Page 1
LM1558/LM1458
Dual Operational Amplifier
General Description
The LM1558 and the LM1458 are general purpose dual operational amplifiers.The two amplifiers sharea commonbias
network and power supply leads. Otherwise, their operation
is completely independent.
The LM1458 is identical to the LM1558 except that the
LM1458 has its specifications guaranteed over the temperature range from 0˚C to +70˚C instead of −55˚C to +125˚C.
Features
n No frequency compensation required
n Short-circuit protection
n Wide common-mode and differential voltage ranges
n Low-power consumption
n 8-lead can and 8-lead mini DIP
n No latch up when input common mode range is
exceeded
Schematic and Connection Diagrams
DS007886-1
Numbers in parentheses are pin numbers for amplifier B.
April 1998
LM1558/LM1458 Dual Operational Amplifier
© 1999 National Semiconductor Corporation DS007886 www.national.com
Page 2
Schematic and Connection Diagrams (Continued)
Metal Can Package
DS007886-2
Top View
Order Number LM1558H,
LM1558H/883 or LM1458H
See NS Package Number H08C
Dual-In-Line Package
DS007886-3
Top View
Order Number LM1558J, LM1558J/883, LM1458J,
LM1458M or LM1458N
See NS Package Number J08A, M08A or N08E
www.national.com 2
Page 3
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the NationalSemiconductor Sales Office/
Distributors for availability and specifications.
(Note 5)
Supply Voltage
LM1558
±
22V
LM1458
±
18V
Power Dissipation (Note 2)
LM1558H/LM1458H 500 mW
LM1458N 400 mW
Differential Input Voltage
±
30V
Input Voltage (Note 3)
±
15V
Output Short-Circuit Duration Continuous
Operating Temperature Range
LM1558
LM1458
−55˚C to +125˚C
0˚C to +70˚C
Storage Temperature Range −65˚C to +150˚C
Lead Temperature (Soldering, 10 sec.) 260˚C
Soldering Information
Dual-In-Line Package
Soldering (10 seconds) 260˚C
Small Outline Package
Vapor Phase (60 seconds) 215˚C
Infrared (15 seconds) 220˚C
See AN-450 “Surface Mounting Methods and Their Effect
on Product Reliability” for other methods of soldering
surface mount devices.
ESD tolerance (Note 6) 300V
Electrical Characteristics (Note 4)
Parameter Conditions LM1558 LM1458 Units
Min Typ Max Min Typ Max
Input Offset Voltage T
A
=
25˚C, R
S
≤ 10 kΩ 1.0 5.0 1.0 6.0 mV
Input Offset Current T
A
=
25˚C 80 200 80 200 nA
Input Bias Current T
A
=
25˚C 200 500 200 500 nA
Input Resistance T
A
=
25˚C 0.3 1.0 0.3 1.0 MΩ
Supply Current Both T
A
=
25˚C, V
S
=
±
15V 3.0 5.0 3.0 5.6 mA
Amplifiers
Large Signal Voltage Gain T
A
=
25˚C, V
S
=
±
15V 50 160 20 160 V/mV
V
OUT
=
±
10V, RL≥ 2kΩ
Input Offset Voltage R
S
≤ 10 kΩ 6.0 7.5 mV
Input Offset Current 500 300 nA
Input Bias Current 1.5 0.8 µA
Large Signal Voltage Gain V
S
=
±
15V, V
OUT
=
±
10V 25 15 V/mV
R
L
≥ kΩ
Output Voltage Swing V
S
=
±
15V, R
L
=
10 kΩ
±
12
±
14
±
12
±
14 V
R
L
=
2kΩ
±
10
±
13
±
10
±
13 V
Input Voltage Range V
S
=
±
15V
±
12
±
12 V
Common Mode R
S
≤ 10 kΩ 70 90 70 90 dB
Rejection Ratio
Supply Voltage R
S
≤ 10 kΩ 77 96 77 96 dB
Rejection Ratio
Note 1: “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits.
Note 2: The maximum junction temperature of the LM1558 is 150˚C, while thatof the LM1458 is 100˚C. For operating at elevated temperatures, devices inthe H08
package must be derated basedon a thermal resistance of150˚C/W, junction toambient or 20˚C/W,junction to case. For theDIP the device must be derated based
on a thermal resistance of 187˚C/W, junction to ambient.
Note 3: For supply voltages less than
±
15V, the absolute maximum input voltage is equal to the supply voltage.
Note 4: These specifications apply for V
S
=
±
15V and −55˚C ≤ TA≤ 125˚C, unless otherwise specified. With the LM1458, however, all specifications are limited to
0˚C ≤ T
A
≤ 70˚C and V
S
=
±
15V.
Note 5: Refer to RETS 1558V for LM1558J and LM1558H military specifications.
Note 6: Human body model, 1.5 kΩ in series with 100 pF.
www.national.com3
Page 4
Physical Dimensions inches (millimeters) unless otherwise noted
Metal Can Package (H)
Order Number LM1558H, LM1558H/883 or LM1458H
NS Package Number H08C
Small Outline Package (M)
Order Number LM1458M
NS Package Number M08A
www.national.com 4
Page 5
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
Small Outline Package (M)
Order Number LM1458M
NS Package Number M08A
Molded Dual-In-Line Package (N)
Order Number LM1458N
NS Package Number N08E
www.national.com5
Page 6
Notes
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL
SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: support@nsc.com
National Semiconductor
Europe
Fax: +49 (0) 1 80-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 1 80-530 85 85
English Tel: +49 (0) 1 80-532 78 32
Français Tel: +49 (0) 1 80-532 93 58
Italiano Tel: +49 (0) 1 80-534 16 80
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: sea.support@nsc.com
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
www.national.com
LM1558/LM1458 Dual Operational Amplifier
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
Loading...