Page 1
74ALS00A
Quad 2-Input NAND gate
Product specification 1991 Feb 08
INTEGRATED CIRCUITS
IC05 Data Handbook
Page 2
Philips Semiconductors Product specification
74ALS00AQuad 2-input NAND gate
2
1991 Feb 08 853–0038 01670
TYPE
TYPICAL
PROPAGATION DELAY
TYPICAL
SUPPLY CURRENT
(TOTAL)
74ALS00A 4.0ns 1.0mA
ORDERING INFORMATION
ORDER CODE
DESCRIPTION COMMERCIAL RANGE
V
CC
= 5V ±10%,
T
amb
= 0°C to +70°C
DRAWING
NUMBER
14-pin plastic DIP 74ALS00AN SOT27-1
14-pin plastic SO 74ALS00AD SOT108-1
14-pin plastic SSOP
Type II
74ALS00ADB SOT337-1
PIN CONFIGURATION
14
13
12
11
10
9
87
6
5
4
3
2
11A
1B
1Y
2A
2B
2Y
GND 3Y
3A
3B
4Y
4A
4B
V
CC
SC00001
INPUT AND OUTPUT LOADING AND FAN-OUT TABLE
PINS DESCRIPTION
74ALS (U.L.)
HIGH/LOW
LOAD VALUE
HIGH/LOW
nA, nB Data inputs 1.0/1.0 20µA/0.1mA
nY Data output 20/80 0.4mA/8mA
NOTE: One (1.0) ALS unit load is defined as: 20µA in the High state and 0.1mA in the Low state.
LOGIC SYMBOL
VCC = Pin 14
GND = Pin 7
12459101213
1A 1B 2A 2B 3A 3B 4A 4B
1Y 2Y 3Y 4Y
36811
SC00002
IEC/IEEE SYMBOL
1
2
4
5
9
10
12
13
&
3
6
8
11
SF00004
LOGIC DIAGRAM
VCC = Pin 14
GND = Pin 7
1A
1B
2A
2B
3A
3B
4A
4B
1Y
2Y
3Y
4Y
3
6
8
11
1
2
4
5
9
10
12
13
SC00003
FUNCTION TABLE
INPUTS OUTPUT
nA nB nY
H H L
L X H
X L H
H = High voltage level
L = Low voltage level
X = Don’t care
Page 3
Philips Semiconductors Product specification
74ALS00AQuad 2-input NAND gate
1991 Feb 08
3
ABSOLUTE MAXIMUM RATINGS
(Operation beyond the limit set forth in this table may impair the useful life of the device.
Unless otherwise noted these limits are over the operating free-air temperature range.)
SYMBOL
PARAMETER RATING UNIT
V
CC
Supply voltage –0.5 to +7.0 V
V
IN
Input voltage –0.5 to +7.0 V
I
IN
Input current –30 to +5 mA
V
OUT
Voltage applied to output in High output state –0.5 to V
CC
V
I
OUT
Current applied to output in Low output state 16 mA
T
amb
Operating free air temperature range 0 to +70 °C
T
stg
Storage temperature range –65 to +150 °C
RECOMMENDED OPERATING CONDITIONS
SYMBOL PARAMETER LIMITS UNIT
MIN NOM MAX
V
CC
Supply voltage 4.5 5.0 5.5 V
V
IH
High-level input voltage 2.0 V
V
IL
Low-level input voltage 0.8 V
I
Ik
Input clamp current –18 mA
I
OH
High-level output current –0.4 mA
I
OL
Low-level output current 8 mA
T
amb
Operating free-air temperature range 0 +70 °C
DC ELECTRICAL CHARACTERISTICS
(Over recommended operating free-air temperature range unless otherwise noted.)
1
LIMITS
SYMBOL
PARAMETER
TEST CONDITIONS
1
MIN TYP2MAX
UNIT
V
OH
High-level output voltage VCC±10%, VIL = MAX, VIH = MIN, IOH = –0.4mA V
CC
– 2 V
p
VCC = MIN, VIL = MAX,
I
OL
= 4mA 0.25 0.40 V
VOLLow-level output voltage
CC
,
IL
,
VIH = MIN
I
OL
= 8mA 0.35 0.50 V
V
IK
Input clamp voltage VCC = MIN, II = I
IK
-0.73 -1.5 V
I
I
Input current at maximum input voltage VCC = MAX, VI = 7.0V 0.1 mA
I
IH
High-level input current VCC = MAX, VI = 2.7V 20 µA
I
IL
Low-level input current VCC = MAX, VI = 0.5V -0.1 mA
I
O
Output current
3
VCC = MAX, VO = 2.25V -30 -112 mA
pp
I
CCH
VI = GND 0.5 0.85 mA
ICCSupply current (total)
I
CCL
V
CC
=
MAX
VI = 4.5V 1.5 3.0 mA
NOTES:
1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type.
2. All typical values are at V
CC
= 5V, T
amb
= 25°C.
3. The output conditions have been chosen to produce a current that closely approximate one half of the true short-circuit output current, I
OS
.
Page 4
Philips Semiconductors Product specification
74ALS00AQuad 2-input NAND gate
1991 Feb 08
4
AC ELECTRICAL CHARACTERISTICS
LIMITS
SYMBOL PARAMETER TEST CONDITION
T
amb
= 0°C to +70°C
V
CC
= +5.0V ± 10%
C
L
= 50pF, RL = 500Ω
UNIT
MIN MAX
t
PLH
t
PHL
Propagation delay
nA, nB to nY
Waveform 1
2.0
2.0
11.0
8.0
ns
AC WAVEFORMS
For all waveforms, VM = 1.3V .
V
M
V
M
V
M
V
M
t
PLH
t
PHL
nA, nB
nY
SC00004
Waveform 1. Propagation Delay for Data to Output
TEST CIRCUIT AND WAVEFORMS
t
w
90%
V
M
10%
90%
V
M
10%
90%
V
M
10%
90%
V
M
10%
NEGATIVE
PULSE
POSITIVE
PULSE
t
w
AMP (V)
0.3V
0.3V
t
THL (tf
f
)
INPUT PULSE REQUIREMENTS
Rep.Rate
t
w
t
TLHtTHL
1MHz
500ns
2.0ns 2.0ns
Input Pulse Definition
V
CC
Family
74ALS
D.U.T.
PULSE
GENERATOR
R
L
C
L
R
T
V
IN
V
OUT
Test Circuit for Totem-pole Outputs
DEFINITIONS:
R
L
= Load resistor;
see AC electrical characteristics for value.
C
L
= Load capacitance includes jig and probe capacitance;
see AC electrical characteristics for value.
R
T
= Termination resistance should be equal to Z
OUT
of
pulse generators.
t
THL (tf
)
t
TLH (tr
)
t
TLH (tr
)
AMP (V)
Amplitude
3.5V
1.3V
V
M
SC00005
Page 5
Philips Semiconductors Product specification
74ALS00AQuad 2-input NAND gate
1991 Feb 08
5
DIP14: plastic dual in-line package; 14 leads (300 mil) SOT27-1
Page 6
Philips Semiconductors Product specification
74ALS00AQuad 2-input NAND gate
1991 Feb 08
6
SO14: plastic small outline package; 14 leads; body width 3.9 mm SOT108-1
Page 7
Philips Semiconductors Product specification
74ALS00AQuad 2-input NAND gate
1991 Feb 08
7
SSOP14: plastic shrink small outline package; 14 leads; body width 5.3 mm SOT337-1
Page 8
Philips Semiconductors Product specification
74ALS00AQuad 2-input NAND gate
1991 Feb 08
8
Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products,
including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips
Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright,
or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask
work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes
only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing
or modification.
LIFE SUPPORT APPLICA TIONS
Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices,
or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected
to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips
Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully
indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale.
This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips
Semiconductors reserves the right to make changes at any time without notice in order to improve design
and supply the best possible product.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Sunnyvale, California 94088–3409
Telephone 800-234-7381
DEFINITIONS
Data Sheet Identification Product Status Definition
Objective Specification
Preliminary Specification
Product Specification
Formative or in Design
Preproduction Product
Full Production
This data sheet contains the design target or goal specifications for product development. Specifications
may change in any manner without notice.
This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes
at any time without notice, in order to improve design and supply the best possible product.
Copyright Philips Electronics North America Corporation 1997
All rights reserved. Printed in U.S.A.
print code Date of release: 05-96
Document order number:
Loading...