Datavideo HS-2850 User Manual
HD/SD 12-CHANNEL
PORTABLE VIDEO STUDIO
HS-2850
( 8 / 12 CHANNEL )
Instruction manual
Table of Contents
WARNINGS AND PRECAUTIONS ........................................................................................ 5
WARRANTY ...................................................................................................................... 6
STANDARD WARRANTY ................................................................................................................. 6
THREE YEAR WARRANTY ............................................................................................................... 6
DISPOSAL ......................................................................................................................... 7
CHAPTER 1 INTRODUCTION ............................................................................................ 8
1.1 FEATURES ....................................................................................................................... 8
1.2 SYSTEM DIAGRAM .......................................................................................................... 10
CHAPTER 2 CONNECTIONS AND CONTROLS .................................................................. 11
2.1 MAIN UNIT – REAR PANEL OVERVIEW ............................................................................... 11
2.1.1 Rear Panel Connections ......................................................................................... 11
2.2 CONTROL PANEL OVERVIEW ............................................................................................. 15
2.2.1 Video Switching ..................................................................................................... 15
Program and Preset rows ............................................................................................. 15
Background ................................................................................................................... 16
2.2.2 Video Transitions ................................................................................................... 16
Transition Selection ...................................................................................................... 16
Triggering the Transition ............................................................................................... 17
2.2.3 Logo and Clock ....................................................................................................... 18
2.2.4 Picture-in-Picture and Downstream Key ................................................................ 19
2.2.5 Frame Store and Audio Control ............................................................................. 20
2.2.6 Crosspoint .............................................................................................................. 20
2.2.7 OSD MENU Options ............................................................................................... 21
2.2.8 PC Control – SE Remote Control Software ............................................................. 25
SET Function .................................................................................................................. 26
REC & PLAY Functions ................................................................................................... 27
Software-based Macro Functions ................................................................................. 27
TIME Function ............................................................................................................... 27
2.3 INTERCOM & MONITOR CONTROL PANEL ........................................................................... 27
2.3.1 Intercom Function .................................................................................................. 28
2.3.2 Monitor Function ................................................................................................... 29
2.3.3 Monitor Menu Options .......................................................................................... 30
MAIN ADJUST ................................................................................................................ 31
COLOR ........................................................................................................................... 31
Information ................................................................................................................... 31
Special Function ............................................................................................................ 32
Factory Reset ................................................................................................................ 32
CHAPTER 3 SWITCHER CONFIGURATION UTILITY (SECONFIG SOFTWARE) ..................... 33
2
3.1 NETWORK SETUP ............................................................................................................ 33
3.2 CONNECTING THE SECONFIG SOFTWARE TO THE SWITCHER ......................................................... 36
3.2.1 Change the Switcher IP Address ............................................................................ 37
3.3 SWITCHER TAB ............................................................................................................... 38
3.3.1 Profiles ................................................................................................................... 39
3.4 SETTINGS TAB ................................................................................................................ 39
3.4.1 Inputs tab ............................................................................................................... 39
3.4.2 Audio Tab ............................................................................................................... 40
3.4.3 Video XPT Tab ........................................................................................................ 43
3.4.4 Common Setup ....................................................................................................... 45
3.4.5 Outputs Tab ........................................................................................................... 48
3.5 IMAGES UPLOAD TAB ...................................................................................................... 49
3.5.1 Still Pictures............................................................................................................ 49
3.5.2 Logos ...................................................................................................................... 50
3.5.3 Dynamic Logo ........................................................................................................ 51
3.6 MULTI SCREEN WINDOW SIGNS (LABELS) TAB ....................................................................... 52
3.7 MULTIVIEW LAYOUT TAB ................................................................................................. 53
3.8 MULTIVIEW UPLOAD TABS (A / B / C) ............................................................................... 54
CHAPTER 4 SWITCHER VIDEO ....................................................................................... 55
4.1 HDMI MULTI-VIEW ....................................................................................................... 55
4.2 VIDEO LAYERS ................................................................................................................ 56
CHAPTER 5 AUDIO FUNCTION ...................................................................................... 58
5.1 OVERVIEW .................................................................................................................... 58
5.2 AUDIO MENU OPTIONS – DE-EMBEDDING SDI OR HDMI AUDIO ............................................ 58
5.3 AUDIO MENU OPTIONS – MONITORING THE AUDIO LEVELS .................................................... 60
5.4 AUDIO MENU OPTIONS – CHANGING THE AUDIO INPUT LEVEL ................................................ 60
5.5 WORKING WITH A FIXED OR SINGLE AUDIO SOURCE ............................................................... 61
5.6 SWITCHING BETWEEN DIFFERENT EMBEDDED AUDIO SOURCES ................................................. 61
5.7 AUDIO DELAY ................................................................................................................ 62
CHAPTER 6 APPLICATIONS ........................................................................................... 63
6.1 PICTURE-IN-PICTURE FUNCTION ........................................................................................ 63
6.2 DOWN STREAM KEYER .................................................................................................... 64
6.3 HS-2850 AND CG SETUP ................................................................................................ 64
CHAPTER 7 APPENDICES ............................................................................................... 68
APPENDIX 1 UPGRADING HS-2850 TO 12 CHANNELS .................................................................... 68
APPENDIX 2 TALLY OUTPUTS ...................................................................................................... 70
APPENDIX 3 GPI / GPO CONNECTIONS ....................................................................................... 72
APPENDIX 4 RS-422 PHYSICAL CONNECTION ................................................................................ 73
APPENDIX 5 FIRMWARE UPDATE ................................................................................................. 74
Keyboard Firmware Update.............................................................................................. 74
3
T-Bar Re-Calibration ......................................................................................................... 77
Monitor Firmware Update ................................................................................................ 78
APPENDIX 6 FREQUENTLY-ASKED QUESTIONS ................................................................................ 79
APPENDIX 7 DIMENSIONS & WEIGHT........................................................................................... 80
APPENDIX 8 SPECIFICATIONS ...................................................................................................... 81
SERVICE AND SUPPORT .................................................................................................. 84
Disclaimer of Product & Services
The information offered in this instruction manual is intended as a guide only. At all times,
Datavideo Technologies will try to give correct, complete and suitable information. However,
Datavideo Technologies cannot exclude that some information in this manual, from time to
time, may not be correct or may be incomplete. This manual may contain typing errors,
omissions or incorrect information. Datavideo Technologies always recommend that you
double check the information in this document for accuracy before making any purchase
decision or using the product. Datavideo Technologies is not responsible for any omissions
or errors, or for any subsequent loss or damage caused by using the information contained
within this manual. Further advice on the content of this manual or on the product can be
obtained by contacting your local Datavideo Office or dealer.
4
FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Warnings and Precautions
1. Read all of these warnings and save them for later reference.
2. Follow all warnings and instructions marked on this unit.
3. Unplug this unit from the wall outlet before cleaning. Do not use liquid or aerosol
cleaners. Use a damp cloth for cleaning.
4. Do not use this unit in or near water.
5. Do not place this unit on an unstable cart, stand, or table. The unit may fall, causing
serious damage.
6. Slots and openings on the cabinet top, back, and bottom are provided for ventilation. To
ensure safe and reliable operation of this unit, and to protect it from overheating, do not
block or cover these openings. Do not place this unit on a bed, sofa, rug, or similar
surface, as the ventilation openings on the bottom of the cabinet will be blocked. This
unit should never be placed near or over a heat register or radiator. This unit should not
be placed in a built-in installation unless proper ventilation is provided.
7. This product should only be operated from the type of power source indicated on the
marking label of the AC adapter. If you are not sure of the type of power available,
consult your Datavideo dealer or your local power company.
8. Do not allow anything to rest on the power cord. Do not locate this unit where the
power cord will be walked on, rolled over, or otherwise stressed.
9. If an extension cord must be used with this unit, make sure that the total of the ampere
ratings on the products plugged into the extension cord do not exceed the extension
cord rating.
10. Make sure that the total amperes of all the units that are plugged into a single wall
outlet do not exceed 15 amperes.
11. Never push objects of any kind into this unit through the cabinet ventilation slots, as
they may touch dangerous voltage points or short out parts that could result in risk of
fire or electric shock. Never spill liquid of any kind onto or into this unit.
12. Except as specifically explained elsewhere in this manual, do not attempt to service this
product yourself. Opening or removing covers that are marked “Do Not Remove” may
expose you to dangerous voltage points or other risks, and will void your warranty. Refer
all service issues to qualified service personnel.
13. Unplug this product from the wall outlet and refer to qualified service personnel under
the following conditions:
a. When the power cord is damaged or frayed;
b. When liquid has spilled into the unit;
c. When the product has been exposed to rain or water;
d. When the product does not operate normally under normal operating conditions.
Adjust only those controls that are covered by the operating instructions in this
manual; improper adjustment of other controls may result in damage to the unit and
5
may often require extensive work by a qualified technician to restore the unit to
normal operation;
e. When the product has been dropped or the cabinet has been damaged;
f. When the product exhibits a distinct change in performance, indicating a need for
service.
Warranty
Standard Warranty
Datavideo equipment are guaranteed against any manufacturing defects for one year
from the date of purchase.
The original purchase invoice or other documentary evidence should be supplied at the
time of any request for repair under warranty.
The product warranty period begins on the purchase date. If the purchase date is
unknown, the product warranty period begins on the thirtieth day after shipment from a
Datavideo office.
All non-Datavideo manufactured products (product without Datavideo logo) have only
one year warranty from the date of purchase.
Damage caused by accident, misuse, unauthorized repairs, sand, grit or water is not
covered under warranty.
Viruses and malware infections on the computer systems are not covered under
warranty.
Any errors that are caused by unauthorized third-party software installations, which are
not required by our computer systems, are not covered under warranty.
All mail or transportation costs including insurance are at the expense of the owner.
All other claims of any nature are not covered.
All accessories including headphones, cables, and batteries are not covered under
warranty.
Warranty only valid in the country or region of purchase.
Your statutory rights are not affected.
Three Year Warranty
All Datavideo products purchased after July 1st, 2017 are qualified for
a free two years extension to the standard warranty, providing the
product is registered with Datavideo within 30 days of purchase.
Certain parts with limited lifetime expectancy such as LCD panels,
DVD drives, Hard Drive, Solid State Drive, SD Card, USB Thumb Drive, Lighting, Camera
module, PCIe Card are covered for 1 year.
The three-year warranty must be registered on Datavideo's official website or with your
local Datavideo office or one of its authorized distributors within 30 days of purchase.
6
Disposal
For EU Customers only - WEEE Marking
This symbol on the product or on its packaging indicates that this
product must not be disposed of with your other household waste.
Instead, it is your responsibility to dispose of your waste equipment by
handing it over to a designated collection point for the recycling of waste
electrical and electronic equipment. The separate collection and
recycling of your waste equipment at the time of disposal will help to conserve natural
resources and ensure that it is recycled in a manner that protects human health and the
environment. For more information about where you can drop off your waste equipment
for recycling, please contact your local city office, your household waste disposal service or
the shop where you purchased the product.
CE Marking is the symbol as shown on the left of this page. The letters
"CE" are the abbreviation of French phrase "Conformité Européene"
which literally means "European Conformity". The term initially used was
"EC Mark" and it was officially replaced by "CE Marking" in the Directive
93/68/EEC in 1993. "CE Marking" is now used in all EU official documents.
7
Chapter 1 Introduction
The HS-2850 is an 8 channel 10-bit 1920 x 1080i & cost-effective, broadcast-quality mobile
hand carry switcher. Featuring 8 digital, it is designed for live events and TV programs that
need to blend a variety of video and audio sources. HS-2850 is light weight, portable and
powerful features for mobile switcher solution.
As a complete AV package, the HS-2850 HD mobile studio enables users to switch
seamlessly between video and audio sources and blend high-quality digital content on the
fly.
Advanced features include a 17.3-inch multi-image video monitor which displays multiple
sources, as well as preview and program.
The system is equipped with an eight way intercom system and is supplied with four belt
packs for effective communication between the whole production crew.
The HS-2850 is ideal for TV and video professionals working in outside broadcast or
temporary video studios, such as theatres or conference centres. The HS-2850 is also a great
value solution for the worship, education and AV market.
That’s Datavideo, sharing the value!
1.1 Features
Supports 8 or 12 HD or SD Inputs in a variety of configurations:
HD Mode
- 8 / 12 HD-SDI
- 6 / 9 HD-SDI + 2 / 3 HDMI
SD Mode
- 8 / 12 SD-SDI
- 6 / 9 SDI + 2 / 3 HDMI
- 4 SDI
- 4 SDI + 2 HDMI
3 SDI Outputs assignable to:
- AUX
- Program (PGM)
- Preview (PVW)
- PGM clean
1 HDMI outputs for multi view monitoring
Audio I/O
- Input: 4 analogue balanced XLR
- Output: 2 analogue balanced XLR.
- Supports embedded audio SDI output from 4-CH XLR Audio input
8
Dual PIP displays with user-defined borders and positions
Two DSK with a setup choice of basic Luma Key or Alpha Channel
Built-in title overlay system (TC-200) that works with CG systems (see Section 6.4)
Cut, Mix and Wipe with borders
Logo and Clock on screen
Cross Point Assignment (XPT)
Audio delay for each de-embedded audio source
OSD SMPTE/ EBU Audio options
Black burst PAL or Tri-Level Sync Reference
Countdown counter on multi screen
Tally, GPI interface and RJ45 for firmware upgrade
Built-in 8 Channel Intercom System
DC 12V operation voltage, available for mobile use
One 17.3-inch monitor with a resolution of 1600x900 dots
9
1.2 System Diagram
10
Chapter 2 Connections and Controls
1.
Input 1 – SD / HD-SDI
14.
User Defined SDI Outputs 1~3
2.
Input 2 – SD / HD-SDI
15.
Sync Output / Ref Loop
3.
Input 3 – SD / HD-SDI
16.
User Defined Multi view Output
4.
Input 4 – SD / HD-SDI / HDMI
17.
Ethernet port for PC control & updates
5.
Input 5 – SD / HD-SDI
18.
Tally Output connector
6.
Input 6 – SD / HD-SDI
19.
GPI connector
7.
Input 7 – SD / HD-SDI
20.
RS-422 connector
8.
Input 8 – SD / HD-SDI / HDMI
21.
4pin XLR Power Input connector
9.
Input 9 – SD / HD-SDI**
22.
Power Switch
10.
Input10 – SD / HD-SDI**
23.
3pin XLR Audio Inputs
11.
Input11 – SD / HD-SDI**
24.
3pin XLR Audio Outputs
12.
Input12 – SD / HD-SDI / HDMI**
25.
Monitor HDMI IN (External Video Input)
13.
External Sync Input
26.
To Beltpack
Video Input Modules (1 – 12)
The HS-2850 can be supplied with eight or
twelve video input channels.
An HS-2850 with eight input channels (Input
1 to 8) has two video input modules
installed.
There are four video input channels on each
Video Input Module. Each Video Input
Module (shown left) has the same
connections, four BNC connectors and one
13
14
15
16
17
18
19
20
21
22
23
24
26
25
2.1 Main Unit – Rear Panel Overview
** Please note inputs 9 to 12 are not present if you have purchased the eight channel HS-
2850. Eight channel units can be upgraded to twelve inputs, please speak with your local
dealer.
2.1.1 Rear Panel Connections
11
HDMI port. The fourth BNC connector and
the HDMI port are an option for the same
input channel.
An HS-2850 with twelve input channels has
three video input modules installed. An eight
channel unit can be upgraded to twelve
inputs by adding another Video Input
Module (Input 9 to 12).
SD Inputs
SDI
BNC
HDMI
1, 5 & 9
Yes
---
2, 6 & 10
Yes
---
3, 7 & 11
Yes
---
4, 8 & 12
Yes
Yes
1920x1080i
HD Inputs
HD-SDI
BNC
HDMI
1, 5 & 9
Yes
---
2, 6 & 10
Yes
---
3, 7 & 11
Yes
---
4, 8 & 12
Yes
Yes
The two tables, on the left, show which types
of video inputs can be connected to the HS2850 switcher. For example, only input
channels 4, 8 and 12 have the HDMI input
option.
NOTE: This switcher cannot accept 1080P or
1280x720P or 1440x1080i inputs and has no
computer input scaling options.
SYNC I/O (13 / 15)
The HS-2850 can be synchronized with other
studio equipment such as cameras and
House sync. Input BNC (13) will accept House
sync or Tri-level sync. Output BNC (15) can
be used to pass the sync signal to other
studio equipment such as cameras or
recorders.
HDMI MULTIVIEW OUT (16)
The HS-2850 has one HDMI outputs (16)
which can be used to display a preset
combination of inputs plus program and
preset.
See the section on HDMI Multi-View for the
five preset multi-view options.
12
SDI VIDEO OUTPUTS (14)
The three BNC output connectors (14) are
user defined SDI outputs. Each of these SDI
outputs has the option to be:
1. Program output
2. Preview output
3. Program output without logo
4. Program output without logo and DSK
5. Aux output of a selected input channel
SDI outputs 2 and 3 also have the option to
be a Program output which has been
downscaled from HD to SD resolution.
ETHERNET PORT (17)
This RJ45 Ethernet port (17) is used to
connect the HS-2850 to a PC for remote
control, or to update the unit’s firmware, or
to configure the switcher. See Chapter 3 for
more details.
AUDIO OUT (24)
Supports two channels of the XLR Balanced
Audio output.
See Chapter 5 Audio Function for more
details.
AUDIO IN (23)
Supports four channels of the XLR Balanced
Audio Input.
See Chapter 5 Audio Function for more
details.
TALLY OUT (18)
The HS-2850 Tally Output port provides bicolour tally information to a number of other
Datavideo products, such as the ITC-100
eight channel talkback system or the
Datavideo TLM range of monitors.
See Appendix 1 for more details.
13
GPI (19)
The GPI socket can be used for simple
external control.
See Appendix 2 for more details.
RS-422 REMOTE (20)
In addition to the Ethernet port for remote
control, you can also connect your PC to this
port for controlling the HS-2850 with the SE
Remote software. See Section 2.2.8 SE
Remote Control Software for details.
Please check with your local Datavideo office
for advice on this connection or refer to
Appendix 4 of this manual for RS-422 PIN
definitions and cable wiring.
DC IN (21)
Connect the supplied 12V 5A PSU to this 4pin
XLR socket.
Pin 1 = GND ( - )
Pin 2 = NC
Pin 3 = NC
Pin 4 = VCC ( + )
Power Switch (22)
The power switch turns ON/OFF the unit.
TO BELTPACK (26)
Intercom Channel Input / Output XLR Sockets
Each of the 8 channels has an XLR connector that carries bi-directional signals between the
ITC-150 and ITC-100SL. All connections are contained within one cable.
14
2.2 Control Panel Overview
1.
Frame Store & AUX button
8.
Speed Selection
2.
Crosspoint buttons
9.
AUTO TAKE
3.
PC / Menu control
10.
FTB – Fade To Black
4.
Transition selection
11.
CUT
5.
Logos 1 & 2, Clock & Timer
12.
T-Bar – Manual Transitions
6.
PIP selection PST & PGM
13.
Preset Row (PST)
7.
DSK selection PST & PGM
14.
Program Row (PGM)
1
2
3
4
5 6 7
8
9
10
11
12
14
13
2.2.1 Video Switching
Program and Preset rows
The Program row of buttons is the active channel, this is the live output. The active channel
will appear as the Program Output (PGM). You can switch or CUT from one video source to
another directly on the Program row. You will see the multi view PGM output change as you
press different keys along this top row of buttons.
15
The Preset row is the cued channel, this channel will appear in the PST or Preview window.
1.
Vertical Wipe Left to Right.
4.
Horizontal Wipes from Centre to
Top and Bottom.
2.
Horizontal Wipe Top to
Bottom.
5.
Circle Wipe from Centre to
outside edges.
3.
Vertical Wipes from Centre to
Left and Right sides.
6.
Diamond Wipe from Centre to
outside edges.
INV
Invert the selected wipe so it
travels in the opposite
direction.
FIX / A+V
Switch the audio mixing option
between Audio Fixed and Audio-F-
Video (A+V).
MIX
Pressing this button selects a
basic A/B Dissolve for the next
transition.
FREEZE
Freeze the program source image or
return to live video of the selected
program source.
The Preset row selection decides which input will be transitioned next when using any of the
transition controls.
Note: The keys on the Program and Preset rows will be inactive while the T-Bar is active or
moving. Only when the T-Bar is fully up or fully down will the keys respond.
Background
The Background button assigns a background colour or SMPTE 75% bars for
use on the Program and Preset row.
2.2.2 Video Transitions
The HS-2850 features six user defined wipe
buttons, an A/B dissolve or MIX button, an INV
or Invert wipes button and a FREEZE button.
All wipes can have an optional colour border
applied. The wipe border width and colour are
chosen within the menu system.
Transitions can be performed manually using the T-Bar or automatically by using the SPEED
and AUTO TAKE buttons.
Transition Selection
16
Transition Effect Indication
The selected transition will be indicated
in the status area of the HDMI multiview output. When the INV button is
pressed, the six wipe icons change to
their opposite direction icon.
SPEED
There are three speed buttons which can be defined by the
user. By pressing a speed button the user is choosing the
rate of transition or time taken when using the AUTO TAKE
button.
AUTO TAKE
This performs an automated switch from the current
program source to the selected preset source. The selected
transition wipe or dissolve will also be used. The timing of
the transition is set by the chosen Speed button.
CUT
This performs a simple immediate switch from the current
main source to the selected sub source. The selected
transition wipe or dissolve is not used.
FTB
Fade To Black, this button fades the current video program
source to black. When pressed again it acts in reverse from
complete black to the currently selected program video
source.
T-Bar
This performs a manually controlled transition from the
current program source to the selected preset source. The
selected transition wipe or dissolve will be used. When the
T-Bar has travelled as far as it can go, the transition
between sources is complete. The T-Bar has indicators next
to it, which light when the transition is complete.
The T-Bar can be operated in one of two modes which is
chosen by a menu option, see the section on OSD MENU
options for more details.
Triggering the Transition
17
2.2.3 Logo and Clock
The HS-2850 has the ability to store six static logos and one
dynamic logo. The logo files are transferred to the HS-2850
from a Windows PC using the Ethernet connection and the
supplied SEConfig software. See Chapter 3 for more details on
using this software.
LOGO 1
The LOGO 1 and LOGO 2 buttons are used to display pre-
selected logos on the HS-2850 Preset and Program outputs.
When the button is active the selected logo is shown. These logos are selected from the
switcher’s memory and positioned using a menu option see the section on OSD MENU
options for details.
LOGO 2 or CLOCK
The user cannot display LOGO 2 and CLOCK at the same time. Instead use LOGO 1 and
CLOCK together or use LOGO 1 and LOGO 2 together.
The clock time can be synchronized with a computer or set manually using a menu option.
The colour and font used in the clock digits can be changed using the supplied SEConfig
software. See Chapter 3 for more details on using this software or see OSD MENU Options
onwards for the Clock menu options.
TIMER
In some mixing or switching applications it is useful to have a countdown timer. It could be
that the input is a pre-recorded video clip and you need to know when to be ready to switch
away from it.
This countdown timer function is only seen in the status area of the HDMI multi-view output
to the right of the normal Clock function. The timer can be selected for one input channel,
several channels or all channels.
When the TIMER button is active and the user switches to a selected input channel, the
countdown starts on the HDMI multi-view.
The value of the countdown, in minutes and seconds (MM:SS), is set by a menu option.
Whilst the countdown is in progress, T-Bar operation is ignored.
When the countdown reaches zero, the user can then switch or transition to another input
channel. If the countdown reaches zero the switcher will not automatically change to the
selected Preset source.
18
2.2.4 Picture-in-Picture and Downstream Key
PIP Preset and PIP Program
When looking at the top right corner of the HS-2850 Control
Panel / Keyboard there are four PIP keys. These are labelled
Program and Preset. The upper PIP1 and PIP2 keys relate to
activating Picture In Picture images on the Program outputs. The
lower PIP1 and PIP2 keys relate to activating Picture In Picture
images on the Multi-view or Preview outputs.
Assigning a video source input to a PIP
Using the lower PIP1 or PIP2 buttons you can assign a selected
video input to the chosen PIP video layer.
1. First press and hold down the required PIP button on the lower row. The Preset row
of input sources will light.
2. While still holding down the PIP button, press to select the required input from the
Preset row.
3. The input will flash to confirm it is selected.
This selection will also be confirmed on the HDMI Multi-view, with a PiP1 or PiP2 label
shown next to the selected input image.
The full PIP process is described in the section on Picture-In-Picture Function.
DSK Preset and DSK Program
When looking at the top right corner of the HS-2850 Control
Panel / Keyboard there are four DSK keys. These are labelled
Program and Preset. The upper DSK1 and DSK2 keys relate to
activating Down Stream Keying on the Program outputs. The
lower DSK1 and DSK2 keys relate to activating Down Stream
Keying on the Multi-view or Preview outputs.
Assigning an input to a DSK channel for keying
Using the lower DSK1 or DSK2 buttons you can assign a selected
video input to the chosen DSK video layer.
1. First press and hold down the required DSK button on the lower row. The Preset row
of input sources will light.
2. While still holding down the DSK button, press to select the required input from the
Preset row.
3. The input will flash to confirm it is selected.
This selection will also be confirmed on the HDMI Multi-view, with a T1 or T2 label shown
next to the selected input image.
The full DSK process is described in the section on DSK Settings.
19
2.2.5 Frame Store and Audio Control
FS – Frame Store Button
The HS-2850 has eight or twelve video channels, depending on the number of
inputs it has. Each of these channels has its own Frame Store, making a total of
eight or twelve Frame Stores. Each of these Frame Stores can hold one still
image. This still image can be called into the production by using the FS button located at
the top left corner of the HS-2850 Control Panel / Keyboard. The FS button allows the user
to toggle between the still image of the Frame Store or the live video input also connected
to that same video channel.
How to choose live video input or Frame Store
1. First press and hold down the FS button. The Preset row of input sources will light.
2. While still holding down the FS button, press the required input on the Preset row.
3. The input button will flash to confirm the Frame Store is selected.
This selection will also be confirmed on the HDMI Multi-view, with the selected channel
showing the live input or frame store image.
The content of each Frame Store is uploaded to the HS-2850 from a PC. The supplied
SEConfig software is used to do this. The file upload process is described in Chapter 3.
AUX Source Selection
The auxiliary output (AUX) allows you to fix the SDI output onto a particular
input source. The HS-2850 has four user defined SDI outputs, see Section 2.1.1
item 14. One or all of these outputs can be set up as an auxiliary (AUX) output
via a menu option. See OSD MENU Options onwards for details.
The AUX output source can be quickly selected in the following way.
1. First press and hold down the AUX button. The Input 1 and 2 buttons of the Program
row will light up red.
2. While still holding down the AUX button, press either the Input 1 button or the Input
2 button on the Program row.
3. The pressed input button (1 or 2) on the Program row will now flash red along with
one of the input buttons on the Preset row flashing green. The rest of the input
buttons on the Preset row will remain solid green.
4. The green flashing button on the Preset row indicates the selected source of the AUX
output. To change the source, simply press other input buttons.
When you see the selected input button flashing green, your AUX output source is now
assigned and you may release the AUX button to complete the AUX source selection.
2.2.6 Crosspoint
The CROSSPOINT function allows you to cross assign input channels to program/preset row
buttons. Follow the steps outlined below to assign video input channels to the
program/preset row buttons according to your preference.
20
XPT Video
Assign video source, and channel settings according to your preference.
Follow the steps outlined as follows:
1. First press and hold down the XPT VIDEO button. The Program row of input
sources will light.
2. While still holding down the XPT VIDEO button, press the required input on the
Program row. This selects the input source.
3. After pressing the required input on the program row, the Preset row of input
sources will light. While still holding down the XPT VIDEO button, press the
required input on the Preset row. This selects the channel button that the input
source is assigned to.
4. Release the XPT VIDEO button, the selected input button will flash to confirm the
selection.
Note: The XPT video function allows you to associate one video input channel to more than
one program/preset row buttons. For example, you can assign video input channel 1 to
multiple channels by pressing the respective channel buttons of the preset row at step 3 of
the above procedure.
The same procedure can be applied to audio channel sources as well. Follow the steps
described below to cross assign audio input channels to program/preset row buttons.
XPT Audio
Assign audio source, and channel settings according to your preference.
Follow the steps outlined as follows:
1. First press and hold down the XPT AUDIO button. The Program row of input
sources will light.
2. While still holding down the XPT AUDIO button, press the required input on
the Program row. This selects the input source.
3. After pressing the required input on the program row, the Preset row of input
sources will light. While still holding down the XPT AUDIO button, press the
required input on the Preset row. This selects the channel button that the input source
is assigned to.
4. Release the XPT AUDIO button, the selected input button will flash to confirm the
selection.
2.2.7 OSD MENU Options
When the ENTER button is pressed the Main Menu list is
displayed on the HDMI 1 Multi-view output.
This section covers the Menu options in the order that they
appear on the HS-2850 HDMI 1 Multi-view. These settings may
also appear in more detail elsewhere in this instruction manual.
Options may vary depending on the firmware version in use.
21
Once the chosen setting has been confirmed with the ENTER button it is stored within the
Version Number
Version Number xx.xx where xx.xx is the firmware version number.
Base Standard
1080i50Hz
Tick selection for ON or OFF
1080i60Hz
1080i59.94Hz
Note: When Output Standard & Format is set to the option HD SDI 1080p (25/29/30):
1. The Output will be automatically adjusted to 1080p25Hz if 1080i50Hz is selected for Base
Standard.
2. The Output will be automatically adjusted to 1080p29Hz if 1080i59.94Hz is selected for Base
Standard.
3. The Output will be automatically adjusted to 1080p30Hz if 1080i60Hz is selected for Base
Standard.
Audio Dynamic Range
Audio Dynamic Range
24
18
Audio Tract
EXTERNAL ANALOG AUDIO
Tick selection for ON or OFF
AUDIO PASS THROUGH
On Preview Video Adjustment
Brightness
72 to 184, default 128
Select the input that you want
to adjust in the PVW window.
This is a fine adjustment, the
change happens gradually as
the value is increased or
reduced.
Contrast
36 to 92, default 64
Saturation
36 to 92, default 64
Aperture
0 to 3
Y-C Delay
0 to 7
Set to Norminal
Reset to default values
Video Input Standard and Format
Inputs 1,2,3,5,6,7,9,
10&11
Can be a choice of:
HD SDI 1080i *
HD SDI 1080p (50/59/60Hz) *
HD SDI 1080p (25/29/30Hz) *
HD SDI 720p (50/59/60Hz) *
SD SDI 4:3
SD SDI 16:9
Inputs 4,8 &12
Can be a choice of
HD SDI 1080i *
HD SDI 1080p (50/59/60Hz) *
HD SDI 1080p (25/29/30Hz) *
HD SDI 720p (50/59/60Hz) *
SD SDI 4:3
SD SDI 16:9
HD HDMI 1080i
HD HDMI 1080p (50/59/60Hz)
HD HDMI 1080p (25/29/30Hz)
HD HDMI 720p(50/59/60Hz)
SD HDMI 4:3
SD HDMI 16:9
switchers non-volatile memory.
22
HDMI COLOR MODE: RGB / YUV 4:2:2 / YUV 4:4:4 / CG-200 MODE
*All HD inputs are natively 16:9 aspect ratio.
On Preview Audio Level and Delay
Level
Range +60 to -60
AUDIO DELAY
Range 0 to 16
Nominal
Resets value to 00
SDI De-Emb. Audio Group / Pair
Input 1 – 12
User choice of
GROUP: 1-4
PAIR: 1-2
HDMI De-Emb. Audio Group
Input 4 / 8 / 12
User choice of GROUP 1 / 2 / 3 / 4
Outputs SDI Re-Emb. Group
Output 1 / 2 / 3 /4
User choice of GROUP 1 / 2 / 3 / 4
Auto Audio Mixing Type
X-Type
Tick selection / X type = A/B cross fade
V-Type
Tick selection / V type = Fade out A then Fade in B
T-Bar Audio Mixing Type
Follow Auto (X or V) Type
Tick selection / use the option enabled in Auto Audio Mixing Type
By the End
Tick selection / clean cut or immediate audio switch
PIP Set Up
Position PIP 1
Horizontal Position (Left to Right)
000-097
Vertical Position (Lower to
Upper)
000-108
Size PIP 1
1 (Small) – 33 (Large)
Border PIP 1
Width
00-05
Color
1-8
1=White, 2=Yellow, 3=Cyan,
4=Green, 5=Magenta, 6=Red,
7=Blue, 8=Black
Position PIP 2
Horizontal Position (Left to Right)
000-097
Vertical Position (Lower to
Upper)
000-108
Size PIP 2
1 (Small) – 33 (Large)
Border PIP 2
Width
00-05
Color
1-8
1=White, 2=Yellow, 3=Cyan,
4=Green, 5=Magenta, 6=Red,
7=Blue, 8=Black
Logo Set Up
Logo 1
Select
01-08
Logo selection 1 to 7 are still
image
Logo 8 selection is dynamic
moving image
Horizontal Position (Left to Right)
000-110
Vertical Position (Lower to
Upper)
000-135
Logo 2
Select
01-08
Logo selection 1 to 7 are still
23
image
Logo 8 selection is dynamic
moving image
Horizontal Position (Left to Right)
000-110
Vertical Position (Lower to
Upper)
000-135
Speed Button Set Up
Speed 1
1-64 (Frames)
Speed 2
1-64 (Frames)
Speed 3
1-64 (Frames)
Wipe Button Set Up
Button 1-6
WIPE
1-8
Soft Edge
0-4
Color
1-8
1=White, 2=Yellow, 3=Cyan,
4=Green, 5=Magenta, 6=Red,
7=Blue, 8=Black
Outputs Mode and Standard
Output 1/2/3/4
Standard & Format
HD SDI
SD SDI 4:3
SD SDI 16:9
HD SDI 1080p (25/29/30)
Mode
Program
Program logo free
Program logo & DSK free
Preview
AUX 1
AUX 2
DSK Set Up
DSK 1 / 2
Fill & Key mode
Alpha channel
Luma Key mode
Luma Key level
0 (black) to 255 (white)
BG Color (1-8) and Color Bar (9)
1-9
Background Color Settings
1=White, 2=Yellow, 3=Cyan, 4=Green, 5=Magenta, 6=Red, 7=Blue,
8=Black, 9 = SMPTE 75% colour bars
T-Bar Mode
One Way Mode
= T-Bar operates transition in only one direction
Two Way Mode
= T-Bar operates transition in both directions
1kHz to Color Bar
1kHz to Color Bar
Tick selection for ON or OFF
Keys Brightness
1-4
Keyboard button brightness with user choice of 1 to 4
1 = Low, 4 = High
Multi-Screen Audio Indicators
Multi-Screen Audio
Indicators
Tick selection for ON or OFF
Reference
External
Reference
Tick selection for ON or OFF
Mode
HD: Analog 3 Level Signal
Tick selection for ON or OFF
24
SD: Composite Signal
Tick selection for ON or OFF
H-Timing
0-255
Factory Settings
Factory Settings
Tick selection for ON or OFF
Resets to factory default
Clock Settings
Horizontal Position (Left to
Right)
000-110
Vertical Position (Lower to
Upper)
000-124
SET Hours
0-23
SET Minutes
0-59
Clear Seconds
Tick selection for clearing second
Multi Screen Mode
This option sets HDMI outputs 1 and 2.
A: M1=PVW+PGM+3 IN; M2=9 IN
B: M1=PVW+PGM+12 IN; M2=PGM
C: M1=PVW+PGM+8 IN; M2=PGM
D: M1=PVW+PGM+12 IN; M2=M1
E: M1=PVW+PGM+8 IN; M2=M1
GPI Settings
Input Select
00-12
Chosen input number
Time Delay
In frames between 1 to 75
Mode
Level Mode
Tick selection for ON or OFF
Pulse Mode
Tick selection for ON or OFF
Countdown Timer Settings
Input 1-12
Count Down Enable
Each input can be selected
for Count Down ON or OFF.
Down Counter Value
If Count Down is ON then the
Down Counter value is set in
minutes and seconds
(MM:SS) - Max.= 1 Hour or
60:00, Default = 15 Seconds
or 00:15
Multi-Screen Audio Source
Preview
Tick selection of Program or Preview audio on the HDMI outputs
Program
Control Interface
Ethernet
Tick selection for ON or OFF
RS422
2.2.8 PC Control – SE Remote Control Software
It is possible to control the HS-2850 with a Windows 7 computer using an Ethernet
connection. The SE Remote software supplied with the switcher needs to be installed on the
computer first. The HS-2850 then needs to be placed into PC Control mode. To do this press
the PC Control button on the HS-2850 Control Panel. Once launched, the Remote software
displays an image of the HS-2850’s keyboard as shown below. Any active functions or
selections will be shown with a red button or key. These buttons or keys can be clicked with
a mouse or alternatively you could use a touch screen monitor.
25
Before launching the SE Remote software, please see Chapter 3 Switcher Configuration
Utility for network setup information.
NOTE: It is not possible to run both the SEConfig and SE Remote software applications at the
same time.
SET Function
After the network connection between the PC and the HS-2850 is successfully configured,
you can then launch the SE Remote software on the PC. Locate SET function button which is
located just above the T-Bar. When clicked, a new window will open as shown left below.
This Settings window is used to match the software to the IP address of the connected HS2850 switcher.
Enter the switcher’s IP address and then click the “Check” button to determine the switcher
model number which is then selected from the “Model” pull-down menu. Once configured,
click the OK button to shut down to “Settings” window and the SE Remote software should
be successfully connected to the HS-2850 as shown in the diagram below.
26
Loading...