Page 1
INTEGRATED CIRCUITS
74F805, 74F1805
Hex 2-input NOR drivers
Product specification
IC15 Data Handbook
1990 Sep 14
Page 2
Philips Semiconductors Product specification
74F805/74F1805Hex 2-input NOR drivers
FEA TURES
•High capacitive drive capability
•Choice of configuration
Corner V
Center V
and GND – 74F805
CC
and GND – 74F1805
CC
•Typical propagation delay of 2.3ns
TYPICAL
PROPAGATION
TYPE
DELA Y
74F805 2.3ns 10mA
74F1805 2.3ns 10mA
ORDERING INFORMATION
ORDER CODE
DESCRIPTION COMMERCIAL RANGE
= 5V ±10%,
V
CC
T
= 0°C to +70°C
amb
20–pin plastic DIP N74F805N, N74F1805N SOT146-1
20–pin plastic SOL N74F805D, N74F1805D SOT163-1
INPUT AND OUTPUT LOADING
AND FAN OUT TABLE
PINS DESCRIPTION 74F
Dna – Dnb Data inputs 1.0/0.033 20µA/20µA
Q0 – Q5 Data outputs 2400/80 48mA/48mA
NOTE: One (1.0) FAST unit load is defined as: 20µA in the high
state and 0.6mA in the low state.
TYPICAL SUPPL Y
CURRENT
(U.L.)
HIGH/
LOW
( TOTAL)
PKG DWG #
LOAD VALUE
HIGH/LOW
PIN CONFIGURATION
D0a
1
D0b
2
Q
0
3
D1a
4
D1b
5
1
Q
6
D2a
7
D2b
8
2
Q
9
GND
10 11
LOGIC SYMBOL
1245781213
D0a D0bD1a D2a D2b D3aD3bD1b
Q0 Q1 Q2 Q3
36 911
V
= Pin 20
CC
= Pin 10
GND
74F805
74F805
20 V
CC
19
D5b
18
D5a
17
Q
5
16
D4b
15
D4a
14
4
Q
13
D3b
12
D3a
3
Q
SF00456
15 16 18 19
D4aD4bD5aD5b
Q4 Q5
14 17
SF00457
IEC/IEEE SYMBOL
74F805
1
2
4
5
7
8
12
13
15
16
18
19
September 14, 1990 853-0037 00417
2
1
3
6
9
11
14
17
SF00458
Page 3
Philips Semiconductors Product specification
74F805/74F1805Hex 2-input NOR drivers
PIN CONFIGURATION
1
D4b
2
Q
5
3
D5a
4
D5b
5
V
CC
6
D0a
7
D0b
8
Q
0
9
D1a
10 11
D1b
LOGIC SYMBOL
6 7 9 1012131718
D0aD0bD1a D2aD2b D3a D3bD1b
Q0 Q1 Q2 Q3
8111416
V
= Pin 5
CC
= Pin 15
GND
74F1805
74F1805
20
D4a
19
Q
4
18
D3b
17
D3a
16
3
Q
15
GND
14
Q
2
13
D2b
12
D2a
Q
1
SF00459
20 1 3 4
D4aD4bD5a D5b
Q4 Q5
2
19
SF00460
LOGIC DIAGRAM
74F805
1
D0a
D0b
D1a
D1b
D2a
D2b
D3a
D3b
D4a
D4b
D5a
D5b
2
4
5
7
8
12
13
15
16
18
19
V
GND = Pin 10
CC
= Pin 20
3
6
9
11
14
17
FUNCTION TABLE
INPUTS OUTPUT
Dna Dnb Qn
H X L
X H L
L L H
Notes to function table
H = High voltage level
L = Low voltage level
X = Don’t care
74F1805
6
D0a
D0b
D1a
D1b
D2a
D2b
D3a
D3b
D4a
D4b
D5a
D5b
7
9
10
12
13
17
18
20
1
3
4
V
= Pin 5
CC
= Pin 15
GND
O
Q
1
Q
Q
2
Q
3
4
Q
Q
5
8
Q
11
Q
14
Q
16
Q
19
Q
2
Q
SF00462
O
1
2
3
4
5
IEC/IEEE SYMBOL
6
7
9
10
12
13
17
18
20
1
3
4
September 14, 1990
74F1805
1
8
11
14
16
19
2
SF00461
3
Page 4
Philips Semiconductors Product specification
SYMBOL
PARAMETER
UNIT
74F805/74F1805Hex 2-input NOR drivers
ABSOLUTE MAXIMUM RATINGS
(Operation beyond the limit set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the
operating free air temperature range.)
SYMBOL
V
V
I
IN
V
I
OUT
T
T
CC
IN
OUT
amb
stg
Supply voltage –0.5 to +7.0 V
Input voltage –0.5 to +7.0 V
Input current –30 to +5 mA
Voltage applied to output in high output state –0.5 to V
Current applied to output in low output state 96 mA
Operating free air temperature range 0 to +70
Storage temperature range –65 to +150
RECOMMENDED OPERATING CONDITIONS
V
V
V
I
I
OH
I
OL
T
amb
Supply voltage 4.5 5.0 5.5 V
CC
High–level input voltage 2.0 V
IH
Low–level input voltage 0.8 V
IL
Input clamp current –18 mA
Ik
High–level output current –48 mA
Low–level output current 48 mA
Operating free air temperature range 0 +70 °C
PARAMETER RATING UNIT
CC
V
°C
°C
LIMITS
MIN NOM MAX
DC ELECTRICAL CHARACTERISTICS
(Over recommended operating free-air temperature range unless otherwise noted.)
SYMBOL
V
OH
High-level output voltage VCC = MIN, VIL = MAX
PARAMETER TEST CONDITIONS
VIH = MIN, IOH = MAX
V
OL
V
IK
I
I
I
IH
I
IL
I
O
I
CC
NOTES:
1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type.
2. All typical values are at VCC = 5V, T
3. The output conditions have been chosen to produce a current that closely approximates one half of the true short–circuit output current, I
Low-level output voltage VCC = MIN, VIL = MAX
VIH = MIN, I
Input clamp voltage VCC = MIN, II = I
Ol
= MAX
IK
Input current at maximum input voltage VCC = MAX, VI = 7.0V 100 µA
High–level input current VCC = MAX, VI = 2.7V 20 µA
Low–level input current VCC = MAX, VI = 0.5V -20 µA
Output current
Supply current (total) I
3
= 25°C.
amb
VCC = MAX -60 -150 mA
CCHVCC
I
CCL
= MAX VIN = GND 3.0 5.0 mA
1
±10%V
±10%V
±5%V
±5%V
MIN TYP
CC
CC
CC
CC
LIMITS UNIT
2
MAX
2.0 V
2.0 V
0.38 0.55 V
0.38 0.55 V
-0.73 -1.2 V
VIN = 4.5V 17 25 mA
OS
.
September 14, 1990
4
Page 5
Philips Semiconductors Product specification
74F805/74F1805Hex 2-input NOR drivers
AC ELECTRICAL CHARACTERISTICS
LIMITS
T
= +25°C T
amb
SYMBOL PARAMETER TEST VCC = +5.0V
CONDITION CL = 50pF,
= 500Ω
R
L
MIN TYP MAX MIN MAX
t
PLH
t
PHL
t
sk(o)
Propagation delay
Dna, Dnb to Qn
Output skew
1,2
Waveform 1
1.0
1.0
2.0
2.5
Waveform 2 1.5 1.5 ns
NOTES:
1. [t
actual – tPM actual] for any output compared to any other output where N and M are either LH or HL.
PN
2. Skew times are valid only under same test conditions (temperature, V
, loading, etc.,).
CC
AC WAVEFORMS
4.0
4.5
= 0°C to +70°C
amb
VCC = +5.0V ± 10%
CL = 50pF,
= 500Ω
R
L
1.0
1.0
4.0
4.5
UNIT
ns
Dna, Dnb
Qn
V
M
t
PHL
V
M
V
M
Waveform 1. Propagation delay for inverting output
NOTE: For all waveforms, VM = 1.5V.
TEST CIRCUIT AND WAVEFORMS
V
CC
V
PULSE
GENERATOR
IN
R
T
Test Circuit for Totem-Pole Outputs
D.U.T.
V
OUT
C
t
PLH
L
Qn
V
M
SF00005
Qn
V
M
t
sk(0)
V
M
SF00455
Waveform 2. Output skew
t
NEGATIVE
PULSE
R
L
POSITIVE
PULSE
90%
10%
V
M
10%
t
THL (tf
t
TLH (tr
90%
V
M
w
V
M
10%
)
)
t
w
t
TLH (tr
t
THL (tf
)
)
90%
V
M
90%
10%
AMP (V)
0V
AMP (V)
0V
DEFINITIONS:
R
= Load resistor;
L
see AC ELECTRICAL CHARACTERISTICS for value.
= Load capacitance includes jig and probe capacitance;
C
L
see AC ELECTRICAL CHARACTERISTICS for value.
R
= Termination resistance should be equal to Z
T
pulse generators.
September 14, 1990
OUT
of
family
74F
5
Input Pulse Definition
INPUT PULSE REQUIREMENTS
V
amplitude
3.0V
M
1.5V
rep. rate
1MHz 500ns
t
w
t
TLHtTHL
2.5ns 2.5ns
SF00006
Page 6
Philips Semiconductors Product specification
74F805, 74F1805Hex 2-input NOR drivers
DIP20: plastic dual in-line package; 20 leads (300 mil) SOT146-1
1990 Sep 14
6
Page 7
Philips Semiconductors Product specification
74F805, 74F1805Hex 2-input NOR drivers
SO20: plastic small outline package; 20 leads; body width 7.5 mm SOT163-1
1990 Sep 14
7
Page 8
Philips Semiconductors Product specification
74F805, 74F1805Hex 2-input NOR drivers
Data sheet status
Data sheet
status
Objective
specification
Preliminary
specification
Product
specification
Product
status
Development
Qualification
Production
Definition
This data sheet contains the design target or goal specifications for product development.
Specification may change in any manner without notice.
This data sheet contains preliminary data, and supplementary data will be published at a later date.
Philips Semiconductors reserves the right to make chages at any time without notice in order to
improve design and supply the best possible product.
This data sheet contains final specifications. Philips Semiconductors reserves the right to make
changes at any time without notice in order to improve design and supply the best possible product.
[1]
[1] Please consult the most recently issued datasheet before initiating or completing a design.
Definitions
Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or
at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended
periods may affect device reliability.
Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips
Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or
modification.
Disclaimers
Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can
reasonably be expected to result in personal injury . Philips Semiconductors customers using or selling these products for use in such applications
do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application.
Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard
cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Sunnyvale, California 94088–3409
Telephone 800-234-7381
Copyright Philips Electronics North America Corporation 1999
All rights reserved. Printed in U.S.A.
print code Date of release: 04-99
Document order number: 9397-750-05718
1990 Sep 14
8
Loading...