Datasheet FBR56ND12 Specification

Non-promotional not for new designs

FTR-K1 SERIES

COMPACT HIGH POWER RELAY

1 POLE - 30A (for automotive applications)

FBR56 Series

n FEATURES

l High power contact capacity

(carrying current: 40 A/10 minutes, 30 A/1 hour)

l High heat resistance and extended operating voltage
l Contact gap 0.4mm
l RoHS compliant

Please see page 7 for more information

n PARTNUMBER INFORMATION

FBR56 N D12 - W1 - **
[Example] (a) (b) (c) (d) (e)

(a) Relay type FBR56 : FBR56 Series (for 12V battery, contact gap 0.4mm)

(b) Enclosure Nil : Flux proof
N : Plastic sealed type

(c) Coil rated voltage D12 : 6.....12 VDC

Coil rating table at page 3

(d) Contact material W1 : Silver-tin oxide indium

Y : Silver-tin oxide

(e) Special type To be assigned custom specication

Actual marking does not carry the type name: "FBR"
E

.g.: Ordering code: FBR56ND12-W1 Actual marking: 56ND12-W1

1

FTR-K1 SERIES

FBR56 SERIES

n SPECIFICATION

Item FBR56
Contact Data Conguration 1 form C

Material

Voltage drop (resistance) Max.100 mV at 1A, 12VDC

Contact rating

Max. carrying current

Max. inrush current 70A (reference)
Max. switching voltage 16VDC (reference)
Max. switching current 40A (reference)
Min. switching load * 6 VDC, 1A

Life Mechanical Min. 10 x 10

Electrical

Coil Data Operating temperature range -40 °C to +85 °C (no frost)

Storage temperature range -40 °C to +100 °C (no frost)

Timing Data Operate (at nominal voltage) Max. 10 ms

Release (at nominal voltage) Max. 5 ms

Other Vibration resistance 10 to 55Hz double amplitude 1.5mm

Misoperation 100m/s²

Shock

Endurance 1,000m/s²

Weight Approximately 9.4 g

Silver-tin oxide indium (-W1 type)
Silver-tin oxide (-Y type)

14VDC, 30A (locked motor load)
14 VDC, Inrush 27A, break 4A (motor free load)

40A/10 minutes, 30A/1 hour
(25 °C, 100% rated coil voltage)

6

operations

3

Min. 100 x 10
Min. 1 x 106 operations (motor free load)

operations (locked motor load)

* Minimum switching loads mentioned above are reference values. Please perform the conrmation test with actual

load before production since reference values may vary according to switching frequencies, environmental conditions
and expected reliability levels.

2

n COIL RATING

FTR-K1 SERIES

FBR56 SERIES

Coil

Code

D06 6 42 3.6 (at 20 °C) 0.5 (at 20 °C)

D09 9 95 5.4 (at 20 °C) 0.7 (at 20 °C)

D12 12 170 7.3 (at 20 °C) 1 (at 20 °C)

Note: All values in the table are valid for 20°C and zero contact current, unless otherwise stated.

* Specied operate values are valid for pulse wave voltage.

Rated Coil

Voltage (VDC)

Coil Resistance +/- 10% (Ohm)

Must Operate Voltage

(VDC) *

4.5 (at 85 °C) 0.6 (at 85 °C)

6.8 (at 85 °C) 0.8 (at 85 °C)

9.2 (at 85 °C) 1.2 (at 85 °C)

Must Release Voltage

(VDC) *

n PRINCIPAL APPLICATIONS

Recommended

3

model (Example)

100 FBR56N ( ) - Y

300 FBR56N ( ) - W1

100 FBR56N ( ) - Y

For 12V

battery

Application Normal load current Life x 10

Power windows 20A tot 30A (switching at motor locking) 100 FBR56N ( ) -Y

Automatic door lock 18A to 30A / 4 to 5 door

(switching at motor locking)

Intermittent wipers Inrush 15A to 30A

Break 2A to 8A (motor free)

Tilt-lock wheel Inrush 15A

Break 2.5A (motor free)

Sunroof 20A to 30A (switching at motor locking) 100 FBR56N ( ) - Y

Others Car audio system, etc. - FBR56N ( ) - Y

n CHARACTERISTIC DATA

3

FTR-K1 SERIES

FBR56 SERIES

4

Life test (example)

(1) Motor lock

Test item Test circuit Current wave form

20A, 14VDC
Motor lock
200,000 operations minimun
Contact material:
Silver tin oxide indium

30A, 14VDC
Motor lock
100,000 operations minimum
Contact material:
Silver tin oxide indium

FTR-K1 SERIES

FBR56 SERIES

(2) Motor free

Test item Test circuit Current wave form

Inrush 27A, Idle 4A
14VDC
Motor free
100,000 operations minimum
Contact material:
Silver tin oxide indium

5

n DIMENSIONS

FTR-K1 SERIES

FBR56 SERIES

l Dimensions

l Schematics

(BOTTOM VIEW)

l PC board mounting
hole layout

(BOTTOM VIEW)

l Tube carrier

Unit: mm

6

FTR-K1 SERIES

FBR56 SERIES

RoHS Compliance and Lead Free Information

1. General Information

l All relays produced by Fujitsu Components are compliant with RoHS directive 2011/65/EU including

amendments.

l Cadmium as used in electrical contacts is exempted from the RoHS directives.

As per Annex III of directive 2011/65/EU.

l All relays are lead-free. Please refer to Lead-Free Status Info for older date codes at:

http://www.fujitsu.com/downloads/MICRO/fcai/relays/lead-free-letter.pdf

l Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified.

This material has been verified to be compatible with PbSn assembly process.

2. Recommended Lead Free Solder Condition

Flow Solder condition:

Pre-heating: maximum 120˚C

Soldering: dip within 5 sec at

255˚C ± 5˚C solder bath

Relay must be cooled by air immediately
after soldering

Solder by Soldering Iron:

Soldering Iron 30-60W

Temperature: maximum 350-360˚C

Duration: maximum 3 sec.

We highly recommend that you conrm your actual solder conditions

3. Moisture Sensitivity

l Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated.

4. Tin Whiskers

l Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length

whisker was found by our in house test.

7

Fujitsu Components International Headquarter Ofces

FTR-K1 SERIES

FBR56 SERIES

Japan

Fujitsu Component Limited
Gotanda-Chuo Building
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141, Japan
Tel: [phone]
Fax: [phone]
Email: [e-mail]
Web: www.fcl.fujitsu.com

North and South America

Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [e-mail]
Web: http://us.fujitsu.com/components

Europe

Fujitsu Components Europe B.V.
Diamantlaan 25
2132 WV Hoofddorp
Netherlands
Tel: [phone]
Fax: [phone]
Email: [e-mail]
Web: emea.fujitsu.com/components/

Asia Pacic

Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
#01-01 Citilink Warehouse Complex
Singapore 118529
Tel: [phone]
Fax: [phone]
Email: [e-mail]
Web: http://www.fujitsu.com/sg/services/micro/components/

©2013 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners.

The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general
information purposes.
The use of the contents, data and information provided in this datasheet is at the users’ own risk.
Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive,
complete and up to date.

Fujitsu Components Europe B.V. and afliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its

employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related
graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof.

Nor do Fujitsu Components Europe B.V. and afliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability
for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or tness for particular use,

with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness,
usefulness, availability and completeness thereof. Rev. July 03, 2013

8