Datasheet MMBF2201NT3, MMBF2201NT1 Datasheet (Motorola)

Download

Page 1

Motorola Small–Signal Transistors, FETs and Diodes Device Data

 $ !

 

 "     # !""# !"

Part of the GreenLine Portfolio of devices with energy–con-

serving traits.

These miniature surface mount MOSFETs utilize Motorola’s

High Cell Density, HDTMOS process. Low r

DS(on)

assures minimal power loss and conserves energy, making this device ideal for use in small power management circuitry. Typical applications are dc–dc converters, power management in portable and battery–powered products such as computers, printers, PCMCIA cards, cellular and cordless telephones.

• Low r

DS(on)

Provides Higher Efficiency and Extends Battery

Life

• Miniature SC–70/SOT–323 Surface Mount Package Saves

Board Space

MAXIMUM RATINGS

(TJ = 25°C unless otherwise noted)

Rating Symbol Value Unit

Drain–to–Source Voltage V

DSS

20 Vdc

Gate–to–Source Voltage — Continuous V

± 20 Vdc

Drain Current — Continuous @ TA = 25°C

Drain Current — Continuous @ TA = 70°C Drain Current — Pulsed Drain Current (tp ≤ 10 µs)

300 240 750

mAdc

Total Power Dissipation @ TA = 25°C

(1)

Derate above 25°C

150

1.2

mW/°C

Operating and Storage Temperature Range TJ, T

stg

– 55 to 150 °C

Thermal Resistance — Junction–to–Ambient R

θJA

833 °C/W

Maximum Lead Temperature for Soldering Purposes, for 10 seconds T

260 °C

DEVICE MARKING

(1) Mounted on G10/FR4 glass epoxy board using minimum recommended footprint.

ORDERING INFORMATION

Device Reel Size Tape Width Quantity

MMBF2201NT1 7″ 8 mm embossed tape 3000 MMBF2201NT3 13″ 8 mm embossed tape 10,000

GreenLine is a trademark of Motorola, Inc. HDTMOS is a trademark of Motorola, Inc. TMOS is a registered trademark of Motorola, Inc. Thermal Clad is a registered trademark of the Berquist Company.

Preferred devices are Motorola recommended choices for future use and best overall value.

Order this document

by MMBF2201NT1/D



SEMICONDUCTOR TECHNICAL DATA

CASE 419–02, Style 8

SC–70/SOT–323



N–CHANNEL

ENHANCEMENT–MODE

TMOS MOSFET

DS(on)

= 1.0 OHM

Motorola Preferred Device

 Motorola, Inc. 1998



3 DRAIN

1 GATE

2 SOURCE

REV 2

Page 2

MMBF2201NT1

Motorola Small–Signal Transistors, FETs and Diodes Device Data

ELECTRICAL CHARACTERISTICS

(TA = 25°C unless otherwise noted)

Characteristic Symbol Min Typ Max Unit

OFF CHARACTERISTICS

Drain–to–Source Breakdown Voltage

(VGS = 0 Vdc, ID = 10 µA)

(BR)DSS

20 — — Vdc

Zero Gate Voltage Drain Current

(VDS = 16 Vdc, VGS = 0 Vdc) (VDS = 16 Vdc, VGS = 0 Vdc, TJ = 125°C)

DSS

— —

1.0 10

µAdc

Gate–Body Leakage Current (VGS = ± 20 Vdc, VDS = 0) I

GSS

— — ±100 nAdc

ON CHARACTERISTICS

(1)

Gate Threshold Voltage

(VDS = VGS, ID = 250 µAdc)

GS(th)

1.0 1.7 2.4 Vdc

Static Drain–to–Source On–Resistance

(VGS = 10 Vdc, ID = 300 mAdc) (VGS = 4.5 Vdc, ID = 100 mAdc)

DS(on)

— —

0.75

1.0

1.4

Ohms

Forward Transconductance (VDS = 10 Vdc, ID = 200 mAdc) g

— 450 — mMhos

DYNAMIC CHARACTERISTICS

Input Capacitance (VDS = 5.0 V) C

iss

— 45 — pF

Output Capacitance (VDS = 5.0 V) C

oss

— 25 —

Transfer Capacitance (VDG = 5.0 V) C

rss

— 5.0 —

SWITCHING CHARACTERISTICS

(2)

Turn–On Delay Time

d(on)

— 2.5 —

Rise Time

(VDD = 15 Vdc, ID = 300 mAdc,

— 2.5 —

Turn–Off Delay Time

(

RL = 50 Ω)

d(off)

— 15 —

Fall Time t

— 0.8 —

Gate Charge (See Figure 5) Q

— 1400 — pC

SOURCE–DRAIN DIODE CHARACTERISTICS

Continuous Current I

— — 0.3 A

Pulsed Current I

— — 0.75

Forward Voltage

(2)

— 0.85 — V

(1) Pulse Test: Pulse Width ≤ 300 µs, Duty Cycle ≤ 2%. (2) Switching characteristics are independent of operating junction temperature.

TYPICAL CHARACTERISTICS

Figure 1. Typical Drain Characteristics

VDS, DRAIN–SOURCE VOLTAGE (VOLTS)

Figure 2. On Resistance versus Temperature

TEMPERATURE (°C)

, DRAIN CURRENT (AMPS)

, ON RESISTANCE (OHMS)

0.5

0.6

0.7

0.8

0.9

1.0

4087910

0.6

0.8

1.0

1.2

1.4

1.6

–60

123 5

0.1

0.2

0.3

0.4

0.2

–40 –20 0 20 40 60 80 100 120 140 160

VGS = 4 V

VGS = 3.5 V

VGS = 2.5 V

VGS = 3 V

VGS = 4.5 V

VGS = 10 V

ID = 100 mA

ID = 300 mA

Page 3

MMBF2201NT1

Motorola Small–Signal Transistors, FETs and Diodes Device Data

TYPICAL CHARACTERISTICS

C, CAPACITANCE (pF)

Figure 3. On Resistance versus Gate–Source

Voltage

GATE–SOURCE VOLTAGE (VOLTS)

Figure 4. On Resistance versus Drain Current

ID, DRAIN CURRENT (AMPS)

, ON RESISTANCE (OHMS)

Figure 5. Source–Drain Forward Voltage

VSD, SOURCE–DRAIN FORWARD VOLTAGE (VOLTS)

Figure 6. Capacitance Variation

VDS, DRAIN–SOURCE VOLTAGE (VOLTS)

Figure 7. Transfer Characteristics

VGS, GATE–SOURCE VOLTAGE (VOLTS)

7096810

0.2

0.4

0.6

0.8

1.0

1.2

0.10 0.5

0.01

0.1

1.0

0.001

0.10

40 8 12 16 20

241 3 5 0.2 0.3 0.4 0.80.6 0.7

, ON RESISTANCE (OHMS)

, SOURCE CURRENT (AMPS)

0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 2 6 10 14 18

0.2

0.4

0.6

0.8

0.9

1.0

0.50 2.51.0 1.5 2.0 4.03.0 3.5

, DRAIN CURRENT (AMPS)

4.5

0.3

0.5

0.7

0.1

ID = 300 mA

VGS = 4.5 V

VGS = 10 V

VGS = 0 V

F = 1 mHz

iss

oss

rss

–55

150

Page 4

MMBF2201NT1

Motorola Small–Signal Transistors, FETs and Diodes Device Data

INFORMATION FOR USING THE SC–70/SOT–323 SURFACE MOUNT PACKAGE

MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS

Surface mount board layout is a critical portion of the total design. The footprint for the semiconductor packages must be the correct size to insure proper solder connection

interface between the board and the package. With the correct pad geometry, the packages will self align when subjected to a solder reflow process.

inches

0.035

0.9

0.075

0.7

1.9

0.028

0.65

0.025

0.65

0.025

SC–70/SOT–323

SC–70/SOT–323 POWER DISSIPATION

The power dissipation of the SC –70 / SOT– 323 is a function of the drain pad size. This can vary from the minimum pad size for soldering to a pad size given for maximum power dissipation. Power dissipation for a surface mount device is determined by T

J(max)

, the maximum rated

junction temperature of the die, R

θJA

, the thermal resistance from the device junction to ambient, and the operating temperature, TA. Using the values provided on the data sheet for the SC–70 package, PD can be calculated as follows:

PD =

J(max)

– T

θJA

The values for the equation are found in the maximum ratings table on the data sheet. Substituting these values into the equation for an ambient temperature TA of 25°C, one can

calculate the power dissipation of the device which in this case is 150 milliwatts.

PD =

150°C – 25°C

833°C/W

= 150 milliwatts

The 833°C/W for the SC–70/SOT–323 package assumes the use of the recommended footprint on a glass epoxy printed circuit board to achieve a power dissipation of 150 milliwatts. There are other alternatives to achieving higher power dissipation from the SC –70/ SOT– 323 package. Another alternative would be to use a ceramic substrate or an aluminum core board such as Thermal Clad. Using a board material such as Thermal Clad, an aluminum core board, the power dissipation can be doubled using the same footprint.

SOLDERING PRECAUTIONS

The melting temperature of solder is higher than the rated temperature of the device. When the entire device is heated to a high temperature, failure to complete soldering within a short time could result in device failure. Therefore, the following items should always be observed in order to minimize the thermal stress to which the devices are subjected.

• Always preheat the device.

• The delta temperature between the preheat and

soldering should be 100°C or less.*

• When preheating and soldering, the temperature of the

leads and the case must not exceed the maximum temperature ratings as shown on the data sheet. When using infrared heating with the reflow soldering method, the difference should be a maximum of 10°C.

• The soldering temperature and time should not exceed

260°C for more than 10 seconds.

• When shifting from preheating to soldering, the

maximum temperature gradient should be 5°C or less.

• After soldering has been completed, the device should

be allowed to cool naturally for at least three minutes. Gradual cooling should be used as the use of forced cooling will increase the temperature gradient and result in latent failure due to mechanical stress.

• Mechanical stress or shock should not be applied during

cooling

* Soldering a device without preheating can cause excessive thermal shock and stress which can result in damage to the device.

Page 5

MMBF2201NT1

Motorola Small–Signal Transistors, FETs and Diodes Device Data

P ACKAGE DIMENSIONS

CASE 419–02

SC–70/SOT–323

ISSUE J

NOTES:

1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.

2. CONTROLLING DIMENSION: INCH.

DIM MIN MAX MIN MAX

MILLIMETERSINCHES

A 0.071 0.087 1.80 2.20 B 0.045 0.053 1.15 1.35 C 0.035 0.049 0.90 1.25 D 0.012 0.016 0.30 0.40 G 0.047 0.055 1.20 1.40 H 0.000 0.004 0.00 0.10 J 0.004 0.010 0.10 0.25 K 0.017 REF 0.425 REF L 0.026 BSC 0.650 BSC N 0.028 REF 0.700 REF R 0.031 0.039 0.80 1.00 S 0.079 0.087 2.00 2.20 V 0.012 0.016 0.30 0.40

0.05 (0.002)

STYLE 8:

PIN 1. GATE

2. SOURCE

3. DRAIN

Page 6

MMBF2201NT1

Motorola Small–Signal Transistors, FETs and Diodes Device Data

Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty , representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “T ypical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.

Mfax is a trademark of Motorola, Inc.

How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 4–32–1,

P.O. Box 5405, Denver, Colorado 80217. 303–675–2140 or 1–800–441–2447 Nishi–Gotanda, Shinagawa–ku, Tokyo 141, Japan. 81–3–5487–8488 Mfax: RMFAX0@email.sps.mot.com – TOUCHTONE 602–244–6609 ASIA/P ACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,

– US & Canada ONLY 1–800–774–1848 51 Ting Kok Road, Ta i Po, N.T., Hong Kong. 852–26629298

INTERNET: http://motorola.com/sps

MMBF2201NT1/D

◊