Page 1
Quick Reference Guide
®
PowerScan D8530 Family
01/08
Page 2
Datalogic Scanning, Inc.
959 Terry Street
Eugene, Oregon 97402
USA
Telephone: (541) 683-5700
Fax: (541) 345-7140
An Unpublished Work - All rights reserved. No part of the contents of this
documentation or the procedures described therein may be reproduced or
transmitted in any form or by any means without prior written permission of
Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic
Scanning”). Owners of Datalogic products are hereby granted a non-exclusive,
revocable license to reproduce and transmit this documentation for the
purchaser's own internal business purposes. Purchaser shall not remove or
alter any proprietary notices, including copyright notices, contained in this
documentation and shall ensure that all notices appear on any reproductions of
the documentation.
Should future revisions of this manual be published, you can acquire printed
versions by contacting your Datalogic representative. Electronic versions may
either be downloadable from the Datalogic website
(www.scanning.datalogic.com) or provided on appropriate media. If you visit our
website and would like to make comments or suggestions about this or other
Datalogic publications, please let us know via the "Contact Datalogic" page.
DISCLAIMER
Datalogic has taken reasonable measures to provide information in this manual
that is complete and accurate, however, Datalogic reserves the right to change
any specification at any time without prior notice. Datalogic is a registered
trademark of Datalogic S.p.A. in many countries and the Datalogic logo is a
trademark of Datalogic S.p.A. all licensed to Datalogic Scanning, Inc. All other
trademarks and trade names referred to herein are property of their respective
owners.
Page 3
CONTENTS
Updates and Language Availability .................................................................................... iv
PowerScan® D8530 family Description................................................................................1
Using PowerScan® D8530 family .......................................................................................2
Indicators ............................................................................................................................3
Setup ..................................................................................................................................3
Connections........................................................................................................................4
Interface Selection ..............................................................................................................7
Wedge Keyboard Nationality...............................................................................................8
USB Keyboard Nationality...................................................................................................9
Reading Parameters .........................................................................................................10
Default Configuration ........................................................................................................11
Operating Test ..................................................................................................................13
Technical Features............................................................................................................14
Service and Support..........................................................................................................18
Warranty ...........................................................................................................................18
Patents..............................................................................................................................18
Compliance.......................................................................................................................19
iii
Page 4
UPDATES AND LANGUAGE AVAILABILITY
UK/US
The latest drivers and documentation updates for this product are available on
Internet.
Log on to: www.scanning.datalogic.com
I
Su Internet sono disponibili le versioni aggiornate di driver e documentazione di
questo prodotto. Questo manuale è disponibile anche nella versione italiana.
Collegarsi a: www.scanning.datalogic.com
F
Les versions mises à jour de drivers et documentation de ce produit sont
disponibles sur Internet. Ce manuel est aussi disponible en version française.
Cliquez sur: www.scanning.datalogic.com
D
Im Internet finden Sie die aktuellsten Versionen der Treiber und Dokumentation
für dieses Produkt. Die deutschsprachige Version dieses Handbuches ist auch
verfügbar.
Adresse : www.scanning.datalogic.com
E
En Internet están disponibles las versiones actualizadas de los drivers y
documentación de este producto. También está disponible la versión en
español de este manual.
Dirección Internet: www.scanning.datalogic.com
iv
Page 5
POWERSCAN® D8530 FAMILY
POWERSCAN® D8530 FAMILY DESCRIPTION
The present manual includes just a few commands to allow the startup of the
scanner and setting of the required interface. For complete configuration of the
scanner, refer to the PowerScan D8530 Reference Manual or the Aladdin
configuration program, both downloadable from the website and available on
the included CD ROM.
The PowerScan® D8530 Hand-Held Reader packs a lot of performance into an
attractive, rugged, hand-held device. It operates in commercial and industrial
environments as well as the front office.
Omni-directional
Operating
Decoding
Formatting and
Concatenating
Imaging
Autoscanning
Flash Memory
To read a symbol or capture an image, you simply
aim the reader and pull the trigger. Since
PowerScan® D8530 is a powerful omni-directional
reader, the orientation of the symbol is not
important.
Thanks to powerful algorithms, PowerScan® D8530
reliably decodes all major 1D (linear) barcodes, 2D
stacked codes (such as PDF417), 2D matrix symbols
(such as DataMatrix™), postal codes (such as
PLANET). The data stream — acquired from decoding
a symbol — is rapidly sent to the host. The reader is
immediately available to read another symbol.
The string of a decoded code may be processed
according to either a simple or advanced data
formatting and be concatenated to other codes (up to
4 different codes).
PowerScan® D8530 can also function as a camera
by capturing entire images or image portions of
labels, signatures, and other items. Two different
control modes are available for managing the camera
exposure and calibration.
An autoscan command causes the reader to scan
continuously and to monitor the central zone of its
reading area.
Flash technology allows the upgrade of the
PowerScan® D8530 reader as new symbologies are
supported or as improved decoding algorithms
become available.
1
Page 6
DATALOGIC
USING POWERSCAN® D8530 FAMILY
PowerScan® D8530 normally functions by capturing and decoding codes.
The PowerScan® D8530 reader uses an intelligent aiming system. By pulling
the trigger, the aiming system indicates a field of view, which should be
positioned over the code:
When you pull the trigger, a red beam illuminates the code. If the aiming system
is centered and the entire symbology is within the aiming system, you will get a
good read. The field of view changes size as you move the reader closer or
farther away from the code.
Linear barcode 2D Matrix symbol
Aiming System
Successful reading is signaled by an audible tone plus a good-read green LED.
Relative Size and Location of Aiming System Pattern
The PowerScan® D8530 hand-held reader aiming system is
designed for general reading and decoding of 1D and 2D symbols.
Some variation in reading distance will occur due to narrow bar
NOTE
width and other factors.
If reading codes positioned on reflective surfaces, it may be
necessary to tilt the reader with respect to the barcode and/or
set the Camera Control parameters. For configuring the Camera
Control parameters refer to the PowerScan® D8530 Reference
NOTE
Manual available on the website and the CD-ROM.
2
Page 7
POWERSCAN® D8530 FAMILY
INDICATORS
LED INDICATORS
The PowerScan® D8530 family uses green LED indicators to signal the
following reader functions:
STATUS BEHAVIOR
Power ON At power-on, the LEDs blink briefly, then
light up for 2 seconds to signal the power
supply is present.
Normal Function
BEEPER
The PowerScan® D8530 basic software provides beeper signals for
good/wrong reading and for indicating errors. Its tone, volume and duration can
be directly configured by using the codes given in the PowerScan® D8530
Reference Manual available on the website.
The application program can also manage the beeper (User Defined Beeper)
when the reader is controlled by a Host PC. It is possible to activate the beeper
by sending a command from the Host to the reader via the current
communication interface.
GOOD READ SPOT
A green Good-Read Spot will be projected in the field of view when the reading
is successful.
The LED lights up after a good decoding and
will switch off only at the next trigger press.
SETUP
1. Make connections between PowerScan® D8530 and the Host PC using
the correct interface cable (see the following sections).
2. Read the correct Interface Selection code.
Your reader is now ready to read codes using the default settings.
3
Page 8
DATALOGIC
CONNECTIONS
CONNECTING THE CABLE
c Slip the cover over the cable.
d Push the plastic boot into the
rubber gasket. Take care that the
tab on the plastic boot is aligned
with the notch in the rubber gasket.
e Push the plastic boot and gasket
into the handle. Ensure that the
“Front” marking on the plastic boot
is facing out, with the arrow
pointing towards the front of the
scanner.
f Insert the cable into the socket of
the plastic boot.
g Insert the cable spacer into the
cable wire and slide it towards the
handle.
h Push the cover along the cable
towards the reader, and hook it
over the yellow “tooth”.
i Insert the strain relief into the cover
and tighten the screw to fix the
whole assembly to the reader
handle.
A. Rubber gasket
B. Plastic boot
C. Cable spacer
D. Cover
E. Strain relief
Align
1
Notch
Arrow
Tab
4
Page 9
POWERSCAN® D8530 FAMILY
RS-232
WEDGE
The USB interface is compatible with:
Windows
®
98 (and later) IBM POS for Windows®
Mac OS 8.0 (and later) 4960 Operating System
USB
5
Page 10
DATALOGIC
START-UP
As with all USB devices, upon connection, the Host performs several checks by
communicating with the PowerScan® D8530™. During this phase the green
LED on the PowerScan® D8530™ reader blinks and normal operations are
suspended. The correct USB driver must be loaded before the PowerScan
D8530 is ready to read codes
For all systems, the correct USB driver for the default USB-KBD interface is
included in the Host Operating System and will either be loaded automatically or
will be suggested by the O.S. and should therefore be selected from the dialog
box (the first time only).
When configuring the USB-COM interface, the relevant files and drivers must be
installed from the USB Device Installation software, which can be downloaded
from the web site http://www.s
CD-ROM.
The reader is ready.
ng.datalogic.com or can be found on the
canni
6
Page 11
INTERFACE SELECTION
RS-232 WEDGE – IBM AT
AMHKHMFOHNGNENEIEPANHOGOCK
AGPEPJAMDKEOFMHMLJAKFEHFKK
AMGNPJCJGIIJCMCEGJMHNDOLLK
AIFBJLBGMHPLNKECPCGMBBIBOK
AAPHBAJJDAAGMGKDDAOHBGGLHK
AEKFBONJCDDIECLFJIJKMCHLIK
DLDDLDLDLLDLLLLDLLDDDLDLLL
USB BULK USB KB EMULATION
AMHKHMFOHNGNENEIEPANHOGOCK
AGPEPJAMDKEOFMHMLJAKFDDHKK
AEGNPJCJGIIJCMCEHIJOCEMNPK
AIFBJLBGMHPKMICPIAFFEONCOK
AAPHBAJJCCDBHCPKNDBPGLDBBK
AHLFBOPHCJGEMAMPAAEOMGMJKK
DDDDLDLDLLDLLLLDDDLDDLDLLL
POWERSCAN® D8530 FAMILY
AMHKHMFOHNGNENEIEPANHOGOCK
AGPEPJAMDKEOFMHMLJALFAEHKK
AEONPJCJGIIJCMCEHPLLHLPPJK
AIFBJLBGMHPLNPDFHGDGFIBDOK
AAPHBAJJCGCOPJDIMBCEANODDK
AFKFBPPJPJCAALOIKIECIPIKLK
DDLDLDLDDLDLLLLDDDDDDLDLDL
AMHKHMFOHNGNENEIEPANHOGOCK
AGPEPJAMDKEOFMHMLJAKEDBEKK
AMGNPJCJGIIJCMCFHMNJLBJPHK
AIFBJLBGMHPKNMBGMJOJEHHAOK
AAPHBAJICDHCJBCNKPCNNJNFHK
AFLFBMPJIKPAMFFBBHKCCKNIKK
DLLDLDLDLLDLLLLDDDDDDLDLLL
USB COM EMULATION USB GENERIC HID
AMHKHMFOHNGNENEIEPANHOGOCK
AGPEPJAMDKEOFMHMLJALEAGEKK
AMONPJCJGIIJCMCFHLPMOOKNBK
AIFBJLBGMHPLMLAMDPIKFBLBOK
AAPHBAJICHGNBKOPLNBGLPAHFK
AHKFBNPHFKLEAOHGLPKOGDJLLK
DLDDLDLDDLDLLLLDDDLDDLDLDL
AMHKHMFOHNGNENEIEPANHOGOCK
AGPEPJAMDKEOFMHMLJALEHCGKK
AEONPJCJGIIJCMCFGKKFBJILFK
AIFBJLBGMHPKNJGBENLDAOOCOK
AAPHBAJIDFFKKOLGFOOOMCFNDK
AELFBNNJFAOIIMAMCHHKGHCJJK
DDDDLDLDDLDLLLLDLLDDDLDLDL
RESTORE DEFAULT
AMHKGPAOFNGNENEIEPANHOGOCK
AHHPMBAMDKEOFMHMLJALECHGIK
AKCBPJCJGIIJCMCFGPLCMMMNLK
AEFBJLBGMHPKMOGNKKNDPDMGGK
AAPHBAJIDGHPOJKEFPNCEACBHK
AFKFBKNGLGMOMELLGOPCMJFKIK
DDDDLDLLLDDLLLLDDDLDDLDLDL
7
Page 12
DATALOGIC
WEDGE KEYBOARD NATIONALITY
This parameter default value is restored through the Interface Selection code
and not through the Restore Default code.
Select one of the following keyboard nationality codes.
Belgian English
AMHKHNFMFNGNENEIEPANHOGOCK
AGOEPBIMDKEOFMHMLJAKFHHHKK
AMONPJCJGIIJCMCEHIOEHOELLK
AIFBJLBGMHPLMLDIEKHJAIJDOK
AAPHBAJJDCDBPHGLDNPMOHIBFK
AFKFBKLFPHGAIBPAHBACKOIIIK
DDLDLDLDLLLLLLLDLLDDDLDLDL
French German
AMHKHNFMFNGNENEIEPANHOGOCK
AGPEPBIMDKEOFMHMLJAKEGBEKK
AEGNPJCJGIIJCMCFGMLNOPADNK
AIFBJLBGMHPLMIAAGIAGLNNCOK
AAPHBAJICDFDLOGBKDNOABJJDK
AFLFBJNBKBIAKFOELIEMCJEJLK
DDLDLDLDLLDLLLLDLDDDDLDLDL
AMHKHNFMFNGNENEIEPANHOGOCK
AGPEPBIMDKEOFMHMLJAKFGDHKK
AMGNPJCJGIIJCMCEGIPKHKFBFK
AIFBJLBGMHPLNMDJCBLKLEHAOK
AAPHBAJJCCBAFNLGNPOMLDHNFK
AHLFBLNPACBEKAHKKPKAMFFILK
DLDDLDLDLLDLLLLDLDLDDLDLDL
AMHKHNFMFNGNENEIEPANHOGOCK
AGPEPBIMDKEOFMHMLJALFFEHKK
AMONPJCJGIIJCMCEGPNPCFGDDK
AIFBJLBGMHPKMLCDNHNJKCLBOK
AAPHBAJJCGAPNGHEMNNHNFKPHK
AFKFBKNBNCFAGLFNAHKMIMBLKK
DLLDLDLDDLDLLLLDLDDDDLDLLL
Italian Japanese
AMHKHNFMFNGNENEIEPANHOGOCK
AGPEPBIMDKEOFMHMLJALEFGEKK
AEONPJCJGIIJCMCFGLJILADBLK
AIFBJLBGMHPKNPBKJOGFKLBDOK
AAPHBAJICHEMDFKDLBOFGHELBK
AHKFBINPHBMEGOMDBAEAGAAKKK
DDDDLDLDDLDLLLLDLDLDDLDLLL
AMHKHNFMFNGNENEIEPANHOGOCK
AGOEPBIMDKEOFMHMLJALFEAHKK
AMGNPJCJGIIJCMCEHPMBCBHJNK
AIFBJLBGMHPKNMCCLMBKBOFCOK
AAPHBAJJDGCOHMKJCPMHIBFDHK
AHLFBLLLCHCEEKNHNJAOOHMLJK
DDDDLDLDDLLLLLLDLLLDDLDLLL
Spanish Swedish
AMHKHNFMFNGNENEIEPANHOGOCK
AGPEPBIMDKEOFMHMLJAKFBHFKK
AEGNPJCJGIIJCMCEHJKDINHHBK
AIFBJLBGMHPKMOFEFDIDOLCDOK
AAPHBAJJDACHOJOPDMBEMOCHDK
AEKFBLPBAIEICCAADHHEMBOKJK
DDDDLDLDLLDLLLLDDLDDDLDLDL
AMHKHNFMFNGNENEIEPANHOGOCK
AGPEPBIMDKEOFMHMLJALFCAFKK
AEONPJCJGIIJCMCEHOIGNCEFHK
AIFBJLBGMHPLNJEOKFOAPNOCOK
AAPHBAJJDEDIGCCNCOCPKIPFBK
AGLFBKPPNIAMOJCHJPHIIIKJIK
DDLDLDLDDLDLLLLDDLLDDLDLLL
♦ USA
AMHKHNFMFNGNENEIEPANHOGOCK
AGPEPBIMDKEOFMHMLJAKEBFGKK
AMGNPJCJGIIJCMCFHNOEBICFJK
AIFBJLBGMHPKNKGNBKDPOCIBOK
AAPHBAJIDBGEAKDIEACGHMMDFK
AGKFBJPPKLNMCHJOCAJICNPLJK
DLLDLDLDLLDLLLLDDLLDDLDLDL
8
Page 13
POWERSCAN® D8530 FAMILY
USB KEYBOARD NATIONALITY
This parameter default value is restored through the Interface Selection code
and not through the Restore Default code.
Select one of the following keyboard nationality codes.
Belgian English
AMHKHNEIHNGNENEIEPANHOGOCK
AGOEPBIMDKEOFMHMLJAKEGBGKK
AMONPJCJGIIJCMCFHMKLPKLHPK
AIFBJLBGMHPLNMCPOFAOBCPDOK
AAPHBAJIDCAHEOLPFCIKHIOFFK
AHLFBIKHBNMAADMEBDDIAJCKLK
DDLDLDLDDDLLLLLDDDLDDLDLDL
French German
AMHKHNEIHNGNENEIEPANHOGOCK
AGPEPBIMDKEOFMHMLJAKFHHFKK
AEGNPJCJGIIJCMCEGIPCGLPPJK
AIFBJLBGMHPLNPBHMHHBKHLCOK
AAPHBAJJCDGFAHLFMMKIJOPNDK
AHKFBLMDELCACHNANKHGIOOLIK
DDLDLDLDDDDLLLLDDLLDDLDLDL
AMHKHNEIHNGNENEIEPANHOGOCK
AGPEPBIMDKEOFMHMLJAKEHFGKK
AMGNPJCJGIIJCMCFGMLFPOKNBK
AIFBJLBGMHPLMLCOIOMNKOBAOK
AAPHBAJICCCGOEGCLAJKCMBJFK
AFKFBJMNOILECCEOMNJKGCPKIK
DLDDLDLDDDDLLLLDDLDDDLDLDL
AMHKHNEIHNGNENEIEPANHOGOCK
AGPEPBIMDKEOFMHMLJALEECGKK
AMONPJCJGIIJCMCFGLJAKBJPHK
AIFBJLBGMHPKNMDEHIKOLINBOK
AAPHBAJICGDJGPKAKCKBEKMLHK
AHLFBIMDDIPAOJGJGFJGCLLJJK
DLLDLDLDLDDLLLLDDLLDDLDLLL
Italian Japanese
AMHKHNEIHNGNENEIEPANHOGOCK
AGPEPBIMDKEOFMHMLJALFEAFKK
AEONPJCJGIIJCMCEGPNHDEMNPK
AIFBJLBGMHPKMIANDBBCLBHDOK
AAPHBAJJCHHKIMHHNOJDPICPBK
AFLFBKMNJLGEOMPHHCHKMHKIJK
DDDDLDLDLDDLLLLDDLDDDLDLLL
AMHKHNEIHNGNENEIEPANHOGOCK
AGOEPBIMDKEOFMHMLJALEFGGKK
AMGNPJCJGIIJCMCFHLIOKFIFJK
AIFBJLBGMHPKMLDFBDGNAEDCOK
AAPHBAJIDGBIMFHNEALBBODHHK
AFKFBJKJMNIEMIODLLDEEAGJKK
DDDDLDLDLDLLLLLDDDDDDLDLLL
Spanish Swedish
AMHKHNEIHNGNENEIEPANHOGOCK
AGPEPBIMDKEOFMHMLJAKEABEKK
AEGNPJCJGIIJCMCFHNOMAJILFK
AIFBJLBGMHPKNJEDPMPEPBEDOK
AAPHBAJIDABBFADLFDGCFBEDDK
AGLFBJODOCOIKADEFFEOGGEIKK
DDDDLDLDDDDLLLLDLDLDDLDLDL
AMHKHNEIHNGNENEIEPANHOGOCK
AGPEPBIMDKEOFMHMLJALEDGEKK
AEONPJCJGIIJCMCFHKMJFGLJDK
AIFBJLBGMHPLMOFJAKJHOHICOK
AAPHBAJIDEAONLPJEBFJDHJBBK
AEKFBIONDCKMGLBDPNECCPALLK
DDLDLDLDLDDLLLLDLDDDDLDLLL
♦ USA
AMHKHNEIHNGNENEIEPANHOGOCK
AGPEPBIMDKEOFMHMLJAKFADHKK
AMGNPJCJGIIJCMCEHJKLJMNJNK
AIFBJLBGMHPKMNHKLFEIPIOBOK
AAPHBAJJDBFCLDOMCPFAODKHFK
AELFBLONEBHMKFKKECKCIKFJKK
DLLDLDLDDDDLLLLDLDDDDLDLDL
9
Page 14
DATALOGIC
READING PARAMETERS
GOOD READ SPOT DURATION
Disabled
AMHKHNGMFNGNENEIEPANHOGOCK
AGPEPBIMDKEOFMHMLJAKEEGEKK
AMGNPJCJGIIJCMCEHMNEPKCDPK
AIFBJLBGMHPLNKHNAEHPNLGDOK
AAPHBAJIDFDNGNPJFBDBHFOHHK
AHLFBOIEEHIOMFIGJFGGIFJKKK
DDDDLDLDDDLLLLLDDLDDDLDLLL
Medium Long
AMHKHNGMFNGNENEIEPANHOGOCK
AGPEPBIMDKEOFMHMLJAKEDCGKK
AEGNPJCJGIIJCMCEGNINANAFLK
AIFBJLBGMHPKMIBAHGEGIEDAOK
AAPHBAJICHAKNJKALCMJAILNBK
AEKFBOKKENNCEHPMANLCIBCIIK
DLDDLDLDDDLLLLLDLDLDDLDLLL
Successful reading can be signaled by a good read green spot.
♦ Short
AMHKHNGMFNGNENEIEPANHOGOCK
AGPEPBIMDKEOFMHMLJALEAFGKK
AEONPJCJGIIJCMCEGKKIFCDHNK
AIFBJLBGMHPLNPAKIACFJCPBOK
AAPHBAJICDBFFCGCKAPCGOGPDK
AGLFBPKEJNJGIMNLKFLOMIGLJK
DLLDLDLDLDLLLLLDLDDDDLDLDL
AMHKHNGMFNGNENEIEPANHOGOCK
AGPEPBIMDKEOFMHMLJALFAHFKK
AMONPJCJGIIJCMCFGOOPMHGFFK
AIFBJLBGMHPLMLDDMJJJJLFDOK
AAPHBAJJCCFGLBLFNMMANMILFK
AELFBNKKDOACIJEFLCFCCEHKJK
DDDDLDLDLDLLLLLDLDLDDLDLDL
10
Page 15
POWERSCAN® D8530 FAMILY
DEFAULT CONFIGURATION
RS-232 Standard DEFAULT SETTINGS
115200 baud, no parity, 8 data bits, 1 stop bit, no handshake, no protocol, FIFO
enabled, intercharacter delay = 0, intercode delay = 0, serial trigger lock disabled, serial
trigger lock disable character = NUL, serial trigger lock enable character = NUL, RX
Timeout = 10 sec
USB COM Emulation DEFAULT SETTINGS
no handshake, no protocol, FIFO enabled, intercharacter delay = 0, intercode
delay = 0
USB Keyboard Emulation DEFAULT SETTINGS
USA keyboard*, intercharacter delay = 0, intercode delay = 0, FIFO enabled,
keyboard speed = normal
WEDGE Communication DEFAULT SETTINGS
USA keyboard*, CapsLock OFF, CapsLock Auto-Recognition ON, NumLock OFF,
intercharacter delay = 0, intercode delay = 0
DATA FORMAT – Symbology Independent Parameters
custom code identifier disabled, code identifier disabled, code length disabled
Default headers and terminators*:
- RS-232: no header, terminator = CR-LF
- USB BULK: no header, terminator = CR-LF
- USB COM: no header, terminator = CR-LF
- USB Generic HID: no header, terminator = CR-LF
- Wedge: no header, terminator = ENTER
- USB Keyboard: no header, terminator = ENTER
DATA FORMAT – Symbology Dependent Parameters
symbology specific format = select all, no headers, no terminators, symbology
character substitution disabled, symbology character deletion disabled
DATA FORMAT – Concatenation
Concatenation disabled, 2 EAN/UPC codes concatenated, Set First Concatenated
Code Length 000 = any length, Set Second Concatenated Code Length 000 = any
length, Set Third Concatenated Code Length 000 = any length, Set Fourth
Concatenated Code Length 000 = any length, Concatenation with Intercode Delay
disabled, Concatenation Timeout 10 seconds, Concatenation Failure
Transmission = Tx codes causing failure, Transmission after Timeout = No code
transmission, Concatenation Result Code ID = No code Identifier
ADVANCED FORMATTING PARAMETERS
format disabled
CAMERA CONTROL
exposure mode = automatic, based on entire image
POWER SAVE
Illumination power = ON
* The default values of these parameters are set when reading the interface
selection.
11
Page 16
DATALOGIC
CODE SELECTION
issue identical codes = enable
enabled codes
Standard Code 39: no check digit control, variable code length;
EAN 8/EAN 13 / UPC A/UPC E without ADD ON: UPCE expansion disabled
Interleaved 2/5: check digit control and transmission, variable code length
Code 128: variable code length
PDF417
Datamatrix
QR
: rectangular, normal and inverted, variable code length
disabled codes
Code 32, Codabar, Code 93, EAN 128, Aztec, GS1 DataBar™, Micro
PDF417, Postal Codes, Maxicode, Composite Codes
READING PARAMETERS
trigger type normal, trigger level mode, flash on = 2 sec, flash off = 2 sec,
beeper tone = tone 1, beeper volume = high, beeper duration = 50 ms, user
defined beeper = tone 1, user defined beeper volume = high, user defined
beeper duration = 100 ms, code per scan = one code per scan, read per
cycle = one read per cycle, scan timeout = 5 sec, central code transmission
enabled, order by code length disabled, order by code symbology disabled,
autoscan mode disabled, autoscan aiming system enabled, autoscan
hardware trigger enabled, autoscan illumination system disabled, stand
autoscan mode = normal, aiming system delay = disabled, good read spot =
short, safety time = 500 ms
IMAGE FORMATTING
Image Preset 1, 2, 3, 4
image format = JPEG, resolution = full (1280 x 1024), set JPEG quality
factor = 50, brightness = 0%, contrast = 0%, color depth = 256 gray level.
12
Page 17
OPERATING TEST
EAN-13 Code 39 (Standard)
POWERSCAN® D8530 FAMILY
1 234567 000992
Code 128 PDF417
test
QR Data Matrix (Normal)
17162
13
Page 18
DATALOGIC
TECHNICAL FEATURES
PowerScan® D8530 Family Common Features
Electrical Features
Operating Voltage 5 to 30 V
Power Consumption
@ 5V
@30V
Communications Features
Standard Interfaces
Proprietary Interfaces
Environmental Features
Operating Temperature -10° to +55° C (+14° to +131° F)
Storage Temperature -20° to +70° C (-4° to +158° F)
Humidity 0 to 95% NC
Drop Resistance
IP Sealing
Mechanical Features
Dimensions
Weight 295 g / 10.4 oz (without cable)
Decoding Capability
1D Interleaved 2 of 5, Code 39, Code 32, Code 128, EAN
2D
Postal Codes
Imaging Options
Image 1280x1024 pixels (Full Resolution)
640 x 512 pixel format (Half Resolution);
Graphic Format JPEG, 256 gray levels
TIFF, 2, 16, 256 gray levels
Optical Features
Sensor
Illuminator
Wavelength In the range 630 ~ 670 nm
LED Safety Class Class 1 to EN 60825-1
Aiming System
Wavelength 650 nm
Laser Safety Class Class 2 - EN 60825-1; Class II CDRH
Ambient light 0 - 100000 lux
(Typical) 600 mA
(Typical) 100 mA
RS-232, Keyboard emulation AT IBM, USB COM
emulation, USB Keyboard emulation
USB Bulk, USB Generic HID
2 m / 6.6 ft (over 50 drops to concrete)
IP65
20.8 x 6.6 x 11 cm / 8.1 x 2.6 x 4.3 in
128, Code93, UPC/EAN/JAN, Codabar, GS1 DataBar™
Aztec, PDF417, Micro PDF417, Macro PDF417,
Maxicode, DataMatrix (ECC200), QR, Composite Codes
PLANET, Japan Post, Australia Post, KIX Code, Royal
Mail Code (RM4SCC)
1280 x 1024 pixel element, 2D CMOS Array
LED array
Visible Laser Diode
14
Page 19
POWERSCAN® D8530 FAMILY
PowerScan® D8530™
Optical Features
Focus distance 140 mm
Field of view 28° (H) x 23° (V)
Horizontal field of view at
distance (d) in mm
Vertical field of view at
distance (d) in mm
Max Resolution
Linear codes -
mm (mils)
0.52d + 15
0.42d + 12
PDF 417 –
mm (mils)
Datamatrix –
mm (mils)
0.10 (4 mils) 0.10 (4 mils) 0.17 (6.6 mils)
Depth of field*
1D (linear): X-dimension
mm (mils)
DOF
cm (in)
Code39 0.13 (5) 7.5 to 15.5
(2.95 to 6.10)
0.5 (20) 5.5 to 36.5
(2.17 to 14.37)
EAN13 0.33 (13) 5.0 to 27
(1.97 to 10.63)
2D: X-dimension
mm (mils)
DOF
cm (in)
PDF417 0.13 (5) 8.0 to 18.5
(3.15 to 7.28)
0.25 (10) 4.0 to 25.5
(1.57 to 10.04)
QR
0.19 (7.5) 8.0 to 16.5
(3.15 to 6.5)
0.25 (10) 7.0 to 19.5
(2.76 to 7.68)
DataMatrix 0.19 (7.5) 8.0 to 16.5
(3.15 to 6.5)
0.25 (10) 7.0 to 19.5
(2.76 to 7.68)
Skew ±40°
Pitch ±35°
Rotation 360°
Print Contrast (Min.) 15%
• Reading distances are measured from the nose of the reader.
NOTE: Typical performance at 20ºC / 68ºF on high quality barcodes.
15
Page 20
DATALOGIC
PowerScan® D8530™ HD
Optical Features
Focus distance 65 mm
Field of view 27° (H) x 22° (V)
Horizontal field of view at
distance (d) in mm
Vertical field of view at
distance (d) in mm
Max Resolution
Linear codes -
mm (mils)
0.05 (2 mils) 0.08 (3 mils) 0.10 (4 mils)
Depth of field*
1D (linear): X-dimension
mm (mils)
0.50d + 13
0.40d + 10
PDF 417 –
mm (mils)
Datamatrix –
mm (mils)
DOF
cm (in)
Code39 0.08 (3) 4.5 to 8.0 (1.77 to 3.15)
0.13 (5) 3.5 to 9.5 (1.38 to 3.74)
0.51 (20) 6.0 to 18.5 (2.36 to 7.28)
EAN13 0.33 (13) 5.0 to 14 (1.97 to 5.51)
2D: X-dimension
mm (mils)
DOF
cm (in)
PDF417 0.08 (3) 5.0 to 8.5
(1.97 to 3.35)
0.13 (5) 4.5 to 9.5
(1.77 to 3.74)
0.25 (10) 3.0 to 13.0
(1.18 to 5.12)
QR
0.10 (4) 5.5 to 7.5
(2.17 to 2.95)
0.19 (7.5) 5.0 to 8.0
(1.97 to 3.15)
0.25 (10) 4.5 to 9.5
(1.77 to 3.74)
DataMatrix
0.10 (4) 5.5 to 7.5
(2.17 to 2.95)
0.19 (7.5) 5.0 to 8.0
(1.97 to 3.15)
0.25 (10) 4.5 to 9.5
(1.77 to 3.74)
Skew ±40°
Pitch ±35°
Rotation 360°
Print Contrast (Min.) 23%
• Reading distances are measured from the nose of the reader.
NOTE: Typical performance at 20ºC / 68ºF on high quality barcodes.
16
Page 21
POWERSCAN® D8530 FAMILY
PowerScan® D8530™ WA
Optical Features
Focus distance 115 mm
Field of view 54° (H) x 45° (V)
Horizontal field of view at
distance (d) in mm
Vertical field of view at
distance (d) in mm
Max Resolution
Linear codes -
mm (mils)
0.13 (5 mils) 0.13 (5 mils) 0.19 (7.5 mils)
Depth of field*
1D (linear): X-dimension
mm (mils)
1.04d + 40
0.40d + 10
PDF 417 –
mm (mils)
Datamatrix –
mm (mils)
DOF
cm (in)
Code39 0.13 (5) 2.5 to 10.0
(0.98 to 3.94)
0.51 (20) 1.5 to 32
(0.59 to 12.60)
EAN 13 0.33 (13) 1.5 to 26.0
(0.59 to 10.24)
2D: X-dimension
mm (mils)
DOF
cm (in)
PDF417 0.13 (5) 3.0 to 10.5
(1.18 to 4.13)
0.25 (10) 1.5 to 21.5
(0.59 to 8.46)
QR
0.19 (7.5) 5.5 to 8.5
(2.17 to 3.35)
0.25 (10) 3.0 to 12.5
(1.18 to 4.92)
DataMatrix 0.19 (7.5) 5.5 to 8.5
(2.17 to 3.35)
0.25 (10) 3.0 to 12.5
(1.18 to 4.92)
Skew ±40°
Pitch ±35°
Rotation 360°
Print Contrast (Min.) 15%
• Reading distances are measured from the nose of the reader.
NOTE: Typical performance at 20ºC / 68ºF on high quality barcodes.
17
Page 22
DATALOGIC
SERVICE AND SUPPORT
Datalogic provides several services as well as technical support through its
website. Log on to www.scanning.datalogic.com
indicated for further information including:
• PRODUCTS
Search through the links to arrive at your product page where you can
download specific Manuals and Software & Utilities including:
- Datalogic Aladdin™ a multi-platform utility program that allows device
configuration using a PC. It provides RS-232 interface configuration as
well as configuration barcode printing.
• SERVICE & SUPPORT
- Technical Support – Product documentation and programming guides
and Technical Support Department in the world
- Service Programs – Warranty Extensions and Maintenance
Agreements
- Repair Services – Flat Rate Repairs and Return Material Authorization
(RMA) Repairs.
- Downloads – Manuals & Documentation, Data Sheets, Product
Catalogues, etc.
and click on the links
• CONTACT US
Information Request Form and Sales & Service Network
WARRANTY
Datalogic warranties this product against defects in workmanship and materials,
for a period of 3 years from the date of shipment, provided that the product is
operated under normal and proper conditions.
Datalogic has the faculty to repair or replace the product, these provisions do
not prolong the original warranty term.
The warranty does not apply to any product that has been subject to misuse,
accidental damage, unauthorized repair or tampering.
PATENTS
This product is covered by one or more of the following patents:
Design Pat.: AU 310201; AU 310202; CN 693980; HK 0602013.5M001; HK
0602013.5M002; JP 1305693; KR 30-0460940.
US Pat.: 6,478,226 B2; 6,512,218 B1; 6,808,114 B1; 6,877,664 B1; 6,997,385
B2; 7,053,954 B1; 7,102,116 B2; 7,282,688 B2.
European Pat.: 996,284 B1; 999,514 B1; 1,128,315 B1.
Additional patents pending.
18
Page 23
COMPLIANCE
POWERSCAN® D8530 FAMILY
Aiming System Imager
Beam Output Window
CE COMPLIANCE
This is a Class A product . In a domestic environment this
product may cause radio interference, in which case the user
may be required to take adequate measures.
WARNING
FCC COMPLIANCE
Modifications or changes to this equipment without the expressed written
approval of Datalogic could void the authority to use the equipment.
This device complies with PART 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference which may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
19
Page 24
DATALOGIC
LASER SAFETY
The PowerScan® D8530 hand-held reader is a Class 1 LED product regarding
its Illuminator and a Class 2 laser product regarding its Aiming System.
LED Illuminator
The use of an illuminator in the PowerScan® D8530 hand-held reader is a
Class 1 LED product:
ILLUMINATORE LED CLASSE 1
AUSLEUCHTER LED KLASSE 1
ILLUMINATEUR A LED DE CLASSE 1
ILUMINADOR LED DE CLASE 1
Aiming System
The PowerScan® D8530 aiming system meets the Class 2 requirements for
laser safety.
I D F E
LA LUCE LASER
È VISIBILE
ALL'OCCHIO
UMANO E VIENE
EMESSA DALLA
FINESTRA
INDICATA
NELLA FIGURA.
LUCE LASER
NON FISSARE IL
FASCIO
APPARECCHIO
LASER DI
CLASSE 2
MASSIMA
POTENZA
D'USCITA:
LUNGHEZZA
D'ONDA
EMESSA:
CONFORME A
EN 60825-1
(2001)
DIE LASERSTRAHLUNG IST FÜR
DAS MENSCHLICHE
AUGE SICHTBAR UND
WIRD AM STRAHLAUS
TRITTSFENSTER
AUSGESENDET (SIEHE
BILD)
LASERSTRAHLUNG
NICHT IN DEN STRAHL
BLICKEN PRODUKT
DER LASERKLASSE 2
MAXIMALE
AUSGANGSLEISTUNG:
WELLENLÄGE:
ENTSPR. EN 60825-1
(2001)
LE RAYON
LASER EST
VISIBLE À L'OEIL
NU ET IL EST
ÉMIS PAR LA
FENÊTRE
DÉSIGNÉE SUR
L'ILLUSTRATION
DANS LA FIGURE
RAYON LASER
EVITER DE
REGARDER LE
RAYON
APPAREIL LASER
DE CLASSE 2
PUISSANCE DE
SORTIE:
LONGUEUR
D'ONDE EMISE:
CONFORME A EN
60825-1 (2001)
A LUZ LÁSER ES
VISIBLE AL OJO
HUMANO Y ES
EMITIDA POR LA
VENTANA
INDICADA EN LA
FIGURA.
RAYO LÁSER NO
MIRAR FIJO EL
RAYO APARATO
LÁSER DE CLASE
2 MÁXIMA
POTENCIA DE
SALIDA:
LONGITUD DE
ONDA EMITIDA:
CONFORME A EN
60825-1 (2001)
20
Page 25
POWERSCAN® D8530 FAMILY
ENGLISH
The following information is provided to comply with the rules imposed by
international authorities and refers to the correct use of your terminal.
STANDARD LASER SAFETY REGULATIONS
This product conforms to the applicable requirements of both CDRH 21 CFR
1040 and EN 60825-1 at the date of manufacture.
For installation, use and maintenance, it is not necessary to open the device.
Use of controls or adjustments or performance of
procedures other than those specified herein may result in
exposure to hazardous visible laser light.
WARNING
The product utilizes a low-power laser diode. Although staring directly at the laser
beam momentarily causes no known biological damage, avoid staring at the beam
as one would with any very strong light source, such as the sun. Avoid that the
laser beam hits the eye of an observer, even through reflective surfaces such as
mirrors, etc.
ITALIANO
Le seguenti informazioni vengono fornite dietro direttive delle autorità
internazionali e si riferiscono all’uso corretto del terminale.
NORMATIVE STANDARD PER LA SICUREZZA LASER
Questo prodotto risulta conforme alle normative vigenti sulla sicurezza laser alla
data di produzione: CDRH 21 CFR 1040 e EN 60825-1.
Non si rende mai necessario aprire l’appa-recchio per motivi di installazione,
utilizzo o manutenzione.
ATTENZIONE
Il prodotto utilizza un diodo laser a bassa potenza. Sebbene non siano noti
danni riportati dall’occhio umano in seguito ad una esposizione di breve durata,
evitare di fissare il raggio laser così come si eviterebbe qualsiasi altra sorgente
di luminosità intensa, ad esempio il sole. Evitare inoltre di dirigere il raggio laser
negli occhi di un osservatore, anche attraverso superfici riflettenti come gli
specchi.
L'utilizzo di procedure o regolazioni differenti da quelle
descritte nella documentazione può provocare
un'esposizione pericolosa a luce laser visibile.
21
Page 26
DATALOGIC
DEUTSCH
Die folgenden Informationen stimmen mit den Sicherheitshinweisen überein, die
von internationalen Behörden auferlegt wurden, und sie beziehen sich auf den
korrekten Gebrauch vom Terminal.
NORM FÜR DIE LASERSICHERHEIT
Dies Produkt entspricht am Tag der Herstellung den gültigen EN 60825-1 und
CDRH 21 CFR 1040 Normen für die Lasersicherheit.
Es ist nicht notwendig, das Gerät wegen Betrieb oder Installations-, und
Wartungs-Arbeiten zu öffnen.
Jegliche Änderungen am Gerät sowie Vorgehensweisen, die
nicht in dieser Betriebsanleitung beschreiben werden,
können ein gefährliches Laserlicht verursachen.
ACHTUNG
Der Produkt benutzt eine Laserdiode. Obwohl zur Zeit keine Augenschäden von
kurzen Einstrahlungen bekannt sind, sollten Sie es vermeiden für längere Zeit in
den Laserstrahl zu schauen, genauso wenig wie in starke Lichtquellen (z.B. die
Sonne). Vermeiden Sie es, den Laserstrahl weder gegen die Augen eines
Beobachters, noch gegen reflektierende Oberflächen zu richten.
FRANÇAIS
Les informations suivantes sont fournies selon les règles fixées par les autorités
internationales et se réfèrent à une correcte utilisation du terminal.
NORMES DE SECURITE LASER
Ce produit est conforme aux normes de sécurité laser en vigueur à sa date de
fabrication: CDRH 21 CFR 1040 et EN 60825-1.
Il n’est pas nécessaire d’ouvrir l’appareil pour l’installation, l’utilisation ou
l’entretien.
ATTENTION
Le produit utilise une diode laser. Aucun dommage aux yeux humains n’a été
constaté à la suite d’une exposition au rayon laser. Eviter de regarder fixement
le rayon, comme toute autre source lumineuse intense telle que le soleil. Eviter
aussi de diriger le rayon vers les yeux d’un observateur, même à travers des
surfaces réfléchissantes (miroirs, par exemple).
22
L'utilisation de procédures ou réglages différents de ceux
donnés ici peut entraîner une dangereuse exposition à
lumière laser visible.
Page 27
POWERSCAN® D8530 FAMILY
ESPAÑOL
Las informaciones siguientes son presentadas en conformidad con las
disposiciones de las autoridades internacionales y se refieren al uso correcto
del terminal.
NORMATIVAS ESTÁNDAR PARA LA SEGURIDAD LÁSER
Este aparato resulta conforme a las normativas vigentes de seguridad láser a la
fecha de producción: CDRH 21 CFR 1040 y EN 60825-1.
No es necesario abrir el aparato para la instalación, la utilización o la
manutención.
La utilización de procedimientos o regulaciones diferentes
de aquellas describidas en la documentación puede causar
una exposición peligrosa a la luz láser visible.
ATENCIÓN
El aparato utiliza un diodo láser a baja potencia. No son notorios daños a los
ojos humanos a consecuencia de una exposición de corta duración. Eviten de
mirar fijo el rayo láser así como evitarían cualquiera otra fuente de luminosidad
intensa, por ejemplo el sol. Además, eviten de dirigir el rayo láser hacia los ojos
de un observador, también a través de superficies reflectantes como los
espejos.
The PowerScan® D8530 Hand-Held Reader is not
user-serviceable. Opening the case of the unit can cause
internal damage and will void the warranty.
CAUTION
POWER SUPPLY
This device is intended to be supplied by a UL Listed or CSA Certified Power
Unit marked "Class 2" or "LPS" output rated 5-30 V, minimum 0.75 A which
supplies power directly to the scanner via the jack connector on the cable.
23
Page 28
DATALOGIC
WEEE COMPLIANCE
Waste Electrical and Electronic Equipment
(WEEE) Statement
English
For information about the disposal of Waste Electrical and Electronic Equipment
(WEEE), please refer to the w
Italian
Per informazioni sullo smaltimento delle apparecchiature elettriche ed
elettroniche consultare il sito Web www.scanni
French
Pour toute information relative à l’élimination des déchets électroniques
(WEEE), veuillez consulter le site internet www.scanni
German
Informationen zur Entsorgung von Elektro- und Elektronik- Altgeräten (WEEE)
erhalten Sie auf der Webseite www.scanni
Spanish
Si desea información acerca de los procedimientos para el desecho de los
residuos del equipo eléctrico y
www.s
Portuguese
Para informações sobre a disposição de Sucatagem de Equipamentos Elétricos
e Eletrônicos (WEEE -Waste Electrical and Electronic Equipment), consultar o
site w
Chinese
有关处理废弃电气电子设备 (WEEE)的信息，
请参考Datalogic公司的网站：http://www.scanning.datalogic.com/。
Japanese
廃電気電子機器(ＷＥＥＥ)の処理についての関連事項はDatalogicのサイト
canning.datal
eb www.s
ogic.com.
canning.datal
ebsite at www.s
electrónico (WEEE), visite la página Web
ogic.com.
canning.datal
ng.datal
ng.datal
ogic.com.
ogic.com.
ogic.com.
ng.datal
ogic.com.
www.scanning.datalogic.com,
24
をご参照下さい。
Page 29
NOTES
POWERSCAN® D8530 FAMILY
25
Page 30
DATALOGIC
NOTES
26
Page 31
DECLARATION OF CONFORMITY
EC-049
REV.: 0
Pag.: 1 di 1
08 Datalogic Scanning Group Srl
Via S. Vitalino, 13
Lippo di Calderara di Reno (BO)
dichiara che
declares that the
déclare que le
bescheinigt ,daß das Gerät
declare que el
POWERSCAN D8530 ; 2D Reader
e tutti i suoi modelli
and all its models
et tous les modèles
und seine modelle
y todos sus modelos
sono conformi alle Direttive del Consiglio Europeo sottoelencate:
are in conformity with the requirements of the European Council Directives listed below
sont conformes aux spécifications des Directives de l’Union Européenne ci-dessous:
den nachstehenden angeführten Direktiven des Europäischen Rats:
cumple con los requisitos de las Directivas del Consejo Europeo, según la lista siguiente:
89/336/EEC EMC Directive e 92/31/EEC, 93/68 /EEC emendamenti successivi
and further amendments
et ses successifs amendements
und späteren Abänderungen
y succesivas enmiendas
Basate sulle legislazioni degli Stati membri in relazione alla compatibilità elettromagnetica
ed alla sicurezza dei prodotti.
On the approximation of the laws of Member States relating to electromagnetic
compatibility and product safety.
Basée sur la législation des Etats membres relative à la compatibilté électromagnétique et
à la sécurité des produits.
Über die Annäherung der Gesetze der Mitgliedsstaaten in bezug auf elektromagnetische
Verträglichkeit und Produktsicherheit entsprechen.
Basado en la aproximación de las leyes de los Países Miembros respecto a la
compatibilidad electromagnética y las Medidas de seguridad relativas al producto.
Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti:
This declaration is based upon compliance of the products to the following standards:
Cette déclaration repose sur la conformité des produits aux normes suivantes:
Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht:
Esta declaración se basa en el cumplimiento de los productos con las siguientes normas:
55022 ( CLASS A ITE ), AUGUST 1994:
EN
A
MENDMENT A1 ( CLASS A ITE ), OCTOBER
2000:
EN 61000-6-2, OCTOBER 2001:
Lippo di Calderara, February 11th , 2008 Ruggero Cacioppo
40012 Italy
IMITS AND METHODS OF MEASUREMENTS OF RADIO
L
DISTURBANCE CHARACTERISTICS OF INFORMATION
TECHNOLOGY EQUIPMENT
ELECTROMAGNETIC COMPATIBILITY (EMC)
PART 6-2: GENERIC STANDARDS - IMMUNITY FOR
INDUSTRIAL ENVIRONMENTS
Quality Assurance Manager
Page 32
www.scanning.datalogic.com
PowerScan D8530 Family
Datalogic Scanning, Inc.
959 Terry Street
Eugene, OR 97402
Telephone: (541) 683-5700
Fax: (541) 345-7140
Australia
Datalogic Scanning Pty Ltd
North Ryde, Australia
Telephone: [61] (2) 9870 3200
Fax: [61] (2) 9878 8688
France and Benelux
Datalogic Scanning Sarl
LES ULIS Cedex, France
Telephone: [33].01.64.86.71.00
Fax: [33].01.64 46.72.44
Germany
Datalogic Scanning GmbH
Darmstadt, Germany
Telephone: 49 (0) 61 51/93 58-0
Fax: 49 (0) 61 51/93 58 58
Italy
Datalogic Scanning SpA
Vimercate (MI), Italy
Telephone: [39] (0) 39/62903.1
Fax: [39] (0) 39/6859496
Japan
Datalogic Scanning KK
Shinagawa, Tokyo, Japan
Telephone: 81 (0)3 3491 6761
Fax: 81 (0)3 3491 6656
Latin America
Datalogic Scanning, Inc
Miami, Florida, USA
Telephone: (305) 591-3222
Fax: (305) 591-3007
Spain and Portugal
Datalogic Scanning Sarl
Sucursal en España
Madrid, Spain
Telephone: 34 91 746 28 60
Fax: 34 91 742 35 33
United Kingdom
Datalogic Scanning LTD
Watford, England
Telephone: 44 (0) 1923 809500
Fax: 44 (0) 1923 809 505
©2008 Datalogic Scanning, Inc.
820001910 (Rev. A)
02/08
Loading...