Page 1
July 1994
HA-5114/883
Quad, Low Noise, High Performance
Uncompensated Operational Amplifier
Features
• This Circuit is Processed in Accordance to MIL-STD883 and is Fully Conformant Under the Provisions of
Paragraph 1.2.1.
• Low Input Noise Voltage Density at 1kHz. . . 6nV/√
4.3nV/√
Hz(Max)
Hz (Typ)
• High Slew Rate. . . . . . . . . . . . . . . . . . . . . . 12V/µs (Min)
20V/µs (Typ)
• Wide Gain Bandwidth Product (A
≥ 10). . . 40MHz (Typ)
VCL
• High Open Loop Gain (Full Temp) . . . . . 100kV/V (Min)
250kV/V (Typ)
• High CMRR, PSRR (Full Temp). . . . . . . . . . . 86dB (Min)
100dB (Typ)
• Low Offset Voltage Drift . . . . . . . . . . . . . . 3µV/
o
C (Typ)
• No Crossover Distortion
• Standard Quad Pinout
Applications
• High Quality Audio Preamplifiers
• High Q Active Filters
• Low Noise Function Generators
• Low Distortion Oscillators
• Low Noise Comparators
Description
Low noise and high performance are key words describing
the quad, uncompensated HA-5114/883. This general purpose amplifier offers an array of dynamic specifications
including 12V/µs slew rate (min), and 40MHz gain-bandwidth-product for A
ing parameters is a very low noise specification of 6nV/√
≥ 10. Complementing these outstand-
VCL
Hz
at 1kHz (max).
Fabricated using the Intersil standard high frequency D.I.
process, these operational amplifiers also offer excellent
input specifications such as 2.5mV (max) offset voltage and
75nA (max) offset current. Complementing these specifications are 100dB (min) open loop gain and 55dB channel
separation (min). Economically, HA-5114/883 also consumes a very modest amount of power (225mW/ package),
while also saving board space and cost.
This impressive combination of features make this amplifier
ideally suited for designs ranging from audio amplifiers and
active filters to the most demanding signal conditioning and
instrumentation circuits.
Ordering Information
PART
NUMBER
HA1-5114/883 -55oC to +125oC 14 Lead CerDIP
HA4-5114/883 -55oC to +125oC 20 Lead Ceramic LCC
TEMPERATURE
RANGE PACKAGE
Pinouts
HA-5114/883
(CERDIP)
TOP VIEW
OUT 1
1
-IN1
2
--
+
3
+IN1
V+
4
+IN2
5
+
-IN2
OUT 2
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207
-
6
7
4
1
3
2
| Copyright © Intersil Corporation 1999
OUT 4
14
-IN4
13
+
+IN4
12
V-
11
+IN3
10
+
-
-IN3
9
8
OUT 3
3-124
+IN1
NC
V+
NC
+IN2
HA-5114/883
(CLCC)
TOP VIEW
-IN1
OUT 1NCOUT 4
3212019
4
+
--
1
5
6
2
7
+
8
9101112
-IN2
OUT 2NCOUT 3
-IN4
+IN4
18
+
4
17
NC
16
VNC
15
3
+
-14
+IN3
13
-IN3
File Number
File Number 3712
511015-883
Page 2
Specifications HA-5114/883
Absolute Maximum Ratings Thermal Information
Voltage between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . . 40V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V
Voltage at Either Input Terminal . . . . . . . . . . . . . . . . . . . . . . V+ to V-
Peak Output Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Indefinite
(One Amplifier Shorted to Ground)
Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC
Storage Temperature Range . . . . . . . . . . . . . . . . . -65oC to +150oC
ESD Rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <2000V
Lead Temperature (Soldering 10s). . . . . . . . . . . . . . . . . . . . +300oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Operating Conditions
Operating Temperature Range. . . . . . . . . . . . . . . . -55oC to +125oC
Operating Supply Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . ±5V to ±15V
TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS
Device Tested at: V
PARAMETERS SYMBOL CONDITIONS
Input Offset Voltage V
Input Bias Current +I
Input Offset Current I
Common Mode Range +CMR V+ = +3V, V- = -27V 1 +25oC +12 - V
Large Signal Voltage
Gain
Common Mode
Rejection Ratio
SUPPLY
= ±15V, R
IO
B
SOURCE
= 100Ω, R
LOAD
= 500kΩ, V
VCM = 0V 1 +25oC -2.5 2.5 mV
VCM = 0V, +RS = 10kΩ,
-RS = 100Ω
-I
VCM = 0V, +RS = 100Ω,
B
-RS = 10kΩ
IO
VCM = 0V,
+RS = 10kΩ,
-RS = 10kΩ
-CMR V+ = +27V, V- = -3V 1 +25oC - -12 V
+A
VOL
V
= 0V and +10V,
OUT
RL = 2kΩ
-A
VOL
V
= 0V and -10V,
OUT
RL = 2kΩ
+CMRR ∆VCM = +5V,
V+ = +10V, V- = -20V,
V
= -5V
OUT
-CMRR ∆VCM = -5V,
V+ = +20V, V- = -10V,
V
= +5V
OUT
Thermal Resistance θ
JA
CerDIP Package . . . . . . . . . . . . . . . . . . . 75oC/W 20oC/W
Ceramic LCC Package . . . . . . . . . . . . . . 65oC/W 15oC/W
Package Power Dissipation Limit at +75oC
CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.33W
Ceramic LCC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.54W
Package Power Dissipation Derating Factor Above +75oC
CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13.3mW/oC
Ceramic LCC Package . . . . . . . . . . . . . . . . . . . . . . . .15.4mW/oC
V
≤ 1/2 (V+ - V-)
INCM
RL≥ 2kΩ
= 0V, Unless Otherwise Specified.
OUT
GROUP A
SUBGROUPS TEMPERATURE
LIMITS
UNITSMIN MAX
2, 3 +125oC, -55oC -3.0 3.0 mV
1 +25oC -200 200 nA
2, 3 +125oC, -55oC -325 325 nA
1 +25oC -200 200 nA
2, 3 +125oC, -55oC -325 325 nA
1 +25oC -75 75 nA
2, 3 +125oC, -55oC -125 125 nA
2, 3 +125oC, -55oC +12 - V
2, 3 +125oC, -55oC - -12 V
4 +25oC 100 - kV/V
5, 6 +125oC, -55oC 100 - kV/V
4 +25oC 100 - kV/V
5, 6 +125oC, -55oC 100 - kV/V
1 +25oC86-dB
2, 3 +125oC, -55oC86 - dB
1 +25oC86-dB
2, 3 +125oC, -55oC86 - dB
θ
JC
3-125
Spec Number 511015-883
Page 3
Specifications HA-5114/883
TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued)
Device Tested at: V
PARAMETERS SYMBOL CONDITIONS
Output Voltage Swing +V
Output Current +I
Quiescent Power Supply
Current
Power Supply
Rejection Ratio
SUPPLY
= ±15V, R
OUT1
-V
OUT1
+V
OUT2
-V
OUT2
OUT
-I
OUT
+I
CC
-I
CC
+PSRR ∆V
-PSRR ∆V
= 100Ω, R
SOURCE
RL = 2kΩ 1 +25oC10-V
RL = 2kΩ 1 +25oC - -10 V
RL = 10kΩ 1 +25oC12-V
RL = 10kΩ 1 +25oC - -12 V
V
= -5V 1 +25oC10-mA
OUT
V
= +5V 1 +25oC - -10 mA
OUT
V
= 0V, I
OUT
V
= 0V, I
OUT
SUP
V+ = +10V, V- = -15V
V+ = +20V, V- = -15V
SUP
V+ = +15V, V- = -10V
V+ = +15V, V- = -20V
= 10V,
= 10V,
LOAD
= 500kΩ, V
= 0V, Unless Otherwise Specified.
OUT
GROUP A
LIMITS
SUBGROUPS TEMPERATURE
2, 3 +125oC, -55oC10 - V
2, 3 +125oC, -55oC - -10 V
2, 3 +125oC, -55oC12 - V
2, 3 +125oC, -55oC - -12 V
2, 3 +125oC, -55oC10 - mA
2, 3 +125oC, -55oC - -10 mA
= 0mA 1 +25oC - 6.5 mA
OUT
2, 3 +125oC, -55oC - 7.5 mA
= 0mA 1 +25oC -6.5 - mA
OUT
2, 3 +125oC, -55oC -7.5 - mA
1 +25oC86-dB
2, 3 +125oC, -55oC86 - dB
1 +25oC86-dB
2, 3 +125oC, -55oC86 - dB
UNITSMIN MAX
TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS
Table 2 Intentionally Left Blank. See AC Parameters in Table 3
TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS
Device Characterized at: V
SUPPLY
= ±15V, R
LOAD
= 2kΩ, C
LOAD
= 50pF, A
= 10V/V, Unless Otherwise Specified.
VCL
PARAMETERS SYMBOL CONDITIONS NOTES TEMPERATURE
Differential Input
R
VCM = 0V 1 +25oC 250 - kΩ
IN
Resistance
Input Noise Voltage E
N
RS = 20Ω,
1 +25oC-6nV/√Hz
fO = 1000Hz
Input Noise Current I
N
RS = 2MΩ,
1 +25oC-3pA/√Hz
fO = 1000Hz
Gain Bandwidth Product GBWP VO= 200mV,
1 +25oC 34 - MHz
fO= 30kHz
VO= 200mV,
1 +25oC 40 - MHz
fO= 1MHz
3-126
LIMITS
Spec Number
UNITSMIN MAX
511015-883
Page 4
Specifications HA-5114/883
TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued)
Device Characterized at: V
PARAMETERS SYMBOL CONDITIONS NOTES TEMPERATURE
Slew Rate +SR V
Full Power Bandwidth FPBW V
Minimum Closed Loop
Stable Gain
Rise and Fall Time t
Overshoot +OS V
Output Resistance R
Quiescent Power
Consumption
Channel Separation CS RS = 1kΩ,
NOTES:
1. Parameters listed in Table 3 are controlled via design or process parameters and are not directly tested at final production. These parameters are lab characterized upon initial design release, or upon design changes. These parameters are guaranteed by characterization
based upon data from multiple production runs which reflect lot to lot and within lot variation.
2. Full Power Bandwidth guarantee based on Slew Rate measurement using FPBW = Slew Rate/(2πV
3. Quiescent Power Consumption based upon Quiescent Supply Current test maximum. (No load on outputs.).
4. Measured between 10% and 90% points.
SUPPLY
= ±15V, R
LOAD
= 2kΩ, C
LOAD
= 50pF, A
= 10V/V, Unless Otherwise Specified.
VCL
LIMITS
= -5V to +5V 1 +25oC12-V/µs
OUT
-SR V
= +5V to -5V 1 +25oC12-V/µs
OUT
= 10V 1, 2 +25oC 191 - kHz
PEAK
CLSG RL = 2kΩ, CL = 50pF 1 -55oC to +125oC 10 - V/V
V
R
t
F
-OS V
OUT
PC V
= 0V to +200mV 1, 4 +25oC - 100 ns
OUT
V
= 0V to -200mV 1, 4 +25oC - 100 ns
OUT
= 0V to +200mV 1 +25oC - 40 %
OUT
= 0V to -200mV 1 +25oC - 40 %
OUT
Open Loop 1 +25oC - 270 Ω
OUT
= 0V, I
= 0mA 1, 3 -55oC to +125oC - 225 mW
OUT
1 +25oC55-dB
A
= 100V/V,
VCL
VIN = 100mV
PEAK
at
10kHz Referred to
Input
).
PEAK
UNITSMIN MAX
TABLE 4. ELECTRICAL TEST REQUIREMENTS
MIL-STD-883 TEST REQUIREMENTS SUBGROUPS (SEE TABLE 1)
Interim Electrical Parameters (Pre Burn-In) 1
Final Electrical Test Parameters 1 (Note 1), 2, 3, 4, 5, 6
Group A Test Requirements 1, 2, 3, 4, 5, 6
Groups C and D Endpoints 1
NOTE:
1. PDA applies to Subgroup 1 only.
3-127
Spec Number
511015-883
Page 5
Die Characteristics
DIE DIMENSIONS:
99.6 x 95.3 x 19 mils ± 1 mils
2530 x 2420 x 483µm ± 25.4µm
METALLIZATION:
Type: Al, 1% Cu
Thickness: 16k
GLASSIVATION:
Type: Nitride (Si3N4) over Silox (SiO2, 5% Phos.)
Silox Thickness: 12kÅ ± 2kÅ
Nitride Thickness: 3.5kÅ ± 1.5kÅ
Å ± 2kÅ
HA-5114/883
WORST CASE CURRENT DENSITY:
1.43 x 10
5
A/cm2at 10mA
SUBSTRATE POTENTIAL (Powered Up):
Unbiased
TRANSISTOR COUNT: 175
PROCESS: Bipolar Dielectric Isolation
Metallization Mask Layout
+IN2 V+ +IN1
-IN2
OUT2
HA-5114/883
-IN1
OUT1
OUT3
-IN3
+IN4V-+IN3
OUT4
-IN4
All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification.
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate
and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which
may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see web site http://www.intersil.com
Spec Number 511015-883
3-128
Loading...