Page 1
Features
• High output voltage and wide bandwidth; optimal for
use in fH(horizontal deflection frequency) = 100 kHz
class monitors.
(f = 130 MHz –3 dB at V
OUT
= 40 Vp-p)
• SIP molded 15-pin package houses three amplifier
channels.
Package Dimensions
unit: mm
2127A
Wideband Output Module (Video Pack)
Ordering number : EN5548A
83097HA (OT)/03096HA (OT) No. 5548-1/4
[VPS13]
SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110 JAPAN
CRT Display Video Output Amplifier,
High-Voltage/Wideband Amplifier
VPS13
Parameter Symbol Conditions Ratings Unit
Maximum supply voltage
V
CC
max 90 V
V
BB
max 15 V
Allowable power dissipation Pd max With an ideal heat sink at Tc = 25°C 30 W
Maximum junction temperature Tj max 150 °C
Maximum case temperature Tc max 100 °C
Storage temperature Tstg –20 to +110 °C
Specifications
Absolute Maximum Ratings at Ta = 25°C
Parameter Symbol Conditions Ratings Unit
Recommended supply voltage
V
CC
80 V
V
BB
10 V
Operating Conditions at Ta = 25°C
Parameter Symbol Conditions
Ratings
Unit
min typ max
Frequency band (–3 dB) f
c
V
CC
= 80 V, VBB= 10 V, CL= 10 pF
130 MHz
V
IN
(DC) = 3.2 V, V
OUT
(p-p) = 40 V
Impulse response
t
r
V
CC
= 80 V, VBB= 10 V, CL= 10 pF 3.5 ns
t
f
V
IN
(DC) = 3.2 V, V
OUT
(p-p) = 40 V 2.9 ns
Voltage gain VG (DC) 13 15 17 double
I
CC
(1)
V
CC
= 80 V, VBB= 10 V, VIN(DC) = 2.9 V,
47 mA
Current drain
f = 10 MHz clock, CL= 10 pF, V
OUT
(p-p) = 40 V
ICC(2)
V
CC
= 80 V, VBB= 10 V, VIN(DC) = 2.9 V,
85 mA
f = 130 MHz clock, CL= 10 pF, V
OUT
(p-p) = 40 V
Electrical Characteristics at Ta = 25°C (for a single channel)
Page 2
Internal Equivalent Circuit
Test Circuit (for a single channel)
No. 5548-2/4
VPS13
Page 3
Thermal Design
Since the VPS13 includes three channels as shown in the circuit diagram on page 2, we first consider a single channel.
The chip temperature of each transistor under actual operating conditions is determined using the following formula.
Tj = (Tri) = θj-c (Tri) × Pc (Tri) + ∆Tc + Ta (°C).......................(1)
θ
j-c (Tri) : Thermal resistance of an individual transistor
Pc(Tri) : Collector loss for an individual transistor
∆Tc : Case temperature rise
Ta : Ambient temperature
The θj-c (Tri) for each chip is: θj-c (Tr1) = 35°C/W
θ
j-c (Tr2) to (Tr4) = 30°C/W.......................................................(2)
Although the loss for each transistor in a video pack varies with frequency and is not uniform, if we assume the
maximum operating frequency, f = 130 MHz (clock), then the chip with the largest loss will be transistor 3 (Tr3) of the
emitter-follower stage. From the Pd-f (clock) figure we see that loss will be 22% of the total loss for a single channel:
Pc (emitter-follower stage)
(f = 130 MHz)
= Pd (1ch)
(f = 130 MHz)
× 0.22 [W] (3)
Here, we must select a heat sink with a capacity θh such that the Tj of these transistors does not exceed 150°C. Equation
(4) below gives the relationship between θh and ∆Tc.
∆Tc = Pd (Total) ×θh..................................................................(4)
The required θh is calculated using this equation and equation (1).
No. 5548-3/4
VPS13
Page 4
No. 5548-4/4
VPS13
VPS13 Thermal Design Example
Conditions: Using an fH= 100 kHz class monitor, fV= 130 MHz (clock)
VCC= 80 V, VBB= 10 V, V
OUT
= 40 Vp-p (CL= 10 pF)
Here we consider the case where this class of monitor is operated up to Ta = 60°C at a maximum clock frequency of
f = 130 MHz.
As mentioned previously, the chip with the largest loss is transistor 3 (Tr3) of the emitter-follower stage. Determining
that value gives:
Pc (emitter-follower stage) = 6.8 × 0.22 ≈ 1.5 [W] .....................(5)
Now, determine ∆Tj by substituting the value for θj-c in equation (5).
∆Tj = 1.5 × 30 = 45 [°C]
Here, ∆Tj < 50°C, and we need only consider cases where Tc < 100 °C. Therefore, we must design a θh for the heat sink
such that the Tc < 100°C condition holds when three channels are operating at maximum levels, i.e., Pd(TOTAL) =
Pd(one channel) × 3.
∆Tc will be 100 – 60 = 40 °C, and therefore:
θ
h = ∆Tc ÷ Pd (TOTAL) = 40 ÷ (6.8 × 3) = 2.0, i.e. θh = 2.0 °C/W
In actual practice, the ambient temperature and operating conditions will allow a heat sink smaller than that indicated by
this calculation to be used. Therefore, design optimization taking the actual conditions and the above data into account is
also required.
This catalog provides information as of August, 1997. Specifications and information herein are subject to
change without notice.
■ No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace
equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of
which may directly or indirectly cause injury, death or property loss.
■ Anyone purchasing any products described or contained herein for an above-mentioned use shall:
➀
Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and
distributors and all their officers and employees, jointly and severally, against any and all claims and litigation and all
damages, cost and expenses associated with such use:
➁
Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on
SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees
jointly or severally.
■ Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for
volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied
regarding its use or any infringements of intellectual property rights or other rights of third parties.
VCC(V) VBB(V) V
OUT
(V) VO(center)
80 10 40 45
Loading...