Datasheet BU1507AX Datasheet (Philips)

Page 1

Philips Semiconductors Product specification

Silicon Diffused Power Transistor BU1507AX

GENERAL DESCRIPTION

Enhanced performance, new generation, high-voltage, high-speed switching npn transistor in a plastic full-pack envelope intended for use in horizontal deflection circuits of colour television receivers and computer monitors. Features exceptional tolerance to base drive and collector current load variations resulting in a very low worst case dissipation.

QUICK REFERENCE DATA

SYMBOL PARAMETER CONDITIONS TYP. MAX. UNIT

CESM

CEO

tot

CEsat

Csat

PINNING - SOT186A PIN CONFIGURATION SYMBOL

Collector-emitter voltage peak value VBE = 0 V - 1500 V Collector-emitter voltage (open base) - 700 V Collector current (DC) - 8 A Collector current peak value - 15 A Total power dissipation Ths ≤ 25 ˚C - 45 W Collector-emitter saturation voltage IC = 4 A; IB = 0.95 A - 1.0 V Collector-emitter saturation voltage IC = 4 A; IB = 0.8 A - 5.0 V Collector saturation current f = 16kHz 4 - A Fall time I

= 4 A; f = 16kHz 0.25 0.5 µs

Csat

PIN DESCRIPTION

case

1 base 2 collector

3 emitter

case isolated

LIMITING VALUES

Limiting values in accordance with the Absolute Maximum Rating System (IEC 134)

SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT

CESM

CEO

-I

B(AV)

-I

tot

stg

Collector-emitter voltage peak value VBE = 0 V - 1500 V Collector-emitter voltage (open base) - 700 V Collector current (DC) - 8 A Collector current peak value - 15 A Base current (DC) - 4 A Base current peak value - 6 A Reverse base current average over any 20 ms period - 100 mA Reverse base current peak value

Total power dissipation Ths ≤ 25 ˚C - 45 W Storage temperature -65 150 ˚C Junction temperature - 150 ˚C

THERMAL RESISTANCES

123

-5A

SYMBOL PARAMETER CONDITIONS TYP. MAX. UNIT

th j-hs

th j-a

1 Turn-off current.

Junction to heatsink with heatsink compound - 3.7 K/W Junction to ambient in free air 55 - K/W

October 1997 1 Rev 1.100

Page 2

Philips Semiconductors Product specification

Silicon Diffused Power Transistor BU1507AX

ISOLATION LIMITING VALUE & CHARACTERISTIC

Ths = 25 ˚C unless otherwise specified

SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT

isol

STATIC CHARACTERISTICS

Ths = 25 ˚C unless otherwise specified

SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT

CES

EBO

CEOsust

CEsat

R.M.S. isolation voltage from all f = 50-60 Hz; sinusoidal - 2500 V three terminals to external waveform; heatsink R.H. ≤ 65% ; clean and dustfree

Capacitance from T2 to external f = 1 MHz - 10 - pF heatsink

Collector cut-off current

VBE = 0 V; VCE = V VBE = 0 V; VCE = V Tj = 125 ˚C

CESMmax CESMmax

- - 1.0 mA

- - 2.0 mA

Emitter cut-off current VEB = 7.5 V; IC = 0 A - - 1.0 mA Emitter-base breakdown voltage IB = 1 mA 7.5 13.5 - V Collector-emitter sustaining voltage IB = 0 A; IC = 100 mA; 700 - - V

L = 25 mH

Collector-emitter saturation voltages IC = 4 A; IB = 0.8 A - - 5.0 V V h

BEsat

FE FE

Base-emitter saturation voltage IC = 4 A; IB = 0.8 A - - 1.1 V

DC current gain IC = 100 mA; VCE = 5 V - 17 -

IC = 4 A; VCE = 5 V 5.0 7.0 9.0

DYNAMIC CHARACTERISTICS

Ths = 25 ˚C unless otherwise specified

SYMBOL PARAMETER CONDITIONS TYP. MAX. UNIT

Collector capacitance IE = 0 A; VCB = 10 V; f = 1 MHz 68 - pF

Switching times (16 kHz line I

deflection circuit) -VBB = 4 V

= 4 A; I

Csat

= 0.7 A; LB = 6 µH;

B(end)

Turn-off storage time 5.0 6.0 µs

Turn-off fall time 0.25 0.5 µs

2 Measured with half sine-wave voltage (curve tracer).

October 1997 2 Rev 1.100

Page 3

Philips Semiconductors Product specification

Silicon Diffused Power Transistor BU1507AX

TRANSISTOR

VCE

DIODE

26us20us

64us

Fig.1. Switching times waveforms.

90 %

10 %

IBend

ICsat

IBend

hFE

100

VCE = 1 V

0.01 0.1 1 10 100

BU2507AF/X

Ths = 25 C Ths = 85 C

IC / A

Fig.4. High and low DC current gain. hFE = f (IC)

VCE = 1 V

hFE

100

VCE = 5 V

BU2507AF/X

Ths = 25 C Ths = 85 C

IBend

-VBB

- IBM

Fig.2. Switching times definitions.

+ 150 v nominal adjust for ICsat

T.U.T.

Cfb

Fig.3. Switching times test circuit

0.01 0.1 1 10 100

IC / A

Fig.5. High and low DC current gain. hFE = f (IC)

VCE = 5 V

VCEsat / V

Ths = 25 C Ths = 85 C

0.1

0.01

0.1

Fig.6. Typical collector-emitter saturation voltage.

110

VCEsat = f (IC); parameter IC/I

BU2507AF/X

IC/IB = 3 IC/IB = 4 IC/IB = 5

IC / A

100

October 1997 3 Rev 1.100

Page 4

Philips Semiconductors Product specification

Silicon Diffused Power Transistor BU1507AX

VBEsat / V

1.2

1.1

0.9

0.8

0.7

0.6 0 0.5 1 1.5 2

BU2507AF/AX

Ths = 25 C Ths = 85 C

IC = 4 A

IC = 3 A

IB / A

Fig.7. Typical base-emitter saturation voltage.

VBEsat = f (IB); parameter I

Ptot / W

0.1

0 0.5 1 1.5 2

IB / A

BU2507AF/DF/AX/DX

Ths = 25 C Ths = 85 C

Fig.8. Typical losses.

= f (IB); IC = 4 A; f = 16 kHz

TOT

PD%

120 110 100

90 80 70 60 50 40 30 20 10

0 20 40 60 80 100 120 140

Normalised Power Derating

with heatsink compound

Ths / C

Fig.10. Normalised power dissipation.

PD% = 100⋅PD/P

Zth / K/W

0.5

0.2

0.1

0.05

0.1

0.02

0.01

D = 0

0.001 1E-06 1E-4 10E-2 1E+00

D 25˚C

t / s

= f (Tmb)

BU2507AF/X/DF/X

Fig.11. Transient thermal impedance.

= f(t); parameter D = tp/T

th j-hs

D =

ts/tf/ us

0 0.5 1 1.5 2

BU2507AF/AX/Df/DX85ts/tf

IB / A

Fig.9. Typical collector storage and fall time.

ts = f (IB); tf = f (IB); IC = 4.0 A; Tj = 85˚C; f = 16 kHz

October 1997 4 Rev 1.100

Page 5

Philips Semiconductors Product specification

Silicon Diffused Power Transistor BU1507AX

MECHANICAL DATA

Dimensions in mm Net Mass: 2 g

10.3

Recesses (2x)

2.5

0.8 max. depth

3 max.

not tinned

13.5 min.

0.4

max

3.2

3.0

123

5.08

2.8

2.54

15.8 max.

max.

seating

plane

0.5

2.5

4.6

max

2.9 max

6.4

0.6

2.5

15.8 max

Fig.12. SOT186A; The seating plane is electrically isolated from all terminals.

1.3

1.0 (2x)

0.9

0.7

Notes

1. Refer to mounting instructions for F-pack envelopes.

2. Epoxy meets UL94 V0 at 1/8".

October 1997 5 Rev 1.100

Page 6

Philips Semiconductors Product specification

Silicon Diffused Power Transistor BU1507AX

DEFINITIONS

Data sheet status

Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specifications.

Limiting values

Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of this specification is not implied. Exposure to limiting values for extended periods may affect device reliability.

Application information

Where application information is given, it is advisory and does not form part of the specification.

 Philips Electronics N.V. 1997

All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.

The information presented in this document does not form part of any quotation or contract, it is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights.

LIFE SUPPORT APPLICATIONS

These products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale.

October 1997 6 Rev 1.100