Datalogic Scanning D8530 User Manual

PowerScan® D8530
Reference Manual
Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 USA Telephone: (541) 683-5700 Fax: (541) 345-7140
An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written per-mission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic Scanning”). Owners of Datalogic products are hereby granted a non-exclusive, revocable license to reproduce and transmit this documentation for the purchaser's own internal business purposes. Purchaser shall not remove or alter any proprietary notices, including copyright notices, contained in this documentation and shall ensure that all notices appear on any reproductions of the documentation. Should future revisions of this manual be published, you can acquire printed versions by contacting your Datalogic representative. Electronic versions may either be downloadable from the Datalogic website (www.scanning.datalogic.com) or provided on appropriate media. If you visit our website and would like to make comments or suggestions about this or other Datalogic publications, please let us know via the "Contact Datalogic" page.
Disclaimer
Datalogic has taken reasonable measures to provide information in this manual that is complete and accurate, however, Datalogic reserves the right to change any specification at any time without prior notice. Datalogic is a registered trademark of Datalogic S.p.A. in many countries and the Datalogic logo is a trademark of Datalogic S.p.A. all licensed to Datalogic Scanning, Inc. All other trademarks and trade names referred to herein are property of their respective owners.
20/02/2008
ii
CONTENTS
GENERAL VIEW .......................................................................................... v
COMPLIANCE.............................................................................................. v
FCC Compliance...........................................................................................vi
Laser Safety..................................................................................................vi
WEEE Compliance ....................................................................................... x
Power Supply................................................................................................xi
PATENTS .................................................................................................... xi
SERVICE AND SUPPORT ......................................................................... xii
1 INTRODUCTION ..........................................................................................1
1.1 PowerScan® D8530 Family Description....................................................... 1
1.2 Package Contents......................................................................................... 1
1.3 Configuration Methods.................................................................................. 2
1.3.1 Reading Configuration Codes....................................................................... 2
1.3.2 Using Datalogic Aladdin™ ............................................................................2
1.3.3 Sending Configuration Strings from Host...................................................... 2
1.4 CABLE CONNECTION ................................................................................. 3
2 USING POWERSCAN® D8530.................................................................... 5
2.1 Aiming System.............................................................................................. 5
2.2 Normal Operation.......................................................................................... 6
2.3 Image Capturing ........................................................................................... 6
2.3.1 Basic Configuration Parameters ...................................................................7
2.3.2 Advanced Configuration Parameters ............................................................ 8
2.4 Autoscanning ................................................................................................ 8
2.4.1 Normal Mode ................................................................................................ 8
2.4.2 Pattern Mode ................................................................................................8
2.5 Camera Control............................................................................................. 9
2.6 Defining Data Formatting ............................................................................ 10
2.6.1 Concatenation............................................................................................. 11
3 INITIAL SETUP ..........................................................................................12
3.1 RS-232 Interface Selection ......................................................................... 12
iii
3.2
Wedge Interface Selection.......................................................................... 13
3.3 USB Interface Selection.............................................................................. 14
4 CONFIGURATION USING CODE SYMBOLS ...........................................17
4.1 Default Settings........................................................................................... 18
4.2 Changing Default Settings ..........................................................................23
4.3 Advanced Data Format ............................................................................... 88
4.3.1 Format Definition......................................................................................... 89
4.3.2 Match Conditions ...................................................................................... 106
4.3.3 Format Enable/Disable ............................................................................. 108
4.3.4 Mismatch Result ....................................................................................... 109
5 REFERENCES ......................................................................................... 110
5.1 RS-232 – USB COM ................................................................................. 110
5.1.1 ACK/NACK Protocol ................................................................................. 110
5.1.2 RX Timeout............................................................................................... 110
5.2 USB Keyboard .......................................................................................... 111
5.2.1 Keyboard Speed ....................................................................................... 111
5.3 Code Selection.......................................................................................... 111
5.3.1 Issue Identical Codes................................................................................ 111
5.4 Reading Parameters ................................................................................. 111
5.4.1 Safety Time............................................................................................... 111
5.5 Configuration Editing Commands ............................................................. 112
6 TEST CODE SYMBOLS........................................................................... 113
7 MAINTENANCE .......................................................................................115
8 TECHNICAL FEATURES......................................................................... 116
8.1 Indicators ..................................................................................................120
8.1.1 PowerScan® D8530 LED Indicators......................................................... 120
8.1.2 Beeper ......................................................................................................120
8.1.3 Good Read Spot ....................................................................................... 120
Function Description ................................................................................. 133
iv

GENERAL VIEW

p
w
LEDs
Cable Connector

COMPLIANCE

POWERSCAN® D8530 Reader Product Labels
POWERSCAN® D8530 Reader
Aiming System Imager
Beam Out
ut Windo
v

CE COMPLIANCE

This is a Class A product . In a domestic environment this product may cause radio interference, in which case the user may be
WARNING
required to take adequate measures.

FCC COMPLIANCE

Modifications or changes to this equipment without the expressed written approval of Datalogic could void the authority to use this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference which may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

LASER SAFETY

The PowerScan® D8530 hand-held reader is a Class 1 LED product regarding its Illuminator and a Class 2 laser product regarding its Aiming System.

LED Illuminator

The use of an illuminator in the PowerScan® D8530 Family is a Class 1 LED product:
ILLUMINATORE LED CLASSE 1
AUSLEUCHTER LED KLASSE 1
ILLUMINATEUR A LED DE CLASSE 1
ILUMINADOR LED DE CLASE 1
vi

Aiming System

The PowerScan® D8530 aiming system meets the requirements for laser safety.
I D F E
LA LUCE LASER È VISIBILE ALL'OCCHIO UMANO E VIENE EMESSA DALLA FINESTRA INDICATA NELLA FIGURA.
LUCE LASER NON FISSARE IL FASCIO
APPARECCHIO LASER DI CLASSE 2 MASSIMA POTENZA D'USCITA: LUNGHEZZA D'ONDA EMESSA: CONFORME A EN 60825-1 (2001)
DIE LASER­STRAHLUNG IST FÜR DAS MENSCHLICHE AUGE SICHTBAR UND WIRD AM STRAHLAUS­TRITTSFENTSTER AUSGESENDET (SIEHE BILD)
LASERSTRAHLUNG NICHT IN DEN STRAHL BLICKEN PRODUKT DER LASERKLASSE 2 MAXIMALE AUSGANGSLEISTUNG: WELLENLÄGE: ENTSPR. EN 60825-1 (2001)
LE RAYON LASER EST VISIBLE À L'OEUIL NU ET IL EST ÉMIS PAR LA FENÊTRE DÉSIGNÉE SUR L'ILLUSTRATION DANS LA FIGURE
RAYON LASER EVITER DE REGARDER LE RAYON APPAREIL LASER DE CLASSE 2 PUISSANCE DE SORTIE: LONGUER D'ONDE EMISE: CONFORME A EN 60825-1 (2001)
LA LUZ LÁSER ES VISIBLE AL OJO HUMANO Y ES EMITIDA POR LA VENTANA INDICADA EN LA FIGURA.
RAYO LÁSER NO MIRAR FIJO EL RAYO APARATO LÁSER DE CLASE 2 MÁXIMA POTENCIA DE SALIDA: LONGITUD DE ONDA EMITIDA: CONFORME A EN 60825-1 (2001)
ENGLISH
The following information is provided to comply with the rules imposed by international authorities and refers to the correct use of your terminal.
STANDARD LASER SAFETY REGULATIONS This product conforms to the applicable requirements of both CDRH 21 CFR 1040
and EN 60825-1 at the date of manufacture. For installation, use and maintenance, it is not necessary to open the device.
Use of controls or adjustments or performance of procedures other than those specified herein may result in exposure to hazardous
WARNING
visible laser light.
The product utilizes a low-power laser diode. Although staring directly at the laser beam momentarily causes no known biological damage, avoid staring at the beam as one would with any very strong light source, such as the sun. Avoid allowing the laser beam to hit the eye of an observer, even through reflective surfaces such as mirrors, etc.
vii
ITALIANO
Le seguenti informazioni vengono fornite dietro direttive delle autorità internazionali e si riferiscono all’uso corretto del terminale.
NORMATIVE STANDARD PER LA SICUREZZA LASER Questo prodotto risulta conforme alle normative vigenti sulla sicurezza laser alla data
di produzione: CDRH 21 CFR 1040 e EN 60825-1. Non si rende mai necessario aprire l’appa-recchio per motivi di installazione, utilizzo o manutenzione.
L'utilizzo di procedure o regolazioni differenti da quelle descritte nella documentazione può provocare un'esposizione pericolosa
ATTENZIONE
a luce laser visibile.
Il prodotto utilizza un diodo laser a bassa potenza. Sebbene non siano noti danni riportati dall’occhio umano in seguito ad una esposizione di breve durata, evitare di fissare il raggio laser così come si eviterebbe qualsiasi altra sorgente di luminosità intensa, ad esempio il sole. Evitare inoltre di dirigere il raggio laser negli occhi di un osservatore, anche attraverso superfici riflettenti come gli specchi.
DEUTSCH
Die folgenden Informationen stimmen mit den Sicherheitshinweisen überein, die von internationalen Behörden auferlegt wurden, und sie beziehen sich auf den korrekten Gebrauch vom Terminal.
NORM FÜR DIE LASERSICHERHEIT Dies Produkt entspricht am Tag der Herstellung den gültigen EN 60825-1 und CDRH
21 CFR 1040 Normen für die Lasersicherheit. Es ist nicht notwendig, das Gerät wegen Betrieb oder Installations-, und Wartungs­arbeiten zu öffnen.
Jegliche Änderungen am Gerät sowie Vorgehensweisen, die nicht in dieser Betriebsanleitung beschreiben werden, können ein
ACHTUNG
gefährliches Laserlicht verursachen.
Der Produkt benutzt eine Laserdiode. Obwohl zur Zeit keine Augenschäden von kurzen Einstrahlungen bekannt sind, sollten Sie es vermeiden für längere Zeit in den Laserstrahl zu schauen, genauso wenig wie in starke Lichtquellen (z.B. die Sonne). Vermeiden Sie es, den Laserstrahl weder gegen die Augen eines Beobachters, noch gegen reflektierende Oberflächen zu richten.
FRANÇAIS
Les informations suivantes sont fournies selon les règles fixées par les autorités internationales et se réfèrent à une correcte utilisation du terminal.
viii
NORMES DE SECURITE LASER Ce produit est conforme aux normes de sécurité laser en vigueur à sa date de
fabrication: CDRH 21 CFR 1040 et EN 60825-1. Il n’est pas nécessaire d’ouvrir l’appareil pour l’installation, l’utilisation ou l’entretien.
L'utilisation de procédures ou réglages différents de ceux donnés ici peut entraîner une dangereuse exposition à lumière laser
ATTENTION
visible.
Le produit utilise une diode laser. Aucun dommage aux yeux humains n’a été constaté à la suite d’une exposition au rayon laser. Eviter de regarder fixement le rayon, comme toute autre source lumineuse intense telle que le soleil. Eviter aussi de diriger le rayon vers les yeux d’un observateur, même à travers des surfaces réfléchissantes (miroirs, par exemple).
ESPAÑOL
Las informaciones siguientes son presentadas en conformidad con las disposiciones de las autoridades internacionales y se refieren al uso correcto del terminal.
NORMATIVAS ESTÁNDAR PARA LA SEGURIDAD LÁSER Este aparato resulta conforme a las normativas vigentes de seguridad láser a la
fecha de producción: CDRH 21 CFR 1040 y EN 60825-1. No es necesario abrir el aparato para la instalación, la utilización o la manutención.
La utilización de procedimientos o regulaciones diferentes de aquellas describidas en la documentación puede causar una
ATENCIÓN
exposición peligrosa a la luz láser visible.
El aparato utiliza un diodo láser a baja potencia. No son notorios daños a los ojos humanos a consecuencia de una exposición de corta duración. Eviten de mirar fijo el rayo láser así como evitarían cualquiera otra fuente de luminosidad intensa, por ejemplo el sol. Además, eviten de dirigir el rayo láser hacia los ojos de un observador, también a través de superficies reflectantes como los espejos.
CAUTION
The POWERSCAN® D8530 Hand-Held Reader is not user­serviceable. Opening the case of the unit can cause internal damage and will void the warranty.
ix

WEEE COMPLIANCE

Waste Electrical and Electronic Equipment (WEEE) Statement

English

For informati (WEEE), please refer to the website at www.scanning.datalogic.com.

Italian

Per informazio consultare il sito Web www.scanning.datalogic.com.

French

Pour toute info veuillez consulter le site Internet www.scanning.datalogic.com.

German

Informationen zur Entsorgung von Elektro- und Elektronik- Altgeräten (WEEE) erhalten Sie auf der Webseite www.scanning.datalogic.com.

Spanish

Si desea información acerca de los procedimientos para el desecho de los residuos del equipo eléctrico y electrónico (WEEE), visite la página Web www.scanning.datalogic.com.

Portuguese

Para informaç Eletrônicos (WEEE - Waste Electrical and Electronic Equipment), consultar o site web www.scanning.datalogic.com.

Chinese

有关处理废弃电气电子设备 http://www.scanning.datalogic.com/

Japanese

廃電気電子機器(WEEE)の処理についての関連事項はDatalo www.scanning.datalogic.com, をご参照下さい。
on about the disposal of Waste Electrical and Electronic Equipment
ni sullo smaltimento delle apparecchiature elettriche ed elettroniche
rmation relative à l’élimination des déchets électroniques (WEEE),
ões sobre a disposição de Sucatagem de Equipamentos Eléctricos e
(WEEE)的信息, 请参考
Datalogic公司的网站:
gicのサイト
x
Loading...