Datasheet EM91810B, EM91810A Datasheet (ELAN)

GENERAL DESCRIPTION

The EM91810A/B are Tone/Pulse switchable dialer which are fabricated in CMOS technology with wide
operating voltage for both tone and pulse mode, and consumes very low memory retention current in ON-HOOK
state. EM91810A/B also provide SDO (serial data output) function to drive LCD driver (EM32100, EM32116,
EM32117) and voice synthesizer.

FEATURES

• Tone/pulse switchable dialer.

•One 32-digit last number redial memory.

•Pulse to tone (P→T) is provided for PBX operation.

•Flash key is available.

•Minimum tone duration is 98ms or 83ms.

•Minimum intertone pause is 98ms or 83ms.

•Uses 3.579545 MHz crystal or ceramic resonator.

•Many options can be selected.
Mode (10 PPS ; 20 PPS ; Tone)
M/B ratio (40 : 60 ; 33 : 66)
Pause time (3.6s)

•Flash function (RESET)
P→T pause time (3.6s)
Flash time (600ms; 300ms; 100ms; or 80ms).

•Mixed dialing.

•Handfree function is provided for speaker phone application.

•Power on reset circuit is provided.

•Package in DIP18 or DIP20.

•SDO function that is supported to drive LCD driver (EM32100) and voice synthesizer to indicate dialing
number.

•Key tone function is provided.

EM91810A/B

EM91810A/B

TONE/PULSE SWITCHABLE DIALER WITH LCD INTERFACE

TONE/PULES SWITCHABLE DIALER WITH LCD INTERFACE

PIN ASSIGNMENTS

EM91810A

C2

1

C3

2

C4

3

C1

4

OSCI

OSCO

XMUTE

V

SDO

5
6
7

SS

8
9

* This specification are subject to be changed without notice.

18
17
16
15
14
13
12
11
10

R3
R2
R1
R4
TONE
PO
HKS
V

DD

KT

C2
C3
C4
C1

OSCI

OSCO

XMUTE

V

HFI

SDO

EM91810B

1
2
3
4
5
6
7
8

SS

9

10

20
19
18
17
16
15
14
13
12
11

R3
R2
R1
R4
TONE
PO
HKS

DD

V
HFO
KT

10.1.1997

1

KEYBOARD ASSIGNMENT

EM91810A/B

TONE/PULSE SWITCHABLE DIALER WITH LCD INTERFACE

C1 C2 C3 C4

R1 1 2 3 P→T
R2 456F
R3 789P
R4 *or*/T 0 # RD

FUNCTIONAL BLOCK DIAGRAM

COL1

COL2

COL3

COL4

OSCI
OSCO

ROW1
ROW2

ROW3
ROW4

OSC.

COLUMN

INTERFACE CKT.

DIVIDER

ROW

INTERFACE CKT.

1). P→T : In pulse mode, execute P→T function.

2). F : Flash key.

3). RD : Redial key.

4). P : Pause key.

5). */T : In pulse mode, execte P→T function

KT

SDO

XMUTE

OUTPUT INTERFACE CKT.

LNB MEMORY

KERNEL CONTROL CKT.

INPUT INTERFACE CKT.

HFO

In tone mode, execte "*" key.

DD

V

PULSE

GENERATOR

DECODER &

DATA LATCH

ROW/COLUMN

PROGRAMMING

COUNTER

D/A CONVERTER

PO

TONE

DIALING SIGNAL OPTION :

a]:Flash time:

Row3 Row4

NR

R

R

flash time(ms)

NR

RNR

NR

R

600
300

100

80

c]:Tone function:

Col1

NR

R

Tone Duration

98 ms
83 ms

inter-Tone

Pause

98 ms
83 ms

* This specification are subject to be changed without notice.

b).

Row1 Row2

R NR TONE
R R TONE

NR
NR
UR
UR R PULSE 10PPS 33:66

d]:Key type select

Col2

NR

HKS

NR PULSE

R PULSE

NR PULSE

*or*/T
select

R */T

HFI

MODE PULSE RATE M/B

20PPS 40:60
20PPS 33:66
10PPS 40:60

Note: NR:no resistance.

*

R : A resistance connect to Vss

UR: A resistance connect to V

SS

V

(820KΩ typically)

DD

10.1.1997

2

TONE/PULES SWITCHABLE DIALER WITH LCD INTERFACE

n

PIN DESCRIPTION

Symbol Function

EM91810A/B

C1
C2
C3
C4

R1
R2
R3
R4

Provides keyboard scanning .

a. Keyboard scanning:

HKS pin is LOW, the column group stays in "HIGH" stays and row group stays in "LOW" state.
The key pad is compatible with the standard dual contact matrix keyboard (as Figure 1b.), the
inexpensive single contact keyboard (as Figure 1a.), and electronic input (as Figure 1c.).
When HKS is “low”, a valid key entry is defined by related Row & Column connection or by
electronic input; (as show in Figure 1c).
Activation of two or more keys will result in no response, except for single key.
To avoid keyboard bouncing error, this chip provides built-in debounce circuit. (The debounce
time = 20 ms.)

Row Column

Figure 1a : Single contact form keyboard configuration

Row

Column

Figure 1b : Dual contact form keyboard configuration

V

Row

Colum

V

V

DD

SS

DD
V

SS

Figure 1c : Electronic signal input keyboard configuration

OSCI
OSCO

Oscillator input & Oscillator output pins.
The 3.579545 MHz oscillator is formed by a built-in inverter inside of this chip and by connecting a

3.579545 MHz crystal or a ceramic resonator across the OSCI and OSCO pins. (built-in feedback
resistor and capacitor)
When HKS is “low”, a valid key-in may turn on this oscillator and generates a 3.579545 MHz clock.

XMUTE

Mute output pins.
NMOS open drain output structure.
The output is in “low” state during dialing sequence (both Pulse and Tone mode) otherwise this pin
is “high-impedance” .
Long (continue) Mute.

V

SS

V

DD

HKS

Negative power supply pin.
Positive power supply pin.
Hook switch input pin.
When the handset is in ON-HOOK state, this pin must be pulled “high” in order to disable the dialing
operation and decrease the power consumption.
When in OFF-HOOK state, the HKS pin must be pulled “low” state for all function operation.

PO

Pulse output signal pin.
NMOS open drain output structure.
The output is “low” during pulse dialing and Flash operation, otherwise this output is “floating”.

* This specification are subject to be changed without notice.

10.1.1997

3

TONE/PULSE SWITCHABLE DIALER WITH LCD INTERFACE

Symbol Function

EM91810A/B

TONE

HFI

HFO

SDO

KT

Dual Tone Multi-frequency output pin.
In TONE mode, when a entry of digit key (include * , # key), this pin will sent out a corresponding
DTMF signal.
The TONE pin provides minimum tone duration (t
key-in. If key-in time is less than t

, DTMF signal will last for tTD , otherwise the tone duration will

TD

),& minimum intertone pause time to support rapid

TD

last as long as the key is pressed.
Handfree input control pin.
Toggle input sturcture, falling edge trigger.
It is used to enable and disable Handfree function.
With waveshaped by a built-in Schmit trigger, the bounce of input can be eliminated by external R,
C debounce circuit.
A built-in pull up resistor is 200K typical.
Handfree output pin.
Inverter output structure (normally "low", active "high").
When a HFI pin is active, Handfree function will be enabled (HFO=1) or disabled (HFO=0).
When the Handfree function is enable (HFO=1), after OFF-HOOK action, it can reset Handfree
function and HFO pin return to "low" state.
Serial data output pin.
NMOS open drain output structure.
When there is a valid entry on keyboard, this pin will output a serial data.
This serial data is designed to drive LCD driver to display dialing number on LCD screen or drive
voice synthesizer to announce dialing number to speaker.
Key tone output pin for key pad input. The key tone duration is the same as the key pressed time.
No matter at Tone mode or pulse mode.
Inverter output structure.

FUNCTION DESCRIPTION

Keyboard Operation

Symbol definitions:

a). ↑ : OFF-HOOK or enable Hand Free function.
b). ↓ : ON-HOOK or disable Hand Free function.
c). : Input level from low to high.
d). : Input level from high to low.
e). D

.....Dn : Digit key; 1,2,3,4,5,6,7,8,9,0,*,# (C1.....Cn is same as D1.....Dn ).

1

f). D
g). D
h). t
i). t
j). t
k). t
l). t

... DPn: Pulse digit ; 1,2,3,4,5,6,7,8,9,0, (CP1... CPn is same as DP1... DPn).

P1

....Dtn: Tone digit ; 1,2,3,4,5,6,7,8,9,0,*, # (Ct1....Ctn is same as Dt1....Dtn).

t1
F
P
PT
FP
RP

: Flash time.
: Pause time.
: Pulse to Tone wait time.
: Pause time for flash.
: Pause time for redial.

m). LNB : Last number redial buffer.

* This specification are subject to be changed without notice.

10.1.1997

4

TONE/PULES SWITCHABLE DIALER WITH LCD INTERFACE

A. Normal Dialing

1. Digit Dialing

Procedure : ↑ D1,D2 . . . . . ., Dn↓

Dial out : Dt1, Dt2 . . . . . . ., Dtn in tone mode

Dial out : Dp1, Dp2 . . . . . ., Dpn in pulse mode

LNB : D1, D2 . . . . . . Dn

2. Dialing with flash key

Procedure : ↑ F,D1,D2 . . . . . ., Dn↓

Dial out : t
Dial out : t

, Dt1,Dt1 . . . . . . ., Dtn in tone mode

F

,Dp1,Dp1 . . . . . . ., Dpn in pulse mode

F

LNB : D1, D2 . . . . . . . Dn

3. Dialing with P→T key

Procedure : ↑ D1, D2 . . . . . .,P→T, . . . . . , Dn↓

Dial out : Dp1, Dp2, . . . . t

, . . . . . , Dtn in pulse mode

PT

LNB : D1, D2 . . . . . ,P→T, . . . . Dn

Note : If key in digit over maximum digit stored in LNB, then RD is inhibited even after on/off hook.

EM91810A/B

B. Mixed dialing

Procedure : ↑ D1, D2 . . . . . .,P→T, D9,D10, . . . . . , Dn↓

Dial out : Dp1, Dp2, . . . . t

, Dt9,Dt10 . . . . . , Dtn

PT

LNB : D1, D2 . . . . . ,P→T, D9,D10 . . . . Dn

C. Redial

LNB : D1, D2 . . . . . Dn

Procedure : ↑ RD ↓

Dial out : Dt1, Dt2, . . . . Dtn in tone mode

Dial out : Dp1, Dp2, . . . . Dpn in pulse mode

Note : If key in digit over maximum digit stored in LNB, then RD is inhibited.

D. Pause Function

Procedure : ↑ D1, D2, . . . .Dn, P, C1 . . . . .Cn↓

Dial out : Dt1, Dt2, . . . . Dtn , tp, Ct1 . . . . . . . . . Ctn in tone mode

Dial out : Dp1, Dp2, . . . . Dpn,tp, Cp1 . . . . . . . . .Cpn in pulse mode

LNB : D1, D2 . . . . . Dn, P, C1, C2 . . . . . . . . . .Cn

E. Flash Function

1. Reset

Procedure : ↑ D1, D2, . . . .Dn, F, C1 . . . . .Cn ↓

Dial out : Dt1, Dt2, . . . . Dtn , t

Dial out : Dp1, Dp2, . . . . Dpn, t

,Ct1 . . . . . . . . . Ctn in tone mode

F

,Cp1 . . . . . . . . .Cpn in pulse mode

F

LNB : C1, C2 . . . . . Cn

* This specification are subject to be changed without notice.

10.1.1997

5

Handfree function operation:

A). To execute Handfree function : When HFO = "low", HFI pin is active , the Handfree function will be
enabled (HFO="HIGH").
B). Reset Handfree function:

a. OFF-HOOK action.
b. When HFO="high", a HFI pin is active again , the Handfree function will be reset (HFO="LOW").

Operating flow chart of Handfree

EM91810A/B

TONE/PULSE SWITCHABLE DIALER WITH LCD INTERFACE

HF

ON HKS
HF LINE

STATE NO. PO XMUTE HFO

(0) INITIAL STATE F F 0
(1) ON HKS HF LINE F F 1
(2) OFF HKS LINE F F 0
(3) OFF HKS HF LINE F F 1

* F : Floating (Hi-impedance)

SDO (Serial Data Output) function

The SDO is serial data output which format is the same with UART protocol. SDO function is designed to drive
LCD driver and voice synthesizer to display dialing number on LCD screen and announce it to speaker. The SDO
signal consists of two start bits, six data bits and two stop bits.

(1)

OFF

ON

ON HKS
INITIAL

HF

OFF HKS

HF LINE

(0)

(3)

HF

OFF

HF

OFF HKS

ON

(2)

* Note :
ON : ON HKS
OFF : OFF HKS
HF : Depress HF key

0 1 Bit0 Bit1 Bit2 Bit3 Bit4 Bit5 0 1

Start bit Data bits

LSB

The frequency of every bit is 256Hz (about 3.9 ms)
There are two categories of dialing data, and representation of serial data is as the following:

(b5,b4=0,0) Digit key

Key 1234 56 78 9 0*#PP-T

b3b2b1b0 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110

Display 1 2 3 4 5 6 7 8 9 0 P

(b5,b4=1,0) Function key

Key HF F

b3b2b1b0 1010 1111

Display F

Note : */T key at pulse mode display " "

at tone mode display " "

* This specification are subject to be changed without notice.

MSB

Stop bit

10.1.1997

6

TEST CIRCUIT

E

EM91810A/B

TONE/PULES SWITCHABLE DIALER WITH LCD INTERFACE

1

KEY

BOARD

3

COUNTER
AND
AC METER

10K

**

DIST.(dB)= 20log

5

TONE

V+

A

HKS

V

DD

Operation current

MODE

V

SS

Tone output voltage

.

V+

V

DD

V

HKS

SS

√(V1)**2+(V2)**2+..+(Vn)**2

√(VL)**2+(VH)**2

Pulse output sink current(

V

+

open drain structure)

DP
DP
DT

KEYBOARD
ENTRY

2

V+

Standby current

A

V

4

10K

SPECTRUM
ANALYZER

DD

V

SS

V+

TONE

V

DD

V

HKS

HKS

Tone distortion

V

SS

KEYBOARD

ENTRY

a. V1....Vn are extraneous frequencies (ie, inter modulation and

harmonic)
components in the 500Hz to 3400Hz band.

b. VL,VH are the individual frequency components of the

DTMF signal

c. Whether keyboard is pushed refer to the TONE mode time

diagram

6

V

+

Keypad input

V

HKS

DD

V

SS

V

+

V

DD

V

MODE

SS

Flash Key

R

*

C

*

A

PO

V

VEXT

7

Column

A

HKS

Isink=I/(1-Duty Cycle) I is the net DC current measured from
ampere meter.

R* , C* mean others column and row.

* This specification are subject to be changed without notice.

A

ROW

HKS

V

DD

V

MOD

SS

R

*

C

*

10.1.1997

7

EM91810A/B

TONE/PULSE SWITCHABLE DIALER WITH LCD INTERFACE

ABSOLUTE MAXIMUM RATINGS (Ambient Temperature is 25°C, All voltage referenced to V

. )

SS

Parameter Sym. Ratings Unit

Power Supply Voltage V
Input Voltage Range V
Operating Temperature T
Storage Temperate T
Power Dissipation P

DD

IN
OPR
STO
D

6.0 V

-0.3 ~ VDD + 0.3 V
0 ~ 50 ˚C

-55 ~125 ˚C
500 mw

ELECTRICAL CHARACTERISTICS (I) (Ambient Temperature is 25°C, All voltage referenced to V

unless otherwise noted.)
(General purpose specification, fosc. = 3.579545 MHz)

Parameter Sym. Conditions Min. Typ. Max. Unit

Operating Voltage V

Operating Current Iop

Standby Current Is
Memory retention current Imr
Control pin input voltage Vil

Vih

XMUTE pin

leakage current Imth

sink current Imtl
HKS pin input current Ihks
Keyboard scanning pin

drive current Ikbd

sink current Ikbs
Key-in debounce time t

DB

HFI pin input resistor Rhfi
HFO pin

drive current Ihdoh

sink current Ihdol

Tone 2.5 - 5.5

DD

Pulse 2.0 - 5.5 V
Memory retension 1.0 - 5.5
Tone - 0.6 2 mA

OFF-HOOK, Keypad entry

Pulse - 0.2 0.5 mA
ON-HOOK, No Keypad entry - 0.1 1 µA
ON-HOOK, V

= 1.0V - 0.1 0.2 µA

DD

V

0.7V

SS

DD

- 0.3V

-VDDV

Vxmute = 6.0V - - 1 µA
Vxmute = 0.5V 0.2 0.5 - mA
Vhks = 2.5V - - 0.1 µA

*Vn = 0V, 4 10 30 µA
*Vn = 2.5V, 200 400 800 µA

-20- ms

Vhfi=0 - 200 - KΩ

Vhfo = 2.0V 0.5 - - mA
Vhfo = 0.5V 0.5 - - mA

DD

, VDD = 2.5V,

SS

V

* Vn : Input voltage of any keyboard scanning pin (Row group, Column group).

* This specification are subject to be changed without notice.

10.1.1997

8

EM91810A/B

TONE/PULES SWITCHABLE DIALER WITH LCD INTERFACE

ELECTRICAL CHARACTERISTICS (II) (Ambient Temperature is 25°C, All voltage referenced to V

unless otherwise noted.)
(Pulse mode specification, fosc. = 3.579545 MHz)

Parameter Sym. Conditions Min. Typ. Max. Unit

Pulse output pin,SDO pin

leakage current Ipoh
sink current Ipol

Pulse rate fpr

Vpo = 2.5V - - 0.1 uA
Vpo = 0.5V 0.5 - - mA

- 10 - pps

- 20 - pps

Make/Break ratio TM:TB

- 40:60 - %

- 33:66 - %

Pre-digit Pause t

PDP

M/B ratio = 40:60 - 40 - ms
M/B ratio = 33:66 - 33 - ms

Inter-digit Pause t

IDP

Pulse rate = 10pps - 800 - ms
Pulse rate = 20pps - 500 - ms

ELECTRICAL CHARACTERISTICS (III) (Ambient Temperature is 25 °C, All voltage referenced to V

unless otherwise noted.)
(TONE mode specification, fosc. = 3.579545 MHz)

, VDD = 2.5V,

SS

, VDD = 2.5V,

SS

Parameter Sym. Conditions Min. Typ. Max. Unit

TONE output pin

DC level Vdc
sink current Itl
AC level Vdtmf
Load resistor Rl

VDD = 2.0V~5.5V 0.5V
Vdtmf = 0.5V 0.2 - - mA
Row group, RL = 10K
Dist.

≤ -23dB 10 - - KΩ

DTMF signal:

pre-emphasis twist

*distortion Dist.
Minimum tone duration t
Minimum intertone t

TD

ITP

VDD = 2.0~5.5V, Column-Row group 1 2 3 dB
RL = 10K

Ω - -30 -23 dB

Auto redial - 98/83 - ms
Auto redial - 98/83 - ms

pause

* Distortion (dB) = 20 log { [(V

1

+ V

2

+ V

2

+...+Vn)

3

1/2

] / [(V

2

2

VL , VH : Row group and Column group signal.

V1 ,V2 ,...., Vn : Harmonic signal (BW = 300 Hz~ 3500 Hz).

* Actual frequency output (fosc. = 3.579545 MHz)

KEYBOARD SCANNING PIN STANDARD (Hz) OUTPUT (Hz) DEVIATION (%)

R1 f1 697 699 +0.28
R2 f2 770 766 -0.52

R3 f3 852 848 -0.47
R4 f4 941 948 +0.74
C1 f5 1209 1216 +0.57
C2 f6 1336 1332 -0.30
C3 f7 1477 1472 -0.34

- 0.7V

DD

Ω 130 155 170 mVrms

2

2

L

+ V

1/2

)

]}.

H

DD

V

* This specification are subject to be changed without notice.

10.1.1997

9

HKS

EM91810A/B

TONE/PULSE SWITCHABLE DIALER WITH LCD INTERFACE

KEY IN

XMUTE

PO

TONE

OSCO

SDO

3 2 3

t

DB

t

ITP

t

ITP

NORMAL DIALING

Figure 2: Tone Mode Timing Diagram

t

TD

t

ITP

- - - - - - High impedance

HKS

KEY IN

XMUTE

PO

TONE

OSCO

SDO

3

t

PDP

t

2 3

t

DB

t

IDP

t

M

B

t

IDP

NORMAL DIALING

Figure 3: Pulse Mode Timing Diagram

t

IDP

t

M

- - - - - - High impedance

* This specification are subject to be changed without notice.

10.1.1997

10

HKS

EM91810A/B

TONE/PULES SWITCHABLE DIALER WITH LCD INTERFACE

HKS

t

P->T

IDP

3

T

pt

- - - - - - High impedance

KEY IN

XMUTE

PO

TONE

OSCO

SDO

3

t

PDP

t

DB

t

IDP

2

Figure 4: Timing Waveform for mixed dialing Operation (by P→T key entry)

t

ITP

KEY IN

XMUTE

PO

TONE

OSCO

SDO

1 2

t

DB

t

ITP

Figure 5: Tone Mode Redial Timing Diagram

t

ITP

AUTO DIALING

RD

t

ITP

t

t

D

- - - - - - High impedance

ITP

* This specification are subject to be changed without notice.

10.1.1997

11

HKS

EM91810A/B

TONE/PULSE SWITCHABLE DIALER WITH LCD INTERFACE

KEY IN

XMUTE

XMUTE

PO

TONE

OSCO

SDO

3

t

DB

HKS

KEY IN

2

t

IDP

t

IDP

Figure 6: Pulse Mode Redial Timing Diagram

3

2

P

3

RD

t

IDP

t

IDP

- - - - - - High impedance

*PULSE MODE:

XMUTE

PO

TONE

OSCO

*TONE MODE:

XMUTE

PO

TONE

OSCO

SDO

t

PDP

t

t

DB

DB

t

t

ITP

IDP

t

t

ITP

IDP

T

P

T

p

t

t

ITP

IDP

- - - - - - High impedance

Figure 7: Pause key operating timing

* This specification are subject to be changed without notice.

10.1.1997

12

HKS

EM91810A/B

TONE/PULES SWITCHABLE DIALER WITH LCD INTERFACE

KEY IN

XMUTE

PO

TONE

OSCO

SDO

F

t

DB

T

F

Figure 8: Flash key operation timimg

- - - - - - High impedance

HKS

KEY IN

SDO

2

TSTSb0b1b2b3b4b5TSPT

SP

0 1 0 1 0 0 0 0 0 1

Figure 9: SDO operation timimg

* This specification are subject to be changed without notice.

10.1.1997

13

APPLICATION CIRCUIT

EM91810A/B

TONE/PULSE SWITCHABLE DIALER WITH LCD INTERFACE

220K

100µ/16V

2K7

Z.D.

5V1

2K2

ZNR

IN4148

MPSA42

120V

IN4148

22M

100K

MPSA92

HOOK SW

EM91810A Application Example

IN4004*4

OFF

ON

330K

IN4148

240K

100K

100µ

.1µ

470K

16V

C945

11

13

SDO

161718

F

P→T
369

258

TO HANDSEET

LCD Driver

LCD PANEL

SS

OSCI OSCO V

R4

15

P

R/P

#

0

1.5V

568

3.579545MHz

820k*6

TONE

20PPS

20PPS

VDD

100K

2 WIRE TO 4 WIRE

SPEECH NETWORK

1µ

7

10

14

12

DD

V

HKS

PO

KT

TONE

EM91810A

C1C2C3

412

XMUTE

C4 R1R2R3

3

Tip

Ring

* This specification are subject to be changed without notice.

*

7

1

4

10.1.1997

14

APPLICATION CIRCUIT

C945

200

.02µ

EM91810A/B

TONE/PULES SWITCHABLE DIALER WITH LCD INTERFACE

F

P

RD

P→T

369

2 TO 4 WIRE

AUDIO AMPLIFIER

SPEECH NETWORK &

TO HANDSET

258

147

#

0

*

DD

V

10PPS

20PPS

TONE

22M

IN4148

100K

MPSA92

330K

ZNR

2K2

120V

IN4148

200K

0.1µF

470K

C945

240K

+

100µ

7

12

11

KT

TONE

DD

13 16

5V1

.1µ

16V

+

100K

V

EM91810B

PO

C945

HFI

9

100K

.1µ

HF

47K

KEY

HKS

14

15

1µ

47K

3K3

HFO

XMUTE

OSCI

5

3.579545 MHz

HFO

6

OSCO

18

R1

SDO

10

192017

R2

R3

4

R4

C1

C4 C3 C2

SS

V

LCD Driver

1.5V

820K*6

21
3

8

.001µ

SW

LCD PANEL

HOOK ON

IN4004*4

Tip

Ring

* This specification are subject to be changed without notice.

10.1.1997

15

PACKAGE INFORMATION

Example :

EM 91215 P
(1) (2) (3)

18/20/28 Lead Plastic Package

EM91810A/B

TONE/PULSE SWITCHABLE DIALER WITH LCD INTERFACE

(1) ELAN MICRO. pefix
(2) Type number
(3) Package code:

P→PDIP
K→Skinny
R→SDIP

E1

E

eB

18 PDIP

MILIMETERS INCHES

DIM MIN. MAX. MIN. MAX.

A - 5.334 - .210

A1 0.381 - .015 -

B 0.356 0.558 .014 .022

B1 1.150 1.778 .045 .070

C 0.204 0.381 .008 .015
D 22.35 23.37 .880 .920

E 7.620 8.255 .300 .325

E1 6.096 7.112 .240 .280

e 2.286 2.794 .090 .110

eB - 10.92 - .430

L 2.921 4.064 .115 .160

1

C

B

e

20 PDIP

MILIMETERS INCHES

DIM MIN. MAX. MIN. MAX.

A - 5.334 - .210

A1 0.381 - .015 -

B 0.356 0.558 .014 .022

B1 1.150 1.778 .045 .070

C 0.204 0.381 .008 .015

D 25.40 26.67 1.000 1.050

E 7.620 8.255 .300 .325

E1 6.096 7.112 .240 .280

e 2.286 2.794 .090 .110

eB - 10.92 - .430

L 2.921 4.064 .115 .160

D

A

A1

L

B1

28 PDIP

MILIMETERS INCHES

DIM MIN. MAX. MIN. MAX.

A - 6.350 - .250

A1 0.381 - .015 -

B 0.356 0.558 .014 .022

B1 1.016 1.778 .040 .070

C 0.204 0.381 .008 .015

D 35.56 37.85 1.400 1.490

E 15.24 15.88 .600 .625

E1 13.21 14.73 .520 .580

e 2.286 2.794 .090 .110

eB - 17.78 - .700

L 2.921 5.080 .115 .200

* This specification are subject to be changed without notice.

10.1.1997

16

22/24 Lead Plastic Package-Skinny

EM91810A/B

TONE/PULES SWITCHABLE DIALER WITH LCD INTERFACE

E1

1

E

C

B

eB

22 PDIP (skinny)

MILIMETERS INCHES

DIM MIN. MAX. MIN. MAX.

A - 4.752 - .180
A1 0.381 - .015 ­B 0.356 0.558 .014 .022
B1 1.27 1.778 .050 .070
C 0.204 3.556 .008 .014
D 25.90 26.67 1.02 1.05
E 7.620 8.255 .300 .325
E1 6.223 6.604 .245 .260
e 2.286 2.794 .090 .110
eB 8.382 10.16 .330 .400
L 2.921 4.064 .115 .160

D

A

A1

e

B1

L

24 PDIP (skinny)

MILIMETERS INCHES

DIM MIN. MAX. MIN. MAX.

A - 4.572 - .180
A1 0.381 - .015 ­B 0.356 0.558 .014 .022
B1 1.27 1.778 .050 .070
C 0.204 0.381 .008 .015
D 31.24 32.26 1.23 1.270
E 7.620 8.255 .300 .325
E1 6.223 6.731 .245 .265
e 2.286 2.794 .090 .110
eB 8.636 9.652 .340 .380
L 2.921 4.064 .115 .160

* This specification are subject to be changed without notice.

10.1.1997

17

42 SDIP Package

EM91810A/B

TONE/PULSE SWITCHABLE DIALER WITH LCD INTERFACE

E1

E

C

D1

eB

B

e

B1

D

A2

A

A1

L

42 SDIP

MILIMETERS INCHES

DIM MIN. MAX. MIN. MAX.

A - 5.08 - 0.200
A1 0.381 - 0.015 ­A2 3.937 4.191 0.155 0.165
B 0.356 0.559 0.014 0.022
B1 0.914 1.116 0.036 0.044
C 0.204 0.304 0.008 0.012
D 36.70 37.34 1.445 1.470
E1 13.84 14.10 0.545 0.555
e 1.727 1.829 0.068 0.072
eB 15.24 17.78 0.600 0.70
D1 0 0.127 0 0.005
L 2.921 3.429 0.115 0.135

* This specification are subject to be changed without notice.

10.1.1997

18