDI / HDMI**

25.

Monitor HDMI IN (External Video Input)

13.

External Sync Input

26.

To Beltpack

Video Input Modules (1 – 12)

Video Input Module. Each Video Input Module (shown left) has the same connections, four BNC connectors and one HDMI port. The fourth BNC connector and the

21 22

2.1 Main Unit – Rear Panel Overview

** Please note inputs 9 to 12 are not present if you have purchased the eight channel HS-

2850. Eight channel units can be upgraded to twelve inputs, please speak with your local dealer.

2.1.1 Rear Panel Connections

The HS-2850 can be supplied with eight or twelve video input channels.

An HS-2850 with eight input channels (Input 1 to 8) has two video input modules installed.

There are four video input channels on each

Page 11

HDMI port are an option for the same input

channel.

An HS-2850 with twelve input channels has

channel unit can be upgraded to twelve

SD Inputs

SDI

HDMI

1, 5 & 9

Yes

---

2, 6 & 10

Yes

---

3, 7 & 11

Yes

---

4, 8 & 12

Yes

1920x1080i

HD Inputs

HD-SDI

BNC

2850 switcher. For example, only input

SYNC I/O (13 / 15)

pass the sync signal to other studio

HDMI MULTIVIEW OUT (16)

which can be used to display a preset combination of inputs plus program and

five preset multi-view options.

three video input modules installed. An eight

inputs by adding another Video Input Module (Input 9 to 12).

1, 5 & 9 Yes ---

2, 6 & 10 Yes ---

3, 7 & 11 Yes ---

4, 8 & 12 Yes Yes

BNC

HDMI

The two tables, on the left, show which types of video inputs can be connected to the HS-

channels 4, 8 and 12 have the HDMI input option.

NOTE: This switcher cannot accept 1080P or 1280x720P or 1440x1080i inputs and has no computer input scaling options.

The HS-2850 can be synchronized with other studio equipment such as cameras and House sync. Input BNC (13) will accept House sync or Tri-level sync. Output BNC (15) can be used to

equipment such as cameras or recorders.

The HS-2850 has one HDMI outputs (16)

preset.

See the section on HDMI Multi-View for the

Page 12

SDI VIDEO OUTPUTS (14)

The three BNC output connectors (14) are

be a Program output which has been

ETHERNET PORT (17) AUDIO OUT (24)

AUDIO IN (23)

TALLY OUT (18)

user defined SDI outputs. Each of these SDI outputs has the option to be:

1. Program output

2. Preview output

3. Program output without logo

4. Program output without logo and DSK

5. Aux output of a selected input channel

SDI outputs 2 and 3 also have the option to

downscaled from HD to SD resolution.

This RJ45 Ethernet port (17) is used to connect the HS-2850 to a PC for remote control, or to update the unit’s firmware, or to configure the switcher. See Chapter 3 for more details.

Supports two channels of the XLR Balanced Audio output.

See Chapter 5 Audio Function for more details.

Supports four channels of the XLR Balanced Audio Input. See Chapter 5 Audio Function for more details.

The HS-2850 Tally Output port provides bicolour tally information to a number of other Datavideo products, such as the ITC-100 eight channel talkback system or the Datavideo TLM range of monitors.

See Appendix 1 for more details.

Page 13

GPI (19)

The GPI socket can be used for simple

RS-422 REMOTE (20)

Section 2.2.8 SE

DC IN (21)

Power Switch (22)

TO BELTPACK (26)

external control.

See Appendix 2 for more details.

In addition to the Ethernet port for remote control, you can also connect your PC to this port for controlling the HS-2850 with the SE Remote software. See

Remote Control Software for details.

Please check with your local Datavideo office for advice on this connection.

Connect the supplied 12V 5A PSU to this 4pin XLR socket.

Pin 1 = GND ( - ) Pin 2 = NC Pin 3 = NC Pin 4 = VCC ( + )

Intercom Channel Input / Output XLR Sockets

Each of the 8 channels has an XLR connector that carries bi-directional signals between the ITC-150 and ITC-100SL. All connections are contained within one cable.

The power switch turns ON/OFF the unit.

Page 14

2.2 Control Panel Overview

Frame Store & AUX button

Speed Selection

Crosspoint buttons

AUTO TAKE

PC / Menu control

10.

FTB – Fade To Black

Transition selection

11.

CUT

Logos 1 & 2, Clock & Timer

12.

T-Bar – Manual Transitions

PIP selection PST & PGM

13.

Preset Row (PST)

DSK selection PST & PGM

14.

Program Row (PGM)

1 2 34 5 6 7 8 9

2.2.1 Video Switching

Program and Preset rows

The Program row of buttons is the active channel, this is the live output. The active channel will appear as the Program Output (PGM). You can switch or CUT from one video source to another directly on the Program row. You will see the multi view PGM output change as you press different keys along this top row of buttons.

Page 15

The Preset row is the cued channel, this channel will appear in the PST or Preview window. The Preset row selection decides which input will be transitioned next when using any of the transition controls.

Note: The keys on the Program and Preset rows will be inactive while the T-Bar is active or moving. Only when the T-Bar is fully up or fully down will the keys respond.

Background

The Background button assigns a background colour or SMPTE 75% bars for use on the Program and Preset row.

2.2.2 Video Transitions

The HS-2850 features six user defined wipe buttons, an A/B dissolve or MIX button, an INV or Invert wipes button and a FREEZE button.

All wipes can have an optional colour border applied. The wipe border width and colour are chosen within the menu system.

Transitions can be performed manually using the T-Bar or automatically by using the SPEED and AUTO TAKE buttons.

Transition Selection

1. Vertical Wipe Left to Right.

Horizontal Wipe Top to

Bottom.

Vertical Wipes from Centre to

Left and Right sides.

INV Invert the selected wipe so it

travels in the opposite direction.

MIX

Pressing this button selects a basic A/B Dissolve for the next transition.

Horizontal Wipes from Centre to

Top and Bottom.

Circle Wipe from Centre to

outside edges.

Diamond Wipe from Centre to

outside edges.

FIX / A+V

Switch the audio mixing option between Audio Fixed and Audio-F-

Video (A+V).

FREEZE Freeze the program source image or

return to live video of the selected program source.

Page 16

Transition Effect Indication

The selected transition will be indicated

their opposite direction icon.

SPEED

AUTO TAKE CUT

FTB

T-Bar

options for more details.

in the status area of the HDMI multiview output. When the INV button is pressed, the six wipe icons change to

Triggering the Transition

There are three speed buttons which can be defined by the user. By pressing a speed button the user is choosing the rate of transition or time taken when using the AUTO TAKE button.

This performs an automated switch from the current program source to the selected preset source. The selected transition wipe or dissolve will also be used. The timing of the transition is set by the chosen Speed button.

This performs a simple immediate switch from the current main source to the selected sub source. The selected transition wipe or dissolve is not used.

Fade To Black, this button fades the current video program source to black. When pressed again it acts in reverse from complete black to the currently selected program video source.

This performs a manually controlled transition from the current program source to the selected preset source. The selected transition wipe or dissolve will be used. When the T-Bar has travelled as far as it can go, the transition between sources is complete. The T-Bar has indicators next to it, which light when the transition is complete.

The T-Bar can be operated in one of two modes which is chosen by a menu option, see the section on OSD MENU

Page 17

2.2.3 Logo and Clock

The HS-2850 has the ability to store six static logos and one dynamic logo. The logo files are transferred to the HS-2850 from a Windows PC using the Ethernet connection and the supplied SEConfig software. See Chapter 3 for more details on using this software.

LOGO 1 The LOGO 1 and LOGO 2 buttons are used to display pre-selected

logos on the HS-2850 Preset and Program outputs. When the button is active the selected logo is shown. These logos are selected from the switcher’s memory and positioned using a menu option see the section on OSD MENU options for details.

LOGO 2 or CLOCK The user cannot display LOGO 2 and CLOCK at the same time. Instead use LOGO 1 and CLOCK

together or use LOGO 1 and LOGO 2 together.

The clock time can be synchronized with a computer or set manually using a menu option. The colour and font used in the clock digits can be changed using the supplied SEConfig software. See Chapter 3 for more details on using this software or see OSD MENU Options onwards for the Clock menu options.

TIMER In some mixing or switching applications it is useful to have a countdown timer. It could be

that the input is a pre-recorded video clip and you need to know when to be ready to switch away from it.

This countdown timer function is only seen in the status area of the HDMI multi-view output to the right of the normal Clock function. The timer can be selected for one input channel, several channels or all channels.

When the TIMER button is active and the user switches to a selected input channel, the countdown starts on the HDMI multi-view.

The value of the countdown, in minutes and seconds (MM:SS), is set by a menu option. Whilst the countdown is in progress, T-Bar operation is ignored.

When the countdown reaches zero, the user can then switch or transition to another input channel. If the countdown reaches zero the switcher will not automatically change to the selected Preset source.

2.2.4 Picture-in-Picture and Downstream Key

PIP Preset and PIP Program

Page 18

When looking at the top right corner of the HS-2850 Control Panel / Keyboard there are four PIP keys. These are labelled Program and Preset. The upper PIP1 and PIP2 keys relate to activating Picture In Picture images on the Program outputs. The lower PIP1 and PIP2 keys relate to activating Picture In Picture images on the Multiview or Preview outputs.

Assigning a video source input to a PIP Using the lower PIP1 or PIP2 buttons you can assign a selected

video input to the chosen PIP video layer.

1. First press and hold down the required PIP button on the lower row. The Preset row

of input sources will light.

2. While still holding down the PIP button, press to select the required input from the

Preset row.

3. The input will flash to confirm it is selected.

This selection will also be confirmed on the HDMI Multi-view, with a PiP1 or PiP2 label shown next to the selected input image.

The full PIP process is described in the section on Picture-In-Picture Function.

DSK Preset and DSK Program

When looking at the top right corner of the HS-2850 Control Panel / Keyboard there are four DSK keys. These are labelled Program and Preset. The upper DSK1 and DSK2 keys relate to activating Down Stream Keying on the Program outputs. The lower DSK1 and DSK2 keys relate to activating Down Stream Keying on the Multi-view or Preview outputs.

Assigning an input to a DSK channel for keying

Using the lower DSK1 or DSK2 buttons you can assign a selected video input to the chosen DSK video layer.

1. First press and hold down the required DSK button on the lower row. The Preset row

of input sources will light.

2. While still holding down the DSK button, press to select the required input from the

Preset row.

3. The input will flash to confirm it is selected.

This selection will also be confirmed on the HDMI Multi-view, with a T1 or T2 label shown next to the selected input image.

The full DSK process is described in the section on DSK Settings.

Page 19

2.2.5 Frame Store and Audio Control

FS – Frame Store Button

The HS-2850 has eight or twelve video channels, depending on the number of inputs it has. Each of these channels has its own Frame Store, making a total of eight or twelve Frame Stores. Each of these Frame Stores can hold

one still image. This still image can be called into the production by using the FS button located at the top left corner of the HS-2850 Control Panel / Keyboard. The FS button allows the user to toggle between the still image of the Frame Store or the live video input also connected to that same video channel.

How to choose live video input or Frame Store

1. First press and hold down the FS button. The Preset row of input sources will light.

2. While still holding down the FS button, press the required input on the Preset row.

3. The input button will flash to confirm the Frame Store is selected.

This selection will also be confirmed on the HDMI Multi-view, with the selected channel showing the live input or frame store image.

The content of each Frame Store is uploaded to the HS-2850 from a PC. The supplied SEConfig software is used to do this. The file upload process is described in Chapter 3.

AUX Source Selection The auxiliary output (AUX) allows you to fix the SDI output onto a

particular input source. The HS-2850 has four user defined SDI outputs, see Section 2.1.1 item 14. One or all of these outputs can be set up as an auxiliary (AUX) output via a menu option. See OSD MENU Options onwards for details.

The AUX output source can be quickly selected in the following way.

1. First press and hold down the AUX button. The Input 1 and 2 buttons of the Program

row will light up red.

2. While still holding down the AUX button, press either the Input 1 button or the Input

2 button on the Program row.

3. The pressed input button (1 or 2) on the Program row will now flash red along with

one of the input buttons on the Preset row flashing green. The rest of the input buttons on the Preset row will remain solid green.

4. The green flashing button on the Preset row indicates the selected source of the AUX

output. To change the source, simply press other input buttons.

When you see the selected input button flashing green, your AUX output source is now assigned and you may release the AUX button to complete the AUX source selection.

Page 20

2.2.6 Crosspoint

Version Number

Base Standard

XPT Video

Assigning video source, and channel setting according to your preference.

The XPT Video source can be quickly selected in the following way.

1. First press and hold down the XPT VIDEO button. The Program row of input sources

will light.

2. While still holding down the XPT VIDEO button, press the required input on the

Program row.

3. After pressing the required input on the program row, the Preset row of input

sources will light. While still holding down the XPT VIDEO button, press the required input on the Preset row.

4. The input button will flash to confirm the video source is selected.

XPT Audio

Assigning audio source, and channel setting according to your preference.

The XPT Audio source can be quickly selected in the following way.

1. First press and hold down the XPT AUDIO button. The Program row of input sources

will light.

2. While still holding down the XPT AUDIO button, press the required input on the

Program row.

3. After pressing the required input on the program row, the Preset row of input sources

will light. While still holding down the XPT AUDIO button, press the required input on the Preset row.

4. The input button will flash to confirm the audio source is selected.

2.2.7 OSD MENU Options

When the ENTER button is pressed the Main Menu list is displayed on the HDMI 1 Multi-view output.

This section covers the Menu options in the order that they appear on the HS-2850 HDMI 1 Multi-view. These settings may also appear in more detail elsewhere in this instruction manual. Options may vary depending on the firmware version in use.

Once the chosen setting has been confirmed with the ENTER

button it is stored within the switchers non-volatile memory.

Version Number xx.xx where xx.xx is the firmware version number.

1080i50Hz

1080i60Hz

Tick selection for ON or OFF

Page 21

1080i59.94Hz

Audio Dynamic Range

Audio Tract

EXTERNAL ANALOG AUDIO

AUDIO PASS THROUGH

On Preview Video Adjustment

Brightness

72 to 184, default 128

Select the input that you

reduced.

Contrast

36 to 92, default 64

Saturation

36 to 92, default 64

Aperture

0 to 3

Y-C Delay

0 to 7

Video Input Standard and Format

Inputs 1,2,3,5,6,7,9,

Can be a choice of:

SD SDI 16:9

Inputs 4,8 &12

Can be a choice of

*All HD inputs are natively 16:9 aspect ratio.

On Preview Audio Level and Delay

Level

Range +60 to -60

AUDIO DELAY

Range 0 to 16

Nominal

Resets value to 00

SDI De-Emb. Audio Group / Pair

Input 1 – 12

User choice of

PAIR: 1-2

Audio Dynamic Range

Tick selection for ON or OFF

Set to Norminal Reset to default values

want to adjust in the PVW window.

This is a fine adjustment, the change happens gradually as the value is increased or

10&11

HD SDI 1080i * HD SDI 1080p (50/59/60Hz) * HD SDI 1080p (25/29/30Hz) * HD SDI 720p (50/59/60Hz) *

SD SDI 4:3

HD SDI 1080i * HD SDI 1080p (50/59/60Hz) * HD SDI 1080p (25/29/30Hz) * HD SDI 720p (50/59/60Hz) *

SD SDI 4:3 SD SDI 16:9

HD HDMI 1080i HD HDMI 1080p (50/59/60Hz) HD HDMI 1080p (25/29/30Hz) HD HDMI 720p(50/59/60Hz)

SD HDMI 4:3 SD HDMI 16:9 HDMI COLOR MODE: RGB / YUV 4:2:2 / YUV 4:4:4 / CG-200 MODE

GROUP: 1-4

Page 22

HDMI De-Emb. Audio Group

Input 4 / 8 / 12

User choice of GROUP 1 / 2 / 3 / 4

Outputs SDI Re-Emb. Group

Output 1 / 2 / 3 /4

User choice of GROUP 1 / 2 / 3 / 4

Auto Audio Mixing Type

X-Type

Tick selection / X type = A/B cross fade

V-Type

Tick selection / V type = Fade out A then Fade in B

T-Bar Audio Mixing Type

Follow Auto (X or V) Type

Tick selection / use the option enabled in Auto Audio Mixing Type

By the End

Tick selection / clean cut or immediate audio switch

PIP Set Up

Position PIP 1

Horizontal Position (Left to Right)

000-097

Vertical Position (Lower to Upper)

000-108 Size PIP 1

1 (Small) – 33 (Large)

Border PIP 1

Width

00-05

Color

1-8

1=White, 2=Yellow,

8=Black

Position PIP 2

Horizontal Position (Left to Right)

000-097

Vertical Position (Lower to Upper)

000-108 Size PIP 2

1 (Small) – 33 (Large)

Border PIP 2

Width

00-05

Color

1-8

8=Black

Logo Set Up

Logo 1

Select

01-08

moving image

Horizontal Position (Left to Right)

000-110

Vertical Position (Lower to Upper)

000-135

Logo 2

Select

01-08

still image

3=Cyan, 4=Green, 5=Magenta, 6=Red, 7=Blue,

1=White, 2=Yellow, 3=Cyan, 4=Green, 5=Magenta, 6=Red, 7=Blue,

Logo selection 1 to 7 are still image Logo 8 selection is dynamic

Logo selection 1 to 7 are

Page 23

Logo 8 selection is dynamic moving image

Horizontal Position (Left to Right)

000-110

Vertical Position (Lower to Upper)

000-135

Speed Button Set Up

Speed 1

1-64 (Frames)

Speed 2

1-64 (Frames)

Speed 3

1-64 (Frames)

Wipe Button Set Up

Button 1-6

WIPE

1-8

Soft Edge

0-4

Color

1-8

1=White, 2=Yellow,

8=Black

Outputs Mode and Standard

Output 1/2/3/4

Standard & Format

HD SDI

SD SDI 4:3

SD SDI 16:9

Mode

Program

Program logo free

Program logo & DSK free

Preview

AUX 1

AUX 2

DSK Set Up

DSK 1 / 2

Fill & Key mode

Alpha channel

Luma Key mode

Luma Key level

0 (black) to 255 (white)

BG Color (1-8) and Color Bar (9)

1-9

Background Color Settings

7=Blue, 8=Black, 9 = SMPTE 75% colour bars

T-Bar Mode

One Way Mode

= T-Bar operates transition in only one direction

Two Way Mode

= T-Bar operates transition in both directions

1kHz to Color Bar

Tick selection for ON or OFF

Keys Brightness

1-4

Keyboard button brightness with user choice of 1 to 4 1 = Low, 4 = High

Multi-Screen Audio Indicators

Tick selection for ON or OFF

Reference

3=Cyan, 4=Green, 5=Magenta, 6=Red, 7=Blue,

1=White, 2=Yellow, 3=Cyan, 4=Green, 5=Magenta, 6=Red,

Page 24

External

Reference

Tick selection for ON or OFF

Mode HD: Analog 3 Level Signal

Tick selection for ON or OFF

SD: Composite Signal

Tick selection for ON or OFF

H-Timing

0-255

Factory Settings

Tick selection for ON or OFF

Resets to factory default

Clock Settings

Horizontal Position (Left to Right)

000-110

Vertical Position (Lower to Upper)

000-124 SET Hours

0-23

SET Minutes

0-59

Clear Seconds

Tick selection for clearing second

Multi Screen Mode

This option relates to the HDMI outputs 1 and 2.

A: M1=PVW+PGM+3 IN; M2=9 IN

B: M1=PVW+PGM+12 IN; M2=PGM

C: M1=PVW+PGM+8 IN; M2=PGM

D: M1=PVW+PGM+12 IN; M2=M1

E: M1=PVW+PGM+8 IN; M2=M1

GPI Settings

Input Select

00-12

Chosen input number

Time Delay

In frames between 1 to 75

Mode Level Mode

Tick selection for ON or OFF

Pulse Mode

Tick selection for ON or OFF

Countdown Timer Settings

Input 1-12

Count Down Enable

Each input can be selected for Count Down ON or OFF.

Down Counter Value

If Count Down is ON then

or 00:15

Multi-Screen Audio Source

Preview

Tick selection of Program or Preview audio on the HDMI outputs

Program

Control Interface

Ethernet

Tick selection for ON or OFF RS422

2.2.8 PC Control – SE Remote Control Software

the Down Counter value is set in minutes and seconds (MM:SS) - Max.= 1 Hour or 60:00, Default = 15 Seconds

It is possible to control the HS-2850 with a Windows 7 computer using an Ethernet connection. The SE Remote software supplied with the switcher needs to be installed on the computer first. The HS-2850 then needs to be placed into PC Control mode. To do this press the PC

Page 25

Control button on the HS-2850 Control Panel. Once launched, the Remote software displays an image of the HS-2850’s keyboard as shown below. Any active functions or selections will be shown with a red button or key. These buttons or keys can be clicked with a mouse or alternatively you could use a touch screen monitor.

Before launching the SE Remote software, please see Chapter 3 Switcher Configuration

Utility for network setup information.

NOTE: It is not possible to run both the SEConfig and SE Remote software applications at the

same time.

SET Function

After the network connection between the PC and the HS-2850 is successfully configured, you can then launch the SE Remote software on the PC. Locate SET function button which is located just above the T-Bar. When clicked, a new window will open as shown left below. This Settings window is used to match the software to the IP address of the connected HS-2850 switcher.

Enter the switcher’s IP address and then click the “Check” button to determine the switcher model number which is then selected from the “Model” pull-down menu. Once configured,

Page 26

click the OK button to shut down to “Settings” window and the SE Remote software should be successfully connected to the HS-2850 as shown in the diagram below.

REC & PLAY Functions

Left mouse click the grey REC button and it will light up red. All of your actions when using the Remote Console will now be recorded to file. The only action that will not be recorded is the T-Bar, use the CUT or AUTO TAKE buttons instead. The function buttons just above the TBar as listed on this page are also ignored.

Click the red REC button again and a save window will appear. You can now save the recorded actions as a macro text file to a chosen location on the computer.

Click the grey PLAY button and a load file window will appear. You can now browse to and load a macro text file. When you load a file the recorded actions will begin to play back until the end of the file.

Software-based Macro Functions

It is possible to record a Macro type playlist to the computer when using the SE Remote software. This Macro function allows these pre-recorded keyboard actions or selections to be played back within a project where timing is important or where the same steps are repeated throughout the production. The Macro function buttons are REC, and PLAY. These buttons are located just above the T-Bar in the SE Remote display above.

TIME Function

This button is located just above the T-Bar in the SE Remote display above. Mouse clicking on the TIME button will synchronize the time on the HS-2850 switcher to the current time on the computer.

Page 27

Intercom Function

Monitor Function

ts Dynamic Gooseneck

Opens communication with individual channels.

2.3 Intercom & Monitor Control Panel

2.3.1 Intercom Function

USB Port

USB port for LED power supply and Firmware Upgrade.

XLR Microphone Socket

Combined XLR XLR / ¼” (6.3mm) Jack Microphone Input for either a Condenser or Dynamic Gooseneck Microphone.

• XLR supports Condenser Microphones

• ¼” (6.3mm) Jack suppor

Microphone

ALL Button

Opens communication with all channels. All channels will hear communication from the operator, or from any other channel using the TALK button.

Channel Buttons 1~8

More than 1 channel can be active at any given time, active channels are illuminated red.

All active channels will hear any communication from the operator or from any other active channel.

The buttons will also indicate if any channel is paging, the paging channel will flash in orange until the page is answered.

Page 28

HDMI, Multiview, PROGRAM

BLUE PATTERN

ZOOM

Menu Navigation Buttons

2.3.2 Monitor Function

MUTE Button

Mutes all communication from the base station or any channel.

Select the type of input you are using - HDMI, Multiview, PROGRAM.

The active input will be indicated by a red LED on the Source Button. When you push the “HDMI” button, you select the 17.3" display from the HDMI source input of Rear Panel; it is a full screen display. When you push the “MV” button, then you go back to show multi-view so you can switch back & forth between HDMI & Multiview.

Press this button to eliminate the red and green component of input signals. Only the blue component of an input is displayed on the screen.

Press the PATTERN Key to activate the colour bar.

The ZOOM Feature Setting Menu allows you to adjust the screen display size.

Display and navigate the set up menus - See Menu Options for more details

UP Button also switches the 4:3 Mask On / Off - (only available in 16:9 modes)

Page 29

Aspect Ratio Button

Sets the Aspect Ratio to 16:9 / 4:3

Mute Button Volume Control & Audio Meter

PWR

Main Options

Sub Options

Parameters

MAIN ADJUST

BRIGHTNESS

0~100

CONTRAST

0~100

SHARPNESS

0~100

SATURATION

0~100

TINT

0~100

BACK LIGHT

0~100

HIGH / MID / LOW / OFF

MPEG NR

HIGH / LOW / OFF

VOLUME

0~100

EXIT

COLOR Adjust

7500

9300

6500

USER COLOR

RED

0~100

GREEN

0~100

Mutes the audio from the internal speakers or headphone socket.

Adjusts the speaker / headphone volume up / down.

Switches the TLM-170 Power ON / OFF.

2.3.3 Monitor Menu Options

The HS-2850 Monitor is set up via on screen menus. To display the on screen menu, press the MENU button.

The menus are navigated using the Up / Down buttons.

Press Enter button to enter or exit the menu mode.

Page 30

BLUE

0~100

EXIT

SCAN SETTING

UNDER SCAN

OVER SCAN

INFORMATION

H. FREQUENCY

V. FREQUENCY

RESOLUTION

VER.

LANGUAGE

English [default]

Francis

Deutsch

Español

Italiano

Dutch

Português

Russian

EXIT

SPECIAL

FUNCTION

OSD TIMEOUT

5-120 SEC

FRAME RATIO

90 / 80 / 0FF

4:3 MARK LINE

ON / OFF

CENTRAL MARK

ON / OFF

CINEMA ZONE MARK

ON / OFF

AUDIO CHANNEL L*

1/2/3/4

AUDIO CHANNEL R*

1/2/3/4

EXIT

FACTORY RESET

EXIT

To access the menu press enter so that Color Adjust option is highlighted

To access the option for the selected color setting, press enter again.

Use the Up / Down buttons to navigate the available color settings.

* Selectable on PGM only; external HDMI and MV are allowed on 1 and 2 ONLY

MAIN ADJUST

The first menu to be displayed is the MAIN ADJUST Menu.

To access the MAIN ADJUST Menu press enter, the Brightness setting will be highlighted.

To adjust the Brightness press Enter again. Use the Up / Down buttons to change the setting and then press Enter to store the new value and return to the main menu.

To select a different setting (Brightness, Contrast, Saturation, Sharpness, TINT), use the Up / Down buttons. Follow the same procedure to set other values.

COLOR

Page 31

You can choose:

7500

9300

6500

USER COLOR

Information

Once selected, the information will be displayed as follows:

You will see:

H. FREQUENCY

33.7KHZ

V. FREQUENCY

60.0HZ

RESOLUTION

1920X1080I

VER.

0.11

To access the options for the selected setting press enter again, so that the option is highlighted

Use the Up / Down buttons to navigate the available options.

You can choose:

OSD TIMEOUT

5-120 SEC

FRAME RATIO

90 / 80 / 0FF

4:3 MARK LINE

ON / OFF

CENTRAL MARK

ON / OFF

CINEMA ZONE MARK

ON / OFF

AUDIO CHANNEL L*

1/2/3/4

AUDIO CHANNEL R*

1/2/3/4

The System Information Menu displays Horizontal Frequency, Vertical Frequency, Resolution and the Firmware Version of the monitor.

Special Function

The Special Function Menu has settings for the OSD TIMEOUT, Frame Ratio, 4:3 MARK LINE, Central Mark, Cinema Zone Mark and Audio Channel L & R.

Factory Reset

The monitor menu offers a Factory Reset option, which will return all the settings of the monitor to the factory defaults

Page 32

To reset the monitor press the MENU button and then use the UP / Down button to navigate to FACTORY RESET option. Press ENTER again to reset the monitor. After a few seconds the monitor will be reset.

Chapter 3 Switcher Configuration Utility (SEConfig Software)

The Switcher Configuration Utility or the SEConfig Software allows you to configure the HS- 2850 with a Windows 7 computer using an Ethernet connection. Before launching the Switcher Configuration Utility, make sure it is installed on your computer.

3.1 Network Setup

Before you attempt to establish connection between PC and your HS-2850, you have to manually configure the PC network settings first. Follow the steps outlined below to assign a static IP address to your PC.

(1) Connect the PC to the HS-2850 switcher using an Ethernet cable. (2) Turn on the PC and the HS-2850. (3) The HS-2850 then needs to be placed into PC Control mode. To do this press the PC

Control button on the HS-2850 Control Panel or keyboard.

(4) Find the switcher’s IP address using the SEConfig software. Double click the SEConfig

software icon to open the Switcher Configuration Utility program.

(5) The Find button within the SEConfig software will help confirm the IP address of the

switcher. See later sections in this Chapter for more information on SEConfig. In the example below, the IP address of the switcher is 192.168.0.101.

Page 33

(6)

Once you have obtained the switcher’s IP address, go to Control Panel, open Network and Sharing Center and then click Ethernet.

(7) On the Ethernet Status Window, click the Properties button.

Page 34

(8) On the Ethernet Properties window, double click Internet Protocol Version 4 (TCP/IPv4)

to open a window on which you will be allowed to manually enter an IP address for your PC.

Page 35

(9)

Please remember that the PC used must be in the same IP network as the HS-2850. So the first three octets (numbers) in the IP Address field must match the first three octets of the switcher IP address. The fourth octet should be a different number for the PC and switcher. In the example below, we have entered an IP address of 192.168.0.100 with the Subnet Mask of 255.255.255.0.

Note: To reset the IP Address of the PC/laptop use the Network and Sharing Center option in Windows 7 Control Panel. Click on Local Area Connection then Properties. Click to highlight

Internet Protocol Version 4 (TCP/IPv4) then click Properties again. Then click Use the following IP address.

3.2 Connecting the SEConfig Software to the Switcher

1. Double click the SEConfig DV icon to launch the application.

Page 36

2. If you immediately get an error

window, do not worry, this just means

3. Make sure the “PC Control” button is

4. Select Ethernet to display the

Switcher’s IP Address in the

drop down list. The first three

5. Click Connect and additional function

tabs will immediately become

the “PC Control” button in the MENU area of the HS-2850 keyboard has not been enabled.

enabled and then click OK.

Computer’s IP Address. Click the Find button to find and display the HS2850

numbers in both IP addresses should match. See the example on the left.

available at the top of the application window. These are:

• Switcher

• Settings

• Images Upload

• M/V Input Source Labels

• M/V Layout

• M/V ‘A’ Upload

• M/V ‘B’ Upload

• M/V ‘C’ Upload

Page 37

3.2.1 Change the Switcher IP Address

The Switcher Network Setup Utility allows the user to change the switcher IP address. Locate, on your desktop, the icon as shown in the diagram below and then double click it to open the utility software.

After the Switcher Network Setup Utility is opened, you will see the following SE Network Setup window on the screen.

To change the IP address, click the Setup button to display the Network Parameters as shown in the diagram below. Update the network parameters accordingly.

Use the network PING feature to check if the IP change is successful. You will get the PING reply from the switcher if the IP is valid and the connection has been successfully established.

Page 38

3.3 Switcher tab

This first tab can be used to choose the method of connection between the computer and the switcher. In this case the HS-2850 is connected using selected Ethernet IP addresses.

Note that the first three numbers in the IP addresses of the switcher and computer should be the same. The last number in each IP address should be unique.

If you are connecting for the first time you may be asked by the computer to change the firewall setting to allow this application to connect to the switcher.

3.3.1 Profiles

It is possible to store the current profile or settings of the switcher to your computer. This file can then be restored to the machine at a later date allowing simple configuration of the unit. Depending on the included levels of the profile this save process may take some time to complete.

3.4 Settings tab

The settings tab is another way to change the menu settings of the switcher. The options may appear in a slightly different order from those in the onscreen menu described in Section

2.2.7.

Page 39

Each menu option in the left hand pane can be expanded by clicking on the plus sign in the

Video Adjustment

decreased.

Brightness

-56 - +56

Contrast

-28 - +28

Saturation

-28 - +28

YC Delay

-4 - +3

Aperture

0 - 3

Audio Adjustment

decreased.

Audio Level

-60 - +60

Audio Delay

0 - 17

Option of Input

Type, Format, Aspect and

SDI SD 4:3

SDI 3G 1080p

left hand pane. The right hand pane shows any values which can be changed.

3.4.1 Inputs tab

The Input settings of inputs 1 to 12 can thus be configured from the computer. Clicking the Inputs tab will display a list of various input settings.

Note due to the design of the switcher, different inputs (SDI or HDMI) may have more or less options as they are not all the same. See Rear Panel Connections.

This is fine tune adjustment, the change occurs gradually as the value is increased or

All HD inputs are natively 16:9 aspect ratio.

Definition

SDI HD 1080i SDI SD 16:9 SDI HD 720p

Page 40

SDI HD 1080p

SDI De-Embedded Audio

Group and Pair

1/2/3/4 and Pair 1/2

Audio Group

Audio group 1 / 2 / 3 / 4

Stereo Pair

Stereo pair 1 / 2

Countdown

Seconds or 00:15.

Timer Enable

ON / OFF

Countdown Duration

1 – 3600

HDMI Color Mode

Modes

RGB

YUV 4:4:4

HDMI De-Embedded Audio

HDMI Audio Pair

Stereo Pair 1

Stereo Pair 4

User choice of Group

Each input can be selected for Countdown ON or OFF. If Countdown is ON then the Down Counter value is set in minutes and seconds (MM:SS) – MAX. = 1 Hour or 60:00, and Default = 15

Options in the table below will be available for HDMI inputs.

User choice of HDMI Color

Pair

User choice of Pair 1/2/3/4

YUV 4:2:2

Stereo Pair 2 Stereo Pair 3

3.4.2 Audio Tab

The Audio settings of inputs 1 to 12 can be configured from the computer. Clicking the Audio tab will display a list of various audio settings as shown in the diagram below.

Page 41

Audio Tract Mode

External Analog Audio

Audio Pass Through

Audio Dynamic Range

-18 dBFS / -24dBFS

T-Bar Audio Switching

As selected Audio Mixing Type

User choice of Audio Mixing

Limit Switch.

T-Bar reaches the Limit Switch

Audio Mixing Type

Type V

User choice of X type (A/B

out A then Fade in B)

Type X

Audio XPT

Audio source from Input 1 to:

Audio source from Input 1

Button 8

Audio source from Input 2 to:

Audio source from Input 2

Button 5

Mode

Any of input audio sources can be associated with any of input button (or buttons). Different video sources with the same audio.

Type (X or V) or Clean Cut after the T-Bar reaches the

cross fade), V type (Fade

to: Button 1 Button 2 Button 3 Button 4 Button 5 Button 6 Button 7

to: Button 1 Button 2 Button 3 Button 4

Page 42

Button 6

Button 7

Button 8

Audio source from Input 3 to:

Audio source from Input 3

Button 8

Audio source from Input 4 to:

Audio source from Input 4

Button 8

Audio source from Input 5 to:

Audio source from Input 5

Button 8

Audio source from Input 6 to:

Audio source from Input 6

Button 8

Audio source from Input 7 to:

Audio source from Input 7

Button 4

to: Button 1 Button 2 Button 3 Button 4 Button 5 Button 6 Button 7

to: Button 1 Button 2 Button 3

Page 43

Button 5

Button 6

Button 8

Audio source from Input 8 to:

Audio source from Input 8

Button 8

Video XPT

Video from Input 1 to:

Button 6

Button 7

to: Button 1 Button 2 Button 3 Button 4 Button 5 Button 6 Button 7

3.4.3 Video XPT Tab

The user can also set the Input Video Crosspoints from the computer. Clicking the Video XPT tab will display a list of configurable video inputs as shown in the diagram below.

Any of video sources can be associated with any of Console 1-8 buttons.

Button 1 Button 2 Button 3 Button 4 Button 5

Page 44

Button 7 Button 8

Video from Input 2 to:

Button 1

Button 8

Video from Input 3 to:

Button 8

Video from Input 4 to:

Button 8

Video from Input 5 to:

Button 8

Video from Input 6 to:

Button 8

Video from Input 7 to:

Video from Input 7 to: Button 1

Button 2 Button 3 Button 4 Button 5 Button 6 Button 7

Button 1 Button 2 Button 3 Button 4 Button 5 Button 6 Button 7

Page 45

Button 2

Button 3

Button 8

Video from Input 8 to:

Button 8

AUX Source

AUX 1 Source

1 – 12

AUX 2 Source

1 – 12

Button 4 Button 5 Button 6 Button 7

Button 1 Button 2 Button 3 Button 4 Button 5 Button 6 Button 7

Note: In the HS-2850, each input source must be associated with only one button. If you associate one source to more than one button, corrupted small windows will appear on the HS-2850 Multiview display. To avoid this please make sure your XPT setting is configured to one input to one button arrangement.

3.4.4 Common Setup

The Common Setup tab will allow you to set up various image effects such as the logo, DSK and PiP, as well as WIPE transition effects.

Page 46

Clock Position

X-Position = Left to

Clear Seconds

Clock X

0 – 110

Clock Y

124 – 0

Console

T-Bar Mode

One Way

T-Bar operates

one direction.

Two Way

T-Bar operates

directions.

Keys Brightness

1 – 4

BG Key Setup

Color 1

User choice of

Palette setup.

Color 2

Color 3

Color 4

Color 5

Color 6

Color 7

Color 8

BARS 1kHz Audio Test

1kHz to BARS is ON

When BG Color

ON or OFF.

1kHz to BARS is OFF

Speed Buttons

speed).

Run time of effects for Button 1

4-100

Run time of effects for Button 2

4-100

Run time of effects

4-100

DSK

DSK 1

DSK 1 Mode Luma Key mode

Fill and Key mode

Luma Key 1 Threshold Level

0 – 255

DSK 2

DSK 2 Mode Luma Key mode

Fill and Key mode

Luma Key 2 Threshold Level

0 – 255

Right; Y-Position = Lower to Upper; Set Hours; Set Minutes;

transition in only

transition in both

(Palette + BARS)

to BARS

Preset Run time of effects: Min. = 4 Frames (maximum speed); Max. = 64 Frames (minimum

background color from 1 to 9. By default, color is 1. 1 = White; 2 = Yellow; 3 = Cyan; 4 = Green; 5 = Magenta; 6 = Red; 7 = Blue; 8 = Black; 9 = SMPTE 75% Color Bars. The color can be changed in the

setting is 9 (BARS), 1kHz tone can be

for Button 3

HS-2850 has FILL and KEY model (alpha channel) and LUMA KEY mode 0 (black) to 255 (white).

Page 47

External Clocking

Reference Enable

Checkbox

Reference Mode CVBS PAL

3 Level Sync

H-timing

0 – 255

GPI

GPI Input

1 – 12

GPI Delay

0 – 75

GPI Mode Level Mode

Pulse Mode

Logos

X Position = Left to

image.

Logo 1

Logo 1 Picture

1 – 8

Logo 1 X

0 – 110

Logo 1 Y

124 – 5

Logo 2

Logo 2 Picture

1 – 8

Logo 2 X

0 – 110

Logo 2 Y

124 – 5

Palette

be changed by user.

Get Color 1

Get Color 2

Get Color 3

Get Color 4

Get Color 5

Get Color 6

Get Color 7

Get Color 8

PiP

PiP 1

PiP X-Axis Position

0 – 97

PiP Y-Axis Position

108 – 0

Picture Size

33 – 1

Border Width

0 – 5

Border Color

1 – 8

PiP 2

PiP X-Axis Position

0 – 97

PiP Y-Axis Position

108 – 0

Picture Size

33 – 1

Border Width

0 – 5

Border Color

1 – 8

PiP Border Color

Color 1 Density

0 – 15

Color 2 Density

0 – 15

Color 3 Density

0 – 15

Color 4 Density

0 – 15

Color 5 Density

0 – 15

Color 6 Density

0 – 15

Color 7 Density

0 – 15

Color 8 Density

0 – 15

WIPES

WIPES 1

Effect

1 – 8

Right; Y Position = Lower to Upper; Options 1 to 8. Logo options 1 to 7 are still images. Logo 8 is dynamic moving

Common palette for all colors used in Wipes / Border / Background / PiP Border. By default, 75% YCbCr Color Bar from White (Color 1) to Black (Color 8). Any Palette Color can

Logo options 1 to 7 are still images. Logo 8 is dynamic moving image.

User choice of position, window size, border width, and border color from 1 to

9. By default the color is 1. 1 = White; 2 = Yellow; 3 = Cyan; 4 = Green; 5 = Magenta; 6 = Red; 7 = Blue; 8 = Black; 9 = SMPTE 75% Color Bars. The color can be changed in the Palette setup.

Density

Page 48

User choice of Wipe 1

to 8; Soft Edge 0 to 4;

Border Width

1 – 5

Border Color

1 – 8

WIPES 2

Effect

1 – 8

Border Width

1 – 5

Border Color

1 – 8

WIPES 3

Effect

1 – 8

Border Width

1 – 5

Border Color

1 – 8

WIPES 4

Effect

1 – 8

Border Width

1 – 5

Border Color

1 – 8

WIPES 5

Effect

1 – 8

Border Width

1 – 5

Border Color

1 – 8

WIPES 6

Effect

1 – 8

Border Width

1 – 5

Border Color

1 – 8

Output 1

Source to Output Program

Program Logo Free

Border Colour from 1 to 8. By default, color is 1. 1 = White; 2 = Yellow; 3 = Cyan; 4 = Green; 5 = Magenta; 6 = Red; 7 = Blue; 8 = Black; 9 = SMPTE 75% Color Bars. The color can be changed in the Palette setup.

3.4.5 Outputs Tab

The Output settings of outputs 1 to 4 can also be configured from the computer. Clicking the Outputs tab will display a list of various input settings.

Page 49

Program Logo and Titles Free

Preview

AUX 1

AUX 2

Format: HD; SD; SD 16:9

SD 16:9

Re-Embedded Audio Group

1-4

Output 2

Source to Output

Program

Program Logo Free

Program Logo and Titles Free

Preview

AUX 1

AUX 2

Format: HD; SD; SD 16:9

SD 16:9

Re-Embedded Audio Group

1-4

Output 3

Source to Output

Program

Program Logo Free

Program Logo and Titles Free

Preview

AUX 1

AUX 2

Format: HD; SD; SD 16:9

SD 16:9

Re-Embedded Audio Group

1-4

Output 4

Source to Output

Program

Program Logo Free

Program Logo and Titles Free

Preview

AUX 1

AUX 2

Format: HD; SD; SD 16:9

SD 16:9

Re-Embedded Audio Group

1-4

3.5 Images Upload tab

3.5.1 Still Pictures

Each switcher has the ability to store still pictures in its frame stores. If the switcher has eight inputs it has the ability to store eight still pictures. Twelve pictures can be stored if the unit has twelve inputs. See FS button in Section 2.2.5 also.

Page 50

The LOAD button can be used to browse for a picture stored on the computer. This picture is then loaded into the application window. Loading options must be selected before loading.

The WRITE button can then be used to save the new picture into a selected frame store on the switcher.

3.5.2 Logos

The HS-2850 can store up to eight still logos in its memory.

Using the logos tab you can use the LOAD button to browse for a logo stored on the computer. This logo is then loaded into the application window.

The WRITE button can then be used to save the new logo into a selected logo store on the switcher.

Page 51

3.5.3 Dynamic Logo

The HS-2850 can store one dynamic moving logo in its memory. The dynamic logo can be a targa (TGA), png, bmp or jpg sequence, GIF or AVI. It must be no longer than 75 frames/images long.

Using the Dynamic logo tab you can use the LOAD button to browse for a logo sequence of images stored on the computer. This logo sequence is then loaded into the application window. The sequence is indicated by the number in the title (two digits: 01, 02 and etc). Click the EDIT button to import the source file to the built-in editor, which converts the file to the dlb format for saving on the device.

The WRITE button can then be used to save the new logo sequence into the dynamic logo store on the switcher.

Page 52

3.6 Multi screen window signs (labels) tab

This tab allows the user to rename the input source labels on the HDMI multi view.

Page 53

The READ button can be used to load the current label of a selected input into the application

W1 = PVW / PGM / Inputs 1-2 W2 = Inputs 3-8

W1 = PVW / PGM / Inputs 1-8 W2 = PGM

W1 = PVW / PGM / Inputs 1-8 W2 = W1

window on the left. This selected label can then be edited using the TEXT box. If required the font and colour of the text can also be changed.

The WRITE button can then be used to write the new label text into the switcher’s memory.

3.7 Multiview Layout Tab

The Multiview Layout Tab allows you to set the Multiview Layout displayed on the two HDMI outputs.

There are five variants listed as follows:

The “Audio level bars to Multi View” option allows you to enable / disable the audio level bars on the Multiview window.

Page 54

3.8 Multiview Upload Tabs (A / B / C)

These three tabs are used to write new Multiscreen layouts to the switcher in order to change the HDMI multi-view layouts as described in the HDMI Multi-View section.

The user can change Multiview layout. Simply clicking the “LOAD” button to browse for a Multiview files (file extension *.mss) stored on the computer. This file is then loaded into the application window. The WRITE button can be used to set the new Multiview layout.

NOTE: Only change these layouts with guidance from your local Datavideo office as attempting to edit or load your own layouts may result in a poor outcome or a non-responsive switcher.

Page 55

Chapter 4 Switcher Video

HDMI 1 HDMI 2

Shown left are the five multi-view

view option on your

button in the

4.1 HDMI Multi-View

HS-2850 Multi-view monitoring is available across one or two HDMI monitors (not supplied). These HDMI outputs can be used to monitor video and audio in a number of different configurations. For each setup, embedded audio level indication is also available on all inputs as well as the Preview and Program windows.

This Multi-view is supplied from the HDMI connection(s) on the rear panel. (See Rear Panel, item 16.) When connected to two compatible HDMI monitors, a variety of multi-image layouts is possible.

Configuration A:

- On HDMI screen 1: 9 live inputs

- On HDMI screen 2: 3 live inputs with additional Preview and Program windows

Configuration B:

- On HDMI screen 1: 12 live inputs with additional Preview and Program windows

- On HDMI screen 2: Program window

Configuration C:

- On HDMI screen 1: 8 live inputs with additional Preview and Program windows

- On HDMI screen 2: Program window

Configuration D:

- On HDMI screen 1: 12 live inputs with additional Preview and Program windows

- On HDMI screen 2: Same as HDMI screen 1

Configuration E:

- On HDMI screen 1: 8 live inputs with additional Preview and Program windows

- On HDMI screen 2: Same as HDMI screen 1

configuration options A to E.

How to change the Multi-view output

To change the multiswitcher press the ENTER MENU area of the HS-2850 Control Panel / Keyboard. This will display an on screen menu on HDMI output 1. Then use the arrow down button to highlight the option Multi Screen

Mode. Use the arrow keys to highlight your preferred option from those shown on the

left. Use the arrow keys to place a tick in the selection box and then press ENTER to save this choice.

Page 56

On screen Tally indication

The HS-2850 Multi-

Image Preview supplies

the cued next input source with a yellow

Below the Program and Preset image

time Clock, Countdown Timer (if active),

ut channel window

basic tally information by highlighting the live Program input source with a red border, and

border.

Function Area

windows is a function area occupied by a real

chosen Wipe indicator, PC or Console control indication and chosen Audio mix and Audio level indicators.

Labels

Below each video inp there is a label. These labels can be edited using the software supplied with the HS2850, see Chapter 3 for more details.

4.2 Video Layers

The HS-2850 is a Standard Definition or High Definition Digital Video Switcher and as well as mixing video and audio sources it has additional functions such as Picture In Picture (PIP), DSK LUMA KEY and LOGOs.

Before attempting to use the HS-2850’s PIP, DSK LUMA KEY and LOGO functions it may help to first understand the order of the video layers at the HS-2850 Program (PGM) outputs.

Page 57

The Background video layer is the normal video layer when mixing and switching with the HS-2850. It occupies the whole screen area of the Program output. This layer can be hidden or partly hidden by the PIP, DSK and LOGO layers in front of it.

The PIP 1 layer does not occupy the whole screen and is shown in front of the Background video layer when enabled. In some setups the PIP 1 image can be hidden behind the PIP 2 image. This is not a fault. Change the position or size of the PIP 1 or PIP 2 image if required.

The PIP 2 layer does not occupy the whole screen and is shown in front of the Background video and PIP 1 layers when enabled. In some setups the PIP 1 image can hide the PIP 2 image. Change the position or size of the PIP 2 or PIP 1 image if required.

The DSK 1 layer can occupy the whole screen. If set up incorrectly this layer can stop the video layers behind it from being seen properly. Re-adjust your DSK 1 settings or switch off the DSK1 function on the HS-2850 to restore the video behind it.

The DSK 2 layer can occupy the whole screen. If set up incorrectly this layer can stop the video layers behind it from being seen properly. Re-adjust your DSK 2 settings or switch off the DSK2 function on the HS-2850 to restore the video behind it.

The LOGO and Clock layer does not occupy the whole screen and all other layers are visible through it. A logo if positioned incorrectly can partially hide an important part of the video, PIP or CG LUMA KEY layers. Typically logos or station ID bugs are placed in a corner of the screen.

Note: Where possible prepare and position the upper video layer elements in advance of the live production starting to avoid them appearing on the program output incorrectly.

Most broadcast networks have guidelines and advice on the use of video, images, music, logos and on screen text so it is best to check beforehand when planning a production. Do not use copyright protected content until you have the relevant permissions. Information on royalty free video, images and music is widely available, speak to your local dealer or search for advice on the internet.

Page 58

Chapter 5 Audio Function

HDMI in Embedded Audio Pair

5.1 Overview

The HS-2850 has a simple, cost effective, audio switcher built in. This allows the HS-2850 to take audio from several sources either XLR analogue, SDI and/or HDMI inputs. This audio can be embedded onto the HDMI and SDI outputs and/or fed to the analogue XLR audio output connections.

You may de-embed audio from selected SDI or HDMI inputs and then connect this audio from the XLR outputs of the switcher to a separate external Audio Mixer, such as the Datavideo AM-100. Other audio sources such as microphones and background music can then be added at the AM-100.

Once the audio has been mixed externally in the AM-100 with any microphones or music sources it can then be fed back into the HS-2850 on the analogue XLR inputs. The HS-2850 can then embed this externally mixed audio on to the Program SDI and HDMI outputs.

5.2 Audio Menu Options – De-embedding SDI or HDMI audio

Using the following HS-2850 menu options, audio can be selected from the SDI or HDMI video inputs.

SDI Embedded Audio Set. Inputs 1 to 12 User choice of

Group 1,2,3 or 4 Pair 1 or 2

Input 4, 8 or 12 User choice of Group 1,2,3 or 4

Page 59

SDI Embedded Audio

Group

Stereo Pair

Channel

Embedded Channel No.

left

right

left

right

left

right

left

right

left

right

left

right

left

right

left

right

HDMI Embedded Audio

Stereo Pair

Channel

Embedded Channel No.

left

right

left

right

left

right

left

right

As each SDI / HD-SDI source can have up to sixteen channels of audio, and HDMI eight channels, we need to choose the audio channels with the options above and by using the following reference tables.

Stereo pair 1

Group 1

Stereo pair 2

Stereo pair 3

Group 2

Stereo pair 4

Group 3

Group 4

Stereo pair 5

Stereo pair 6

Stereo pair 7

Stereo pair 8

Stereo pair 1

Stereo pair 2

In some cases there may only be two channels of audio associated with the video: Group1, Stereo Pair 1.

Stereo pair 3

Stereo pair 4

Page 60

An external audio mixer is not required. If you just want to work with SDI / HDMI embedded

Tick selection of Program or Preview audio on the HDMI outputs.

audio, it is necessary to physically connect the switcher’s XLR outputs with the XLR inputs 1 and 2 to re-embed the audio again.

5.3 Audio Menu Options – Monitoring the audio levels

The HS-2850 can confirm the incoming audio levels by showing audio peak meters on the HDMI multi-view.

Audio level bars to Multi View Tick selection ON or OFF

It is also possible to hear the preview or program audio from the multi-view HDMI outputs using the menu option below.

Multi Screen Audio Indicators

Page 61

5.4 Audio Menu Options – Changing the audio input level

Level

Range -60 to +60

Nominal

Resets value to zero

The HS-2850 can change the incoming audio level on the video inputs by adjusting the following menu option.

Input Audio Settings

The audio level can also be changed at the external audio mixer if one is used.

5.5 Working with a fixed or single audio source

Example 1:

We have two mono mics (channels 1 & 2) connected to a HD camera. These embedded audio channels are then output from this camera, HD-SDI, to the HS-2850 switcher. If we want to only hear these two audio channels regardless of the video channel used then we would set up the switcher in the following way.

Open the Switcher Configuration Utility, click Settings Tab  Audio Tab and then click ‘+’ to expand the Audio XPT option. On the right pane of the window, set every input audio source to 1. Press the EXIT button to exit and save the audio settings.

After the new settings are saved, press the FIX/A+V button (WIPE area) to toggle between Audio Fixed and Audio-Follow-Video modes. Confirm that the AUDIO FIXED status has been selected by checking the status area of the HDMI multi-view. The status area is located just below or near the Preview image on the HDMI multi-view monitor. The button will be backlit red.

5.6 Switching between different embedded audio sources

Example 2:

We have two mono mics each connected to a different HD camera. The embedded audio is then output from each camera, HD-SDI, to the HS-2850 switcher. If we want to hear the audio from each camera as the video channels are switched, audio follows video, then we would set up in the following way.

Open the Switcher Configuration Utility, click Settings Tab  Audio Tab and then click ‘+’ to expand the Audio XPT option. On the right pane of the window, set input 1 audio source to 1, input 2 audio source to 2, input 3 audio source to 3 and etc. Press the EXIT button to exit and save the audio settings.

After the new audio settings have been saved successfully, select the AUDIO-F-VIDEO status with this button. Confirm the Audio-F-Video status by checking the status area of the HDMI multi-view. The status area is located just below or near the Preview image on the HDMI multi-view monitor. The button will be off.

While working in the Audio-F-Video mode, the audio sources will also change as the video sources are switched. We can choose how the audio will change sources, whether it be a clean

Page 62

cut (immediate switch) or some sort of transitioned change (cross fade or fade out & in). To

V type = Fade out A then fade in B

Follow auto audio mixing type (use above option)

By the end (clean cut or immediate audio switch)

do this we would need to set up with the following menu options.

X type X type = A/B cross fade

Auto Audio Mixing Type Tick selection of

V type

T-Bar Audio Mixing Type Tick selection of

5.7 Audio Delay

The HS-2850 switcher has a feature for Audio Delay up to 16 fields, or 8 frames. The audio delay is expressed in fields with a default setting of ‘02’ (2 fields / 1 frame) on each input until you change it.

Setting the Audio Delay

1. Power on HS-2850 Unit.

2. On the Preview bus, select the input that you would like to set Audio Delay.

3. Press any arrow key under the designated Menu row.

4. Press the Down Arrow [▼] key until “Input Audio Settings” is selected.

5. Press the Right Arrow [►] key to enter into the Input Audio Settings Menu.

6. Press the Right Arrow [►] key to enter the Audio Delay Setting Menu.

The default setting is 02; which is measured in fields. 2 fields = 1 frame.

7. Use the Arrow keys to set the number of fields, or frames. You can set the delay

from 1 to 16 fields, which is the equivalent of 1 to 8 frames.

8. When you have made your selection, press the Enter key

9. To Exit the Menu, press any key in the Program or Preview Bus.

* To set audio delay for all inputs: repeat the above steps for each individual input. Otherwise, the Audio Delay will remain at the default setting of 02.

Page 63

Chapter 6 Applications

6.1 Picture-In-Picture Function

The HS-2850 Picture in Picture function allows you to place one or two smaller PIP images over a chosen full size background image. The smaller PIP images can be set to pre-defined sizes and positioned almost anywhere within the Preview/Program screen area. These PIP windows can also have a coloured border applied, and can be brought into the production with a default PIP dissolve transition.

PIP Settings

Before trying to activate the PIP function it is best to understand how to set up or choose the right options for your production.

PIP Preset and PIP Program

When looking at the top right corner of the HS-2850 Control Panel / Keyboard there are four PIP keys. These are labelled Program and Preset.

The upper PIP1 and PIP2 keys relate to activating Picture In Picture images on the Program outputs.

The lower PIP1 and PIP2 keys relate to activating Picture In Picture images on the Multi-view or Preview outputs.

Assigning a video source input to a PIP Using the lower PIP1 or PIP2 buttons, you can assign a selected video input to the chosen PIP

video layer.

1. First press and hold down the required PIP button on the lower row. The Preset row of

input sources will light.

2. While still holding down the PIP button, press to select the required input from the Preset

row.

3. The input will flash to confirm it is selected.

This selection will also be confirmed on the HDMI Multi-view, with a P1 or P2 label shown next to the selected input image.

After successfully setting the PIP source, press the ENTER Key in the MENU area of the HS2850 keyboard. Navigate to the PIP Set Up option using the down arrow key. The PIP menu options provided here are:

Page 64

PIP Settings

Position PIP1

Border PIP2

X-Position (Left to right) = 000 to 097

Size PIP1

Border PIP1

Position PIP2

Size PIP2

Y-Position (Lower to Upper) = 000 to 108

PIP Size = 1 (small) to 33 (large)

Border Size = 0 (OFF), 1 (Thin) to 15 (Thick)

Border Color = 1 to 8 (user defined colours)

1=Yellow, 2=Cyan, 3=Green, 4=Magenta, 5=Red, 6=Blue

6.2 Down Stream Keyer

The HS-2850 has two Down Stream Keyers (DSK1, DSK2). This means it is able to take a key source video input and replace the white or black parts of this image with the video from another source. If the input video carries an alpha channel it is also possible to key in this way too.

DSK Settings

Before trying to activate the DSK function it is best to understand how to set up or choose the right options for your production well in advance of the production.

Assigning an input to a DSK channel for keying

Using the lower DSK1 or DSK2 buttons, you can assign a selected video input to the chosen DSK video layer.

1. First press and hold down the required DSK button on the lower row. The Preset row of

input sources will light.

2. While still holding down the DSK button, press to select the required input from the Preset

row.

3. The input will flash to confirm it is selected.

DSK Preset and DSK Program

When looking at the top right corner of the HS-2850 Control Panel / Keyboard there are four DSK keys. These are labelled Program and Preset.

The upper DSK1 and DSK2 keys relate to activating Down Stream Keying on the Program outputs.

The lower DSK1 and DSK2 keys relate to activating Down Stream Keying on the Multi-view or Preview outputs.

This selection will also be confirmed on the HDMI Multi-view, with a T1 or T2 label shown next to the selected input image.

After successfully configuring the down stream keyer settings, press the ENTER Key in the MENU area of the SE-2850 keyboard. Navigate to the DSK Settings option using the down arrow key. The DSK menu options provided here are:

Page 65

DSK Settings

Titles 1 (DSK1)

Titles 2 (DSK2)

Titles + a-CH mode (alpha channel mode)

Video Input Standard and Format

Input 4/8/12

CG-200

Character Generator

HS-2850 Digital Video Switcher

HDMI

Luma Key mode Luma Key Level 0 (black) to 255 (white)

6.3 HS-2850 and CG Setup

The CG-200 Character Generator software allows the producer to create professional overlays with a Windows laptop or Windows PC from which the CG-200 outputs a computer generated video stream via an HDMI interface. This software works in perfect pair with the HS-2850 if subtitles are a requirement in your production environment. Please follow the steps outlined below to set up the CG-200 Character Generator software with the HS-2850.

1. Connect your PC to Channel 4 or 8 of the HS-2850 (HDMI port) using an HDMI cable.

2. Open the HS-2850 OSD MENU to set Video Standard.

3. Select “Video Input Standard and Format”  “Input 4/8/12”  “HDMI COLOR MODE”  “CG-200 Mode”.

4. Activate Downstream Key on the HS-2850 Control Keyboard. Please see Section 6.2 Down

Stream Keyer for details.

5. Double click the CG-200 installation file icon to start installing the CG-200 Character Generator software on the PC.

6. Follow the installation wizard to install the CG software step by step and after the

HDMI COLOR MODE CG-200 MODE

Page 66

installation is complete, double click the program icon to open the CG software.

7. On the CG-200 User Interface, select Settings  Preference to open the Preference window on which you can choose the appropriate Video Mode (the video mode must be consistent with the HS-2850).

Page 67

8. Select a Demo file.

9. Enable HDMI Output.

10. Click Play all icon to start playing and streaming your CG contents.

Page 68

Chapter 7 Appendices

G0911D300413 Nyloc Machine Screw / ISO Round Head φ3.0*4m/m Nickel-Plated*2

G13307641201 VP-764 SE-2850 VIDIN Board Module (Dark Blue Fine Weave)*1

Appendix 1 Upgrading HS-2850 to 12 Channels

• Remove block panel and screws

G09220639022 VIDIN Block Panel SECC 1.0 VP-639 Painted Dark Blue Fine Weave 2-Plate Molding*1

• Insert the VIDIN board module

Page 69

• Lock the VIDIN board module in place with screws.

G0911D300413 Nyloc Machine Screw / ISO Round Head φ3.0*4m/m Nickel-Plated*2

Page 70

Appendix 2 Tally Outputs

The HS-2850 has a D-sub 25 pin female tally output

colour tally

number of other Datavideo

Dielectric strength: Max. DC 24V

Program 1

Open collector output

Tally output of input video Program 1

Program 2

Open collector output

Tally output of input video Program 2

Program 3

Open collector output

Tally output of input video Program 3

Program 4

Open collector output

Tally output of input video Program 4

Program 5

Open collector output

Tally output of input video Program 5

Program 6

Open collector output

Tally output of input video Program 6

Program 7

Open collector output

Tally output of input video Program 7

Program 8

Open collector output

Tally output of input video Program 8

Program 9

Open collector output

Tally output of input video Program 9

Program 10

Open collector output

Tally output of input video Program 10

Program 11

Open collector output

Tally output of input video Program 11

Program 12

Open collector output

Tally output of input video Program 12

GND

Ground

Preset 1

Open collector output

Tally output of input video Preset 1

Preset 2

Open collector output

Tally output of input video Preset 2

Preset 3

Open collector output

Tally output of input video Preset 3

Preset 4

Open collector output

Tally output of input video Preset 4

Preset 5

Open collector output

Tally output of input video Preset 5

Preset 6

Open collector output

Tally output of input video Preset 6

Preset 7

Open collector output

Tally output of input video Preset 7

Preset 8

Open collector output

Tally output of input video Preset 8

Preset 9

Open collector output

Tally output of input video Preset 9

Preset 10

Open collector output

Tally output of input video Preset 10

Preset 11

Open collector output

Tally output of input video Preset 11

Preset 12

Open collector output

Tally output of input video Preset 12

port. These connections provide bi-

Current: Max. 50mA

information to a products, such as the ITC-100 eight channel talkback system and the TLM range of LCD Monitors.

These ports are open collector ports and as such do not provide power to tally light circuits.

The pin outputs are defined as follows:

Pin No. Signal name Input/Output Signal Description

Page 71

Appendix 3 GPI / GPO Connections

The HS-2850 can control external recorder/playback devices like the HDR-60 and HDR-70 via a simple contact closure GPI / GPO switch.

The GPI interface is a 3.5mm Jack Socket which is situated on the rear panel of the HS-2850. Contact closure between the Outer and Inner contacts on the jack plug will trigger a user selected event. Power is supplied by the HS-2850 and is less than 5V DC.

This GPI socket can also be used as a GPO socket to trigger record or playback events with other equipment such as the Datavideo HDR-70 recorder.

SAFETY FIRST The cabling required needs to be designed specifically to connect the HS-2850 to the chosen record or playback device as they are not all the same. The cabling required can be made by yourself or a competent technician. Please speak with your Dealer or local Datavideo office to get further help and advice.

Page 72

Appendix 4 Firmware Update

rear panel and the Windows 7

to locate.

5. Double click the firmware update icon to launch the Flash Update Utility.

6. Confirm the supported devices list says SE-2850 then click NEXT.

Datavideo usually releases new firmware containing new features or reported bug fixes from time to time. Customers can either download the HS-2850 firmware as they wish or contact their local dealer or reseller for assistance.

This section outlines the firmware upgrade process which should take approximately 1 hour 20 minutes to complete.

The existing HS-2850 settings should persist through the firmware upgrade process, which should not be interrupted once started as this could result in a non-responsive unit.

Successful firmware upgrade on HS-2850 requires:

 The latest firmware update file for the HS-2850 (This can be obtained from your local

Datavideo office or dealer).

 The HS-2850 power adapter.  The SEConfig software.  A Windows 7 computer with an Ethernet port.  An Ethernet cable.

Keyboard Firmware Update

1. Switch off or shut down the HS-2850 and Computer in the normal way.

2. Connect the Ethernet cable between the HS-2850

Computer.

3. Turn on the Windows 7 Computer.

4. Unzip the firmware update folder to the Computer Desktop so the file within it is easy

Page 73

Updating the SE-2850 firmware:

7. The following window will be

Device is

then click

8. POWER ON the SE-2850 and as soon

Automatically update the

Click the Yes button to confirm you wish to perform the firmware update when you

displayed. Select

connected via Ethernet NEXT.

as it is discovered by the Computer, select “ device to latest firmware version” then click NEXT.

see the prompt window “Do you really want to perform firmware update?”.

10. The update process will begin and two progress bars will be shown. The lower bar,

Total Progress, will take around 15 minutes to complete.

11. Once this process is complete close the application and power cycle the SE-2850.

The firmware is now updated, but please continue with the following steps in order to complete the switcher’s update process.

12. Install the SEConfig software on to the Computer. When the SE-2850 has restarted,

double click the SEConfig dv icon to launch the second part of the update process.

Page 74

13. If you immediately get an error

window, do not worry, click OK. This

14. Press PC Control button so it is ON in

15. Select Ethernet to display the

Computer’s IP Address. Click the

drop down list. The first three

in the top right

corner. The process will take

approximately 45 minutes to

17. The next step will be to re-calibrate the SE-2850 T-Bar to get it working correctly.

simply means that the PC CTRL button in the menu area of the SE2850 control keyboard has not been enabled.

the MENU area of the SE-2850 keyboard.

Find button to find and display the SE-2850 Switcher’s IP Address in the

numbers in both IP addresses should match. See below example.

16. Click Connect and then click Restore

Factory Settings hand

complete.

Page 75

T-Bar Re-Calibration

4. Power ON the HS-2850 switcher while still

holding down the buttons in step 3.

After a firmware update of the switcher it will be necessary to re-calibrate the T-Bar to get it working correctly.

1. Move the T-Bar to its lowest position.

2. Power OFF the HS-2850 switcher.

3. Press and hold down button 1 on both the

Program and Preset rows of the switcher’s keyboard.

5. The switcher will start but the keyboard lights will

remain dead except for the T-Bar progress LEDs. When these LEDs flash ON and OFF release the buttons from step 3.

6. Move the T-Bar to almost its top position (2-

3mm away) and then press the CUT button.

9. Ensure the TIMER button is OFF.

7. Move the T-Bar back to almost its lowest

position (2-3mm away) and then press the AUTO TAKE button.

8. To exit the calibration procedure, press the

CLOCK button.

10. Test the T-Bar. If necessary change the T-Bar

Mode in the OSD MENU options.

Page 76

Monitor Firmware Update

Requirements

• The latest firmware update for the HS-2850 Monitor.

This firmware file can be obtained from your local Datavideo office or dealer.

• USB 2.0 pen drive 128MB or larger with a USB A connector.

How to update the firmware

1. Unzip / extract the supplied zipped archive or rar folder.

2. Delete the contents of the USB 2.0 pen drive so it is empty.

3. Transfer / copy the unzipped / extracted file to the USB 2.0 pen drive; make sure the

file name is renamed to MSTFLASH.bin.

4. Plug the USB 2.0 pen drive into the USB 2.0 port labelled MONITOR F/W UPGRADE on

the front of the monitor button panel.

5. Reboot HS-2850 and the update will be automatically in progress.

6. The HS-2850 Monitor will reboot itself at the end of the process.

Page 77

Appendix 5 Frequently-Asked Questions

No.

Problems

Solutions

Corrupted images are seen in small

In the HS-2850, each input source must be associated with only one button. If you

more than

Multiview display. To avoid this

please make sure your XPT setting is

configuration.

I have enabled the TIMER feature

the countdown timer isn’t

After the TIMER button is enabled on the selected PGM channel, the countdown

channel.

Audio and video are not synced.

In this case, the Video XPT feature might

avoid out-of-sync audio and video.

I am seeing jitters in MV audio level indicator.

Check the audio input as this could be due an absence of the audio input.

I hear noise on input channels 5 to 8 after I have changed the

This can occur as a result of frame rate

your machine.

Brightness of keys is too bright or

Please press the Enter key on the MENU

menu will show on the screen. Please select the Brightness option in the OSD

equals to high

Options.

This section describes problems that you may encounter while using HS-2850. If you have any questions, please refer to related sections and follow all suggested solutions. If problem still exists, please contact your distributor or the service center.

windows of the HS-2850 Multiview display.

on the selected PGM channel but

counting down.

associate one source to one button, you will then see corrupted images in small windows of the HS2850

configured to the one input to one button

timer will start on the PGM display as soon as the user switches to the selected PGM

have been activated and if Audio is set to FIX, the Audio XPT must also be enabled to

change (for example 1080i50  1080i59).

resolution.

too dark.

To correct this issue, please factory reset

area of the keyboard. After that, the OSD

menu. The key brightness can be defined by the user from level 1 to level 4. 1 equals to high brightness/4 brightness. For details, please refer to Keys

Brightness in the chapter 2.2.7 OSD MENU

Page 78

Appendix 6 Dimensions & Weight

All measurements in millimeters (mm) Weight: 18.7 Lbs (8.5 Kg)

Page 79

Appendix 7 Specifications

Switcher System

Connections

Total 12 CH inputs 12 HD/SD SDI and 3 HDMI selectable

Total Outputs

3 HD/SD SDI and 1 HDMI

Monitor Input for External device

Analog Audio Input

4Ch Balanced XLR

Analog Audio Output

2Ch Balanced XLR

Ref Input / Output

1xBNC Ref in / 1xBNC Ref out (loop-through)

Internal Frame Synchronizers

One of the input signals (AUX)

Audio Indicator on Multi view

Each Video input embedded Audio (2 Ch) + Preview (2 Ch)+ Program (4 Ch)

Tally Out

D-Sub 25 pin

GPI

Two mode: Level /Pulse trigger selectable

• F/W Upgrade

Remote control

D-Sub 9 pin connector

RS-422 Remote Control

Power Input

12V DC

Standards

Input: HD : 1080p 25/29.97/30/50/59.94/60Hz

Output: 1080i 50/59.94/60Hz

Video Sampling

4:2:2 10bit

Color Precision

4:2:2 10bit

Color Space

4:2:2 YUV

Aspect Converter

Output SD 16:9 or 4:3

Digital Audio Resolution

Extras

Downstream Keyers

Linear/Luma Keyers

Total Video Inputs

1 HDMI

12 All Inputs

PGM Out SDI

Multi view Out In SD/HD mode ; MV output by HDMI is 1920x1080P resolution

• Program

Output can select any of input source

• Preview

• Program without logo overlay

• Program without logo overlay and without subtitles.

•

Ethernet (RJ45)

Format Support

• Upload Still image

• Logo insert

•

1080I 50/59.94/60Hz 720p 50/59.94/60Hz SD: 576i 50Hz, 480i 59.94Hz

24 bit

Page 80

Pattern Generators

Color Bar

Effect

Transition, Split, WIPE, MIX, FTB, CUT

Picture in Picture

2, Shape, Border

Logo insertion

TC-200 Build In

Yes

Monitor System

LCD Display

17.3” TFT LCD

Resolution

RGB 1600 x 900 pixel

Aspect Ratio

4:3 and 16:9 selectable

LED Life time

15,000 hrs. (approx.)

Brightness (Luminance)

220 cd/m²

Contrast Ratio

650:1

View Angle

Top : 20 deg / Bottom : 45 deg Left : 45 deg / Right : 45 deg

Video System

NTSC / PAL auto recognition

Color Adjustment

Brightness, Contrast, Color Saturation

Intercom System

Connections

3.5mm Stereo Jack Socket for combination Headphone /

Headset Impedance 8~600 ohms 100mW(min)

¼” ( 6.3mm ) Stereo Headphone Socket Headset Impedance 8~600 ohms 100mW(min)

3 Pin XLR / ¼” (6.3mm) Jack Microphone Socket Switchable

Microphone Sensitivity Level : -67dB

Speaker Volume Control

Control Knob

Communication interface

8 channels 5 pin XLR

Frequency Response

550-3.6KHz, < +/-3dB

THD

< 3%

S/N

> 50dB

Built-in Speaker

70mm x 30mm 32 Ohm 3 Watts

ITC-100SL Specification

Input

5 Pin XLR Connector

3.5mm Stereo Jack Socket for combination Headphone /

Motorola Mobile Phone type headset / microphone

Tally Out Socket

3.5mm Jack Socket to connect to TD-2 Tally Indicator

Tally LED

Bi-Colour LED – RED indicates LIVE / GREEN Indicates CUED

Power LED

Illuminates to indicate that power is being received

MIC / Headset

Headphone

Microphone

MIC / Headset Socket

Microphone

Condenser / Dynamic Input.

Microphone Headset Impedance 8~600 ohms 100mW(min) Microphone Level -67Db or 2.5mm Stereo Jack Socket, for

Page 81

DATAVIDEO WORLDWIDE OFFICES

Service & Support

It is our goal to make owning and using Datavideo products a satisfying experience. Our support sta󰀨 is available

to assist you to set up and operate your system. Contact your local office for specific support requests. Plus, please visit www.datavideo.com to access our FAQ section.

China Shanghai

Datavideo Technologies China Co 601,Building 10,No.1228, Rd.Jiangchang, Jingan District,Shanghai Tel: +86 21-5603 6599 Fax:+ 86 21-5603 6770 E-mail: service@datavideo.cn

China Beijing

Datavideo Technologies China Co No. 812, Building B, Wankai Center,

No.316, Wan Feng Road, Fengtai District, Beijing, China Tel: +86 10-8586 9034 Fax:+86 10-8586 9074 E-mail: service@datavideo.cn

China Chengdu

Datavideo Technologies China Co B-823,Meinian square,No.1388, Middle of Tianfu Avenue,Gaoxin District, Chengdu,Sichuan Tel: +86 28-8613 7786 Fax:+86 28-8513 6486 E-mail: service@datavideo.cn

China Fuzhou

Datavideo Technologies China Co A1-2318-19 Room,No.8, Aojiang Road, Taijiang District,Fuzhou,Fujian,China

Tel: 0591-83211756，0591-83210187 Fax:0591-83211262 E-mail: service@datavideo.cn

China Jinan

Datavideo Technologies China Co

902, No. 1 business building, Xiangtai Square, No. 129, Yingxiongshan Road, Shizhong District, Jinan City, Shandong Province, China

Tel: +86 531-8607 8813

E-mail: service@datavideo.cn

Hong Kong

Datavideo Hong K ong Ltd

G/ F.,26 Cross Lane Wanchai, Hong Kong

Tel: +852-2833-1981 Fax:+ 852-2833-9916 E-mail: info@dat avideo.com.hk

India Noida

Datavideo India Noida A-132, Sec-63,Noida-201307,

India

Tel: +91-0120-2427337 Fax:+91-0120-2427338 E-mail: sales@datavideo.in

India Kochi

Datavideo India Kochi

2nd Floor- North Wing, Govardhan Building, Opp. NCC Group Headquaters, Chittoor Road, Cochin- 682035

Tel: +91 4844-025336 Fax:+91 4844-047696

Netherlands

Data video Technologies Europe B V Floridadreef 106 3565 AM Ut rech t, Th e Netherlands Tel: +31-30-261-9 6-56 Fa x: +31-30-261-9 6-57 E-mail: info@dat av ideo.n l

Singapore

Datavideo Visual Technology(S) Pte Ltd No. 178 Paya Lebar Road #06-07 Singapore 409030

Tel: +65-6749 6866 Fa x:+65-6749 3266 E-mail:info@datavideovirtualset.com

Singapore

Data video Technologies (S ) PTE Lt d No. 178 Paya Lebar Road #06-03 Singapore 409030

Tel: +65-6749 6866 Fa x:+65-6749 3266 E-mail:s ales@dat av ideo.sg

Taiwan

Datavideo Technologies Co. Lt d 10F. No. 176, Jian 1st Rd.,Chung Ho

District, New Taipei City 235, Taiwan

Tel: +886-2-8227-2888

Fax:+886-2-8227-2777 E-mail:service@dat avideo.com.tw

United States

Datavideo Corporat ion 7048 Elmer Avenue. Whittier, C A 90602, U.S.A. Tel: +1-562-696 2324 Fax:+1-562-698 6930 E-mail:sales@datavideo.comE-mail: sales@datavideo.in

United Kingdom

Data video U K Limi te d Brookfield House, Brookfield Industrial Estate, Peakdale Road, Glossop, Derbyshire, SK13 6LQ Tel: +44-1457 851 000 Fa x: +44-1457 850 964 E-mail: sales@dat avideo.co. uk

France

Datavideo France s.a.r.l. Cité Descartes 1, rue Albert Einstein Champs sur Marne 774477 – Marne la Vallée cedex 2 Tel: +33-1-60370246 Fa x: +33-1-60376732 E-mail: info@datavideo.fr

Please visit our website for latest manual update.

www.datavideo.com/product/HS-2850

Jul-05.2017

Datavideo HS-2850-12 Instructions

Specifications and Main Features

Frequently Asked Questions

User Manual

Table of Contents

Warnings and Precautions

Warranty

Standard Warranty

Three Year Warranty

Disposal

Chapter 1 Introduction

1.1 Features

1.2 System Diagram

Chapter 2 Connections and Controls

2.1 Main Unit – Rear Panel Overview

2.1.1 Rear Panel Connections

2.2 Control Panel Overview

2.2.1 Video Switching

Program and Preset rows

Background

2.2.2 Video Transitions

Transition Selection

Triggering the Transition

2.2.3 Logo and Clock

2.2.4 Picture-in-Picture and Downstream Key

2.2.5 Frame Store and Audio Control

2.2.6 Crosspoint

2.2.7 OSD MENU Options

2.2.8 PC Control – SE Remote Control Software

SET Function

REC & PLAY Functions

Software-based Macro Functions

TIME Function

2.3 Intercom & Monitor Control Panel

2.3.1 Intercom Function

2.3.2 Monitor Function

2.3.3 Monitor Menu Options

MAIN ADJUST

COLOR

Information

Special Function

Factory Reset

Chapter 3 Switcher Configuration Utility (SEConfig Software)

3.1 Network Setup

3.2 Connecting the SEConfig Software to the Switcher

3.2.1 Change the Switcher IP Address

3.3 Switcher tab

3.3.1 Profiles

3.4 Settings tab

3.4.1 Inputs tab

3.4.2 Audio Tab

3.4.3 Video XPT Tab

3.4.4 Common Setup

3.4.5 Outputs Tab

3.5 Images Upload tab

3.5.1 Still Pictures

3.5.2 Logos

3.5.3 Dynamic Logo

3.6 Multi screen window signs (labels) tab

3.7 Multiview Layout Tab

3.8 Multiview Upload Tabs (A / B / C)

Chapter 4 Switcher Video

4.1 HDMI Multi-View

4.2 Video Layers

Chapter 5 Audio Function

5.1 Overview

5.2 Audio Menu Options – De-embedding SDI or HDMI audio

5.3 Audio Menu Options – Monitoring the audio levels

5.4 Audio Menu Options – Changing the audio input level

5.5 Working with a fixed or single audio source

5.6 Switching between different embedded audio sources

5.7 Audio Delay

Chapter 6 Applications

6.1 Picture-In-Picture Function

6.2 Down Stream Keyer

6.3 HS-2850 and CG Setup

Chapter 7 Appendices

Appendix 1 Upgrading HS-2850 to 12 Channels

Appendix 2 Tally Outputs

Appendix 3 GPI / GPO Connections